On Tue, 2007-07-31 at 17:45 -0700, Andrew Morton wrote:
> On Tue, 31 Jul 2007 11:28:32 +0200 "Joachim Deguara"
> <[email protected]> wrote:
>
> > On my Acer Ferrari 1000 the tg3 ethernet no longer is available
> after a
> > suspend to ram with the latet 2.6.23-rc1-git9.
It seems to work for me on the same 2.6.23-rc1-git9 kernel with the same
tg3 hardware. Can you narrow down the problem some more? It seems that
in your case, the chip registers are returning 0xffffffff after resume.
Can you do lspci -xxxvvv on the tg3 adapter after resume?
Here's my log:
tg3.c:v3.79 (July 18, 2007)
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
eth0: Tigon3 [partno(BCM95755m) rev a002 PHY(5755)] (PCI Express) 10/100/1000Ba1eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:40:00.0[A] -> GSI 17 (level, low) -> IRQ 17
eth1: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCI Express) 10/100/1000Bas5eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 18 (level, low) -> IRQ 19
eth2: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/1008eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
eth2: dma_rwctrl[763f0000] dma_mask[32-bit]
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
ADDRCONF(NETDEV_UP): eth2: link is not ready
tg3: eth2: Link is up at 1000 Mbps, full duplex.
tg3: eth2: Flow control is on for TX and on for RX.
ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
Stopping tasks ... done.
Suspending console(s)
ACPI handle has no context!
pnp: Device 00:08 disabled.
ACPI handle has no context!
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
tg3: eth2: Link is down.
pnp: Device 00:08 activated.
Restarting tasks ... hda: status error: status=0x51 { DriveReady SeekComplete E}hda: status error: error=0x04 { DriveStatusError }
ide: failed opcode was: unknown
hda: no DRQ after issuing MULTWRITE_EXT
hda: status error: status=0x51 { DriveReady SeekComplete Error }
hda: status error: error=0x04 { DriveStatusError }
ide: failed opcode was: unknown
hda: no DRQ after issuing MULTWRITE_EXT
hda: status error: status=0x51 { DriveReady SeekComplete Error }
hda: status error: error=0x04 { DriveStatusError }
ide: failed opcode was: unknown
hda: no DRQ after issuing MULTWRITE_EXT
hda: status error: status=0x51 { DriveReady SeekComplete Error }
hda: status error: error=0x04 { DriveStatusError }
ide: failed opcode was: unknown
hda: no DRQ after issuing MULTWRITE_EXT
done.
ide0: reset: success
tg3: eth2: Link is up at 1000 Mbps, full duplex.
tg3: eth2: Flow control is on for TX and on for RX.
On Wednesday 01 August 2007 09:53:31 Michael Chan wrote:
> On Tue, 2007-07-31 at 17:45 -0700, Andrew Morton wrote:
> > On Tue, 31 Jul 2007 11:28:32 +0200 "Joachim Deguara"
> >
> > <[email protected]> wrote:
> > > On my Acer Ferrari 1000 the tg3 ethernet no longer is available
> >
> > after a
> >
> > > suspend to ram with the latet 2.6.23-rc1-git9.
>
> It seems to work for me on the same 2.6.23-rc1-git9 kernel with the same
> tg3 hardware. Can you narrow down the problem some more? It seems that
> in your case, the chip registers are returning 0xffffffff after resume.
> Can you do lspci -xxxvvv on the tg3 adapter after resume?
Here are the lspci outputs for the tg3
Before
07:00.0 Network controller: Broadcom Corporation Unknown device 4328 (rev 01)
Subsystem: AMBIT Microsystem Corp. Unknown device 0319
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0200000 (64-bit, non-prefetchable) [disabled] [size=16K]
Region 2: Memory at d8000000 (64-bit, prefetchable) [disabled] [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM unknown, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [15c] Power Budgeting
00: e4 14 28 43 00 00 10 00 01 00 80 02 00 00 00 00
10: 04 00 20 d0 00 00 00 00 0c 00 00 d8 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 68 14 19 03
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
40: 01 58 02 06 00 40 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 05 d0 80 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 10 00 18 00 00 00 00 01 00 00 00 03 00 00 00
90: 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 10 00 01 00 a0 0f 64 00 00 00 1a 00 11 60 03 00
e0: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
and after s2ram:
07:00.0 Network controller: Broadcom Corporation Unknown device 4328 (rev 01)
Subsystem: AMBIT Microsystem Corp. Unknown device 0319
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0200000 (64-bit, non-prefetchable) [disabled] [size=16K]
Region 2: Memory at d8000000 (64-bit, prefetchable) [disabled] [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM unknown, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [15c] Power Budgeting
00: e4 14 28 43 00 00 10 00 01 00 80 02 00 00 00 00
10: 04 00 20 d0 00 00 00 00 0c 00 00 d8 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 68 14 19 03
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
40: 01 58 02 06 00 40 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 05 d0 80 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 10 00 18 00 00 00 00 01 00 00 00 03 00 00 00
90: 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 10 00 01 00 a0 0f 00 00 00 00 11 00 11 60 03 00
e0: 00 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Using diff I see there are some differences, what they mean I will leave that
to your expertise ;)
Thanks
-Joachim
Full outputs below
Before
--------
00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 64
00: 02 10 50 59 06 00 20 22 10 00 00 06 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 c4 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 42 20 05 00
50: 25 10 0e 01 00 00 00 00 00 00 00 00 00 00 00 00
60: 4f 00 00 00 00 00 00 00 00 00 00 00 2c 00 73 06
70: e0 08 00 00 00 00 00 00 20 4e 00 00 00 00 00 10
80: 10 10 00 02 94 14 00 03 20 00 00 00 22 21 00 10
90: 00 00 00 7c 45 cc 45 ed 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 08 00 80 01 60 20 11 11 d0 00 00 00
d0: 25 05 65 00 02 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 7f 00 00 00 00 00 00 00
f0: 00 00 00 00 00 80 80 00 00 00 00 00 00 00 48 01
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d0100000-d01fffff
Prefetchable memory behind bridge: 00000000d4000000-00000000d7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [44] HyperTransport: MSI Mapping
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
00: 02 10 3f 5a 07 00 30 02 00 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 91 91 20 02
20: 10 d0 10 d0 01 d4 f1 d7 00 00 00 00 00 00 00 00
30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 0c 00
40: 20 00 00 40 08 b0 03 a8 00 00 00 00 25 10 0e 01
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d 00 00 00 25 10 0e 01 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
00: 02 10 36 5a 04 00 10 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 03 c8 00 00 00 00 10 80 41 01 20 00 00 00
60: 10 08 00 00 11 0c 00 f7 02 00 01 11 60 00 00 00
70: c0 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d b8 00 00 25 10 0e 01 08 00 03 a8 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: a0 00 00 00 ff 00 00 c0 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:05.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=03, subordinate=05, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled RCB 64 bytes Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
