From: Xilin Wu <[email protected]>
AYN Odin 2 is a gaming handheld based on QCS8550, which is derived
from SM8550 but without modem RF system.
This commit brings support for:
* Remoteprocs
* UFS storage
* SD Card
* Type-C with USB3 10Gbps and DisplayPort (4-lane requires a pending
patch)
* PCIe0 (Wi-Fi requires the pending pwrseq series)
* Bluetooth
* Regulators
* Integrated fan with automatic speed control based on CPU temperature
* Power and volume keys
* M1, M2 buttons
* HDMI output up to 1080p 60hz
* four groups of RGB lights
* GPU
* Internal DSI display with touchscreen
Signed-off-by: Xilin Wu <[email protected]>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/qcs8550-ayn-odin2.dts | 1410 ++++++++++++++++++++++++
2 files changed, 1411 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index c46c10d85697..070c0d996059 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -97,6 +97,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qcs8550-ayn-odin2.dtb
dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb2210-rb1.dtb
dtb-$(CONFIG_ARCH_QCOM) += qrb4210-rb2.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayn-odin2.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayn-odin2.dts
new file mode 100644
index 000000000000..bfe353d3c53e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-ayn-odin2.dts
@@ -0,0 +1,1410 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Xilin Wu <[email protected]>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/arm/qcom,ids.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcs8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550b.dtsi"
+#define PMK8550VE_SID 5
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/*
+ * The SoC being used on this product doesn't feature modem
+ * and camera subsystem.
+ * Variant: 202-AB
+ * FEATURE_ID: 0x8
+ */
+
+/delete-node/ &mpss_mem;
+/delete-node/ &q6_mpss_dtb_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &camera_mem;
+/delete-node/ &mpss_dsm_mem;
+/delete-node/ &camcc;
+/delete-node/ &remoteproc_mpss;
+
+/ {
+ model = "AYN Odin 2";
+ compatible = "ayn,odin2", "qcom,qcs8550", "qcom,sm8550";
+ chassis-type = "handset";
+
+ qcom,msm-id = <QCOM_ID_QCS8550 0x20000>;
+ qcom,board-id = <0x1001f 0>;
+
+ aliases {
+ serial0 = &uart7;
+ serial1 = &uart14;
+ serial2 = &uart15;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pmk8550_pwm 0 860000>;
+ brightness-levels = <1023 0>;
+ num-interpolated-steps = <1023>;
+ default-brightness-level = <600>;
+ power-supply = <&vph_pwr>;
+ enable-gpios = <&pmk8550_gpios 5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_backlight_default>;
+ status = "okay";
+ };
+
+ fan_pwr: fan-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "fan_pwr";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&fan_pwr_en>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&volume_up_n>, <&m1_m2_keys_default>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+
+ m1-button {
+ label = "M1";
+ linux,code = <BTN_TRIGGER_HAPPY1>;
+ gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+ };
+
+ m2-button {
+ label = "M2";
+ linux,code = <BTN_TRIGGER_HAPPY2>;
+ gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "d";
+ hpd-gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <<8912_out>;
+ };
+ };
+ };
+
+ hdmi_pwr: hdmi-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "hdmi_pwr";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 10 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vdd_lcm_2p8: vdd-lcm-2p8-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_lcm_2p8";
+
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ gpio = <&tlmm 142 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ led_left_side: led-controller-1 {
+ compatible = "pwm-leds-multicolor";
+
+ multi-led {
+ label = "left-side";
+ color = <LED_COLOR_ID_RGB>;
+ max-brightness = <255>;
+
+ led-red {
+ color = <LED_COLOR_ID_RED>;
+ pwms = <&pwm_rgb_left 0>;
+ };
+
+ led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ pwms = <&pwm_rgb_left 1>;
+ };
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ pwms = <&pwm_rgb_left 2>;
+ };
+ };
+ };
+
+ led_left_joystick: led-controller-2 {
+ compatible = "pwm-leds-multicolor";
+
+ multi-led {
+ label = "left-joystick";
+ color = <LED_COLOR_ID_RGB>;
+ max-brightness = <255>;
+
+ led-red {
+ color = <LED_COLOR_ID_RED>;
+ pwms = <&pwm_rgb_left 6>;
+ };
+
+ led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ pwms = <&pwm_rgb_left 7>;
+ };
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ pwms = <&pwm_rgb_left 8>;
