Ever since I upgraded my kernel to 2.4.21-rc{1|2} from 2.4.20
I can't enable DMA on my harddisk anymore.
hdparm -d1 returns
HDIO_SET_DMA failed: Operation not permitted
What am I missing? I looked through the archive, and couldn't
find any discussion on this (I apologize if this has been discusses
before).
Please 'CC me on replies as I'm not subscribed to the list.
Thanks.
-- Lars
I attached some info on my system:
hdparm -i /dev/hda
------------------
/dev/hda:
Model=HITACHI_DK23CA-30, FwRev=00H0A0G3, SerialNo=119T7D
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=36477, SectSize=579, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=58605120
IORDY=yes, tPIO={min:400,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3
udma4 *udma5
AdvancedPM=yes: mode=0x80 (128)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 3 : ATA-1 ATA-2 ATA-3
ATA-4 ATA-5
lspci -v
--------
00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and
Memory Controller Hub (rev 04)
Flags: bus master, fast devsel, latency 0
Memory at e8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [88] #09 [e104]
Capabilities: [a0] AGP version 2.0
00:01.0 PCI bridge: Intel Corporation: Unknown device 1131 (rev 04)
(prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, fast devsel, latency 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc000000-fdffffff
Prefetchable memory behind bridge: e0000000-e7ffffff
00:1e.0 PCI bridge: Intel Corporation 82801BA PCI (rev 03) (prog-if 00
[Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=10, sec-latency=32
I/O behind bridge: 0000d000-0000ffff
Memory behind bridge: f2000000-fbffffff
00:1f.0 ISA bridge: Intel Corporation 82801BAM ISA Bridge (ICH2) (rev 03)
Flags: bus master, medium devsel, latency 0
00:1f.1 IDE interface: Intel Corporation 82801BAM IDE U100 (rev 03)
(prog-if 80 [Master])
Subsystem: Intel Corporation: Unknown device 4541
Flags: bus master, medium devsel, latency 0
I/O ports at bfa0 [size=16]
00:1f.2 USB Controller: Intel Corporation 82801BA(M) USB (Hub A) (rev
03) (prog-if 00 [UHCI])
Subsystem: Intel Corporation: Unknown device 4541
Flags: bus master, medium devsel, latency 0, IRQ 10
I/O ports at bce0 [size=32]
01:00.0 VGA compatible controller: nVidia Corporation: Unknown device
0112 (rev b2) (prog-if 00 [VGA])
Subsystem: Dell Computer Corporation: Unknown device 00e6
Flags: bus master, VGA palette snoop, 66Mhz, medium devsel, latency
248, IRQ 11
Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Memory at e0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 2.0
02:03.0 Multimedia audio controller: ESS Technology ES1983S Maestro-3i
PCI Audio Accelerator (rev 10)
Subsystem: Dell Computer Corporation: Unknown device 00e6
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at dc00 [size=256]
Memory at f6ffe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [c0] Power Management version 2
02:06.0 PCI bridge: Action Tec Electronics Inc: Unknown device 0100 (rev
11) (prog-if 00 [Normal decode])
Flags: bus master, medium devsel, latency 32
Bus: primary=02, secondary=08, subordinate=08, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f8000000-f9ffffff
Capabilities: [80] Power Management version 2
Capabilities: [90] #06 [0000]
02:0f.0 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
Subsystem: Dell Computer Corporation: Unknown device 00e6
Flags: bus master, medium devsel, latency 168, IRQ 10
Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=09, subordinate=0c, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001
02:0f.1 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
Subsystem: Dell Computer Corporation: Unknown device 00e6
Flags: bus master, medium devsel, latency 168, IRQ 10
Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=0d, subordinate=10, sec-latency=176
Memory window 0: 10c00000-10fff000 (prefetchable)
Memory window 1: 11000000-113ff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
16-bit legacy interface ports at 0001
02:0f.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8027
(prog-if 10 [OHCI])
Subsystem: Dell Computer Corporation: Unknown device 00e6
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at f6ffd800 (32-bit, non-prefetchable) [size=2K]
Memory at f6ff8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
08:04.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100]
(rev 08)
Subsystem: Action Tec Electronics Inc: Unknown device 1100
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at f8fff000 (32-bit, non-prefetchable) [size=4K]
I/O ports at ecc0 [size=64]
Memory at f8e00000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at f9000000 [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
08:08.0 Communication controller: Lucent Microelectronics WinModem 56k
(rev 01)
Subsystem: Action Tec Electronics Inc: Unknown device 2400
Flags: bus master, medium devsel, latency 0, IRQ 10
Memory at f8ffec00 (32-bit, non-prefetchable) [size=256]
I/O ports at ecb8 [size=8]
I/O ports at e800 [size=256]
Capabilities: [f8] Power Management version 2
I have the same problem on VIA chipset. IDE DMA is disabled in
2.4.21-rc2 but works fine otherwise:
root@noodles /etc # hdparm -d 1 /dev/hda
/dev/hda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
root@noodles /etc # lspci -v
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P] System Contr
ller (rev 13)
Flags: bus master, medium devsel, latency 32
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Memory at f7005000 (32-bit, prefetchable) [size=4K]
I/O ports at a000 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 [IGD4-1P] AGP Bridge (p
rog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: f4000000-f5ffffff
Prefetchable memory behind bridge: e8000000-efffffff
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40
)
Subsystem: ABIT Computer Corp. KG7-Lite Mainboard
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master
IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT8235 Bus Master ATA133/100/66/33 IDE
Flags: bus master, medium devsel, latency 32
I/O ports at a400 [size=16]
Capabilities: [c0] Power Management version 2
00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 15
I/O ports at a800 [size=32]
Capabilities: [80] Power Management version 2
00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 15
I/O ports at ac00 [size=32]
Capabilities: [80] Power Management version 2
00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Flags: medium devsel, IRQ 5
Capabilities: [68] Power Management version 2
00:08.0 SCSI storage controller: Adaptec AHA-7850 (rev 03)
Subsystem: Adaptec AHA-2904/Integrated AIC-7850
Flags: bus master, medium devsel, latency 32, IRQ 15
I/O ports at b000 [disabled] [size=256]
Memory at f7008000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 1
00:09.0 SCSI storage controller: Adaptec AHA-2940U/UW/D / AIC-7881U
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at b400 [disabled] [size=256]
Memory at f7004000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:0b.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 05)
Subsystem: Creative Labs CT4760 SBLive!
