The accelerometer's power supply could be controlled by regulator
on some platforms, add optional property "vdd/vddio" power supply
to let device tree to pass phandles to the regulators to driver.
Signed-off-by: Anson Huang <[email protected]>
---
Documentation/devicetree/bindings/iio/accel/mma8452.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
index 2100e9a..e132394 100644
--- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt
+++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
@@ -20,6 +20,10 @@ Optional properties:
- interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's
interrupt line in use.
+ - vdd-supply: phandle to the regulator that provides vdd power to the accelerometer.
+
+ - vddio-supply: phandle to the regulator that provides vddio power to the accelerometer.
+
Example:
mma8453fc@1d {
--
2.7.4
The accelerometer's power supply could be controlled by regulator
on some platforms, such as i.MX6Q-SABRESD board, the mma8451's
power supply is controlled by a GPIO fixed regulator, need to make
sure the regulator is enabled before any communication with mma8451,
this patch adds optional vdd/vddio regulator operation support.
Signed-off-by: Anson Huang <[email protected]>
---
ChangeLog since V1:
- Add defer_probe check if the return value from devm_regulator_get_optional is ERR_PTR(-EPROBE_DEFER);
- Replace the "vcc" with "vdd" according to datasheet, and add optional "vddio" supply as well since
mma8452 also has a vddio supply.
---
drivers/iio/accel/mma8452.c | 151 +++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 149 insertions(+), 2 deletions(-)
diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index 421a0a8..18dcf33 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -31,6 +31,7 @@
#include <linux/of_device.h>
#include <linux/of_irq.h>
#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
#define MMA8452_STATUS 0x00
#define MMA8452_STATUS_DRDY (BIT(2) | BIT(1) | BIT(0))
@@ -107,6 +108,8 @@ struct mma8452_data {
u8 data_cfg;
const struct mma_chip_info *chip_info;
int sleep_val;
+ struct regulator *vdd_reg;
+ struct regulator *vddio_reg;
};
/**
@@ -1533,6 +1536,27 @@ static int mma8452_probe(struct i2c_client *client,
data->client = client;
mutex_init(&data->lock);
data->chip_info = match->data;
+ data->vdd_reg = devm_regulator_get_optional(&client->dev, "vdd");
+ if (!IS_ERR(data->vdd_reg)) {
+ ret = regulator_enable(data->vdd_reg);
+ if (ret) {
+ dev_err(&client->dev, "failed to enable VDD regulator\n");
+ return ret;
+ }
+ } else if (data->vdd_reg == ERR_PTR(-EPROBE_DEFER)) {
+ return -EPROBE_DEFER;
+ }
+
+ data->vddio_reg = devm_regulator_get_optional(&client->dev, "vddio");
+ if (!IS_ERR(data->vddio_reg)) {
+ ret = regulator_enable(data->vddio_reg);
+ if (ret) {
+ dev_err(&client->dev, "failed to enable VDDIO regulator\n");
+ return ret;
+ }
+ } else if (data->vddio_reg == ERR_PTR(-EPROBE_DEFER)) {
+ return -EPROBE_DEFER;
+ }
ret = i2c_smbus_read_byte_data(client, MMA8452_WHO_AM_I);
if (ret < 0)
@@ -1667,6 +1691,8 @@ static int mma8452_probe(struct i2c_client *client,
static int mma8452_remove(struct i2c_client *client)
{
struct iio_dev *indio_dev = i2c_get_clientdata(client);
+ struct mma8452_data *data = iio_priv(indio_dev);
+ int ret;
iio_device_unregister(indio_dev);
@@ -1678,6 +1704,21 @@ static int mma8452_remove(struct i2c_client *client)
mma8452_trigger_cleanup(indio_dev);
mma8452_standby(iio_priv(indio_dev));
+ if (!IS_ERR(data->vdd_reg)) {
+ ret = regulator_disable(data->vdd_reg);
+ if (ret) {
+ dev_err(&client->dev, "failed to disable VDD regulator\n");
+ return ret;
+ }
+ }
+ if (!IS_ERR(data->vddio_reg)) {
+ ret = regulator_disable(data->vddio_reg);
+ if (ret) {
+ dev_err(&client->dev, "failed to disable VDDIO regulator\n");
+ return ret;
+ }
+ }
+
return 0;
}
@@ -1696,6 +1737,21 @@ static int mma8452_runtime_suspend(struct device *dev)
return -EAGAIN;
}
+ if (!IS_ERR(data->vdd_reg)) {
+ ret = regulator_disable(data->vdd_reg);
+ if (ret) {
+ dev_err(dev, "failed to disable VDD regulator\n");
+ return ret;
+ }
+ }
+ if (!IS_ERR(data->vddio_reg)) {
+ ret = regulator_disable(data->vddio_reg);
+ if (ret) {