+ };
+ };
+ };
+
+ led_right_side: led-controller-3 {
+ compatible = "pwm-leds-multicolor";
+
+ multi-led {
+ label = "right-side";
+ color = <LED_COLOR_ID_RGB>;
+ max-brightness = <255>;
+
+ led-red {
+ color = <LED_COLOR_ID_RED>;
+ pwms = <&pwm_rgb_right 0>;
+ };
+
+ led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ pwms = <&pwm_rgb_right 1>;
+ };
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ pwms = <&pwm_rgb_right 2>;
+ };
+ };
+ };
+
+ led_right_joystick: led-controller-4 {
+ compatible = "pwm-leds-multicolor";
+
+ multi-led {
+ label = "right-joystick";
+ color = <LED_COLOR_ID_RGB>;
+ max-brightness = <255>;
+
+ led-red {
+ color = <LED_COLOR_ID_RED>;
+ pwms = <&pwm_rgb_right 6>;
+ };
+
+ led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ pwms = <&pwm_rgb_right 7>;
+ };
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ pwms = <&pwm_rgb_right 8>;
+ };
+ };
+ };
+
+ mcu_3v3: mcu-3v3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "mcu_3v3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ regulator-boot-on;
+ enable-active-high;
+ };
+
+ pmic-glink {
+ compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_dp_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_sbu: endpoint {
+ remote-endpoint = <&usb0_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
+ fan: pwm-fan {
+ compatible = "pwm-fan";
+ cooling-levels = <0 40 65 75 90 100 120 150>;
+ #cooling-cells = <2>;
+ fan-supply = <&fan_pwr>;
+ pwms = <&pm8550_pwm 3 100000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_out_default &fan_int>;
+
+ pulses-per-revolution = <4>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+ };
+
+ thermal-zones {
+ cpuss0-thermal {
+ trips {
+ cpuss0_active0: trip-point2 {
+ temperature = <50000>;
+ hysteresis = <4000>;
+ type = "active";
+ };
+
+ cpuss0_active1: trip-point3 {
+ temperature = <55000>;
+ hysteresis = <4000>;
+ type = "active";
+ };
+
+ cpuss0_active2: trip-point4 {
+ temperature = <60000>;
+ hysteresis = <4000>;
+ type = "active";
+ };
+
+ cpuss0_active3: trip-point5 {
+ temperature = <65000>;
+ hysteresis = <4000>;
+ type = "active";
+ };
+
+ cpuss0_active4: trip-point6 {
+ temperature = <70000>;
+ hysteresis = <4000>;
+ type = "active";
+ };
+
+ cpuss0_active5: trip-point7 {
+ temperature = <75000>;
+ hysteresis = <4000>;
+ type = "active";
+ };
+
+ cpuss0_active6: trip-point8 {
+ temperature = <80000>;
+ hysteresis = <4000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpuss0_active0>;
+ cooling-device = <&fan 0 1>;
+ };
+ map1 {
+ trip = <&cpuss0_active1>;
+ cooling-device = <&fan 1 2>;
+ };
+ map2 {
+ trip = <&cpuss0_active2>;
+ cooling-device = <&fan 2 3>;
+ };
+ map3 {
+ trip = <&cpuss0_active3>;
+ cooling-device = <&fan 3 4>;
+ };
+ map4 {
+ trip = <&cpuss0_active4>;
+ cooling-device = <&fan 4 5>;
+ };
+ map5 {
+ trip = <&cpuss0_active5>;
+ cooling-device = <&fan 5 6>;
+ };
+ map6 {
+ trip = <&cpuss0_active6>;
+ cooling-device = <&fan 6 7>;
+ };
+ };
+ };
+ };
+
+ usb0-sbu-mux {
+ compatible = "pericom,pi3usb102", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 140 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 141 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_sbu_default>;
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usb0_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_sbu>;
+ };
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-bob1-supply = <&vph_pwr>;
+ vdd-bob2-supply = <&vph_pwr>;
+ vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
+ vdd-l2-l13-l14-supply = <&vreg_bob1>;
+ vdd-l3-supply = <&vreg_s4g_1p25>;
+ vdd-l5-l16-supply = <&vreg_bob1>;
+ vdd-l6-l7-supply = <&vreg_bob1>;
+ vdd-l8-l9-supply = <&vreg_bob1>;
+ vdd-l11-supply = <&vreg_s4g_1p25>;
+ vdd-l12-supply = <&vreg_s6g_1p86>;
+ vdd-l15-supply = <&vreg_s6g_1p86>;
+ vdd-l17-supply = <&vreg_bob2>;
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2720000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1b_1p8: ldo1 {
+ regulator-name = "vreg_l1b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_3p1: ldo5 {
+ regulator-name = "vreg_l5b_3p1";
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_1p8: ldo7 {
+ regulator-name = "vreg_l7b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_1p8: ldo8 {
+ regulator-name = "vreg_l8b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10b_1p8: ldo10 {
+ regulator-name = "vreg_l10b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11b_1p2: ldo11 {