Flags: bus master, medium devsel, latency 32, IRQ 15
I/O ports at b800 [size=32]
Capabilities: [dc] Power Management version 1
00:0b.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 05)
Subsystem: Creative Labs Gameport Joystick
Flags: bus master, medium devsel, latency 32
I/O ports at bc00 [size=8]
Capabilities: [dc] Power Management version 1
00:0d.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 20)
Subsystem: Kingston Technologies: Unknown device f002
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at c000 [size=256]
Memory at f7006000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=256K]
00:0f.0 FireWire (IEEE 1394): Texas Instruments TSB12LV26 IEEE-1394 Controller (
Link) (prog-if 10 [OHCI])
Subsystem: Procomp Informatics Ltd: Unknown device 8010
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at f7007000 (32-bit, non-prefetchable) [size=2K]
Memory at f7000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 1
01:05.0 VGA compatible controller: ATI Technologies Inc Radeon R100 QD [Radeon 7
200] (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Radeon AIW
Flags: bus master, stepping, 66Mhz, medium devsel, latency 32, IRQ 12
Memory at e8000000 (32-bit, prefetchable) [size=128M]
I/O ports at 9000 [size=256]
Memory at f5000000 (32-bit, non-prefetchable) [size=512K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Capabilities: [50] Power Management version 2
> [[email protected]]
>
> I have the same problem on VIA chipset. IDE DMA is disabled in
> 2.4.21-rc2 but works fine otherwise:
Please post the relevant extract of your .config and dmesg output.
--
Tomas Szepe <[email protected]>
Tomas Szepe wrote:
>>[[email protected]]
>>
>>I have the same problem on VIA chipset. IDE DMA is disabled in
>>2.4.21-rc2 but works fine otherwise:
>
>
> Please post the relevant extract of your .config and dmesg output.
>
Here's all the information:
dmesg:
------
...
PCI: PCI BIOS revision 2.10 entry at 0xfc06e, last bus=8
PCI: Using configuration type 1
PCI: Probing PCI hardware
Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge
PCI: Using IRQ router PIIX [8086/244c] at 00:1f.0
...
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: HITACHI_DK23CA-30, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-C2502, ATAPI CD/DVD-ROM drive
hdc: TOSHIBA CD-RW/DVD-ROM SD-R2102, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 58605120 sectors (30006 MB) w/2048KiB Cache, CHS=3648/255/63
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 >
.config:
--------
...
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_ISA=y
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
CONFIG_HOTPLUG=y
...
#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set
#
# IDE chipset support/bugfixes
#
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_ADMA100 is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_RZ1000 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
# CONFIG_BLK_DEV_ATARAID_SII is not set
...
lspci:
------
00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and
Memory Controller Hub (rev 04)
00:01.0 PCI bridge: Intel Corporation: Unknown device 1131 (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801BA PCI (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801BAM ISA Bridge (ICH2) (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801BAM IDE U100 (rev 03)
00:1f.2 USB Controller: Intel Corporation 82801BA(M) USB (Hub A) (rev 03)
01:00.0 VGA compatible controller: nVidia Corporation: Unknown device
0112 (revb2)
02:03.0 Multimedia audio controller: ESS Technology ES1983S Maestro-3i
PCI Audio Accelerator (rev 10)
02:06.0 PCI bridge: Action Tec Electronics Inc: Unknown device 0100 (rev 11)
02:0f.0 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
02:0f.1 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
02:0f.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8027
08:04.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100]
(rev 08)08:08.0 Communication controller: Lucent Microelectronics
WinModem 56k (rev 01)
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
I think that is the offending line?
can you enable DMA transfer modes on the drive using hdparm?
--eric
-----Original Message-----
From: Lars [mailto:[email protected]]
Sent: Sunday, May 18, 2003 9:03 PM
To: Tomas Szepe
Cc: Jeffrey Baker; [email protected]
Subject: Re: HD DMA disabled in 2.4.21-rc2, works fine in 2.4.20
Tomas Szepe wrote:
>>[[email protected]]
>>
>>I have the same problem on VIA chipset. IDE DMA is disabled in
>>2.4.21-rc2 but works fine otherwise:
>
>
> Please post the relevant extract of your .config and dmesg output.
>
Here's all the information:
dmesg:
------
...
PCI: PCI BIOS revision 2.10 entry at 0xfc06e, last bus=8
PCI: Using configuration type 1
PCI: Probing PCI hardware
Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge
PCI: Using IRQ router PIIX [8086/244c] at 00:1f.0
...
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: HITACHI_DK23CA-30, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-C2502, ATAPI CD/DVD-ROM drive
hdc: TOSHIBA CD-RW/DVD-ROM SD-R2102, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 58605120 sectors (30006 MB) w/2048KiB Cache, CHS=3648/255/63
Partition check:
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 hda9 hda10 >
.config:
--------
...
#
# General setup
#
CONFIG_NET=y
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_ISA=y
CONFIG_PCI_NAMES=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
CONFIG_HOTPLUG=y
...
#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
CONFIG_BLK_DEV_IDEFLOPPY=m
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set
#
# IDE chipset support/bugfixes
#
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_ISAPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_BLK_DEV_ADMA100 is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_WDC_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_HPT34X_AUTODMA is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_PDC202XX_BURST is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_RZ1000 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
# CONFIG_BLK_DEV_ATARAID_SII is not set
...
lspci:
------
00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and
Memory Controller Hub (rev 04)
00:01.0 PCI bridge: Intel Corporation: Unknown device 1131 (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801BA PCI (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801BAM ISA Bridge (ICH2) (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801BAM IDE U100 (rev 03)
00:1f.2 USB Controller: Intel Corporation 82801BA(M) USB (Hub A) (rev 03)
01:00.0 VGA compatible controller: nVidia Corporation: Unknown device
0112 (revb2)
02:03.0 Multimedia audio controller: ESS Technology ES1983S Maestro-3i
PCI Audio Accelerator (rev 10)
02:06.0 PCI bridge: Action Tec Electronics Inc: Unknown device 0100 (rev 11)
02:0f.0 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
02:0f.1 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
02:0f.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8027
08:04.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100]
(rev 08)08:08.0 Communication controller: Lucent Microelectronics
WinModem 56k (rev 01)
On Mon, 2003-05-19 at 12:56, Mudama, Eric wrote:
> # CONFIG_BLK_DEV_IDEDMA_FORCED is not set
>
> I think that is the offending line?
>
> can you enable DMA transfer modes on the drive using hdparm?
Why should force be enabled? Forced sounds like a last resort. If you
read this thread you will see that hdparm isn't working. It returns
EPERM.
I was using Via IDE chipset and, yes, I had configured the kernel for
VIA support. That's why it worked in 2.4.20. But it stopped working in
2.4.21-rc.
Meanwhile, I have switched to 2.4.21-rc-ac, and dumped the hardware in
favor of Intel i865, and DMA is working again.