00: 02 10 37 5a 04 00 10 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 03 05 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 03 c8 00 00 00 00 10 80 41 01 20 00 00 00
60: 10 08 00 00 11 0c 00 f7 12 00 01 11 60 00 00 00
70: c0 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d b8 00 00 25 10 0e 01 08 00 03 a8 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: a0 00 00 00 ff 00 00 c0 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:06.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
00: 02 10 38 5a 04 00 10 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 06 06 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 03 c8 00 00 00 00 10 80 41 01 20 00 00 00
60: 10 08 00 00 11 0c 00 f7 02 00 01 11 60 00 00 00
70: c0 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d b8 00 00 25 10 0e 01 08 00 03 a8 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: a0 00 00 00 ff 00 00 c0 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d0200000-d02fffff
Prefetchable memory behind bridge: 00000000d8000000-00000000d80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
00: 02 10 39 5a 06 00 10 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 07 07 00 f1 01 00 20
20: 20 d0 20 d0 01 d8 01 d8 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 03 c8 00 00 00 00 10 80 41 01 20 00 00 00
60: 10 08 00 00 11 0c 00 04 40 00 11 10 e0 0c 00 00
70: c0 03 48 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 80 00 10 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d b8 00 00 25 10 0e 01 08 00 03 a8 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: a0 00 00 00 ff 00 00 c0 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:12.0 IDE interface: ATI Technologies Inc 4379 Serial ATA Controller (rev
80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 8440 [size=8]
Region 1: I/O ports at 8430 [size=4]
Region 2: I/O ports at 8420 [size=8]
Region 3: I/O ports at 8410 [size=4]
Region 4: I/O ports at 8400 [size=16]
Region 5: Memory at d0004000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at 8c000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00: 02 10 79 43 07 00 b0 02 80 8f 01 01 08 40 00 00
10: 41 84 00 00 31 84 00 00 21 84 00 00 11 84 00 00
20: 01 84 00 00 00 40 00 d0 00 00 00 00 25 10 0e 01
30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 00 00
40: 18 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 05 00 00 00 00 00 00 00 00 00 00 00 0e b7 00 00
60: 01 50 22 06 00 40 00 64 02 10 00 00 00 00 00 00
70: 08 00 60 00 00 80 f9 37 00 00 60 00 00 00 00 00
80: 03 00 00 00 22 00 00 00 00 00 01 00 b4 b2 f1 59
90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
a0: 01 21 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40
b0: 01 21 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40
c0: 00 00 00 00 ff ff ff ff 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0005000 (32-bit, non-prefetchable) [size=4K]
00: 02 10 74 43 17 00 a0 02 80 10 03 0c 10 40 80 00
10: 00 50 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
40: 80 00 00 00 00 00 00 00 00 00 00 00 10 00 00 00
50: 40 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0006000 (32-bit, non-prefetchable) [size=4K]
00: 02 10 75 43 17 00 a0 02 80 10 03 0c 10 40 00 00
10: 00 60 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
40: 80 00 00 00 00 00 00 00 00 00 00 00 10 00 00 00
50: 40 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller
(rev 80) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0007000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
00: 02 10 73 43 17 00 b0 02 80 20 03 0c 10 40 00 00
10: 00 70 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 00 00
40: 80 00 00 00 00 00 00 00 00 00 00 00 10 00 00 00
50: 42 28 e0 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 20 00 00 00 20 00 00 00 20 00 00 00 20 00 00
70: 00 20 00 00 00 20 00 00 00 20 00 00 00 20 00 00
80: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 01 00 00 01 00 00 08 80 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 7e
e0: 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 83)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Region 0: I/O ports at 8450 [size=16]
Region 1: Memory at d0004400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [b0] HyperTransport: MSI Mapping
00: 02 10 72 43 03 00 30 02 83 00 05 0c 00 00 80 00
10: 51 84 00 00 00 44 00 d0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 b0 00 00 00 00 00 00 00 00 00 00 00
40: d4 bb 00 00 00 00 00 00 0f ff 00 00 00 00 00 00
50: ff 03 00 00 df 03 e4 00 00 00 00 00 00 00 00 00
60: 01 00 07 00 9f b1 9e 8f 00 90 00 00 20 00 00 00
70: 00 01 00 00 08 00 c0 fe ff 4e 00 00 00 00 00 00
80: 07 01 00 00 00 00 00 00 00 00 00 00 00 b0 0d 7a
90: 51 84 00 00 f9 ce ff 00 00 00 00 00 00 00 00 00
a0: 00 00 ff ff 00 00 00 00 08 37 0a 00 c0 09 00 f9
b0: 08 00 02 a8 00 00 00 00 00 00 00 00 f0 0f 13 01
c0: 7d db b6 ed 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: d8 0c 00 00 00 81 00 00 00 00 00 00 0a 00 38 01
00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
Controller (rev 80) (prog-if 80 [Master])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 8460 [size=16]
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00: 02 10 76 43 15 00 30 02 80 80 01 01 00 40 00 00
10: 81 84 00 00 75 84 00 00 79 84 00 00 71 84 00 00
20: 61 84 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 70 00 00 00 00 00 00 00 0b 01 00 00
40: 99 99 99 99 ff ff ff ff 01 01 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 40 01 1c 2c 46 18 01 00 00 00 ff 03 00 00
70: 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.2 Audio device: ATI Technologies Inc SB450 HDA Audio (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 7b 43 06 00 10 04 01 00 03 04 08 40 00 00
10: 04 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 00 00 00
40: 00 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00: 02 10 77 43 0f 00 20 02 80 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 04 00 00 00 ff 08 00 70 87 ff 20 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 68 00 00 00 0e 00 0f 00 f0 ff ff ff
70: 67 45 23 00 01 00 00 00 00 00 00 00 03 00 00 00
80: 08 00 03 a8 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
(prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=08, subordinate=09, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d0300000-d03fffff
Prefetchable memory behind bridge: 88000000-8bffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
00: 02 10 71 43 07 00 a0 02 80 01 04 06 00 40 81 00
10: 00 00 00 00 00 00 00 00 00 08 09 40 21 21 80 22
20: 30 d0 30 d0 00 88 f0 8b 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 26 00 30 ff 00 00 00 00 3c 01 3a f1 00 00 00 00
50: 01 00 00 00 08 00 03 a8 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 06
e0: 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
40: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
