Hi there,
I experience a lot of hardware interrupts with a BCM5751 PCI-express NIC
(tg3). modprobe tg3, ifconfig ethX up and friends makes the system
unresponsive. Just having the interface up makes the system sluggish.
Onboard forcedeth works fine (with the same cable).
iperf gives me just 2Mbps on a 1Gbps ethernet. Load average near 1.0. top
reports 40-50%hi (hardware interrupts) when generating traffic over that
interface.
The system is a Supermicro H8SMI-2 motherboard, HP EA833AA BROADCOM
NETXTREME PCI-express NIC, 2GB RAM, Dual-Core opteron 2.8GHz.
All of our other servers with broadcom NIC's work fine with tg3, but they
aren't PCI-express.
I have tried booting with pci=nomsi and pci=routeirq (BIOS with or without
"pnp OS" defined). Ubuntu 7.10 live-cd same result. Haven't tried other
OS'es.
irq_balancing enabled.
Kernel conf: http://www.iki.fi/~harald/kernconf.gz (9kB).
Any hints on what to check for? Hardware or tg3 driverproblem?
I would be glad to report more info, if needed. I have profiling support
but I have never profiled a kernel before. I haven't got any other PCI-e
NIC's to test with, yet.
# uname -r
2.6.24.4
# dmesg|grep tg
tg3.c:v3.86 (November 9, 2007)
# lspci -vvv
07:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express (rev 21)
Subsystem: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 216
Region 0: Memory at febf0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at febe0000 [disabled] [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable+
Address: 00000000fee0300c Data: 4142
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
--
A: Top Posters! | s/y Charlotta |
Q: What is the most annoying thing on mailing lists? | FIN-2674 |
http://www.fe83.org/ Finn Express Purjehtijat ry | ============= |
Harald H Hannelius | harald (At) iki (dot) fi | GSM +358 50 594 1020
From: Harald Hannelius <[email protected]>
Date: Thu, 27 Mar 2008 15:53:56 +0200 (EET)
You'll have better luck if you report this to the networking
developer list (netdev) and the tg3 driver maintainer (Michael
Chan), who are both now CC:'d.
> I experience a lot of hardware interrupts with a BCM5751 PCI-express NIC
> (tg3). modprobe tg3, ifconfig ethX up and friends makes the system
> unresponsive. Just having the interface up makes the system sluggish.
>
> Onboard forcedeth works fine (with the same cable).
>
> iperf gives me just 2Mbps on a 1Gbps ethernet. Load average near 1.0. top
> reports 40-50%hi (hardware interrupts) when generating traffic over that
> interface.
>
> The system is a Supermicro H8SMI-2 motherboard, HP EA833AA BROADCOM
> NETXTREME PCI-express NIC, 2GB RAM, Dual-Core opteron 2.8GHz.
>
> All of our other servers with broadcom NIC's work fine with tg3, but they
> aren't PCI-express.
>
> I have tried booting with pci=nomsi and pci=routeirq (BIOS with or without
> "pnp OS" defined). Ubuntu 7.10 live-cd same result. Haven't tried other
> OS'es.
>
> irq_balancing enabled.
>
> Kernel conf: http://www.iki.fi/~harald/kernconf.gz (9kB).
>
> Any hints on what to check for? Hardware or tg3 driverproblem?
>
>
> I would be glad to report more info, if needed. I have profiling support
> but I have never profiled a kernel before. I haven't got any other PCI-e
> NIC's to test with, yet.
