Currently, the calculation of ack signal strength is incorrect.
This is because before calculating the ack signal strength, ath11k need
to determine whether the hardware and firmware support db2dbm. If the
hardware and firmware support db2dbm, do not need to add noise floor,
otherwise, need to add noise floor.
Besides, the value of ack_rssi passed by firmware to ath11k should be a
signed number, so change its type to s8.
After that, "iw wlan0 station dump" show the correct ack signal strength.
Such as:
root@CDCCSTEX0799733-LIN:~# iw wlp88s0 station dump
Station 00:03:7f:12:df:df (on wlp88s0)
inactive time: 75 ms
rx bytes: 11599
rx packets: 99
tx bytes: 9029
tx packets: 81
tx retries: 4
tx failed: 0
rx drop misc: 2
signal: -16 dBm
signal avg: -24 dBm
tx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
tx duration: 9230 us
rx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
rx duration: 7201 us
last ack signal:-23 dBm
avg ack signal: -22 dBm
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <[email protected]>
---
drivers/net/wireless/ath/ath11k/dp_tx.c | 16 ++++++++++++----
drivers/net/wireless/ath/ath11k/dp_tx.h | 4 ++--
drivers/net/wireless/ath/ath11k/hal_tx.h | 4 ++--
3 files changed, 16 insertions(+), 8 deletions(-)
diff --git a/drivers/net/wireless/ath/ath11k/dp_tx.c b/drivers/net/wireless/ath/ath11k/dp_tx.c
index 21819b741701..8522c67baabf 100644
--- a/drivers/net/wireless/ath/ath11k/dp_tx.c
+++ b/drivers/net/wireless/ath/ath11k/dp_tx.c
@@ -353,8 +353,12 @@ ath11k_dp_tx_htt_tx_complete_buf(struct ath11k_base *ab,
if (ts->acked) {
if (!(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
info->flags |= IEEE80211_TX_STAT_ACK;
- info->status.ack_signal = ATH11K_DEFAULT_NOISE_FLOOR +
- ts->ack_rssi;
+ info->status.ack_signal = ts->ack_rssi;
+
+ if (!test_bit(WMI_TLV_SERVICE_HW_DB2DBM_CONVERSION_SUPPORT,
+ ab->wmi_ab.svc_map))
+ info->status.ack_signal += ATH11K_DEFAULT_NOISE_FLOOR;
+
info->status.flags |=
IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
} else {
@@ -584,8 +588,12 @@ static void ath11k_dp_tx_complete_msdu(struct ath11k *ar,
if (ts->status == HAL_WBM_TQM_REL_REASON_FRAME_ACKED &&
!(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
info->flags |= IEEE80211_TX_STAT_ACK;
- info->status.ack_signal = ATH11K_DEFAULT_NOISE_FLOOR +
- ts->ack_rssi;
+ info->status.ack_signal = ts->ack_rssi;
+
+ if (!test_bit(WMI_TLV_SERVICE_HW_DB2DBM_CONVERSION_SUPPORT,
+ ab->wmi_ab.svc_map))
+ info->status.ack_signal += ATH11K_DEFAULT_NOISE_FLOOR;
+
info->status.flags |= IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
}
diff --git a/drivers/net/wireless/ath/ath11k/dp_tx.h b/drivers/net/wireless/ath/ath11k/dp_tx.h
index 61be2265e09f..795fe3b8fa0d 100644
--- a/drivers/net/wireless/ath/ath11k/dp_tx.h
+++ b/drivers/net/wireless/ath/ath11k/dp_tx.h
@@ -1,7 +1,7 @@
/* SPDX-License-Identifier: BSD-3-Clause-Clear */
/*
* Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
- * Copyright (c) 2021, 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2021, 2023-2024 Qualcomm Innovation Center, Inc. All rights reserved.