+ regulator-name = "vreg_l11b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p8: ldo12 {
+ regulator-name = "vreg_l12b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p2: ldo14 {
+ regulator-name = "vreg_l14b_3p2";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16b_2p8: ldo16 {
+ regulator-name = "vreg_l16b_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* Setting regulator-allow-set-load here will crash the device */
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-l1-supply = <&vreg_s4g_1p25>;
+ vdd-l2-supply = <&vreg_s4e_0p95>;
+ vdd-l3-supply = <&vreg_s4e_0p95>;
+
+ vreg_l1c_1p2: ldo1 {
+ regulator-name = "vreg_l1c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_0p9: ldo3 {
+ regulator-name = "vreg_l3c_0p9";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vdd-l1-supply = <&vreg_s4e_0p95>;
+ vdd-l2-supply = <&vreg_s4e_0p95>;
+ vdd-l3-supply = <&vreg_s4e_0p95>;
+
+ vreg_l1d_0p88: ldo1 {
+ regulator-name = "vreg_l1d_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* ldo2 supplies SM8550 VDD_LPI_MX */
+ };
+
+ regulators-3 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vdd-l1-supply = <&vreg_s4e_0p95>;
+ vdd-l2-supply = <&vreg_s4e_0p95>;
+ vdd-l3-supply = <&vreg_s4g_1p25>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+
+ vreg_s4e_0p95: smps4 {
+ regulator-name = "vreg_s4e_0p95";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <984000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5e_1p08: smps5 {
+ regulator-name = "vreg_s5e_1p08";
+ regulator-min-microvolt = <1010000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1e_0p88: ldo1 {
+ regulator-name = "vreg_l1e_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2e_0p9: ldo2 {
+ regulator-name = "vreg_l2e_0p9";
+ regulator-min-microvolt = <870000>;
+ regulator-max-microvolt = <970000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3e_1p2: ldo3 {
+ regulator-name = "vreg_l3e_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vdd-l1-supply = <&vreg_s4e_0p95>;
+ vdd-l2-supply = <&vreg_s4e_0p95>;
+ vdd-l3-supply = <&vreg_s4e_0p95>;
+ vdd-s4-supply = <&vph_pwr>;
+
+ vreg_s4f_0p5: smps4 {
+ regulator-name = "vreg_s4f_0p5";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <700000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1f_0p9: ldo1 {
+ regulator-name = "vreg_l1f_0p9";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2f_0p88: ldo2 {
+ regulator-name = "vreg_l2f_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3f_0p88: ldo3 {
+ regulator-name = "vreg_l3f_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-5 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "g";
+
+ vdd-l1-supply = <&vreg_s4g_1p25>;
+ vdd-l2-supply = <&vreg_s4g_1p25>;
+ vdd-l3-supply = <&vreg_s4g_1p25>;
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+
+ vreg_s1g_1p25: smps1 {
+ regulator-name = "vreg_s1g_1p25";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2g_0p85: smps2 {
+ regulator-name = "vreg_s2g_0p85";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1036000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s3g_0p8: smps3 {
+ regulator-name = "vreg_s3g_0p8";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4g_1p25: smps4 {
+ regulator-name = "vreg_s4g_1p25";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1352000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>;
+ };
+
+ vreg_s5g_0p85: smps5 {
+ regulator-name = "vreg_s5g_0p85";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6g_1p86: smps6 {
+ regulator-name = "vreg_s6g_1p86";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1g_1p2: ldo1 {
+ regulator-name = "vreg_l1g_1p2";
+ regulator-min-microvolt = <1144000>;
+ regulator-max-microvolt = <1256000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2g_1p1: ldo2 {
+ regulator-name = "vreg_l2g_1p1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3g_1p2: ldo3 {
+ regulator-name = "vreg_l3g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&gpi_dma2 {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+
+ zap-shader {
+ firmware-name = "qcom/sm8550/ayn/odin2/a740_zap.mbn";
+ };
+};
+
+&hub_i2c0_data_clk {
+ /delete-property/ bias-pull-up;
+ bias-disable;
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ pwm_rgb_left: pwm@54 {
+ compatible = "si-en,sn3112-pwm";
+ reg = <0x54>;
+ sdb-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&mcu_3v3>;
+ #pwm-cells = <1>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts-extended = <&tlmm 25 0x2008>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&ts_int_default>;
+ pinctrl-1 = <&ts_int_sleep>;