60: 00 00 01 00 e4 00 00 00 20 c8 2f 0f 30 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 08 00 01 21 20 a8 11 11 22 05 35 80 02 00 00 00
90: 5a 11 52 01 00 00 ff 00 07 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 03 00 00 00 00 00 7f 00 00 00 00 00 01 00 00 00
50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00
60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00
70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 03 00 d8 00 00 ff df 00 03 00 d4 00 80 ff d7 00
a0: 03 0a 00 00 00 0b 00 00 03 00 f0 00 00 ff ff 00
b0: 03 00 e0 00 80 ff ef 00 03 00 80 00 00 ff d3 00
c0: 00 00 00 00 00 00 00 00 13 10 00 00 00 f0 0f 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 03 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 00 00 00 01 01 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: e0 3e 78 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 46 00 00 00 00 00 00 00
80: 02 00 00 00 00 00 00 00 24 a2 68 5d 20 13 13 00
90: 20 0c 01 00 5a 80 10 67 39 00 00 80 00 00 00 00
a0: ed 06 00 5d 00 00 00 00 00 00 00 00 00 00 00 00
b0: e8 94 b5 24 3a 00 00 00 27 c2 31 c4 f8 ad 80 0f
c0: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 30 87 14 c1 30 82 50 a8 00 08 4d 88 43 03 40 e0
e0: 20 02 15 8f 61 42 00 c4 60 0a 0e 88 34 05 48 c4
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]
00: 22 10 03 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00
40: ff 3b 04 00 40 00 10 0a 00 00 00 00 00 00 00 00
50: 10 02 00 00 80 00 00 00 00 00 00 00 00 80 10 52
60: 1d 00 00 00 21 77 1f 00 c0 00 00 00 00 00 00 00
70: 11 01 32 51 21 40 70 50 00 2a 00 08 17 21 00 00
80: 31 33 07 33 13 31 13 31 00 00 00 00 00 00 00 00
90: 00 00 00 00 4f 0a 00 00 10 00 12 21 00 00 00 00
a0: 9e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 01 a7 0d 00 00 00 10 09 25 25 25 00
e0: 00 00 00 00 20 0e 63 00 01 17 00 00 00 00 00 00
f0: 0f 00 10 00 00 04 00 00 02 00 00 00 82 0f 04 00
01:05.0 VGA compatible controller: ATI Technologies Inc RS485 [Radeon Xpress
1100 IGP] (prog-if 00 [VGA])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at d0120000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 75 59 07 00 b0 02 00 00 00 03 08 42 00 00
10: 08 00 00 d4 01 90 00 00 00 00 10 d0 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 08 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
50: 01 00 02 06 00 00 00 00 02 50 20 00 30 02 00 4f
60: 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
07:00.0 Network controller: Broadcom Corporation Unknown device 4328 (rev 01)
Subsystem: AMBIT Microsystem Corp. Unknown device 0319
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0200000 (64-bit, non-prefetchable) [disabled] [size=16K]
Region 2: Memory at d8000000 (64-bit, prefetchable) [disabled] [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM unknown, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [15c] Power Budgeting
00: e4 14 28 43 00 00 10 00 01 00 80 02 00 00 00 00
10: 04 00 20 d0 00 00 00 00 0c 00 00 d8 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 68 14 19 03
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
40: 01 58 02 06 00 40 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 05 d0 80 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 10 00 18 00 00 00 00 01 00 00 00 03 00 00 00
90: 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 10 00 01 00 a0 0f 64 00 00 00 1a 00 11 60 03 00
e0: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
08:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit
Ethernet (rev 03)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (16000ns min)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d0300000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3
Enable-
Address: ffff6bfe7fffffb8 Data: fec7
00: e4 14 9c 16 06 00 b0 02 03 00 00 02 00 00 00 00
10: 00 00 30 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 07 00 00 00 25 10 0e 01
30: 00 00 ff ff 48 00 00 00 00 00 00 00 0a 01 40 00
40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 20 00 00
50: 03 58 fc 00 6f bf be 7f 05 00 86 00 b8 ff ff 7f
60: fe 6b ff ff c7 fe 00 00 98 00 03 30 00 00 3f 76
70: f6 10 00 00 20 00 00 80 14 04 00 00 00 00 00 00
80: 85 6b d0 36 03 40 00 0c 34 00 13 04 82 90 09 04
90: 09 97 00 01 00 00 00 00 00 00 00 00 eb 01 00 00
a0: 00 00 00 00 23 01 00 00 00 00 00 00 cb 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
08:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0314000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=08, secondary=09, subordinate=0c, sec-latency=176
Memory window 0: 88000000-8bfff000 (prefetchable)
Memory window 1: 90000000-93fff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite-
16-bit legacy interface ports at 0001
00: 4c 10 39 80 07 00 10 02 00 00 07 06 08 40 82 00
10: 00 40 31 d0 a0 00 00 02 08 09 0c b0 00 00 00 88
20: 00 f0 ff 8b 00 00 00 90 00 f0 ff 93 00 20 00 00
30: fc 20 00 00 00 24 00 00 fc 24 00 00 0b 01 c0 01
40: 25 10 0e 01 01 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 60 d0 44 08 19 00 d4 02 00 00 17 00 22 1b 72 01
90: c0 02 66 60 00 00 00 00 00 00 00 00 00 00 00 00
a0: 01 00 12 fe 00 00 c0 00 00 00 00 00 00 00 00 00
b0: 00 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 36 24 47 50 20 16 00 73 00 00 00 00 00 00 00 00
08:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE
1394 Host Controller (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at d0315000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0310000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00: 4c 10 3a 80 16 00 10 02 00 10 00 0c 08 40 80 00
10: 00 50 31 d0 00 00 31 d0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 02 03 04
40: 00 00 00 00 01 00 02 7e 00 80 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 00
f0: 00 08 00 00 82 10 00 00 25 10 0e 01 00 00 00 00
08:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card
Reader (SD/MMC/MS/MS PRO/xD)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0316000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 4c 10 3b 80 06 00 10 02 00 00 80 01 08 40 80 00
10: 00 60 31 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 07 04
40: 00 00 00 00 01 00 02 7e 00 00 00 00 00 00 00 00
50: 25 10 0e 01 05 01 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
After
------
00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 64
00: 02 10 50 59 06 00 20 22 10 00 00 06 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 c4 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 42 20 05 00
50: 25 10 0e 01 00 00 00 00 00 00 00 00 00 00 00 00
60: 87 00 00 00 0b 00 00 00 00 00 00 00 2c 00 73 06
70: e0 08 00 00 00 00 00 00 20 4e 00 00 00 00 00 10
80: 10 10 00 02 94 14 00 03 20 00 00 00 22 21 00 10
90: 00 00 00 7c 45 cc 45 ed 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 08 00 80 01 60 20 11 11 d0 00 00 00
d0: 25 05 65 00 02 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 80 80 00 00 00 00 00 00 00 48 01
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d0100000-d01fffff
Prefetchable memory behind bridge: 00000000d4000000-00000000d7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [44] HyperTransport: MSI Mapping
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