-jwb
On Llu, 2003-05-19 at 21:04, Jeffrey W. Baker wrote:
> I was using Via IDE chipset and, yes, I had configured the kernel for
> VIA support. That's why it worked in 2.4.20. But it stopped working in
> 2.4.21-rc.
VIA IDE should be working reliably, my main test box is an EPIA series
VIA system so the VIA IDE does get a fair beating
> [[email protected]]
>
> On Llu, 2003-05-19 at 21:04, Jeffrey W. Baker wrote:
> > I was using Via IDE chipset and, yes, I had configured the kernel for
> > VIA support. That's why it worked in 2.4.20. But it stopped working in
> > 2.4.21-rc.
>
> VIA IDE should be working reliably, my main test box is an EPIA series
> VIA system so the VIA IDE does get a fair beating
This person is running with CONFIG_BLK_DEV_VIA82CXXX unset.
--
Tomas Szepe <[email protected]>
On Mon, 2003-05-19 at 15:29, Tomas Szepe wrote:
> > [[email protected]]
> >
> > On Llu, 2003-05-19 at 21:04, Jeffrey W. Baker wrote:
> > > I was using Via IDE chipset and, yes, I had configured the kernel for
> > > VIA support. That's why it worked in 2.4.20. But it stopped working in
> > > 2.4.21-rc.
> >
> > VIA IDE should be working reliably, my main test box is an EPIA series
> > VIA system so the VIA IDE does get a fair beating
>
> This person is running with CONFIG_BLK_DEV_VIA82CXXX unset.
No, this person is not.
-jwb
The person who posted their DMESG had it unset.
Here's an archive of the post:
http://www.ussg.iu.edu/hypermail/linux/kernel/0305.2/0440.html
And the line:
# CONFIG_BLK_DEV_VIA82CXXX is not set
From: Lars ([email protected])
Date: Sun May 18 2003 - 22:03:16 EST
--eric
-----Original Message-----
From: Jeffrey W. Baker [mailto:[email protected]]
Sent: Monday, May 19, 2003 5:01 PM
To: Tomas Szepe; [email protected]
Subject: Re: HD DMA disabled in 2.4.21-rc2, works fine in 2.4.20
On Mon, 2003-05-19 at 15:29, Tomas Szepe wrote:
> > [[email protected]]
> >
> > On Llu, 2003-05-19 at 21:04, Jeffrey W. Baker wrote:
> > > I was using Via IDE chipset and, yes, I had configured the kernel for
> > > VIA support. That's why it worked in 2.4.20. But it stopped working
in
> > > 2.4.21-rc.
> >
> > VIA IDE should be working reliably, my main test box is an EPIA series
> > VIA system so the VIA IDE does get a fair beating
>
> This person is running with CONFIG_BLK_DEV_VIA82CXXX unset.
No, this person is not.
-jwb
No hdparm does not allow me to.
I can't check the exact error msg right now (at work),
but previous messages in this thread have it.
-- Lars
--- "Mudama, Eric" <[email protected]> wrote:
>
> # CONFIG_BLK_DEV_IDEDMA_FORCED is not set
>
> I think that is the offending line?
>
> can you enable DMA transfer modes on the drive using
> hdparm?
>
> --eric
>
[ lots of other discussion deleted ]
__________________________________
Do you Yahoo!?
The New Yahoo! Search - Faster. Easier. Bingo.
http://search.yahoo.com
Please read the entire thread.
I am the person who started the thread and yes, I have
# CONFIG_BLK_DEV_VIA82CXXX is not set
Then again, I also do not have a VIA chipset, Jeffrey had
the same problem and he has the VIA chipset, that's where
the confusion comes from.
From the same post:
00:1e.0 PCI bridge: Intel Corporation 82801BA PCI (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801BAM ISA Bridge (ICH2) (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801BAM IDE U100 (rev 03)
It seems to me that I'm missing something very obvious.
Anyway, as there seems to be no solution at hand for me, so I'm back
to 2.4.20 for the time being until I have time have a look at the
source myself.
-- Lars
-----------------------------------------------------------------
The person who posted their DMESG had it unset.
Here's an archive of the post:
http://www.ussg.iu.edu/hypermail/linux/kernel/0305.2/0440.html
And the line:
# CONFIG_BLK_DEV_VIA82CXXX is not set
From: Lars ([email protected])
Date: Sun May 18 2003 - 22:03:16 EST
--eric
-----Original Message-----
From: Jeffrey W. Baker [mailto:[email protected]]
Sent: Monday, May 19, 2003 5:01 PM
To: Tomas Szepe; [email protected]
Subject: Re: HD DMA disabled in 2.4.21-rc2, works fine in 2.4.20
On Mon, 2003-05-19 at 15:29, Tomas Szepe wrote:
> > [[email protected]]
> >
> > On Llu, 2003-05-19 at 21:04, Jeffrey W. Baker wrote:
> > > I was using Via IDE chipset and, yes, I had configured the kernel for
> > > VIA support. That's why it worked in 2.4.20. But it stopped working
in
> > > 2.4.21-rc.
> >
> > VIA IDE should be working reliably, my main test box is an EPIA series
> > VIA system so the VIA IDE does get a fair beating
>
> This person is running with CONFIG_BLK_DEV_VIA82CXXX unset.
No, this person is not.
-jwb
Solved!
I looked at the 2.4.20 output and saw ICH2M mentioned in the
output. I then grepped the drivers/ide/pci files for ICH2M
and found I just had to enable CONFIG_BLK_DEV_PIIX.
In my defense I can only say that the Configure.help
stated that this option only enables extended PIO modes.
So for the record: A Dell Inspiron 8100 Laptop needs
the CONFIG_BLK_DEV_PIIX to enable DMA.
-- Lars
Someone Please Help! I would really like to get 2.5.69 to boot correctly
with modules before 2.5.70 comes out! I will be eternally grateful and
promise to help all the other redhat users with the same problem if I
can figure it out:)
Anyway I get not found messages when redhat modprobes char-major-10-1,
eth1, etc. when it boots up. This seems to be related to aliases since
eth1 is aliased to sis900 and char-major-10-1 to psaux. All help greatly
appreciated... exact details and .config file below:
What am I not doing wrong? or is this something strange with redhat?
Please help!
I have installed module-init tools as follows:
Upgrade to rusty's latest modutils.
Get module-init tools 12
./configure --prefix=/ # copy over old utils in /bin and /sbin
make moveold
make
make install
# build the kernel, and reboot
I also tried to run the generate modprobe.conf script with no changes to
the behavior.