>
>
> # uname -r
> 2.6.24.4
>
> # dmesg|grep tg
> tg3.c:v3.86 (November 9, 2007)
>
> # lspci -vvv
> 07:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express (rev 21)
> Subsystem: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 216
> Region 0: Memory at febf0000 (64-bit, non-prefetchable) [size=64K]
> Expansion ROM at febe0000 [disabled] [size=64K]
> Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
> Capabilities: [50] Vital Product Data
> Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable+
> Address: 00000000fee0300c Data: 4142
> Capabilities: [d0] Express Endpoint IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
> Device: Latency L0s <4us, L1 unlimited
> Device: AtnBtn- AtnInd- PwrInd-
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
> Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
> Link: Latency L0s <4us, L1 <64us
> Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
> Link: Speed 2.5Gb/s, Width x1
>
>
> --
> A: Top Posters! | s/y Charlotta |
> Q: What is the most annoying thing on mailing lists? | FIN-2674 |
> http://www.fe83.org/ Finn Express Purjehtijat ry | ============= |
> Harald H Hannelius | harald (At) iki (dot) fi | GSM +358 50 594 1020
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
On Thu, 2008-03-27 at 14:49 -0700, David Miller wrote:
> From: Harald Hannelius <[email protected]>
> Date: Thu, 27 Mar 2008 15:53:56 +0200 (EET)
>
> > I experience a lot of hardware interrupts with a BCM5751 PCI-express NIC
> > (tg3). modprobe tg3, ifconfig ethX up and friends makes the system
> > unresponsive. Just having the interface up makes the system sluggish.
> >
I just tested a similar NIC using the same kernel and driver, but I did
not notice anything unusual. netperf gave me 941Mbps.
> > Onboard forcedeth works fine (with the same cable).
> >
> > iperf gives me just 2Mbps on a 1Gbps ethernet. Load average near 1.0. top
> > reports 40-50%hi (hardware interrupts) when generating traffic over that
> > interface.
Can you look at /proc/interrupts to see roughly how many are reported
per second when link is down, link is up with no traffic, and with
traffic?
Finally, you can also try ethtool -t eth0 to see if it passes a simple
self test.
On Thu, 27 Mar 2008, Michael Chan wrote:
> On Thu, 2008-03-27 at 14:49 -0700, David Miller wrote:
>> From: Harald Hannelius <[email protected]>
>> Date: Thu, 27 Mar 2008 15:53:56 +0200 (EET)
>>
>>> I experience a lot of hardware interrupts with a BCM5751 PCI-express NIC
>>> (tg3). modprobe tg3, ifconfig ethX up and friends makes the system
>>> unresponsive. Just having the interface up makes the system sluggish.
>>>
>
> I just tested a similar NIC using the same kernel and driver, but I did
> not notice anything unusual. netperf gave me 941Mbps.
>
>>> Onboard forcedeth works fine (with the same cable).
>>>
>>> iperf gives me just 2Mbps on a 1Gbps ethernet. Load average near 1.0. top
>>> reports 40-50%hi (hardware interrupts) when generating traffic over that
>>> interface.
>
> Can you look at /proc/interrupts to see roughly how many are reported
> per second when link is down, link is up with no traffic, and with
> traffic?
>
> Finally, you can also try ethtool -t eth0 to see if it passes a simple
> self test.
Phew, I thought that running ethtool -t was like doing stop-A-sync on a
Sun. It took almost half an hour to run that ethtool -t command;
'mpstat 2' output while running 'ethtool -t eth2':
Full log here (2160 lines): http://www.iki.fi/~harald/mpstat.log
A few lines from that log here;
Linux 2.6.24.4 (mauer) 03/28/2008
10:37:14 AM CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s
10:37:16 AM all 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 115.50
10:37:18 AM all 0.00 0.00 1.00 0.00 0.00 0.00 0.00 99.00 123.50
10:37:20 AM all 0.00 0.00 0.75 0.00 0.00 0.00 0.00 99.25 142.79
10:37:23 AM all 0.00 0.00 25.66 0.00 23.77 2.26 0.00 48.30 76.38
10:37:25 AM all 0.00 0.00 17.13 0.00 31.12 21.68 0.00 30.07 75.12
10:37:27 AM all 0.00 0.00 12.17 0.00 25.48 28.90 0.00 33.46 103.00
10:37:29 AM all 0.00 0.00 0.40 0.00 38.15 23.29 0.00 38.15 70.15
10:37:31 AM all 0.00 0.00 0.40 0.00 41.90 23.32 0.00 34.39 71.43
10:37:33 AM all 0.00 0.00 2.83 0.00 29.68 34.98 0.00 32.51 123.38
10:37:35 AM all 0.00 0.00 11.07 0.00 33.21 24.81 0.00 30.92 78.74
... goes on like this for almost half-an-hour ...