*/
#ifndef ATH11K_DP_TX_H
@@ -13,7 +13,7 @@
struct ath11k_dp_htt_wbm_tx_status {
u32 msdu_id;
bool acked;
- int ack_rssi;
+ s8 ack_rssi;
u16 peer_id;
};
diff --git a/drivers/net/wireless/ath/ath11k/hal_tx.h b/drivers/net/wireless/ath/ath11k/hal_tx.h
index c5e88364afe5..46d17abd808b 100644
--- a/drivers/net/wireless/ath/ath11k/hal_tx.h
+++ b/drivers/net/wireless/ath/ath11k/hal_tx.h
@@ -1,7 +1,7 @@
/* SPDX-License-Identifier: BSD-3-Clause-Clear */
/*
* Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
- * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2022, 2024 Qualcomm Innovation Center, Inc. All rights reserved.
*/
#ifndef ATH11K_HAL_TX_H
@@ -54,7 +54,7 @@ struct hal_tx_info {
struct hal_tx_status {
enum hal_wbm_rel_src_module buf_rel_source;
enum hal_wbm_tqm_rel_reason status;
- u8 ack_rssi;
+ s8 ack_rssi;
u32 flags; /* %HAL_TX_STATUS_FLAGS_ */
u32 ppdu_id;
u8 try_cnt;
base-commit: a116bf2be795eb1db75fa6a48aa85c397be001a6
--
2.34.1
On 6/10/2024 7:25 PM, Lingbo Kong wrote:
> Currently, the calculation of ack signal strength is incorrect.
>
> This is because before calculating the ack signal strength, ath11k need
> to determine whether the hardware and firmware support db2dbm. If the
> hardware and firmware support db2dbm, do not need to add noise floor,
> otherwise, need to add noise floor.
>
> Besides, the value of ack_rssi passed by firmware to ath11k should be a
> signed number, so change its type to s8.
>
> After that, "iw wlan0 station dump" show the correct ack signal strength.
>
> Such as:
> root@CDCCSTEX0799733-LIN:~# iw wlp88s0 station dump
> Station 00:03:7f:12:df:df (on wlp88s0)
> inactive time: 75 ms
> rx bytes: 11599
> rx packets: 99
> tx bytes: 9029
> tx packets: 81
> tx retries: 4
> tx failed: 0
> rx drop misc: 2
> signal: -16 dBm
> signal avg: -24 dBm
> tx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
> tx duration: 9230 us
> rx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
> rx duration: 7201 us
> last ack signal:-23 dBm
> avg ack signal: -22 dBm
>
> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
>
> Signed-off-by: Lingbo Kong <[email protected]>
Acked-by: Jeff Johnson <[email protected]>
Hi Lingbo,
On 6/10/24 7:25 PM, Lingbo Kong wrote:
> Currently, the calculation of ack signal strength is incorrect.
>
> This is because before calculating the ack signal strength, ath11k need
> to determine whether the hardware and firmware support db2dbm. If the
> hardware and firmware support db2dbm, do not need to add noise floor,
> otherwise, need to add noise floor.
This oatch got me checking on some devices we have running ath11k
(WCN6855). I don't see any "ack signal" property but I noticed the
signal avg does not seem correct:
signal: -55 [-62, -56] dBm
signal avg: 105 dBm
Every other device besides ath11k has a signal avg close to or equal to
the signal. Do you think there is also an issue with this property? not
just the ack signal?
Thanks,
James
>
> Besides, the value of ack_rssi passed by firmware to ath11k should be a
> signed number, so change its type to s8.
>
> After that, "iw wlan0 station dump" show the correct ack signal strength.