+
+ vio-supply = <&vreg_l12b_1p8>;
+
+ syna,startup-delay-ms = <200>;
+ syna,reset-delay-ms = <200>;
+
+ rmi4-f01@1 {
+ syna,nosleep-mode = <0x1>;
+ reg = <0x1>;
+ };
+
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,rezero-wait-ms = <20>;
+ syna,clip-x-low = <0>;
+ syna,clip-y-low = <0>;
+ syna,clip-x-high = <1080>;
+ syna,clip-y-high = <1920>;
+ syna,sensor-type = <1>;
+ touchscreen-inverted-x;
+ };
+ };
+};
+
+&i2c12 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ pwm_rgb_right: pwm@54 {
+ compatible = "si-en,sn3112-pwm";
+ reg = <0x54>;
+ sdb-gpios = <&tlmm 56 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&mcu_3v3>;
+ #pwm-cells = <1>;
+ };
+};
+
+&i2c_master_hub_0 {
+ status = "okay";
+};
+
+&i2c_hub_0 {
+ clock-frequency = <100000>;
+ status = "okay";
+
+ hdmi-bridge@48 {
+ compatible = "lontium,lt8912b";
+ reg = <0x48> ;
+ reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+ vdd-supply = <&hdmi_pwr>;
+ vccmipirx-supply = <&hdmi_pwr>;
+ vccsysclk-supply = <&hdmi_pwr>;
+ vcclvdstx-supply = <&hdmi_pwr>;
+ vcchdmitx-supply = <&hdmi_pwr>;
+ vcclvdspll-supply = <&hdmi_pwr>;
+ vcchdmipll-supply = <&hdmi_pwr>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_out_in: endpoint {
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ lt8912_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+};
+
+&i2c_hub_2 {
+ status = "okay";
+
+ /* Awinic AW88166 audio amplifier @ 34, 35 */
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dsi0 {
+ vdda-supply = <&vreg_l3e_1p2>;
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ remote-endpoint = <&hdmi_out_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+ vdds-supply = <&vreg_l1e_0p88>;
+ status = "okay";
+};
+
+&mdss_dsi1 {
+ vdda-supply = <&vreg_l3e_1p2>;
+ status = "okay";
+
+ panel: panel@0 {
+ compatible = "syna,td4328";
+ reg = <0>;
+
+ pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>;
+ pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>;
+ pinctrl-names = "default", "sleep";
+
+ vdd-supply = <&vdd_lcm_2p8>;
+ vddio-supply = <&vreg_l12b_1p8>;
+
+ backlight = <&backlight>;
+ /* touchscreen and display panel share the same reset gpio! */
+ reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+ port {
+ panel0_in: endpoint {
+ remote-endpoint = <&mdss_dsi1_out>;
+ };
+ };
+ };
+};
+
+&mdss_dsi1_out {
+ remote-endpoint = <&panel0_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi1_phy {
+ vdds-supply = <&vreg_l1e_0p88>;
+ status = "okay";
+};
+
+&pcie0 {
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+ max-link-speed = <2>;
+
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l1e_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&pm8550_gpios {
+ pwm_out_default: pwm-out-default-state {
+ pins = "gpio8";
+ function = "func1";
+ input-disable;
+ output-enable;
+ output-low;
+ bias-disable;
+ power-source = <1>;
+ };
+
+ sdc2_card_det_n: sdc2-card-det-state {
+ pins = "gpio12";
+ function = "normal";
+ input-enable;
+ output-disable;
+ bias-pull-up;
+ power-source = <1>; /* 1.8 V */
+ };
+
+ volume_up_n: volume-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ power-source = <1>;
+ bias-pull-up;
+ input-enable;
+ };
+};
+
+&pm8550_pwm {
+ status = "okay";
+
+ multi-led {
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_CHARGING;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ led@3 {
+ reg = <3>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+ };
+};
+
+&pm8550b_eusb2_repeater {
+ qcom,tune-usb2-disc-thres = /bits/ 8 <0x6>;
+ qcom,tune-usb2-amplitude = /bits/ 8 <0xb>;
+ qcom,tune-usb2-preem = /bits/ 8 <0x3>;
+ vdd18-supply = <&vreg_l15b_1p8>;
+ vdd3-supply = <&vreg_l5b_3p1>;
+};
+
+&pmk8550_gpios {
+ pwm_backlight_default: pwm-backlight-default-state {
+ pins = "gpio5";
+ function = "func3";
+ input-disable;
+ output-enable;
+ output-low;
+ bias-disable;
+ power-source = <0>;
+ qcom,drive-strength = <2>;
+ };
+};
+
+&pmk8550_pwm {
+ status = "okay";
+};
+
+&pmk8550_rtc {
+ nvmem-cells = <&rtc_offset>;
+ nvmem-cell-names = "offset";
+
+ status = "okay";
+};
+
+&pmk8550_sdam_2 {
+ status = "okay";
+
+ rtc_offset: rtc-offset@bc {
+ reg = <0xbc 0x4>;
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sm8550/ayn/odin2/adsp.mbn",
+ "qcom/sm8550/ayn/odin2/adsp_dtb.mbn";
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/sm8550/ayn/odin2/cdsp.mbn",
+ "qcom/sm8550/ayn/odin2/cdsp_dtb.mbn";
+ status = "okay";
+};
+
+&sdhc_2 {
+ cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+ pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+ vmmc-supply = <&vreg_l9b_2p9>;