11:04:03 AM all 0.00 0.00 0.00 0.00 34.69 22.86 0.00 42.45 71.50
11:04:05 AM all 0.00 0.00 1.53 0.00 33.72 26.82 0.00 37.93 84.50
11:04:07 AM all 0.00 0.00 0.40 0.00 38.15 22.89 0.00 38.55 74.26
11:04:09 AM all 0.00 0.00 0.00 0.00 38.80 21.60 0.00 39.60 72.64
11:04:11 AM all 0.00 0.00 0.00 0.00 42.17 23.29 0.00 34.54 69.50
11:04:13 AM all 0.00 0.00 3.60 1.44 31.29 33.45 0.00 30.22 111.39
11:04:15 AM all 0.00 0.00 0.00 0.00 0.51 0.76 0.00 98.73 110.50
11:04:17 AM all 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 119.50
11:04:19 AM all 0.00 0.00 0.25 1.24 0.00 0.00 0.00 98.51 126.87
11:04:21 AM all 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 106.50
... command finished ...
Sadly I didn't capture the output from ethtool -t, failed anyway. I'm
running that test a second time right now, I'll post the output later
(when finished). While the 'ethtool -t eth2' is running eth0 (forcedeth)
doesn't respond to ping, when going to the console it didn't wake up with
a keypress, nor did capslock/numlock react.
'mpstat 2' while running modprobe tg3:
Linux 2.6.24.4 (mauer) 03/28/2008
02:47:05 PM CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s
02:47:07 PM all 0.00 0.00 0.75 0.00 0.00 0.00 0.00 99.25 138.00
02:47:09 PM all 0.00 0.00 0.25 0.00 0.00 0.00 0.00 99.75 120.00
02:47:11 PM all 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00 132.50
02:47:13 PM all 0.00 0.00 14.19 0.00 17.16 1.65 0.00 67.00 92.08
02:47:15 PM all 0.00 0.00 19.60 0.00 30.40 1.20 0.00 48.80 60.50
02:47:17 PM all 0.56 0.00 4.20 0.00 5.88 0.28 0.00 89.08 127.14
02:47:19 PM all 0.00 0.00 0.75 0.00 0.25 0.00 0.00 99.00 127.00
'mpstat 2' while running ifconfig eth2 up:
Linux 2.6.24.4 (mauer) 03/28/2008
02:47:50 PM CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s
02:47:52 PM all 0.00 0.00 0.40 0.00 44.95 16.49 0.00 38.16 194.47
02:47:54 PM all 0.00 0.00 0.76 0.00 46.91 16.77 0.00 35.56 205.47
02:47:56 PM all 0.00 0.00 2.06 0.00 15.88 14.12 0.00 67.94 107.96
Hope my overlong lines don't get wrapped...
No hints on dmesg on what's going on.
--
A: Top Posters! | s/y Charlotta |
Q: What is the most annoying thing on mailing lists? | FIN-2674 |
http://www.fe83.org/ Finn Express Purjehtijat ry | ============= |
Harald H Hannelius | harald (At) iki (dot) fi | GSM +358 50 594 1020
On Fri, 2008-03-28 at 15:04 +0200, Harald Hannelius wrote:
> Phew, I thought that running ethtool -t was like doing stop-A-sync on
> a
> Sun. It took almost half an hour to run that ethtool -t command;
Something is very wrong. ethtool -t should only take a few seconds to
complete. You can try ethtool -t eth0 online to reduce the number of
tests to see if it makes a difference.
How many of these NICs do you have? If you have more than one, do they
all behave the same way? Have they ever worked well before?
On Fri, 28 Mar 2008, Michael Chan wrote:
> > Phew, I thought that running ethtool -t was like doing stop-A-sync on
> > a Sun. It took almost half an hour to run that ethtool -t command;
> Something is very wrong. ethtool -t should only take a few seconds to
> complete. You can try ethtool -t eth0 online to reduce the number of
> tests to see if it makes a difference.