+ dev_err(dev, "failed to disable VDDIO regulator\n");
+ return ret;
+ }
+ }
+
return 0;
}
@@ -1705,6 +1761,21 @@ static int mma8452_runtime_resume(struct device *dev)
struct mma8452_data *data = iio_priv(indio_dev);
int ret, sleep_val;
+ if (!IS_ERR(data->vdd_reg)) {
+ ret = regulator_enable(data->vdd_reg);
+ if (ret) {
+ dev_err(dev, "failed to enable VDD regulator\n");
+ return ret;
+ }
+ }
+ if (!IS_ERR(data->vddio_reg)) {
+ ret = regulator_enable(data->vddio_reg);
+ if (ret) {
+ dev_err(dev, "failed to enable VDDIO regulator\n");
+ return ret;
+ }
+ }
+
ret = mma8452_active(data);
if (ret < 0)
return ret;
@@ -1723,14 +1794,90 @@ static int mma8452_runtime_resume(struct device *dev)
#ifdef CONFIG_PM_SLEEP
static int mma8452_suspend(struct device *dev)
{
- return mma8452_standby(iio_priv(i2c_get_clientdata(
+ struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
+ struct mma8452_data *data = iio_priv(indio_dev);
+ int ret;
+
+ if (!IS_ERR(data->vdd_reg)) {
+ ret = regulator_enable(data->vdd_reg);
+ if (ret) {
+ dev_err(dev, "failed to enable VDD regulator\n");
+ return ret;
+ }
+ }
+ if (!IS_ERR(data->vddio_reg)) {
+ ret = regulator_enable(data->vddio_reg);
+ if (ret) {
+ dev_err(dev, "failed to enable VDDIO regulator\n");
+ return ret;
+ }
+ }
+
+ ret = mma8452_standby(iio_priv(i2c_get_clientdata(
to_i2c_client(dev))));
+ if (ret)
+ return ret;
+
+ if (!IS_ERR(data->vdd_reg)) {
+ ret = regulator_disable(data->vdd_reg);
+ if (ret) {
+ dev_err(dev, "failed to disable VDD regulator\n");
+ return ret;
+ }
+ }
+ if (!IS_ERR(data->vddio_reg)) {
+ ret = regulator_disable(data->vddio_reg);
+ if (ret) {
+ dev_err(dev, "failed to disable VDDIO regulator\n");
+ return ret;
+ }
+ }
+
+ return 0;
}
static int mma8452_resume(struct device *dev)
{
- return mma8452_active(iio_priv(i2c_get_clientdata(
+ struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
+ struct mma8452_data *data = iio_priv(indio_dev);
+ int ret;
+
+ if (!IS_ERR(data->vdd_reg)) {
+ ret = regulator_enable(data->vdd_reg);
+ if (ret) {
+ dev_err(dev, "failed to enable VDD regulator\n");
+ return ret;
+ }
+ }
+ if (!IS_ERR(data->vddio_reg)) {
+ ret = regulator_enable(data->vddio_reg);
+ if (ret) {
+ dev_err(dev, "failed to enable VDDIO regulator\n");
+ return ret;
+ }
+ }
+
+ ret = mma8452_active(iio_priv(i2c_get_clientdata(
to_i2c_client(dev))));
+ if (ret)
+ return ret;
+
+ if (!IS_ERR(data->vdd_reg)) {
+ ret = regulator_disable(data->vdd_reg);
+ if (ret) {
+ dev_err(dev, "failed to disable VDD regulator\n");
+ return ret;
+ }
+ }
+ if (!IS_ERR(data->vddio_reg)) {
+ ret = regulator_disable(data->vddio_reg);
+ if (ret) {
+ dev_err(dev, "failed to disable VDDIO regulator\n");
+ return ret;
+ }
+ }
+
+ return 0;
}
#endif
--
2.7.4
On 10.12.18 08:25, Anson Huang wrote:
> The accelerometer's power supply could be controlled by regulator
> on some platforms, such as i.MX6Q-SABRESD board, the mma8451's
> power supply is controlled by a GPIO fixed regulator, need to make
> sure the regulator is enabled before any communication with mma8451,
> this patch adds optional vdd/vddio regulator operation support.
>
> Signed-off-by: Anson Huang <[email protected]>
Acked-by: Martin Kepplinger <[email protected]>
On Mon, Dec 10, 2018 at 5:25 AM Anson Huang <[email protected]> wrote:
> @@ -1533,6 +1536,27 @@ static int mma8452_probe(struct i2c_client *client,
> data->client = client;
> mutex_init(&data->lock);
> data->chip_info = match->data;
> + data->vdd_reg = devm_regulator_get_optional(&client->dev, "vdd");
> + if (!IS_ERR(data->vdd_reg)) {
> + ret = regulator_enable(data->vdd_reg);
> + if (ret) {
> + dev_err(&client->dev, "failed to enable VDD regulator\n");
> + return ret;
> + }
> + } else if (data->vdd_reg == ERR_PTR(-EPROBE_DEFER)) {
> + return -EPROBE_DEFER;
> + }
> +
> + data->vddio_reg = devm_regulator_get_optional(&client->dev, "vddio");
> + if (!IS_ERR(data->vddio_reg)) {
> + ret = regulator_enable(data->vddio_reg);
> + if (ret) {
> + dev_err(&client->dev, "failed to enable VDDIO regulator\n");
> + return ret;
As mentioned in your other patch: you should disable the previously
enabled regulator in the error path.