+ vqmmc-supply = <&vreg_l8b_1p8>;
+ bus-width = <4>;
+ no-sdio;
+ no-mmc;
+
+ /* SDR104 does seem to be working on this device*/
+ /delete-property/ sdhci-caps-mask;
+ qcom,dll-config = <0x0007442c>;
+
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32000>;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <32 8>;
+
+ fan_int: fan-int-state {
+ pins = "gpio13";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ fan_pwr_en: fan-pwr-en-state {
+ pins = "gpio109";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ m1_m2_keys_default: m1-m2-keys-default-state {
+ pins = "gpio57", "gpio58";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ ts_int_default: ts-int-default-state {
+ pins = "gpio25";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ ts_int_sleep: ts-int-sleep-state {
+ pins = "gpio25";
+ function = "gpio";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+
+ bt_default: bt-default-state {
+ bt-en-pins {
+ pins = "gpio81";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ sw-ctrl-pins {
+ pins = "gpio82";
+ function = "gpio";
+ bias-pull-down;
+ };
+ };
+
+ usb0_sbu_default: usb0-sbu-state {
+ oe-n-pins {
+ pins = "gpio140";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ output-high;
+ };
+
+ sel-pins {
+ pins = "gpio141";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ };
+ };
+
+ sde_dsi_active: sde-dsi-active-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ sde_dsi_suspend: sde-dsi-suspend-state {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ sde_te_active: sde-te-active-state {
+ pins = "gpio86";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ sde_te_suspend: sde-te-suspend-state {
+ pins = "gpio86";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+};
+
+&uart7 {
+ status = "okay";
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+
+ vddio-supply = <&vreg_l15b_1p8>;
+ vddaon-supply = <&vreg_s4e_0p95>;
+ vdddig-supply = <&vreg_s4e_0p95>;
+ vddrfa0p8-supply = <&vreg_s4e_0p95>;
+ vddrfa1p2-supply = <&vreg_s4g_1p25>;
+ vddrfa1p9-supply = <&vreg_s6g_1p86>;
+
+ max-speed = <3200000>;
+
+ enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+ swctrl-gpios = <&tlmm 82 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&bt_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&uart15 {
+ status = "okay";
+
+ /* Gamepad controlled by onboard MCU */
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l17b_2p5>;
+ vcc-max-microamp = <1300000>;
+ vccq-supply = <&vreg_l1g_1p2>;
+ vccq-max-microamp = <1200000>;
+ vdd-hba-supply = <&vreg_l3g_1p2>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l1d_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+ maximum-speed = "super-speed-plus-gen2x1";
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+ remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l1e_0p88>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ phys = <&pm8550b_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy {
+ vdda-phy-supply = <&vreg_l3e_1p2>;
+ vdda-pll-supply = <&vreg_l3f_0p88>;
+
+ orientation-switch;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy_dp_in {
+ remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_dp_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+ remote-endpoint = <&usb_1_dwc3_ss>;
+};
+
+&xo_board {
+ clock-frequency = <76800000>;
+};
--
2.44.0
On 24/04/2024 17:29, Xilin Wu via B4 Relay wrote:
> From: Xilin Wu <[email protected]>
>
> AYN Odin 2 is a gaming handheld based on QCS8550, which is derived
> from SM8550 but without modem RF system.
>
> +
> +/ {
> + model = "AYN Odin 2";
> + compatible = "ayn,odin2", "qcom,qcs8550", "qcom,sm8550";
> + chassis-type = "handset";
> +
> + qcom,msm-id = <QCOM_ID_QCS8550 0x20000>;
> + qcom,board-id = <0x1001f 0>;
No, these are not allowed. You did not test your dts.
It does not look like you tested the DTS against bindings. Please run
`make dtbs_check W=1` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).
> +
> + aliases {
> + serial0 = &uart7;
> + serial1 = &uart14;
> + serial2 = &uart15;
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pmk8550_pwm 0 860000>;
> + brightness-levels = <1023 0>;
> + num-interpolated-steps = <1023>;
> + default-brightness-level = <600>;
> + power-supply = <&vph_pwr>;
> + enable-gpios = <&pmk8550_gpios 5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm_backlight_default>;
> + status = "okay";
Drop, why do you need it? Do you see it anywhere else in the backlight
nodes in DTS?
