Zaurus keyboard driver updates:
* Change the scan interval from 100ms to 50ms. This stops the key
repeat from triggering on double letter presses.
* Remove unneeded stale hinge code from corgikbd
* Change unneeded corgi GPIO pins to inputs when suspended
* Add support for the headphone jack switch for both corgi and spitz
(as switch SW_2)
Signed-off-by: Richard Purdie <[email protected]>
Index: linux-2.6.15/drivers/input/keyboard/corgikbd.c
===================================================================
--- linux-2.6.15.orig/drivers/input/keyboard/corgikbd.c 2006-03-04 23:08:30.000000000 +0000
+++ linux-2.6.15/drivers/input/keyboard/corgikbd.c 2006-03-04 23:10:07.000000000 +0000
@@ -29,11 +29,11 @@
#define KB_COLS 12
#define KB_ROWMASK(r) (1 << (r))
#define SCANCODE(r,c) ( ((r)<<4) + (c) + 1 )
-/* zero code, 124 scancodes + 3 hinge combinations */
-#define NR_SCANCODES ( SCANCODE(KB_ROWS-1,KB_COLS-1) +1 +1 +3 )
-#define SCAN_INTERVAL (HZ/10)
+/* zero code, 124 scancodes */
+#define NR_SCANCODES ( SCANCODE(KB_ROWS-1,KB_COLS-1) +1 +1 )
-#define HINGE_SCAN_INTERVAL (HZ/4)
+#define SCAN_INTERVAL (50) /* ms */
+#define HINGE_SCAN_INTERVAL (250) /* ms */
#define CORGI_KEY_CALENDER KEY_F1
#define CORGI_KEY_ADDRESS KEY_F2
@@ -49,9 +49,6 @@
#define CORGI_KEY_MAIL KEY_F10
#define CORGI_KEY_OK KEY_F11
#define CORGI_KEY_MENU KEY_F12
-#define CORGI_HINGE_0 KEY_KP0
-#define CORGI_HINGE_1 KEY_KP1
-#define CORGI_HINGE_2 KEY_KP2
static unsigned char corgikbd_keycode[NR_SCANCODES] = {
0, /* 0 */
@@ -63,7 +60,6 @@
CORGI_KEY_MAIL, KEY_Z, KEY_X, KEY_MINUS, KEY_SPACE, KEY_COMMA, 0, KEY_UP, 0, 0, 0, CORGI_KEY_FN, 0, 0, 0, 0, /* 81-96 */
KEY_SYSRQ, CORGI_KEY_JAP1, CORGI_KEY_JAP2, CORGI_KEY_CANCEL, CORGI_KEY_OK, CORGI_KEY_MENU, KEY_LEFT, KEY_DOWN, KEY_RIGHT, 0, 0, 0, 0, 0, 0, 0, /* 97-112 */
CORGI_KEY_OFF, CORGI_KEY_EXOK, CORGI_KEY_EXCANCEL, CORGI_KEY_EXJOGDOWN, CORGI_KEY_EXJOGUP, 0, 0, 0, 0, 0, 0, 0, /* 113-124 */
- CORGI_HINGE_0, CORGI_HINGE_1, CORGI_HINGE_2 /* 125-127 */
};
@@ -187,7 +183,7 @@
/* if any keys are pressed, enable the timer */
if (num_pressed)
- mod_timer(&corgikbd_data->timer, jiffies + SCAN_INTERVAL);
+ mod_timer(&corgikbd_data->timer, jiffies + msecs_to_jiffies(SCAN_INTERVAL));
spin_unlock_irqrestore(&corgikbd_data->lock, flags);
}
@@ -228,6 +224,7 @@
* 0x0c - Keyboard and Screen Closed
*/
+#define READ_GPIO_BIT(x) (GPLR(x) & GPIO_bit(x))
#define HINGE_STABLE_COUNT 2
static int sharpsl_hinge_state;
static int hinge_count;
@@ -239,6 +236,7 @@
unsigned long flags;