>
> Such as:
> root@CDCCSTEX0799733-LIN:~# iw wlp88s0 station dump
> Station 00:03:7f:12:df:df (on wlp88s0)
> inactive time: 75 ms
> rx bytes: 11599
> rx packets: 99
> tx bytes: 9029
> tx packets: 81
> tx retries: 4
> tx failed: 0
> rx drop misc: 2
> signal: -16 dBm
> signal avg: -24 dBm
> tx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
> tx duration: 9230 us
> rx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
> rx duration: 7201 us
> last ack signal:-23 dBm
> avg ack signal: -22 dBm
>
> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
>
> Signed-off-by: Lingbo Kong <[email protected]>
> ---
> drivers/net/wireless/ath/ath11k/dp_tx.c | 16 ++++++++++++----
> drivers/net/wireless/ath/ath11k/dp_tx.h | 4 ++--
> drivers/net/wireless/ath/ath11k/hal_tx.h | 4 ++--
> 3 files changed, 16 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/net/wireless/ath/ath11k/dp_tx.c b/drivers/net/wireless/ath/ath11k/dp_tx.c
> index 21819b741701..8522c67baabf 100644
> --- a/drivers/net/wireless/ath/ath11k/dp_tx.c
> +++ b/drivers/net/wireless/ath/ath11k/dp_tx.c
> @@ -353,8 +353,12 @@ ath11k_dp_tx_htt_tx_complete_buf(struct ath11k_base *ab,
> if (ts->acked) {
> if (!(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
> info->flags |= IEEE80211_TX_STAT_ACK;
> - info->status.ack_signal = ATH11K_DEFAULT_NOISE_FLOOR +
> - ts->ack_rssi;
> + info->status.ack_signal = ts->ack_rssi;
> +
> + if (!test_bit(WMI_TLV_SERVICE_HW_DB2DBM_CONVERSION_SUPPORT,
> + ab->wmi_ab.svc_map))
> + info->status.ack_signal += ATH11K_DEFAULT_NOISE_FLOOR;
> +
> info->status.flags |=
> IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
> } else {
> @@ -584,8 +588,12 @@ static void ath11k_dp_tx_complete_msdu(struct ath11k *ar,
> if (ts->status == HAL_WBM_TQM_REL_REASON_FRAME_ACKED &&
> !(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
> info->flags |= IEEE80211_TX_STAT_ACK;
> - info->status.ack_signal = ATH11K_DEFAULT_NOISE_FLOOR +
> - ts->ack_rssi;
> + info->status.ack_signal = ts->ack_rssi;
> +
> + if (!test_bit(WMI_TLV_SERVICE_HW_DB2DBM_CONVERSION_SUPPORT,
> + ab->wmi_ab.svc_map))
> + info->status.ack_signal += ATH11K_DEFAULT_NOISE_FLOOR;
> +
> info->status.flags |= IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
> }
>
> diff --git a/drivers/net/wireless/ath/ath11k/dp_tx.h b/drivers/net/wireless/ath/ath11k/dp_tx.h
> index 61be2265e09f..795fe3b8fa0d 100644
> --- a/drivers/net/wireless/ath/ath11k/dp_tx.h
> +++ b/drivers/net/wireless/ath/ath11k/dp_tx.h
> @@ -1,7 +1,7 @@
> /* SPDX-License-Identifier: BSD-3-Clause-Clear */
> /*
> * Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
> - * Copyright (c) 2021, 2023 Qualcomm Innovation Center, Inc. All rights reserved.
> + * Copyright (c) 2021, 2023-2024 Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> #ifndef ATH11K_DP_TX_H
> @@ -13,7 +13,7 @@
> struct ath11k_dp_htt_wbm_tx_status {
> u32 msdu_id;
> bool acked;
> - int ack_rssi;
> + s8 ack_rssi;
> u16 peer_id;
> };
>
> diff --git a/drivers/net/wireless/ath/ath11k/hal_tx.h b/drivers/net/wireless/ath/ath11k/hal_tx.h
> index c5e88364afe5..46d17abd808b 100644
> --- a/drivers/net/wireless/ath/ath11k/hal_tx.h
> +++ b/drivers/net/wireless/ath/ath11k/hal_tx.h
> @@ -1,7 +1,7 @@
> /* SPDX-License-Identifier: BSD-3-Clause-Clear */
> /*
> * Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
> - * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
> + * Copyright (c) 2022, 2024 Qualcomm Innovation Center, Inc. All rights reserved.