.config follow:
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_IKCONFIG is not set
CONFIG_MORSE_PANICS=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
CONFIG_MPENTIUMII=y
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
# CONFIG_X86_MCE_NONFATAL is not set
CONFIG_X86_MCE_P4THERMAL=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
CONFIG_EDD=m
# CONFIG_NOHIGHMEM is not set
CONFIG_HIGHMEM4G=y
# CONFIG_HIGHMEM64G is not set
CONFIG_HIGHMEM=y
# CONFIG_HIGHPTE is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
# CONFIG_SOFTWARE_SUSPEND is not set
#
# ACPI Support
#
# CONFIG_ACPI is not set
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
CONFIG_APM_CPU_IDLE=y
# CONFIG_APM_DISPLAY_BLANK is not set
CONFIG_APM_RTC_IS_GMT=y
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set
#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
CONFIG_EISA=y
# CONFIG_EISA_VLB_PRIMING is not set
CONFIG_EISA_PCI_EISA=y
CONFIG_EISA_VIRTUAL_ROOT=y
CONFIG_EISA_NAMES=y
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
CONFIG_HOTPLUG=y
#
# PCMCIA/CardBus support
#
CONFIG_PCMCIA=m
CONFIG_CARDBUS=y
CONFIG_I82092=m
CONFIG_I82365=m
CONFIG_TCIC=m
CONFIG_PCMCIA_PROBE=y
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
#
# Executable file formats
#
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
CONFIG_PARPORT_SERIAL=m
CONFIG_PARPORT_PC_FIFO=y
# CONFIG_PARPORT_PC_SUPERIO is not set
CONFIG_PARPORT_PC_PCMCIA=m
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y
#
# Plug and Play support
#
CONFIG_PNP=y
CONFIG_PNP_NAMES=y
CONFIG_PNP_DEBUG=y
#
# Protocols
#
CONFIG_ISAPNP=y
# CONFIG_PNPBIOS is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
CONFIG_PARIDE=m
CONFIG_PARIDE_PARPORT=m
#
# Parallel IDE high-level drivers
#
CONFIG_PARIDE_PD=m
CONFIG_PARIDE_PCD=m
CONFIG_PARIDE_PF=m
CONFIG_PARIDE_PT=m
CONFIG_PARIDE_PG=m
#
# Parallel IDE protocol modules
#
CONFIG_PARIDE_ATEN=m
CONFIG_PARIDE_BPCK=m
CONFIG_PARIDE_BPCK6=m
CONFIG_PARIDE_COMM=m
CONFIG_PARIDE_DSTR=m
CONFIG_PARIDE_FIT2=m
CONFIG_PARIDE_FIT3=m
CONFIG_PARIDE_EPAT=m
CONFIG_PARIDE_EPATC8=y
CONFIG_PARIDE_EPIA=m
CONFIG_PARIDE_FRIQ=m
CONFIG_PARIDE_FRPW=m
CONFIG_PARIDE_KBIC=m
CONFIG_PARIDE_KTTI=m
CONFIG_PARIDE_ON20=m
CONFIG_PARIDE_ON26=m
CONFIG_BLK_CPQ_DA=m
CONFIG_BLK_CPQ_CISS_DA=m
CONFIG_CISS_SCSI_TAPE=y
CONFIG_BLK_DEV_DAC960=m
CONFIG_BLK_DEV_UMEM=m
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
# CONFIG_LBD is not set
#
# ATA/ATAPI/MFM/RLL device support
#
CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_IDEDISK_STROKE=y
CONFIG_BLK_DEV_IDECS=m
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=m
# CONFIG_IDE_TASK_IOCTL is not set
#
# IDE chipset support/bugfixes
#
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDE_TCQ is not set
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_AEC62XX=y
CONFIG_BLK_DEV_ALI15X3=y
# CONFIG_WDC_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
CONFIG_BLK_DEV_CMD64X=y
CONFIG_BLK_DEV_TRIFLEX=y
CONFIG_BLK_DEV_CY82C693=y
# CONFIG_BLK_DEV_CS5520 is not set
CONFIG_BLK_DEV_HPT34X=y
CONFIG_BLK_DEV_HPT366=y
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_PDC202XX_OLD=y
CONFIG_BLK_DEV_PDC202XX_NEW=y
CONFIG_PDC202XX_FORCE=y
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_SVWKS=y
CONFIG_BLK_DEV_SIIMAGE=y
CONFIG_BLK_DEV_SIS5513=y
CONFIG_BLK_DEV_SLC90E66=y
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_CHIPSETS is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_BLK_DEV_PDC202XX=y
CONFIG_BLK_DEV_IDE_MODES=y
#
# SCSI device support
#
CONFIG_SCSI=m
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
CONFIG_CHR_DEV_ST=m
CONFIG_CHR_DEV_OSST=m
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_REPORT_LUNS=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
CONFIG_SCSI_AHA152X=m
CONFIG_SCSI_AHA1542=m
CONFIG_SCSI_AHA1740=m
CONFIG_SCSI_AACRAID=m
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_PROBE_EISA_VL is not set
# CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
CONFIG_AIC7XXX_DEBUG_MASK=0
# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
CONFIG_SCSI_FUTURE_DOMAIN=m
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
CONFIG_SCSI_GENERIC_NCR5380_MMIO=m
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
CONFIG_SCSI_PPA=m
CONFIG_SCSI_IMM=m
# CONFIG_SCSI_IZIP_EPP16 is not set
# CONFIG_SCSI_IZIP_SLOW_CTR is not set
# CONFIG_SCSI_NCR53C406A is not set
CONFIG_53C700_IO_MAPPED=y
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
CONFIG_SCSI_QLOGIC_FAS=m
CONFIG_SCSI_QLOGIC_ISP=m
CONFIG_SCSI_QLOGIC_FC=m
# CONFIG_SCSI_QLOGIC_FC_FIRMWARE is not set
CONFIG_SCSI_QLOGIC_1280=m
CONFIG_SCSI_SEAGATE=m
CONFIG_SCSI_SIM710=m
CONFIG_SCSI_SYM53C416=m
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
CONFIG_SCSI_U14_34F=m
# CONFIG_SCSI_U14_34F_TAGGED_QUEUE is not set
# CONFIG_SCSI_U14_34F_LINKED_COMMANDS is not set
CONFIG_SCSI_U14_34F_MAX_TAGS=8
CONFIG_SCSI_ULTRASTOR=m
CONFIG_SCSI_NSP32=m
CONFIG_SCSI_DEBUG=m
#
# PCMCIA SCSI adapter support
#
CONFIG_PCMCIA_AHA152X=m
CONFIG_PCMCIA_FDOMAIN=m
CONFIG_PCMCIA_NINJA_SCSI=m
CONFIG_PCMCIA_QLOGIC=m
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
CONFIG_FUSION=m
CONFIG_FUSION_MAX_SGE=40
# CONFIG_FUSION_ISENSE is not set
CONFIG_FUSION_CTL=m