00: 02 10 3f 5a 07 00 30 02 00 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 40 91 91 20 22
20: 10 d0 10 d0 01 d4 f1 d7 00 00 00 00 00 00 00 00
30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 0c 00
40: 20 00 00 40 08 b0 03 a8 00 00 00 00 25 10 0e 01
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d 00 00 00 25 10 0e 01 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
00: 02 10 36 5a 04 00 10 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 03 c8 00 00 00 00 10 80 41 01 20 00 00 00
60: 10 08 00 00 11 0c 00 f7 02 00 01 11 00 00 00 00
70: c0 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d b8 00 00 25 10 0e 01 08 00 03 a8 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 02 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:05.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=03, subordinate=05, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
00: 02 10 37 5a 04 00 10 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 03 05 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 03 c8 00 00 00 00 10 80 41 01 20 00 00 00
60: 10 08 00 00 11 0c 00 f7 02 00 01 11 60 00 00 00
70: c0 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d b8 00 00 25 10 0e 01 08 00 03 a8 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 02 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:06.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
00: 02 10 38 5a 04 00 10 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 06 06 00 f1 01 00 00
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 03 c8 00 00 00 00 10 80 41 01 20 00 00 00
60: 10 08 00 00 11 0c 00 f7 02 00 01 11 00 00 00 00
70: c0 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d b8 00 00 25 10 0e 01 08 00 03 a8 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 02 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d0200000-d02fffff
Prefetchable memory behind bridge: 00000000d8000000-00000000d80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Acer Incorporated [ALI] Unknown device 010e
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
00: 02 10 39 5a 06 00 10 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 07 07 00 f1 01 00 00
20: 20 d0 20 d0 01 d8 01 d8 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 03 c8 00 00 00 00 10 80 41 01 20 00 00 00
60: 10 08 00 00 11 0c 00 04 02 00 11 10 00 00 00 00
70: c0 03 48 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 0d b8 00 00 25 10 0e 01 08 00 03 a8 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 02 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:12.0 IDE interface: ATI Technologies Inc 4379 Serial ATA Controller (rev
80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 8440 [size=8]
Region 1: I/O ports at 8430 [size=4]
Region 2: I/O ports at 8420 [size=8]
Region 3: I/O ports at 8410 [size=4]
Region 4: I/O ports at 8400 [size=16]
Region 5: Memory at d0004000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at 8c000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00: 02 10 79 43 07 00 b0 02 80 8f 01 01 08 40 00 00
10: 41 84 00 00 31 84 00 00 21 84 00 00 11 84 00 00
20: 01 84 00 00 00 40 00 d0 00 00 00 00 25 10 0e 01
30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 00 00
40: 18 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 05 00 00 00 00 00 00 00 00 00 00 00 0e b7 00 00
60: 01 50 22 06 00 40 00 64 02 10 00 00 00 00 00 00
70: 08 00 60 00 00 80 f9 37 00 00 60 00 00 00 00 00
80: 03 00 00 00 22 00 00 00 00 00 01 00 b4 b2 f1 59
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 01 21 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40
b0: 01 21 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0005000 (32-bit, non-prefetchable) [size=4K]
00: 02 10 74 43 17 00 a0 02 80 10 03 0c 10 40 80 00
10: 00 50 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
40: 80 00 00 00 00 00 00 00 00 00 00 00 10 00 00 00
50: 40 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(rev 80) (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0006000 (32-bit, non-prefetchable) [size=4K]
00: 02 10 75 43 17 00 a0 02 80 10 03 0c 10 40 00 00
10: 00 60 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
40: 80 00 00 00 00 00 00 00 00 00 00 00 10 00 00 00
50: 40 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller
(rev 80) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0007000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
00: 02 10 73 43 17 00 b0 02 80 20 03 0c 10 40 00 00
10: 00 70 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 00 00
40: 80 00 00 00 00 00 00 00 00 00 00 00 10 00 00 00
50: 42 28 e0 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 20 00 00 00 20 00 00 00 20 00 00 00 20 00 00
70: 00 20 00 00 00 20 00 00 00 20 00 00 00 20 00 00
80: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 01 00 01 01 00 20 08 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 7e
e0: 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 83)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Region 0: I/O ports at 8450 [size=16]
Region 1: Memory at d0004400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [b0] HyperTransport: MSI Mapping
00: 02 10 72 43 03 00 30 02 83 00 05 0c 00 00 80 00
10: 51 84 00 00 00 44 00 d0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 b0 00 00 00 00 00 00 00 00 00 00 00
40: d4 bb 00 00 00 00 00 00 0f ff 00 00 00 00 00 00
50: ff 03 00 00 df 03 e4 00 00 00 00 00 00 00 00 00
60: 01 00 07 00 9f b1 9e cf 00 90 00 00 20 00 00 00
70: 00 01 00 00 08 00 c0 fe ff 4e 00 00 00 00 00 00
80: 07 01 00 00 00 00 00 00 00 00 00 00 00 b0 0d 7a
90: 51 84 00 00 f9 ce ff 00 00 00 00 00 00 00 00 00
a0: 00 00 ff ff ff ff 00 00 08 37 0a 00 c0 29 00 f9
b0: 08 00 02 a8 00 00 00 00 00 00 00 00 f0 0f 13 01
c0: 7d db b6 ed 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: d8 0c 00 00 00 81 00 00 00 00 00 00 0a 00 18 01
00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
Controller (rev 80) (prog-if 82 [Master PriP])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 8460 [size=16]
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
00: 02 10 76 43 15 00 30 02 80 82 01 01 00 40 00 00
10: 81 84 00 00 75 84 00 00 79 84 00 00 71 84 00 00
20: 61 84 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 70 00 00 00 00 00 00 00 0b 01 00 00
40: 99 99 99 99 ff ff ff ff 00 01 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 40 01 10 2c 46 18 01 00 00 00 ff 03 00 00
70: 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.2 Audio device: ATI Technologies Inc SB450 HDA Audio (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 7b 43 06 00 10 04 01 00 03 04 08 40 00 00
10: 04 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 00 00 00
40: 00 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00: 02 10 77 43 0f 00 20 02 80 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 04 00 00 00 ff 08 00 70 87 ff 20 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 68 00 00 00 0e 00 0f 00 f0 ff ff ff
70: 67 45 23 00 01 00 00 00 00 00 00 00 03 00 00 00
80: 08 00 03 a8 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80)
(prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=08, subordinate=09, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d0300000-d03fffff