> + };
> +
> + fan_pwr: fan-pwr-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "fan_pwr";
> +
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +
> + gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&fan_pwr_en>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + pinctrl-0 = <&volume_up_n>, <&m1_m2_keys_default>;
> + pinctrl-names = "default";
> +
> + key-volume-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
> + debounce-interval = <15>;
> + linux,can-disable;
> + wakeup-source;
> + };
> +
> + m1-button {
> + label = "M1";
> + linux,code = <BTN_TRIGGER_HAPPY1>;
> + gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
> + };
> +
> + m2-button {
> + label = "M2";
> + linux,code = <BTN_TRIGGER_HAPPY2>;
> + gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + hdmi-out {
> + compatible = "hdmi-connector";
> + type = "d";
> + hpd-gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
> +
> + port {
> + hdmi_con: endpoint {
> + remote-endpoint = <<8912_out>;
> + };
> + };
> + };
> +
> + hdmi_pwr: hdmi-pwr-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "hdmi_pwr";
> +
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + gpio = <&tlmm 10 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + vdd_lcm_2p8: vdd-lcm-2p8-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_lcm_2p8";
> +
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> +
> + gpio = <&tlmm 142 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + led_left_side: led-controller-1 {
> + compatible = "pwm-leds-multicolor";
> +
> + multi-led {
> + label = "left-side";
> + color = <LED_COLOR_ID_RGB>;
> + max-brightness = <255>;
> +
> + led-red {
> + color = <LED_COLOR_ID_RED>;
> + pwms = <&pwm_rgb_left 0>;
> + };
> +
> + led-green {
> + color = <LED_COLOR_ID_GREEN>;
> + pwms = <&pwm_rgb_left 1>;
> + };
> +
> + led-blue {
> + color = <LED_COLOR_ID_BLUE>;
> + pwms = <&pwm_rgb_left 2>;
> + };
> + };
> + };
> +
> + led_left_joystick: led-controller-2 {
> + compatible = "pwm-leds-multicolor";
> +
> + multi-led {
> + label = "left-joystick";
> + color = <LED_COLOR_ID_RGB>;
> + max-brightness = <255>;
> +
> + led-red {
> + color = <LED_COLOR_ID_RED>;
> + pwms = <&pwm_rgb_left 6>;
> + };
> +
> + led-green {
> + color = <LED_COLOR_ID_GREEN>;
> + pwms = <&pwm_rgb_left 7>;
> + };
> +
> + led-blue {
> + color = <LED_COLOR_ID_BLUE>;
> + pwms = <&pwm_rgb_left 8>;
> + };
> + };
> + };
> +
> + led_right_side: led-controller-3 {
> + compatible = "pwm-leds-multicolor";
> +
> + multi-led {
> + label = "right-side";
> + color = <LED_COLOR_ID_RGB>;
> + max-brightness = <255>;
> +
> + led-red {
> + color = <LED_COLOR_ID_RED>;
> + pwms = <&pwm_rgb_right 0>;
> + };
> +
> + led-green {
> + color = <LED_COLOR_ID_GREEN>;
> + pwms = <&pwm_rgb_right 1>;
> + };
> +
> + led-blue {
> + color = <LED_COLOR_ID_BLUE>;
> + pwms = <&pwm_rgb_right 2>;
> + };
> + };
> + };
> +
> + led_right_joystick: led-controller-4 {
> + compatible = "pwm-leds-multicolor";
> +
> + multi-led {
> + label = "right-joystick";
> + color = <LED_COLOR_ID_RGB>;
> + max-brightness = <255>;
> +
> + led-red {
> + color = <LED_COLOR_ID_RED>;
> + pwms = <&pwm_rgb_right 6>;
> + };
> +
> + led-green {
> + color = <LED_COLOR_ID_GREEN>;
> + pwms = <&pwm_rgb_right 7>;
> + };
> +
> + led-blue {
> + color = <LED_COLOR_ID_BLUE>;
> + pwms = <&pwm_rgb_right 8>;
> + };
> + };
> + };
> +
> + mcu_3v3: mcu-3v3-regulator {
Name all regulators regulator-n, where n is decimal number. Then order
the nodes by name.
..
> +
> +&i2c4 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + touchscreen@20 {
> + compatible = "syna,rmi4-i2c";
> + reg = <0x20>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interrupts-extended = <&tlmm 25 0x2008>;
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&ts_int_default>;
> + pinctrl-1 = <&ts_int_sleep>;
> +
> + vio-supply = <&vreg_l12b_1p8>;
> +
> + syna,startup-delay-ms = <200>;
> + syna,reset-delay-ms = <200>;
> +
> + rmi4-f01@1 {
> + syna,nosleep-mode = <0x1>;
> + reg = <0x1>;
> + };
> +
> + rmi4-f12@12 {
> + reg = <0x12>;
> + syna,rezero-wait-ms = <20>;
> + syna,clip-x-low = <0>;
> + syna,clip-y-low = <0>;
> + syna,clip-x-high = <1080>;
> + syna,clip-y-high = <1920>;
> + syna,sensor-type = <1>;
> + touchscreen-inverted-x;
> + };
> + };
Please confirm the status of dtbs_check for your board. I am pretty sure
it fails.
Best regards,
Krzysztof
On 2024/4/25 14:28, Krzysztof Kozlowski wrote:
> On 24/04/2024 17:29, Xilin Wu via B4 Relay wrote:
>> From: Xilin Wu <[email protected]>
>>
>> AYN Odin 2 is a gaming handheld based on QCS8550, which is derived
>> from SM8550 but without modem RF system.
>>
>
>
>
>> +
>> +/ {
>> + model = "AYN Odin 2";
>> + compatible = "ayn,odin2", "qcom,qcs8550", "qcom,sm8550";
>> + chassis-type = "handset";
>> +
>> + qcom,msm-id = <QCOM_ID_QCS8550 0x20000>;
>> + qcom,board-id = <0x1001f 0>;
>
> No, these are not allowed. You did not test your dts.