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
CONFIG_IEEE1394=m
#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
#
# Device Drivers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=m
#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
CONFIG_IEEE1394_SBP2_PHYS_DMA=y
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_IEEE1394_CMP=m
CONFIG_IEEE1394_AMDTP=m
#
# I2O device support
#
CONFIG_I2O=m
CONFIG_I2O_PCI=m
CONFIG_I2O_BLOCK=m
CONFIG_I2O_SCSI=m
CONFIG_I2O_PROC=m
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK_DEV=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_IP_MULTIPLE_TABLES=y
CONFIG_IP_ROUTE_FWMARK=y
CONFIG_IP_ROUTE_NAT=y
CONFIG_IP_ROUTE_MULTIPATH=y
CONFIG_IP_ROUTE_TOS=y
CONFIG_IP_ROUTE_VERBOSE=y
CONFIG_IP_ROUTE_LARGE_TABLES=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
CONFIG_SYN_COOKIES=y
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
# CONFIG_IP_NF_TFTP is not set
# CONFIG_IP_NF_AMANDA is not set
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_UNCLEAN=m
CONFIG_IP_NF_MATCH_OWNER=m
# CONFIG_IP_NF_MATCH_PHYSDEV is not set
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_MIRROR=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
# CONFIG_IP_NF_NAT_LOCAL is not set
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_COMPAT_IPCHAINS=m
CONFIG_IP_NF_COMPAT_IPFWADM=m
CONFIG_IPV6=m
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
#
# IPv6: Netfilter Configuration
#
# CONFIG_IP6_NF_QUEUE is not set
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_LIMIT=m
CONFIG_IP6_NF_MATCH_MAC=m
# CONFIG_IP6_NF_MATCH_RT is not set
# CONFIG_IP6_NF_MATCH_OPTS is not set
# CONFIG_IP6_NF_MATCH_FRAG is not set
# CONFIG_IP6_NF_MATCH_HL is not set
CONFIG_IP6_NF_MATCH_MULTIPORT=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_MARK=m
# CONFIG_IP6_NF_MATCH_IPV6HEADER is not set
# CONFIG_IP6_NF_MATCH_AHESP is not set
CONFIG_IP6_NF_MATCH_LENGTH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_MARK=m
# CONFIG_XFRM_USER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IPV6_SCTP__=m
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
CONFIG_VLAN_8021Q=m
# CONFIG_LLC is not set
# CONFIG_DECNET is not set
CONFIG_BRIDGE=m
# CONFIG_BRIDGE_NF_EBTABLES is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
CONFIG_NET_DIVERT=y
# CONFIG_ECONET is not set
CONFIG_WAN_ROUTER=m
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_HTB=m
CONFIG_NET_SCH_CSZ=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_INGRESS=m
CONFIG_NET_QOS=y
CONFIG_NET_ESTIMATOR=y
CONFIG_NET_CLS=y
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_CLS_POLICE=y
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
CONFIG_ETHERTAP=m
CONFIG_NET_SB1000=m
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_MII is not set
CONFIG_HAPPYMEAL=m
CONFIG_SUNGEM=m
CONFIG_NET_VENDOR_3COM=y
CONFIG_EL1=m
CONFIG_EL2=m
CONFIG_ELPLUS=m
CONFIG_EL16=m
CONFIG_EL3=m
CONFIG_3C515=m
CONFIG_VORTEX=m
# CONFIG_TYPHOON is not set
CONFIG_LANCE=m
CONFIG_NET_VENDOR_SMC=y
CONFIG_WD80x3=m
CONFIG_ULTRA=m
CONFIG_ULTRA32=m
CONFIG_SMC9194=m
CONFIG_NET_VENDOR_RACAL=y
CONFIG_NI5010=m
CONFIG_NI52=m
CONFIG_NI65=m
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
CONFIG_AT1700=m
CONFIG_DEPCA=m
CONFIG_HP100=m
CONFIG_NET_ISA=y
CONFIG_E2100=m
CONFIG_EWRK3=m
CONFIG_EEXPRESS=m
CONFIG_EEXPRESS_PRO=m
CONFIG_HPLAN_PLUS=m
CONFIG_HPLAN=m
CONFIG_LP486E=m
CONFIG_ETH16I=m
CONFIG_NE2000=m
# CONFIG_ZNET is not set
CONFIG_NET_PCI=y
CONFIG_PCNET32=m
CONFIG_AMD8111_ETH=m
CONFIG_ADAPTEC_STARFIRE=m
# CONFIG_ADAPTEC_STARFIRE_NAPI is not set
CONFIG_AC3200=m
CONFIG_APRICOT=m
# CONFIG_B44 is not set
CONFIG_CS89x0=m
CONFIG_DGRS=m
CONFIG_EEPRO100=m
# CONFIG_EEPRO100_PIO is not set
CONFIG_E100=m
CONFIG_LNE390=m
CONFIG_FEALNX=m
CONFIG_NATSEMI=m
CONFIG_NE2K_PCI=m
CONFIG_NE3210=m
CONFIG_ES3210=m
CONFIG_8139CP=m
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set
CONFIG_SIS900=m
CONFIG_EPIC100=m
CONFIG_SUNDANCE=m
CONFIG_SUNDANCE_MMIO=y
CONFIG_TLAN=m
CONFIG_VIA_RHINE=m
# CONFIG_VIA_RHINE_MMIO is not set
CONFIG_NET_POCKET=y
CONFIG_ATP=m
CONFIG_DE600=m
CONFIG_DE620=m
#
# Ethernet (1000 Mbit)
#
CONFIG_ACENIC=m
# CONFIG_ACENIC_OMIT_TIGON_I is not set
CONFIG_DL2K=m
CONFIG_E1000=m
# CONFIG_E1000_NAPI is not set
CONFIG_NS83820=m
CONFIG_HAMACHI=m
CONFIG_YELLOWFIN=m
CONFIG_R8169=m
CONFIG_SK98LIN=m
CONFIG_TIGON3=m
#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
CONFIG_PLIP=m
CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
# CONFIG_PPP_BSDCOMP is not set
# CONFIG_PPPOE is not set
CONFIG_SLIP=m
CONFIG_SLIP_COMPRESSED=y
CONFIG_SLIP_SMART=y
CONFIG_SLIP_MODE_SLIP6=y
#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y
#
# Obsolete Wireless cards support (pre-802.11)
#
CONFIG_STRIP=m
CONFIG_ARLAN=m
CONFIG_WAVELAN=m
CONFIG_PCMCIA_WAVELAN=m
CONFIG_PCMCIA_NETWAVE=m
#
# Wireless 802.11 Frequency Hopping cards support
#
CONFIG_PCMCIA_RAYCS=m
#
# Wireless 802.11b ISA/PCI cards support
#
CONFIG_AIRO=m
CONFIG_HERMES=m
CONFIG_PLX_HERMES=m
CONFIG_PCI_HERMES=m
#
# Wireless 802.11b Pcmcia/Cardbus cards support
#
CONFIG_PCMCIA_HERMES=m
CONFIG_AIRO_CS=m
CONFIG_NET_WIRELESS=y
#
# Token Ring devices (depends on LLC=y)
#
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# PCMCIA network device support