gprr = read_scoop_reg(&corgiscoop_device.dev, SCOOP_GPRR) & (CORGI_SCP_SWA | CORGI_SCP_SWB);
+ gprr |= (READ_GPIO_BIT(CORGI_GPIO_AK_INT) != 0);
if (gprr != sharpsl_hinge_state) {
hinge_count = 0;
sharpsl_hinge_state = gprr;
@@ -249,27 +247,38 @@
input_report_switch(corgikbd_data->input, SW_0, ((sharpsl_hinge_state & CORGI_SCP_SWA) != 0));
input_report_switch(corgikbd_data->input, SW_1, ((sharpsl_hinge_state & CORGI_SCP_SWB) != 0));
+ input_report_switch(corgikbd_data->input, SW_2, (READ_GPIO_BIT(CORGI_GPIO_AK_INT) != 0));
input_sync(corgikbd_data->input);
spin_unlock_irqrestore(&corgikbd_data->lock, flags);
}
}
- mod_timer(&corgikbd_data->htimer, jiffies + HINGE_SCAN_INTERVAL);
+ mod_timer(&corgikbd_data->htimer, jiffies + msecs_to_jiffies(HINGE_SCAN_INTERVAL));
}
#ifdef CONFIG_PM
static int corgikbd_suspend(struct platform_device *dev, pm_message_t state)
{
+ int i;
struct corgikbd *corgikbd = platform_get_drvdata(dev);
+
corgikbd->suspended = 1;
+ /* strobe 0 is the power key so this can't be made an input for
+ powersaving therefore i = 1 */
+ for (i = 1; i < CORGI_KEY_STROBE_NUM; i++)
+ pxa_gpio_mode(CORGI_GPIO_KEY_STROBE(i) | GPIO_IN);
return 0;
}
static int corgikbd_resume(struct platform_device *dev)
{
+ int i;
struct corgikbd *corgikbd = platform_get_drvdata(dev);
+ for (i = 1; i < CORGI_KEY_STROBE_NUM; i++)
+ pxa_gpio_mode(CORGI_GPIO_KEY_STROBE(i) | GPIO_OUT | GPIO_DFLT_HIGH);
+
/* Upon resume, ignore the suspend key for a short while */
corgikbd->suspend_jiffies=jiffies;
corgikbd->suspended = 0;
@@ -333,10 +342,11 @@
clear_bit(0, input_dev->keybit);
set_bit(SW_0, input_dev->swbit);
set_bit(SW_1, input_dev->swbit);
+ set_bit(SW_2, input_dev->swbit);
input_register_device(corgikbd->input);
- mod_timer(&corgikbd->htimer, jiffies + HINGE_SCAN_INTERVAL);
+ mod_timer(&corgikbd->htimer, jiffies + msecs_to_jiffies(HINGE_SCAN_INTERVAL));
/* Setup sense interrupts - RisingEdge Detect, sense lines as inputs */
for (i = 0; i < CORGI_KEY_SENSE_NUM; i++) {
@@ -351,6 +361,9 @@
for (i = 0; i < CORGI_KEY_STROBE_NUM; i++)
pxa_gpio_mode(CORGI_GPIO_KEY_STROBE(i) | GPIO_OUT | GPIO_DFLT_HIGH);
+ /* Setup the headphone jack as an input */
+ pxa_gpio_mode(CORGI_GPIO_AK_INT | GPIO_IN);
+
return 0;
}
Index: linux-2.6.15/drivers/input/keyboard/spitzkbd.c
===================================================================
--- linux-2.6.15.orig/drivers/input/keyboard/spitzkbd.c 2006-03-04 23:08:30.000000000 +0000
+++ linux-2.6.15/drivers/input/keyboard/spitzkbd.c 2006-03-04 23:09:06.000000000 +0000
@@ -30,6 +30,7 @@