Prefetchable memory behind bridge: 88000000-8bffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
00: 02 10 71 43 07 00 a0 02 80 01 04 06 00 40 81 00
10: 00 00 00 00 00 00 00 00 00 08 09 40 21 21 80 22
20: 30 d0 30 d0 00 88 f0 8b 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 26 00 30 ff 00 00 00 00 3c 01 3a f1 00 00 00 00
50: 01 00 00 00 08 00 03 a8 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 06
e0: 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
40: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
60: 00 00 01 00 e4 00 00 00 20 c8 2f 0f 3c 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 08 00 01 21 20 a8 11 11 22 05 35 80 02 00 00 00
90: 5a 11 52 01 00 00 ff 00 07 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 03 00 00 00 00 00 7f 00 00 00 00 00 01 00 00 00
50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00
60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00
70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 03 00 d8 00 00 ff df 00 03 00 d4 00 80 ff d7 00
a0: 03 0a 00 00 00 0b 00 00 03 00 f0 00 00 ff ff 00
b0: 03 00 e0 00 80 ff ef 00 03 00 80 00 00 ff d3 00
c0: 00 00 00 00 00 00 00 00 13 10 00 00 00 f0 0f 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 03 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 00 00 00 01 01 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: e0 3e 78 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 46 00 00 00 00 00 00 00
80: 02 00 00 00 00 00 00 00 24 a2 68 5d 20 13 13 00
90: 20 0c 01 00 5a 80 10 67 39 00 00 80 00 00 00 00
a0: ed 06 00 5d 00 00 00 00 00 00 00 00 00 00 00 00
b0: 70 44 f9 95 09 00 00 00 27 c2 31 c4 f8 ad 80 0f
c0: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 30 87 14 c1 30 82 50 a8 00 08 4d 88 43 03 40 e0
e0: 20 02 15 8f 61 42 00 c4 60 0a 0e 88 34 05 48 c4
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]
00: 22 10 03 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00
40: ff 3b 04 00 40 00 10 0a 00 00 00 00 00 00 00 00
50: 10 02 00 00 80 00 00 00 00 00 00 00 00 80 10 52
60: 1d 00 00 00 01 77 1f 00 c0 00 00 00 00 00 00 00
70: 11 01 32 51 21 40 70 50 00 2a 00 08 17 21 00 00
80: 31 33 07 33 13 31 13 31 00 00 00 00 00 00 00 00
90: 00 00 00 00 4f 0a 00 00 10 00 12 21 00 00 00 00
a0: 9e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 01 a7 0d 00 00 00 10 09 25 25 25 00
e0: 00 00 00 00 20 0e 64 00 01 17 00 00 00 00 00 00
f0: 0f 00 10 00 00 00 00 00 00 00 00 00 82 0f 04 00
01:05.0 VGA compatible controller: ATI Technologies Inc RS485 [Radeon Xpress
1100 IGP] (prog-if 00 [VGA])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d4000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at d0120000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 75 59 07 00 b0 02 00 00 00 03 08 42 00 00
10: 08 00 00 d4 01 90 00 00 00 00 10 d0 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 08 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
50: 01 00 02 06 00 00 00 00 02 50 20 00 30 02 00 4f
60: 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
07:00.0 Network controller: Broadcom Corporation Unknown device 4328 (rev 01)
Subsystem: AMBIT Microsystem Corp. Unknown device 0319
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0200000 (64-bit, non-prefetchable) [disabled] [size=16K]
Region 2: Memory at d8000000 (64-bit, prefetchable) [disabled] [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM unknown, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [15c] Power Budgeting
00: e4 14 28 43 00 00 10 00 01 00 80 02 00 00 00 00
10: 04 00 20 d0 00 00 00 00 0c 00 00 d8 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 68 14 19 03
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
40: 01 58 02 06 00 40 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 05 d0 80 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 10 00 18 00 00 00 00 01 00 00 00 03 00 00 00
90: 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 10 00 01 00 a0 0f 00 00 00 00 11 00 11 60 03 00
e0: 00 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
08:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit
Ethernet (rev 03)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d0300000 (32-bit, non-prefetchable) [disabled] [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3
Enable-
Address: ffff6bfe7fffffb8 Data: fec7
00: e4 14 9c 16 00 00 b0 02 03 00 00 02 00 00 00 00
10: 00 00 30 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 07 00 00 00 25 10 0e 01
30: 00 00 ff ff 48 00 00 00 00 00 00 00 0a 01 40 00
40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 21 00 64
50: 03 58 fc 00 6f bf be 7f 05 00 86 00 b8 ff ff 7f
60: fe 6b ff ff c7 fe 00 00 9a 00 03 30 00 00 00 00
70: 76 10 00 00 40 00 00 00 50 00 00 00 00 00 00 00
80: 03 58 fc 00 00 00 00 00 00 00 00 00 fe 90 09 04
90: 01 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
08:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0314000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=08, secondary=09, subordinate=0c, sec-latency=176
Memory window 0: 88000000-8bfff000 (prefetchable)
Memory window 1: 90000000-93fff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite-
16-bit legacy interface ports at 0001
00: 4c 10 39 80 07 00 10 02 00 00 07 06 08 40 82 00
10: 00 40 31 d0 a0 00 00 02 08 09 0c b0 00 00 00 88
20: 00 f0 ff 8b 00 00 00 90 00 f0 ff 93 00 20 00 00
30: fc 20 00 00 00 24 00 00 fc 24 00 00 0b 01 c0 01
40: 25 10 0e 01 01 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 60 d0 44 08 19 00 d4 02 00 00 17 00 22 1b 72 01
90: c0 02 66 60 00 00 00 00 00 00 00 00 00 00 00 00
a0: 01 00 12 fe 00 00 c0 00 00 00 00 00 00 00 00 00
b0: 00 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 36 24 47 50 20 16 00 73 00 00 00 00 00 00 00 00
08:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE
1394 Host Controller (prog-if 10 [OHCI])
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at d0315000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0310000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00: 4c 10 3a 80 16 00 10 02 00 10 00 0c 08 40 80 00
10: 00 50 31 d0 00 00 31 d0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 02 03 04
40: 00 00 00 00 01 00 02 7e 00 80 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 00
f0: 00 08 00 00 82 10 00 00 25 10 0e 01 00 00 00 00
08:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card
Reader (SD/MMC/MS/MS PRO/xD)
Subsystem: Acer Incorporated [ALI] Unknown device 010e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0316000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 4c 10 3b 80 06 00 10 02 00 00 80 01 08 40 80 00
10: 00 60 31 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 0e 01
30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 07 04
40: 00 00 00 00 01 00 02 7e 00 00 00 00 00 00 00 00
50: 25 10 0e 01 05 01 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
On Wed, 2007-08-01 at 10:01 +0200, Joachim Deguara wrote:
> Here are the lspci outputs for the tg3
You have 2 Broadcom devices in your system. 07:00.0 is a wireless
device, I think. 8:4.0 is the tg3 device.
