hello,
i am sorry for asking you but i am a newbie:(...
i have a acer tm613txv nb, kernel 2.4.22
i would like to turn on dma on hhd but i get this message
/dev/hda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
when i use a kernel 2.4.20-8 that works fine
somewhere i founded that problem could be in driver Uniform Multi-Platform E-IDE
driver Revision: 7.00beta4-2.4 which is in 2.4.22, but i dont know how shoud i
solve this problem..thank you for every advice....(i think that i have compiled
everthing what i shoud)
jirka
icq52736508
lspci:
00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory
Controller Hub (rev 11)
00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics
Controller] (rev 11)
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 03)
00:1f.0 ISA bridge: Intel Corp. 82801BAM ISA Bridge (LPC) (rev 03)
00:1f.1 IDE interface: Intel Corp. 82801BAM IDE U100 (rev 03)
messages:
Sep 8 18:47:57 pepek kernel: Uniform Multi-Platform E-IDE driver
Revision: 7.00beta4-2.4
Sep 8 18:47:57 pepek kernel: ide: Assuming 33MHz system bus speed for
PIO modes; override with idebus=xx
Sep 8 18:47:57 pepek kernel: hda: IBM-DJSA-220, ATA DISK drive
Sep 8 18:47:57 pepek kernel: hdc: UJDA710, ATAPI CD/DVD-ROM drive
Sep 8 18:47:57 pepek kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Sep 8 18:47:57 pepek kernel: ide1 at 0x170-0x177,0x376 on irq 15
Sep 8 18:47:57 pepek kernel: hda: attached ide-disk driver.
Sep 8 18:47:57 pepek kernel: hda: host protected area => 1
Sep 8 18:47:57 pepek kernel: hda: 39070080 sectors (20004 MB)
w/1874KiB
Cache, CHS=2432/255/63
hdparm -iv:
Model=IBM-DJSA-220, FwRev=JS4OAC7A, SerialNo=44T44W45916
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=1874kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=39070080
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 *udma4
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: 2 3 4 5
On Wednesday 10 of September 2003 11:52, [email protected] wrote:
> when i use a kernel 2.4.20-8 that works fine
> somewhere i founded that problem could be in driver Uniform Multi-Platform
> E-IDE driver Revision: 7.00beta4-2.4 which is in 2.4.22, but i dont know
> how shoud i solve this problem..thank you for every advice....(i think that
> i have compiled everthing what i shoud)
You don't have support for you IDE chipset compiled in the kernel.
You should add something like "CONFIG_BLK_DEV_PIIX=y" to your .config file.
This issue was discussed several times on lkml,
please search archives for more info.
--bartlomiej