> */
>
> #ifndef ATH11K_HAL_TX_H
> @@ -54,7 +54,7 @@ struct hal_tx_info {
> struct hal_tx_status {
> enum hal_wbm_rel_src_module buf_rel_source;
> enum hal_wbm_tqm_rel_reason status;
> - u8 ack_rssi;
> + s8 ack_rssi;
> u32 flags; /* %HAL_TX_STATUS_FLAGS_ */
> u32 ppdu_id;
> u8 try_cnt;
>
> base-commit: a116bf2be795eb1db75fa6a48aa85c397be001a6
On 2024/6/13 19:57, James Prestwood wrote:
> Hi Lingbo,
>
> On 6/10/24 7:25 PM, Lingbo Kong wrote:
>> Currently, the calculation of ack signal strength is incorrect.
>>
>> This is because before calculating the ack signal strength, ath11k need
>> to determine whether the hardware and firmware support db2dbm. If the
>> hardware and firmware support db2dbm, do not need to add noise floor,
>> otherwise, need to add noise floor.
>
> This oatch got me checking on some devices we have running ath11k
> (WCN6855). I don't see any "ack signal" property but I noticed the
> signal avg does not seem correct:
>
> signal: -55 [-62, -56] dBm
> signal avg: 105 dBm
>
> Every other device besides ath11k has a signal avg close to or equal to
> the signal. Do you think there is also an issue with this property? not
> just the ack signal?
>
> Thanks,
>
> James
>
Hi,james,
This is indeed a issue, but I have solved it. It's just that this patch
has not been applied to ath.git. you can apply the following patch.
https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/
best regards
Lingbo Kong
>>
>> Besides, the value of ack_rssi passed by firmware to ath11k should be a
>> signed number, so change its type to s8.
>>
>> After that, "iw wlan0 station dump" show the correct ack signal strength.
>>
>> Such as:
>> root@CDCCSTEX0799733-LIN:~# iw wlp88s0 station dump
>> Station 00:03:7f:12:df:df (on wlp88s0)
>> inactive time: 75 ms
>> rx bytes: 11599
>> rx packets: 99
>> tx bytes: 9029
>> tx packets: 81
>> tx retries: 4
>> tx failed: 0
>> rx drop misc: 2
>> signal: -16 dBm
>> signal avg: -24 dBm
>> tx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
>> tx duration: 9230 us
>> rx bitrate: 1560.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 4
>> rx duration: 7201 us
>> last ack signal:-23 dBm
>> avg ack signal: -22 dBm
>>
>> Tested-on: WCN6855 hw2.0 PCI
>> WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
>> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
>>
>> Signed-off-by: Lingbo Kong <[email protected]>
>> ---
>> drivers/net/wireless/ath/ath11k/dp_tx.c | 16 ++++++++++++----
>> drivers/net/wireless/ath/ath11k/dp_tx.h | 4 ++--
>> drivers/net/wireless/ath/ath11k/hal_tx.h | 4 ++--
>> 3 files changed, 16 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/net/wireless/ath/ath11k/dp_tx.c
>> b/drivers/net/wireless/ath/ath11k/dp_tx.c
>> index 21819b741701..8522c67baabf 100644
>> --- a/drivers/net/wireless/ath/ath11k/dp_tx.c
>> +++ b/drivers/net/wireless/ath/ath11k/dp_tx.c