It's clear that the tg3 device is still in D3 state after resume and
that explains why all register accesses fail. tg3_resume() should put
the device back in D0 state in a very straight forward way and I don't
see how that can fail. It worked for me when I tested it last night.
Can you add some printk() to tg3_resume() to see what's happening? Let
me know if you want me to send you some debug patches to do that.
Thanks.
Here's the before and after for 8:4.0:
>
> Before
>
> 08:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit
> Ethernet (rev 03)
> Subsystem: Acer Incorporated [ALI] Unknown device 010e
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0 (16000ns min)
> Interrupt: pin A routed to IRQ 22
> Region 0: Memory at d0300000 (32-bit, non-prefetchable) [size=64K]
> Expansion ROM at <ignored> [disabled]
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [50] Vital Product Data
> Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3
> Enable-
> Address: ffff6bfe7fffffb8 Data: fec7
> 00: e4 14 9c 16 06 00 b0 02 03 00 00 02 00 00 00 00
> 10: 00 00 30 d0 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 07 00 00 00 25 10 0e 01
> 30: 00 00 ff ff 48 00 00 00 00 00 00 00 0a 01 40 00
> 40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 20 00 00
> 50: 03 58 fc 00 6f bf be 7f 05 00 86 00 b8 ff ff 7f
> 60: fe 6b ff ff c7 fe 00 00 98 00 03 30 00 00 3f 76
> 70: f6 10 00 00 20 00 00 80 14 04 00 00 00 00 00 00
> 80: 85 6b d0 36 03 40 00 0c 34 00 13 04 82 90 09 04
> 90: 09 97 00 01 00 00 00 00 00 00 00 00 eb 01 00 00
> a0: 00 00 00 00 23 01 00 00 00 00 00 00 cb 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> After
>
> 08:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit
> Ethernet (rev 03)
> Subsystem: Acer Incorporated [ALI] Unknown device 010e
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 22
> Region 0: Memory at d0300000 (32-bit, non-prefetchable) [disabled] [size=64K]
> Expansion ROM at <ignored> [disabled]
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
> Capabilities: [50] Vital Product Data
> Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3
> Enable-
> Address: ffff6bfe7fffffb8 Data: fec7
> 00: e4 14 9c 16 00 00 b0 02 03 00 00 02 00 00 00 00
> 10: 00 00 30 d0 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 07 00 00 00 25 10 0e 01
> 30: 00 00 ff ff 48 00 00 00 00 00 00 00 0a 01 40 00
> 40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 21 00 64
> 50: 03 58 fc 00 6f bf be 7f 05 00 86 00 b8 ff ff 7f
> 60: fe 6b ff ff c7 fe 00 00 9a 00 03 30 00 00 00 00
> 70: 76 10 00 00 40 00 00 00 50 00 00 00 00 00 00 00
> 80: 03 58 fc 00 00 00 00 00 00 00 00 00 fe 90 09 04
> 90: 01 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
On Wed, 2007-08-01 at 10:47 -0700, Michael Chan wrote:
> You have 2 Broadcom devices in your system. 07:00.0 is a wireless
> device, I think. 8:4.0 is the tg3 device.
>
> It's clear that the tg3 device is still in D3 state after resume and
> that explains why all register accesses fail. tg3_resume() should put
> the device back in D0 state in a very straight forward way and I don't
> see how that can fail. It worked for me when I tested it last night.
> Can you add some printk() to tg3_resume() to see what's happening? Let
> me know if you want me to send you some debug patches to do that.
I misread the PCI registers below. The power state was ok.
The problem is that memory enable and bus master were not set in PCI
register 4 after resume. This also explains the register access
failures.
In tg3_resume(), we call pci_restore_state() which should re-enable
those 2 bits in PCI register 4. Can you add some printk() to see why
those bits are not restored after pci_restore_state()?
Thanks.