>
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check W=1` (see
> Documentation/devicetree/bindings/writing-schema.rst or
> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
> for instructions).
>
>> +
>> + aliases {
>> + serial0 = &uart7;
>> + serial1 = &uart14;
>> + serial2 = &uart15;
>> + };
>> +
>> + backlight: backlight {
>> + compatible = "pwm-backlight";
>> + pwms = <&pmk8550_pwm 0 860000>;
>> + brightness-levels = <1023 0>;
>> + num-interpolated-steps = <1023>;
>> + default-brightness-level = <600>;
>> + power-supply = <&vph_pwr>;
>> + enable-gpios = <&pmk8550_gpios 5 GPIO_ACTIVE_HIGH>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pwm_backlight_default>;
>> + status = "okay";
>
> Drop, why do you need it? Do you see it anywhere else in the backlight
> nodes in DTS?
>
>
>> + };
>> +
>> + fan_pwr: fan-pwr-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "fan_pwr";
>> +
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> +
>> + gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> +
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&fan_pwr_en>;
>> +
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> +
>> + pinctrl-0 = <&volume_up_n>, <&m1_m2_keys_default>;
>> + pinctrl-names = "default";
>> +
>> + key-volume-up {
>> + label = "Volume Up";
>> + linux,code = <KEY_VOLUMEUP>;
>> + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
>> + debounce-interval = <15>;
>> + linux,can-disable;
>> + wakeup-source;
>> + };
>> +
>> + m1-button {
>> + label = "M1";
>> + linux,code = <BTN_TRIGGER_HAPPY1>;
>> + gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + m2-button {
>> + label = "M2";
>> + linux,code = <BTN_TRIGGER_HAPPY2>;
>> + gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +
>> + hdmi-out {
>> + compatible = "hdmi-connector";
>> + type = "d";
>> + hpd-gpios = <&tlmm 9 GPIO_ACTIVE_HIGH>;
>> +
>> + port {
>> + hdmi_con: endpoint {
>> + remote-endpoint = <<8912_out>;
>> + };
>> + };
>> + };
>> +
>> + hdmi_pwr: hdmi-pwr-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "hdmi_pwr";
>> +
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> +
>> + gpio = <&tlmm 10 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + };
>> +
>> + vdd_lcm_2p8: vdd-lcm-2p8-regulator {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vdd_lcm_2p8";
>> +
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <2800000>;
>> +
>> + gpio = <&tlmm 142 GPIO_ACTIVE_HIGH>;
>> + enable-active-high;
>> + };
>> +
>> + led_left_side: led-controller-1 {
>> + compatible = "pwm-leds-multicolor";
>> +
>> + multi-led {
>> + label = "left-side";
>> + color = <LED_COLOR_ID_RGB>;
>> + max-brightness = <255>;
>> +
>> + led-red {
>> + color = <LED_COLOR_ID_RED>;
>> + pwms = <&pwm_rgb_left 0>;
>> + };
>> +
>> + led-green {
>> + color = <LED_COLOR_ID_GREEN>;
>> + pwms = <&pwm_rgb_left 1>;
>> + };
>> +
>> + led-blue {
>> + color = <LED_COLOR_ID_BLUE>;
>> + pwms = <&pwm_rgb_left 2>;
>> + };
>> + };
>> + };
>> +
>> + led_left_joystick: led-controller-2 {
>> + compatible = "pwm-leds-multicolor";
>> +
>> + multi-led {
>> + label = "left-joystick";
>> + color = <LED_COLOR_ID_RGB>;
>> + max-brightness = <255>;
>> +
>> + led-red {
>> + color = <LED_COLOR_ID_RED>;
>> + pwms = <&pwm_rgb_left 6>;
>> + };
>> +
>> + led-green {
>> + color = <LED_COLOR_ID_GREEN>;
>> + pwms = <&pwm_rgb_left 7>;
>> + };
>> +
>> + led-blue {
>> + color = <LED_COLOR_ID_BLUE>;
>> + pwms = <&pwm_rgb_left 8>;
>> + };
>> + };
>> + };
>> +
>> + led_right_side: led-controller-3 {
>> + compatible = "pwm-leds-multicolor";
>> +
>> + multi-led {
>> + label = "right-side";
>> + color = <LED_COLOR_ID_RGB>;
>> + max-brightness = <255>;
>> +
>> + led-red {
>> + color = <LED_COLOR_ID_RED>;
>> + pwms = <&pwm_rgb_right 0>;
>> + };
>> +
>> + led-green {
>> + color = <LED_COLOR_ID_GREEN>;
>> + pwms = <&pwm_rgb_right 1>;
>> + };
>> +
>> + led-blue {
>> + color = <LED_COLOR_ID_BLUE>;
>> + pwms = <&pwm_rgb_right 2>;
>> + };
>> + };
>> + };
>> +
>> + led_right_joystick: led-controller-4 {
>> + compatible = "pwm-leds-multicolor";
>> +
>> + multi-led {
>> + label = "right-joystick";
>> + color = <LED_COLOR_ID_RGB>;
>> + max-brightness = <255>;
>> +
>> + led-red {
>> + color = <LED_COLOR_ID_RED>;
>> + pwms = <&pwm_rgb_right 6>;
>> + };
>> +
>> + led-green {
>> + color = <LED_COLOR_ID_GREEN>;
>> + pwms = <&pwm_rgb_right 7>;
>> + };
>> +
>> + led-blue {
>> + color = <LED_COLOR_ID_BLUE>;
>> + pwms = <&pwm_rgb_right 8>;
>> + };
>> + };
>> + };
>> +
>> + mcu_3v3: mcu-3v3-regulator {
>
> Name all regulators regulator-n, where n is decimal number. Then order
> the nodes by name.
