I tried to setup my Dell Inspiron 7500 notebook (Celeron 466/512MB) with
TORiSAN DVD-ROM DRD-U62 (RPC-2 drive :-( ) to watch DVD and found the
following when using decss to read the encrypted vob files (other ways
to access the file eventually produce the same error) under 2.4.12
kernel, RedHat Linux 7.1. After I authenticated the drive and got a
title key for some file, css-cat always fails on the first 2-3 attempts
to read the file due to input-output error with kernel message:
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x50
end_request: I/O error, dev 16:00 (hdc), sector 563008
After that vob file on third-forth attempt can be successfullyread. I
added error printouts to the program and find out that on the first
attempt css-cat in general fails during read call on some 2k block at
the very beginning of the file, on the second attempt it proceeds
farther, but around 1000-2000 block it fails again and in general the
third attempt either fails around the same offset or proceed with
calling read on each 2K block without problems. Then I tried to use
after the drive authentication something like
dd bs=2048 if=/mnt/cdrom/ of=/dev/null
it shows exactly the same behavior as css-cat.
When I use dd to read a vob file from a newly inserted DVD without any
authentication, it fails to read about 5% of all 2K file blocks with the
same error or with messages like:
hdc: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hdc: cdrom_decode_status: error=0x30
hdc: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hdc: cdrom_decode_status: error=0x30
hdc: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hdc: cdrom_decode_status: error=0x30
hdc: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hdc: cdrom_decode_status: error=0x30
hdc: DMA disabled
hdc: ATAPI reset complete
hdc: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hdc: cdrom_decode_status: error=0x30
Sometimes on the second attempt it managed to read a block initially
reported as bad, but in general quite a few blocks were not accessible
at all until obtaining title key via tstdvd from the decss package. I
can understand that my RPC-2 DVD-ROM can introduce "errors" on some
sectors until issuing authentication ioctl calls but why I have the read
errors unless I tried to read the drive 3-4 times after the authentication?
I also tried to mount dvd as the udf file system instead of iso9660 or
use ide-scsi with no difference.
Regards, Igor
On Sun, 2001-10-14 at 20:32, Igor Bukanov wrote:
> I tried to setup my Dell Inspiron 7500 notebook (Celeron 466/512MB) with
> TORiSAN DVD-ROM DRD-U62 (RPC-2 drive :-( ) to watch DVD and found the
> following when using decss to read the encrypted vob files (other ways
> to access the file eventually produce the same error) under 2.4.12
> kernel, RedHat Linux 7.1. After I authenticated the drive and got a
> title key for some file, css-cat always fails on the first 2-3 attempts
> to read the file due to input-output error with kernel message:
>
> hdc: command error: status=0x51 { DriveReady SeekComplete Error }
> hdc: command error: error=0x50
> end_request: I/O error, dev 16:00 (hdc), sector 563008
>
Under the IDE/ATAPI configuration stuff in the kernel configuration
select the option "Use multi-mode by default." That may solve your
problem.
--
John Tobin
[email protected]; AOL IM: ogre7929
http://ogre.rocky-road.net
http://ogre.rocky-road.net/cdr.shtml