#
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_3C589=m
CONFIG_PCMCIA_3C574=m
CONFIG_PCMCIA_FMVJ18X=m
CONFIG_PCMCIA_PCNET=m
CONFIG_PCMCIA_NMCLAN=m
CONFIG_PCMCIA_SMC91C92=m
CONFIG_PCMCIA_XIRC2PS=m
CONFIG_PCMCIA_AXNET=m
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
CONFIG_IRDA=m
#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRNET=m
CONFIG_IRCOMM=m
CONFIG_IRDA_ULTRA=y
#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
# CONFIG_IRDA_DEBUG is not set
#
# Infrared-port device drivers
#
#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m
#
# Dongle support
#
CONFIG_DONGLE=y
CONFIG_ESI_DONGLE=m
CONFIG_ACTISYS_DONGLE=m
CONFIG_TEKRAM_DONGLE=m
#
# Old SIR device drivers
#
# CONFIG_IRTTY_OLD is not set
CONFIG_IRPORT_SIR=m
#
# Old Serial dongle support
#
# CONFIG_DONGLE_OLD is not set
#
# FIR device drivers
#
CONFIG_USB_IRDA=m
CONFIG_NSC_FIR=m
CONFIG_WINBOND_FIR=m
CONFIG_TOSHIBA_OLD=m
CONFIG_TOSHIBA_FIR=m
CONFIG_SMC_IRCC_FIR=m
CONFIG_ALI_FIR=m
CONFIG_VLSI_FIR=m
#
# ISDN subsystem
#
# CONFIG_ISDN_BOOL is not set
#
# Telephony Support
#
CONFIG_PHONE=m
CONFIG_PHONE_IXJ=m
CONFIG_PHONE_IXJ_PCMCIA=m
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_SERIAL=m
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
# CONFIG_INPUT_UINPUT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_DIGI is not set
# CONFIG_ESPSERIAL is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINK is not set
# CONFIG_SYNCLINKMP is not set
CONFIG_N_HDLC=m
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
# CONFIG_SERIAL_8250_CS is not set
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=2048
CONFIG_PRINTER=m
CONFIG_LP_CONSOLE=y
CONFIG_PPDEV=m
CONFIG_TIPAR=m
#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_ALGOBIT=m
CONFIG_I2C_PHILIPSPAR=m
CONFIG_I2C_ELV=m
CONFIG_I2C_VELLEMAN=m
# CONFIG_SCx200_ACB is not set
CONFIG_I2C_ALGOPCF=m
CONFIG_I2C_ELEKTOR=m
CONFIG_I2C_CHARDEV=m
#
# I2C Hardware Sensors Mainboard support
#
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_VIAPRO is not set
#
# I2C Hardware Sensors Chip support
#
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_I2C_SENSOR is not set
#
# Mice
#
CONFIG_BUSMOUSE=m
# CONFIG_QIC02_TAPE is not set
#
# IPMI
#
CONFIG_IPMI_HANDLER=m
# CONFIG_IPMI_PANIC_EVENT is not set
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_KCS=m
CONFIG_IPMI_WATCHDOG=m
#
# Watchdog Cards
#
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
CONFIG_SOFT_WATCHDOG=m
CONFIG_WDT=m
CONFIG_WDTPCI=m
# CONFIG_WDT_501 is not set
CONFIG_PCWATCHDOG=m
CONFIG_ACQUIRE_WDT=m
CONFIG_ADVANTECH_WDT=m
CONFIG_EUROTECH_WDT=m
CONFIG_IB700_WDT=m
CONFIG_I810_TCO=m
# CONFIG_MIXCOMWD is not set
# CONFIG_SCx200_WDT is not set
# CONFIG_60XX_WDT is not set
CONFIG_W83877F_WDT=m
CONFIG_MACHZ_WDT=m
CONFIG_SC520_WDT=m
CONFIG_AMD7XX_TCO=m
CONFIG_ALIM7101_WDT=m
CONFIG_SC1200_WDT=m
CONFIG_WAFER_WDT=m
# CONFIG_CPU5_WDT is not set
# CONFIG_HW_RANDOM is not set
CONFIG_NVRAM=m
CONFIG_RTC=y
CONFIG_DTLK=m
CONFIG_R3964=m
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
CONFIG_FTAPE=m
CONFIG_ZFTAPE=m
CONFIG_ZFT_DFLT_BLK_SZ=10240
#
# The compressor will be built as a module only!
#
CONFIG_ZFT_COMPRESSOR=m
CONFIG_FT_NR_BUFFERS=3
# CONFIG_FT_PROC_FS is not set
CONFIG_FT_NORMAL_DEBUG=y
# CONFIG_FT_FULL_DEBUG is not set
# CONFIG_FT_NO_TRACE is not set
# CONFIG_FT_NO_TRACE_AT_ALL is not set
#
# Hardware configuration
#
CONFIG_FT_STD_FDC=y
# CONFIG_FT_MACH2 is not set
# CONFIG_FT_PROBE_FC10 is not set
# CONFIG_FT_ALT_FDC is not set
CONFIG_FT_FDC_THR=8
CONFIG_FT_FDC_MAX_RATE=2000
CONFIG_FT_ALPHA_CLOCK=0
CONFIG_AGP=m
CONFIG_AGP_INTEL=m
CONFIG_AGP_VIA=m
CONFIG_AGP_AMD=m
CONFIG_AGP_SIS=m
CONFIG_AGP_ALI=m
CONFIG_AGP_SWORKS=m
CONFIG_AGP_AMD_8151=m
CONFIG_DRM=y
CONFIG_DRM_TDFX=m
CONFIG_DRM_R128=m
CONFIG_DRM_RADEON=m
CONFIG_DRM_I810=m
CONFIG_DRM_I830=m
CONFIG_DRM_MGA=m
#
# PCMCIA character devices
#
CONFIG_SYNCLINK_CS=m
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HANGCHECK_TIMER is not set
#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m
#
# Video For Linux
#
CONFIG_VIDEO_PROC_FS=y
#
# Video Adapters
#
CONFIG_VIDEO_BT848=m
CONFIG_VIDEO_PMS=m
CONFIG_VIDEO_BWQCAM=m
CONFIG_VIDEO_CQCAM=m
CONFIG_VIDEO_W9966=m
CONFIG_VIDEO_CPIA=m
CONFIG_VIDEO_CPIA_PP=m
CONFIG_VIDEO_CPIA_USB=m
CONFIG_VIDEO_SAA5249=m
CONFIG_TUNER_3036=m
CONFIG_VIDEO_STRADIS=m
# CONFIG_VIDEO_ZORAN is not set
# CONFIG_VIDEO_ZR36120 is not set
# CONFIG_VIDEO_SAA7134 is not set
# CONFIG_VIDEO_MXB is not set
# CONFIG_VIDEO_DPC is not set
#
# Radio Adapters
#
CONFIG_RADIO_CADET=m
CONFIG_RADIO_RTRACK=m
CONFIG_RADIO_RTRACK2=m
CONFIG_RADIO_AZTECH=m
CONFIG_RADIO_GEMTEK=m
CONFIG_RADIO_GEMTEK_PCI=m
CONFIG_RADIO_MAXIRADIO=m
CONFIG_RADIO_MAESTRO=m
CONFIG_RADIO_SF16FMI=m
CONFIG_RADIO_TERRATEC=m
CONFIG_RADIO_TRUST=m
CONFIG_RADIO_TYPHOON=m
CONFIG_RADIO_TYPHOON_PROC_FS=y
CONFIG_RADIO_ZOLTRIX=m
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
CONFIG_VIDEO_VIDEOBUF=m