>
> Here's the before and after for 8:4.0:
>
> >
> > Before
> >
> > 08:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit
> > Ethernet (rev 03)
> > Subsystem: Acer Incorporated [ALI] Unknown device 010e
> > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> > SERR- FastB2B-
> > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> > <MAbort- >SERR- <PERR-
> > Latency: 0 (16000ns min)
> > Interrupt: pin A routed to IRQ 22
> > Region 0: Memory at d0300000 (32-bit, non-prefetchable) [size=64K]
> > Expansion ROM at <ignored> [disabled]
> > Capabilities: [48] Power Management version 2
> > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
> > Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> > Capabilities: [50] Vital Product Data
> > Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3
> > Enable-
> > Address: ffff6bfe7fffffb8 Data: fec7
> > 00: e4 14 9c 16 06 00 b0 02 03 00 00 02 00 00 00 00
> > 10: 00 00 30 d0 00 00 00 00 00 00 00 00 00 00 00 00
> > 20: 00 00 00 00 00 00 00 00 07 00 00 00 25 10 0e 01
> > 30: 00 00 ff ff 48 00 00 00 00 00 00 00 0a 01 40 00
> > 40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 20 00 00
> > 50: 03 58 fc 00 6f bf be 7f 05 00 86 00 b8 ff ff 7f
> > 60: fe 6b ff ff c7 fe 00 00 98 00 03 30 00 00 3f 76
> > 70: f6 10 00 00 20 00 00 80 14 04 00 00 00 00 00 00
> > 80: 85 6b d0 36 03 40 00 0c 34 00 13 04 82 90 09 04
> > 90: 09 97 00 01 00 00 00 00 00 00 00 00 eb 01 00 00
> > a0: 00 00 00 00 23 01 00 00 00 00 00 00 cb 00 00 00
> > b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> >
> > After
> >
> > 08:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit
> > Ethernet (rev 03)
> > Subsystem: Acer Incorporated [ALI] Unknown device 010e
> > Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> > SERR- FastB2B-
> > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> > <MAbort- >SERR- <PERR-
> > Interrupt: pin A routed to IRQ 22
> > Region 0: Memory at d0300000 (32-bit, non-prefetchable) [disabled] [size=64K]
> > Expansion ROM at <ignored> [disabled]
> > Capabilities: [48] Power Management version 2
> > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
> > Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
> > Capabilities: [50] Vital Product Data
> > Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3
> > Enable-
> > Address: ffff6bfe7fffffb8 Data: fec7
> > 00: e4 14 9c 16 00 00 b0 02 03 00 00 02 00 00 00 00
> > 10: 00 00 30 d0 00 00 00 00 00 00 00 00 00 00 00 00
> > 20: 00 00 00 00 00 00 00 00 07 00 00 00 25 10 0e 01
> > 30: 00 00 ff ff 48 00 00 00 00 00 00 00 0a 01 40 00
> > 40: 00 00 00 00 00 00 00 00 01 50 02 c0 00 21 00 64
> > 50: 03 58 fc 00 6f bf be 7f 05 00 86 00 b8 ff ff 7f
> > 60: fe 6b ff ff c7 fe 00 00 9a 00 03 30 00 00 00 00
> > 70: 76 10 00 00 40 00 00 00 50 00 00 00 00 00 00 00
> > 80: 03 58 fc 00 00 00 00 00 00 00 00 00 fe 90 09 04
> > 90: 01 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> >
On Wednesday 01 August 2007 23:00:23 Michael Chan wrote:
> On Wed, 2007-08-01 at 10:47 -0700, Michael Chan wrote:
> > You have 2 Broadcom devices in your system. 07:00.0 is a wireless
> > device, I think. 8:4.0 is the tg3 device.
> >
> > It's clear that the tg3 device is still in D3 state after resume and
> > that explains why all register accesses fail. tg3_resume() should put
> > the device back in D0 state in a very straight forward way and I don't
> > see how that can fail. It worked for me when I tested it last night.
> > Can you add some printk() to tg3_resume() to see what's happening? Let
> > me know if you want me to send you some debug patches to do that.
>
> I misread the PCI registers below. The power state was ok.
>
> The problem is that memory enable and bus master were not set in PCI
> register 4 after resume. This also explains the register access
> failures.
>
> In tg3_resume(), we call pci_restore_state() which should re-enable
> those 2 bits in PCI register 4. Can you add some printk() to see why
> those bits are not restored after pci_restore_state()?
Reading pci_restore_state() it looks already instrumented. Sorry about the
wrong pci device, looking at my BCM5788 it is pci device 08:04.0 and looking
at the log from my first post there is nothing restored in the first 64
bytes! Otherwise it would have said "PM: Writing back..."
Is this what you are looking for or should I do other printk instrumentation?
-Joachim
On Thursday 02 August 2007 10:05:44 Joachim Deguara wrote:
> On Wednesday 01 August 2007 23:00:23 Michael Chan wrote:
> > On Wed, 2007-08-01 at 10:47 -0700, Michael Chan wrote:
> > The problem is that memory enable and bus master were not set in PCI
> > register 4 after resume. This also explains the register access
> > failures.
Found it! I did the instrumentation and found pci_restore was not being
called. Why, because this code failed:
printk(KERN_INFO "tg3_resume: entered\n");
if (!netif_running(dev))
return 0;
printk(KERN_INFO "tg3_resume: before restore\n");
Bad dmesg:
[ 0.581236] PM: Writing back config space on device 0000:07:00.0 at offset
4
(was 4, writing d0200004)
[ 0.581259] tg3_resume: entered
[ 0.581276] PM: Writing back config space on device 0000:08:09.0 at offset
f
(was c001ff, writing 1c0010b)
why is this, oh damn it is because I was calling openSUSE's "powersave -u" and
not s2ram directly. powersave is disabling the network and the tg3 will not
restore the pci device like this! right?
here is a good dmesg with by calling s2ram:
[ 0.577085] PM: Writing back config space on device 0000:07:00.0 at offset
4
(was 4, writing d0200004)
[ 0.577108] tg3_resume: entered
[ 0.577109] tg3_resume: before restore
[ 0.577140] PM: Writing back config space on device 0000:08:04.0 at offset
c
(was 0, writing ffff0000)
[ 0.577171] PM: Writing back config space on device 0000:08:04.0 at offset
1
(was 2b00000, writing 2b00006)
[ 0.577304] tg3_resume: after set_power_state
[ 0.579119] tg3: eth0: Link is down.
[ 0.786266] ata2: SATA link down (SStatus 0 SControl 310)
[ 0.848176] tg3_resume: after tg3_restart_hw
[ 0.848265] PM: Writing back config space on device 0000:08:09.0 at offset
f
(was c001ff, writing 1c0010b)
Seams like even if powersave shuts down the network that the device should
still work after a suspend to ram, so who is at fault here?
-Joachim
From: "Joachim Deguara" <[email protected]>
Date: Thu, 2 Aug 2007 11:15:05 +0200
> Seams like even if powersave shuts down the network that the device should
> still work after a suspend to ram, so who is at fault here?
It's a good question.
The pci_enable() is done on the PCI device at probe time, at least in
the tg3 driver, and with such a model restoring and saving of PCI
config space should not be dependant upon whether the netdev is
running or not.