>> @@ -353,8 +353,12 @@ ath11k_dp_tx_htt_tx_complete_buf(struct
>> ath11k_base *ab,
>> if (ts->acked) {
>> if (!(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
>> info->flags |= IEEE80211_TX_STAT_ACK;
>> - info->status.ack_signal = ATH11K_DEFAULT_NOISE_FLOOR +
>> - ts->ack_rssi;
>> + info->status.ack_signal = ts->ack_rssi;
>> +
>> + if (!test_bit(WMI_TLV_SERVICE_HW_DB2DBM_CONVERSION_SUPPORT,
>> + ab->wmi_ab.svc_map))
>> + info->status.ack_signal += ATH11K_DEFAULT_NOISE_FLOOR;
>> +
>> info->status.flags |=
>> IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
>> } else {
>> @@ -584,8 +588,12 @@ static void ath11k_dp_tx_complete_msdu(struct
>> ath11k *ar,
>> if (ts->status == HAL_WBM_TQM_REL_REASON_FRAME_ACKED &&
>> !(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
>> info->flags |= IEEE80211_TX_STAT_ACK;
>> - info->status.ack_signal = ATH11K_DEFAULT_NOISE_FLOOR +
>> - ts->ack_rssi;
>> + info->status.ack_signal = ts->ack_rssi;
>> +
>> + if (!test_bit(WMI_TLV_SERVICE_HW_DB2DBM_CONVERSION_SUPPORT,
>> + ab->wmi_ab.svc_map))
>> + info->status.ack_signal += ATH11K_DEFAULT_NOISE_FLOOR;
>> +
>> info->status.flags |= IEEE80211_TX_STATUS_ACK_SIGNAL_VALID;
>> }
>> diff --git a/drivers/net/wireless/ath/ath11k/dp_tx.h
>> b/drivers/net/wireless/ath/ath11k/dp_tx.h
>> index 61be2265e09f..795fe3b8fa0d 100644
>> --- a/drivers/net/wireless/ath/ath11k/dp_tx.h
>> +++ b/drivers/net/wireless/ath/ath11k/dp_tx.h
>> @@ -1,7 +1,7 @@
>> /* SPDX-License-Identifier: BSD-3-Clause-Clear */
>> /*
>> * Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
>> - * Copyright (c) 2021, 2023 Qualcomm Innovation Center, Inc. All
>> rights reserved.
>> + * Copyright (c) 2021, 2023-2024 Qualcomm Innovation Center, Inc. All
>> rights reserved.
>> */
>> #ifndef ATH11K_DP_TX_H
>> @@ -13,7 +13,7 @@
>> struct ath11k_dp_htt_wbm_tx_status {
>> u32 msdu_id;
>> bool acked;
>> - int ack_rssi;
>> + s8 ack_rssi;
>> u16 peer_id;
>> };
>> diff --git a/drivers/net/wireless/ath/ath11k/hal_tx.h
>> b/drivers/net/wireless/ath/ath11k/hal_tx.h
>> index c5e88364afe5..46d17abd808b 100644
>> --- a/drivers/net/wireless/ath/ath11k/hal_tx.h
>> +++ b/drivers/net/wireless/ath/ath11k/hal_tx.h
>> @@ -1,7 +1,7 @@
>> /* SPDX-License-Identifier: BSD-3-Clause-Clear */
>> /*
>> * Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
>> - * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights
>> reserved.
>> + * Copyright (c) 2022, 2024 Qualcomm Innovation Center, Inc. All
>> rights reserved.
>> */
>> #ifndef ATH11K_HAL_TX_H
>> @@ -54,7 +54,7 @@ struct hal_tx_info {
>> struct hal_tx_status {
>> enum hal_wbm_rel_src_module buf_rel_source;
>> enum hal_wbm_tqm_rel_reason status;
>> - u8 ack_rssi;
>> + s8 ack_rssi;
>> u32 flags; /* %HAL_TX_STATUS_FLAGS_ */
>> u32 ppdu_id;
>> u8 try_cnt;
>>
>> base-commit: a116bf2be795eb1db75fa6a48aa85c397be001a6