> How many of these NICs do you have? If you have more than one, do they
> all behave the same way? Have they ever worked well before?
Harald, is the IRQ of eth0 shared with any other device? (cat
/proc/interrupts will show).
--
Jiri Kosina
SUSE Labs
On Fri, 28 Mar 2008, Michael Chan wrote:
> On Fri, 2008-03-28 at 15:04 +0200, Harald Hannelius wrote:
>> Phew, I thought that running ethtool -t was like doing stop-A-sync on
>> a
>> Sun. It took almost half an hour to run that ethtool -t command;
>
> Something is very wrong. ethtool -t should only take a few seconds to
> complete. You can try ethtool -t eth0 online to reduce the number of
> tests to see if it makes a difference.
Here's the output of ethtool -t eth2:
The test result is PASS
The test extra info:
nvram test (online) 0
link test (online) 0
register test (offline) 0
memory test (offline) 0
loopback test (offline) 0
interrupt test (offline) 0
I just started a 'ethtool -t eth2 online' and that one took just some 10
seconds or so.
# ethtool -t eth2 online 2>&1 | tee ethtool-output.log
The test result is PASS
The test extra info:
nvram test (online) 0
link test (online) 0
register test (offline) 0
memory test (offline) 0
loopback test (offline) 0
interrupt test (offline) 0
# mpstat 2 2>&1 | tee ethtool2.log
Linux 2.6.24.4 (mauer) 03/28/2008
05:22:42 PM CPU %user %nice %sys %iowait %irq %soft %steal %idle intr/s
05:22:44 PM all 0.00 0.00 0.00 0.00 11.63 7.56 0.00 80.81 102.99
05:22:46 PM all 0.00 0.00 0.27 0.00 8.33 4.84 0.00 86.56 123.00
05:22:48 PM all 0.00 0.00 0.00 0.00 12.03 7.16 0.00 80.80 108.46
05:22:50 PM all 0.00 0.00 0.00 0.00 10.47 5.23 0.00 84.30 113.93
05:22:52 PM all 0.00 0.00 0.00 0.00 12.93 10.06 0.00 77.01 135.00
05:22:55 PM all 0.00 0.00 18.11 0.00 24.25 12.62 0.00 45.02 158.28
05:22:57 PM all 0.00 0.00 0.82 0.00 13.11 10.38 0.00 75.68 146.04
05:22:59 PM all 0.00 0.00 0.29 0.00 18.77 12.61 0.00 68.33 136.32
05:23:01 PM all 0.00 0.00 0.00 0.00 13.64 7.67 0.00 78.69 112.50
05:23:03 PM all 0.00 0.00 0.00 0.00 9.19 4.86 0.00 85.95 110.50
05:23:05 PM all 0.00 0.00 0.00 0.00 13.64 7.67 0.00 78.69 108.00
> How many of these NICs do you have? If you have more than one, do they
> all behave the same way? Have they ever worked well before?
It's a brand spanking new computer, equipped with three of these BCM5751
NICs made by HP. I have ripped out all but one, and I have also tested the
NIC in all three available PCIe slots. Same result.
When all three NIC's where plugged in they didn't work. All three behave
the same one-by-one.
I don't know if they have worked before.
--
A: Top Posters! | s/y Charlotta |
Q: What is the most annoying thing on mailing lists? | FIN-2674 |
http://www.fe83.org/ Finn Express Purjehtijat ry | ============= |
Harald H Hannelius | harald (At) iki (dot) fi | GSM +358 50 594 1020
On Fri, 28 Mar 2008, Jiri Kosina wrote:
> On Fri, 28 Mar 2008, Michael Chan wrote:
>>> Phew, I thought that running ethtool -t was like doing stop-A-sync on
>>> a Sun. It took almost half an hour to run that ethtool -t command;
>> Something is very wrong. ethtool -t should only take a few seconds to
>> complete. You can try ethtool -t eth0 online to reduce the number of
>> tests to see if it makes a difference.