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BTCX=m
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
CONFIG_JFS_FS=m
# CONFIG_JFS_POSIX_ACL is not set
CONFIG_JFS_DEBUG=y
# CONFIG_JFS_STATISTICS is not set
# CONFIG_XFS_FS is not set
CONFIG_MINIX_FS=m
CONFIG_ROMFS_FS=m
CONFIG_QUOTA=y
# CONFIG_QFMT_V1 is not set
CONFIG_QFMT_V2=y
CONFIG_QUOTACTL=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=m
#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
CONFIG_DEVPTS_FS=y
CONFIG_TMPFS=y
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
CONFIG_HFS_FS=m
CONFIG_BEFS_FS=m
# CONFIG_BEFS_DEBUG is not set
CONFIG_BFS_FS=m
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=m
CONFIG_VXFS_FS=m
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
CONFIG_SYSV_FS=m
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V4 is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V4 is not set
# CONFIG_NFSD_TCP is not set
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_SUNRPC=m
# CONFIG_SUNRPC_GSS is not set
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_CIFS is not set
CONFIG_NCP_FS=m
CONFIG_NCPFS_PACKET_SIGNING=y
CONFIG_NCPFS_IOCTL_LOCKING=y
CONFIG_NCPFS_STRONG=y
CONFIG_NCPFS_NFS_NS=y
CONFIG_NCPFS_OS2_NS=y
CONFIG_NCPFS_SMALLDOS=y
CONFIG_NCPFS_NLS=y
CONFIG_NCPFS_EXTRAS=y
CONFIG_CODA_FS=m
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
CONFIG_MAC_PARTITION=y
CONFIG_MSDOS_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
# CONFIG_NEC98_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
#
# Graphics support
#
CONFIG_FB=y
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=y
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
CONFIG_FB_HGA=m
CONFIG_FB_RIVA=m
# CONFIG_FB_I810 is not set
# CONFIG_FB_MATROX is not set
CONFIG_FB_RADEON=m
CONFIG_FB_ATY128=m
CONFIG_FB_ATY=m
CONFIG_FB_ATY_CT=y
CONFIG_FB_ATY_GX=y
# CONFIG_FB_ATY_XL_INIT is not set
CONFIG_FB_SIS=m
CONFIG_FB_SIS_300=y
CONFIG_FB_SIS_315=y
CONFIG_FB_NEOMAGIC=m
CONFIG_FB_3DFX=m
CONFIG_FB_VOODOO1=m
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE is not set
#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
#
# Sound
#
CONFIG_SOUND=m
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_SEQUENCER=m
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=m
CONFIG_SND_VERBOSE_PRINTK=y
# CONFIG_SND_DEBUG is not set
#
# Generic devices
#
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
CONFIG_SND_MPU401=m
#
# ISA devices
#
CONFIG_SND_AD1816A=m
CONFIG_SND_AD1848=m
CONFIG_SND_CS4231=m
# CONFIG_SND_CS4232 is not set
# CONFIG_SND_CS4236 is not set
CONFIG_SND_ES968=m
CONFIG_SND_ES1688=m
CONFIG_SND_ES18XX=m
# CONFIG_SND_GUSCLASSIC is not set
# CONFIG_SND_GUSEXTREME is not set
# CONFIG_SND_GUSMAX is not set
# CONFIG_SND_INTERWAVE is not set
# CONFIG_SND_INTERWAVE_STB is not set
CONFIG_SND_OPTI92X_AD1848=m
CONFIG_SND_OPTI92X_CS4231=m
CONFIG_SND_OPTI93X=m
# CONFIG_SND_SB8 is not set
CONFIG_SND_SB16=m
CONFIG_SND_SBAWE=m
CONFIG_SND_SB16_CSP=y
# CONFIG_SND_WAVEFRONT is not set
# CONFIG_SND_ALS100 is not set
# CONFIG_SND_AZT2320 is not set
CONFIG_SND_CMI8330=m
# CONFIG_SND_DT019X is not set
CONFIG_SND_OPL3SA2=m
# CONFIG_SND_SGALAXY is not set
#
# PCI devices
#
CONFIG_SND_ALI5451=m
CONFIG_SND_CS46XX=m
# CONFIG_SND_CS46XX_NEW_DSP is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
CONFIG_SND_CMIPCI=m
CONFIG_SND_ENS1370=m
CONFIG_SND_ENS1371=m
CONFIG_SND_ES1938=m
CONFIG_SND_ES1968=m
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_SONICVIBES is not set
CONFIG_SND_VIA82XX=m
#
# ALSA USB devices
#
CONFIG_SND_USB_AUDIO=m
#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
#
# USB support
#
CONFIG_USB=m
CONFIG_USB_DEBUG=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_UHCI_HCD=m
#
# USB Device Class drivers
#
CONFIG_USB_AUDIO=m
# CONFIG_USB_BLUETOOTH_TTY is not set
CONFIG_USB_MIDI=m
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
CONFIG_USB_STORAGE=m
CONFIG_USB_STORAGE_DEBUG=y
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_HP8200e=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y
#
# USB Human Interface Devices (HID)
#
CONFIG_USB_HID=m
# CONFIG_USB_HIDINPUT is not set
# CONFIG_USB_HIDDEV is not set
#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
CONFIG_USB_AIPTEK=m
CONFIG_USB_WACOM=m
# CONFIG_USB_KBTAB is not set
CONFIG_USB_POWERMATE=m
# CONFIG_USB_XPAD is not set
#
# USB Imaging devices
#
CONFIG_USB_MDC800=m
CONFIG_USB_SCANNER=m
CONFIG_USB_MICROTEK=m
CONFIG_USB_HPUSBSCSI=m
#
# USB Multimedia devices
#
CONFIG_USB_DABUSB=m
CONFIG_USB_VICAM=m
CONFIG_USB_DSBR=m
CONFIG_USB_IBMCAM=m
# CONFIG_USB_KONICAWC is not set
CONFIG_USB_OV511=m
CONFIG_USB_PWC=m
CONFIG_USB_SE401=m
CONFIG_USB_STV680=m
#
# USB Network adaptors
#
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
#
# USB Host-to-Host Cables
#
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_GENESYS=y
CONFIG_USB_NET1080=y
CONFIG_USB_PL2301=y
#
# Intelligent USB Devices/Gadgets
#
CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_ZAURUS=y