On Thu, 2007-08-02 at 02:23 -0700, David Miller wrote:
> From: "Joachim Deguara" <[email protected]>
> Date: Thu, 2 Aug 2007 11:15:05 +0200
>
> > Seams like even if powersave shuts down the network that the device should
> > still work after a suspend to ram, so who is at fault here?
>
> It's a good question.
>
> The pci_enable() is done on the PCI device at probe time, at least in
> the tg3 driver, and with such a model restoring and saving of PCI
> config space should not be dependant upon whether the netdev is
> running or not.
>
Alternatively, we can also fix it by calling pci_enable_device() again
in tg3_open(). But I think it is better to just always save and restore
in suspend/resume. bnx2.c will also require the same fix.
Thanks Joachim for helping to debug this problem. Please try this
patch:
[TG3]: Fix suspend/resume problem.
Joachim Deguara <[email protected]> reported that tg3 devices
would not resume properly if the device was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
tg3_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
tg3_suspend() and tg3_resume() regardless of netif_running() state.
Signed-off-by: Michael Chan <[email protected]>
diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
index dc41c05..5874042 100644
--- a/drivers/net/tg3.c
+++ b/drivers/net/tg3.c
@@ -64,8 +64,8 @@
#define DRV_MODULE_NAME "tg3"
#define PFX DRV_MODULE_NAME ": "
-#define DRV_MODULE_VERSION "3.79"
-#define DRV_MODULE_RELDATE "July 18, 2007"
+#define DRV_MODULE_VERSION "3.80"
+#define DRV_MODULE_RELDATE "August 2, 2007"
#define TG3_DEF_MAC_MODE 0
#define TG3_DEF_RX_MODE 0
@@ -12111,6 +12111,12 @@ static int tg3_suspend(struct pci_dev *pdev, pm_message_t state)
struct tg3 *tp = netdev_priv(dev);
int err;
+ /* PCI register 4 needs to be saved whether netif_running() or not.
+ * MSI address and data need to be saved if using MSI and
+ * netif_running().
+ */
+ pci_save_state(pdev);
+
if (!netif_running(dev))
return 0;
@@ -12130,9 +12136,6 @@ static int tg3_suspend(struct pci_dev *pdev, pm_message_t state)
tp->tg3_flags &= ~TG3_FLAG_INIT_COMPLETE;
tg3_full_unlock(tp);
- /* Save MSI address and data for resume. */
- pci_save_state(pdev);
-
err = tg3_set_power_state(tp, pci_choose_state(pdev, state));
if (err) {
tg3_full_lock(tp, 0);
@@ -12160,11 +12163,11 @@ static int tg3_resume(struct pci_dev *pdev)
struct tg3 *tp = netdev_priv(dev);
int err;
+ pci_restore_state(tp->pdev);
+
if (!netif_running(dev))
return 0;
- pci_restore_state(tp->pdev);
-
err = tg3_set_power_state(tp, PCI_D0);
if (err)
return err;
From: "Michael Chan" <[email protected]>
Date: Thu, 02 Aug 2007 12:10:29 -0700
> On Thu, 2007-08-02 at 02:23 -0700, David Miller wrote:
> > From: "Joachim Deguara" <[email protected]>
> > Date: Thu, 2 Aug 2007 11:15:05 +0200
> >
> > > Seams like even if powersave shuts down the network that the device should
> > > still work after a suspend to ram, so who is at fault here?
> >
> > It's a good question.
> >
> > The pci_enable() is done on the PCI device at probe time, at least in
> > the tg3 driver, and with such a model restoring and saving of PCI
> > config space should not be dependant upon whether the netdev is
> > running or not.
> >
>
> Alternatively, we can also fix it by calling pci_enable_device() again
> in tg3_open(). But I think it is better to just always save and restore
> in suspend/resume. bnx2.c will also require the same fix.
We could do it that way. But don't you think it's more reliable to
save and restore around the event we know will be what clobbers the
PCI config space on us? :-)
Other things might happen between ->resume() and ->open() that could
modify PCI config space, and we could overwrite such changes if we do
the PCI restore in ->open().
One thing that's interesting to me is that, essentially, every PCI
driver with very few if any exceptions needs to do this sequence on
suspend and resume. It would be nice if there was a way to get this
to happen transparently by default, with some reasonable override
mechanism, for PCI device drivers.
Anyways, once your patch is tested feel free to send me the bnx2
one too.
Thanks!
On Thu, 2007-08-02 at 15:06 -0700, David Miller wrote:
> From: "Michael Chan" <[email protected]>
> Date: Thu, 02 Aug 2007 12:10:29 -0700
>
> > Alternatively, we can also fix it by calling pci_enable_device() again
> > in tg3_open(). But I think it is better to just always save and restore
> > in suspend/resume. bnx2.c will also require the same fix.
>
> We could do it that way. But don't you think it's more reliable to
> save and restore around the event we know will be what clobbers the
> PCI config space on us? :-)
>
Yes for sure when netif state is running and we were already doing that.
> Other things might happen between ->resume() and ->open() that could
> modify PCI config space, and we could overwrite such changes if we do
> the PCI restore in ->open().
I suggested calling pci_enable_device() in ->open(), not calling
pci_restore_state() in ->open(). I ultimately decided against it
because some devices do not enable memory as a workaround and it would
be messy to deal with it again in tg3_open().
I definitely agree that calling PCI restore in ->open() is a bad idea.
We used to save PCI state in ->probe() once and restore PCI state after
every chip reset. This sequence caused many subtle problems.
On Thursday 02 August 2007 21:10:29 Michael Chan wrote:
> Alternatively, we can also fix it by calling pci_enable_device() again
> in tg3_open(). But I think it is better to just always save and restore
> in suspend/resume. bnx2.c will also require the same fix.
>
> Thanks Joachim for helping to debug this problem. Please try this
> patch:
Patch works for me.
-Joachim
From: "Michael Chan" <[email protected]>
Date: Thu, 02 Aug 2007 12:10:29 -0700
> [TG3]: Fix suspend/resume problem.
>
> Joachim Deguara <[email protected]> reported that tg3 devices
> would not resume properly if the device was shutdown before the system
> was suspended. In such scenario where the netif_running state is 0,
> tg3_suspend() would not save the PCI state and so the memory enable bit
> and bus master enable bit would be lost.
>
> We fix this by always saving and restoring the PCI state in
> tg3_suspend() and tg3_resume() regardless of netif_running() state.
>
> Signed-off-by: Michael Chan <[email protected]>
Patch applied.