#define SCANCODE(r,c) (((r)<<4) + (c) + 1)
#define NR_SCANCODES ((KB_ROWS<<4) + 1)
+#define SCAN_INTERVAL (50) /* ms */
#define HINGE_SCAN_INTERVAL (150) /* ms */
#define SPITZ_KEY_CALENDER KEY_F1
@@ -230,7 +231,7 @@
/* if any keys are pressed, enable the timer */
if (num_pressed)
- mod_timer(&spitzkbd_data->timer, jiffies + msecs_to_jiffies(100));
+ mod_timer(&spitzkbd_data->timer, jiffies + msecs_to_jiffies(SCAN_INTERVAL));
spin_unlock_irqrestore(&spitzkbd_data->lock, flags);
}
@@ -287,6 +288,7 @@
unsigned long flags;
state = GPLR(SPITZ_GPIO_SWA) & (GPIO_bit(SPITZ_GPIO_SWA)|GPIO_bit(SPITZ_GPIO_SWB));
+ state |= (GPLR(SPITZ_GPIO_AK_INT) & GPIO_bit(SPITZ_GPIO_AK_INT));
if (state != sharpsl_hinge_state) {
hinge_count = 0;
sharpsl_hinge_state = state;
@@ -299,6 +301,7 @@
input_report_switch(spitzkbd_data->input, SW_0, ((GPLR(SPITZ_GPIO_SWA) & GPIO_bit(SPITZ_GPIO_SWA)) != 0));
input_report_switch(spitzkbd_data->input, SW_1, ((GPLR(SPITZ_GPIO_SWB) & GPIO_bit(SPITZ_GPIO_SWB)) != 0));
+ input_report_switch(spitzkbd_data->input, SW_2, ((GPLR(SPITZ_GPIO_AK_INT) & GPIO_bit(SPITZ_GPIO_AK_INT)) != 0));
input_sync(spitzkbd_data->input);
spin_unlock_irqrestore(&spitzkbd_data->lock, flags);
@@ -397,6 +400,7 @@
clear_bit(0, input_dev->keybit);
set_bit(SW_0, input_dev->swbit);
set_bit(SW_1, input_dev->swbit);
+ set_bit(SW_2, input_dev->swbit);
input_register_device(input_dev);
@@ -432,6 +436,9 @@
request_irq(SPITZ_IRQ_GPIO_SWB, spitzkbd_hinge_isr,
SA_INTERRUPT | SA_TRIGGER_RISING | SA_TRIGGER_FALLING,
"Spitzkbd SWB", spitzkbd);
+ request_irq(SPITZ_IRQ_GPIO_AK_INT, spitzkbd_hinge_isr,
+ SA_INTERRUPT | SA_TRIGGER_RISING | SA_TRIGGER_FALLING,
+ "Spitzkbd HP", spitzkbd);
printk(KERN_INFO "input: Spitz Keyboard Registered\n");
@@ -450,6 +457,7 @@
free_irq(SPITZ_IRQ_GPIO_ON_KEY, spitzkbd);
free_irq(SPITZ_IRQ_GPIO_SWA, spitzkbd);
free_irq(SPITZ_IRQ_GPIO_SWB, spitzkbd);
+ free_irq(SPITZ_IRQ_GPIO_AK_INT, spitzkbd);
del_timer_sync(&spitzkbd->htimer);
del_timer_sync(&spitzkbd->timer);
On Sunday 05 March 2006 04:51, Richard Purdie wrote:
> Zaurus keyboard driver updates:
> * Change the scan interval from 100ms to 50ms. This stops the key
> repeat from triggering on double letter presses.
> * Remove unneeded stale hinge code from corgikbd
> * Change unneeded corgi GPIO pins to inputs when suspended
> * Add support for the headphone jack switch for both corgi and spitz
> (as switch SW_2)
>
> Signed-off-by: Richard Purdie <[email protected]>
>
Applied to the input tree, thank you Richard.
--
Dmitry