>
>
> ...
>
>> +
>> +&i2c4 {
>> + clock-frequency = <400000>;
>> + status = "okay";
>> +
>> + touchscreen@20 {
>> + compatible = "syna,rmi4-i2c";
>> + reg = <0x20>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupts-extended = <&tlmm 25 0x2008>;
>> +
>> + pinctrl-names = "default", "sleep";
>> + pinctrl-0 = <&ts_int_default>;
>> + pinctrl-1 = <&ts_int_sleep>;
>> +
>> + vio-supply = <&vreg_l12b_1p8>;
>> +
>> + syna,startup-delay-ms = <200>;
>> + syna,reset-delay-ms = <200>;
>> +
>> + rmi4-f01@1 {
>> + syna,nosleep-mode = <0x1>;
>> + reg = <0x1>;
>> + };
>> +
>> + rmi4-f12@12 {
>> + reg = <0x12>;
>> + syna,rezero-wait-ms = <20>;
>> + syna,clip-x-low = <0>;
>> + syna,clip-y-low = <0>;
>> + syna,clip-x-high = <1080>;
>> + syna,clip-y-high = <1920>;
>> + syna,sensor-type = <1>;
>> + touchscreen-inverted-x;
>> + };
>> + };
>
> Please confirm the status of dtbs_check for your board. I am pretty sure
> it fails.
>
> Best regards,
> Krzysztof
>
I will correct all the mistakes in v2. Thanks for catching them!
--
Thanks,
Xilin Wu
On 24.04.2024 5:29 PM, Xilin Wu via B4 Relay wrote:
> From: Xilin Wu <[email protected]>
>
> AYN Odin 2 is a gaming handheld based on QCS8550, which is derived
> from SM8550 but without modem RF system.
>
> This commit brings support for:
> * Remoteprocs
> * UFS storage
> * SD Card
> * Type-C with USB3 10Gbps and DisplayPort (4-lane requires a pending
> patch)
> * PCIe0 (Wi-Fi requires the pending pwrseq series)
> * Bluetooth
> * Regulators
> * Integrated fan with automatic speed control based on CPU temperature
> * Power and volume keys
> * M1, M2 buttons
> * HDMI output up to 1080p 60hz
> * four groups of RGB lights
> * GPU
> * Internal DSI display with touchscreen
>
> Signed-off-by: Xilin Wu <[email protected]>
> ---
[...]
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pmk8550_pwm 0 860000>;
> + brightness-levels = <1023 0>;
Huh? Is min/max swapped?
> + num-interpolated-steps = <1023>;
> + default-brightness-level = <600>;
> + power-supply = <&vph_pwr>;
> + enable-gpios = <&pmk8550_gpios 5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm_backlight_default>;
property-n
property-names
[...]
> + cooling-maps {
> + map0 {
> + trip = <&cpuss0_active0>;
> + cooling-device = <&fan 0 1>;
> + };
Please adda a newline between each subnode
[...]
> + /* Setting regulator-allow-set-load here will crash the device */
??
> + vreg_l17b_2p5: ldo17 {
> + regulator-name = "vreg_l17b_2p5";
> + regulator-min-microvolt = <2504000>;
> + regulator-max-microvolt = <2504000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
[...]
> +
> + backlight = <&backlight>;
> + /* touchscreen and display panel share the same reset gpio! */
> + reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
Perhaps you would be interested in drm_panel_follower
[...]
> +
> +&sdhc_2 {
> + cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
> + pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
> + vmmc-supply = <&vreg_l9b_2p9>;
> + vqmmc-supply = <&vreg_l8b_1p8>;
> + bus-width = <4>;
> + no-sdio;
> + no-mmc;
> +
> + /* SDR104 does seem to be working on this device*/
> + /delete-property/ sdhci-caps-mask;
Eeeh.. I'm not sure about this. Maybe it still has some issues that
don't manifest immediately.
[...]
> +&uart15 {
> + status = "okay";
> +
> + /* Gamepad controlled by onboard MCU */
As in, that MCU is connected to 8550 through this UART port?
Konrad