CONFIG_USB_CDCETHER=y
#
# USB port drivers
#
CONFIG_USB_USS720=m
#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=m
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_BELKIN=m
CONFIG_USB_SERIAL_WHITEHEAT=m
CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
CONFIG_USB_SERIAL_EMPEG=m
CONFIG_USB_SERIAL_FTDI_SIO=m
CONFIG_USB_SERIAL_VISOR=m
CONFIG_USB_SERIAL_IPAQ=m
CONFIG_USB_SERIAL_IR=m
CONFIG_USB_SERIAL_EDGEPORT=m
CONFIG_USB_SERIAL_EDGEPORT_TI=m
CONFIG_USB_SERIAL_KEYSPAN_PDA=m
CONFIG_USB_SERIAL_KEYSPAN=m
# CONFIG_USB_SERIAL_KEYSPAN_MPR is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28X is not set
CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
# CONFIG_USB_SERIAL_KEYSPAN_USA19 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA18X is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19W is not set
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
# CONFIG_USB_SERIAL_KEYSPAN_USA49W is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA49WLC is not set
CONFIG_USB_SERIAL_KLSI=m
CONFIG_USB_SERIAL_KOBIL_SCT=m
CONFIG_USB_SERIAL_MCT_U232=m
CONFIG_USB_SERIAL_PL2303=m
# CONFIG_USB_SERIAL_SAFE is not set
CONFIG_USB_SERIAL_CYBERJACK=m
CONFIG_USB_SERIAL_XIRCOM=m
CONFIG_USB_SERIAL_OMNINET=m
CONFIG_USB_EZUSB=y
#
# USB Miscellaneous drivers
#
CONFIG_USB_EMI26=m
CONFIG_USB_TIGL=m
CONFIG_USB_AUERSWALD=m
CONFIG_USB_RIO500=m
CONFIG_USB_BRLVGER=m
CONFIG_USB_LCD=m
# CONFIG_USB_TEST is not set
#
# Bluetooth support
#
# CONFIG_BT is not set
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_STACKOVERFLOW=y
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_IOVIRT is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_HIGHMEM is not set
# CONFIG_KALLSYMS is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_FRAME_POINTER is not set
CONFIG_X86_EXTRA_IRQS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
#
# Security options
#
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
#
# Library routines
#
# CONFIG_CRC32 is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_X86_BIOS_REBOOT=y
#
# Hardware Abstraction Layer
#
On 24 May 2003 00:02:30 -0400, John Shillinglaw wrote:
>Anyway I get not found messages when redhat modprobes char-major-10-1,
>eth1, etc. when it boots up. This seems to be related to aliases since
>eth1 is aliased to sis900 and char-major-10-1 to psaux. All help greatly
>appreciated... exact details and .config file below:
...
>I also tried to run the generate modprobe.conf script with no changes to
>the behavior.
Did you install the generated modprobe.conf in /etc? If not, do so.
rc.sysinit has a known problem that causes it to disable module
autoloading in 2.5 kernels. Fixed by the patch below.
mkinitrd generally doesn't work with 2.5 modules, or once the new
module-init-tools have been installed. I don't know how to fix
that; maybe an LKML archive search will find something.
--- /etc/rc.d/rc.sysinit~ 2003-02-24 22:54:17.000000000 +0100
+++ /etc/rc.d/rc.sysinit 2003-05-01 17:07:09.000000000 +0200
@@ -357,7 +357,7 @@
IN_INITLOG=
fi
-if ! LC_ALL=C grep -iq nomodules /proc/cmdline 2>/dev/null && [ -f /proc/ksyms ]; then
+if ! LC_ALL=C grep -iq nomodules /proc/cmdline 2>/dev/null && [ -f /proc/modules ]; then
USEMODULES=y
fi
Thanks again,
My only real problem now seems to be that while X loads like it's
supposed to, my mouse ( generic ps/2 wheel mouse ) doesn't move once X
has started.
Only other problems were a message about keybdev being not found which I
understand is normal, and a usb-ohci not found error which hopefully I
found the missing config setting for.
If I can just figure out why the mouse doesn't work, I'll be running on
2.5.69
Thanks again
On Sat, 2003-05-24 at 06:14, [email protected] wrote:
> On 24 May 2003 00:02:30 -0400, John Shillinglaw wrote:
> >Anyway I get not found messages when redhat modprobes char-major-10-1,
> >eth1, etc. when it boots up. This seems to be related to aliases since
> >eth1 is aliased to sis900 and char-major-10-1 to psaux. All help greatly
> >appreciated... exact details and .config file below:
> ...
> >I also tried to run the generate modprobe.conf script with no changes to
> >the behavior.
>
> Did you install the generated modprobe.conf in /etc? If not, do so.
>
> rc.sysinit has a known problem that causes it to disable module
> autoloading in 2.5 kernels. Fixed by the patch below.
>
> mkinitrd generally doesn't work with 2.5 modules, or once the new
> module-init-tools have been installed. I don't know how to fix
> that; maybe an LKML archive search will find something.
>
> --- /etc/rc.d/rc.sysinit~ 2003-02-24 22:54:17.000000000 +0100
> +++ /etc/rc.d/rc.sysinit 2003-05-01 17:07:09.000000000 +0200
> @@ -357,7 +357,7 @@
> IN_INITLOG=
> fi
>
> -if ! LC_ALL=C grep -iq nomodules /proc/cmdline 2>/dev/null && [ -f /proc/ksyms ]; then
> +if ! LC_ALL=C grep -iq nomodules /proc/cmdline 2>/dev/null && [ -f /proc/modules ]; then
> USEMODULES=y
> fi
>
>