>> How many of these NICs do you have? If you have more than one, do they
>> all behave the same way? Have they ever worked well before?
>
> Harald, is the IRQ of eth0 shared with any other device? (cat
> /proc/interrupts will show).
# cat /proc/interrupts
CPU0 CPU1
0: 111 1 IO-APIC-edge timer
1: 0 2 IO-APIC-edge i8042
2: 0 0 XT-PIC-XT cascade
5: 0 0 IO-APIC-fasteoi sata_nv
7: 856 51 IO-APIC-fasteoi ohci_hcd:usb2
10: 0 3 IO-APIC-fasteoi sata_nv, ehci_hcd:usb1
11: 4305 7 IO-APIC-fasteoi sata_nv
12: 0 4 IO-APIC-edge i8042
216: 4217 128932 PCI-MSI-edge eth2
217: 161107 685351 PCI-MSI-edge eth0
NMI: 0 0 Non-maskable interrupts
LOC: 2380762 2619917 Local timer interrupts
RES: 3000 3269 Rescheduling interrupts
CAL: 16 31 function call interrupts
TLB: 64 111 TLB shootdowns
TRM: 0 0 Thermal event interrupts
SPU: 0 0 Spurious interrupts
ERR: 1
MIS: 0
Well, shared or not, yes and no. I think that /proc/interrupts contains
soft-interrupts. The problem child is interface eth2.
As rapported by ifconfig the interface is on IRQ 5:
# ifconfig eth2
eth2 Link encap:Ethernet HWaddr 00:10:18:30:E6:D6
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:196898 errors:0 dropped:0 overruns:0 frame:0
TX packets:19 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:69887991 (66.6 MiB) TX bytes:1216 (1.1 KiB)
Interrupt:5
That'd be the same as sata_nv.
# ifconfig eth2
eth2 Link encap:Ethernet HWaddr 00:10:18:30:E6:D6
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:196898 errors:0 dropped:0 overruns:0 frame:0
TX packets:19 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:69887991 (66.6 MiB) TX bytes:1216 (1.1 KiB)
Interrupt:5
I changed the settings "PnP OS" in the BIOS (acpi on/off?) and tried
booting with both pci=routeirq (or smth like that, see original post) on
and off to no avail.
I'm stumped. I have never experienced anything quite like this before.
Usually an IRQ-conflict has crashed my computers, not just slowed them
down (or maybe these dual-core opterons are just that incredibly fast
nowadays that the do nothing incredibly fast :) ). Then again, I haven't
had an IRQ-conflict on my boxen in years.
Buggy motherboard? Buggy NIC? The motherboard has the latest available
BIOS as per supermicro's webpage.
I'm getting three PCIe e1000's next week, I'll try with these instead.
--
A: Top Posters! | s/y Charlotta |
Q: What is the most annoying thing on mailing lists? | FIN-2674 |
http://www.fe83.org/ Finn Express Purjehtijat ry | ============= |
Harald H Hannelius | harald (At) iki (dot) fi | GSM +358 50 594 1020
On Fri, 2008-03-28 at 19:37 +0200, Harald Hannelius wrote:
> # cat /proc/interrupts
> CPU0 CPU1
> 0: 111 1 IO-APIC-edge timer
> 1: 0 2 IO-APIC-edge i8042
> 2: 0 0 XT-PIC-XT cascade
> 5: 0 0 IO-APIC-fasteoi sata_nv
> 7: 856 51 IO-APIC-fasteoi ohci_hcd:usb2
> 10: 0 3 IO-APIC-fasteoi sata_nv, ehci_hcd:usb1
> 11: 4305 7 IO-APIC-fasteoi sata_nv
> 12: 0 4 IO-APIC-edge i8042
> 216: 4217 128932 PCI-MSI-edge eth2
> 217: 161107 685351 PCI-MSI-edge eth0
> NMI: 0 0 Non-maskable interrupts
> LOC: 2380762 2619917 Local timer interrupts
> RES: 3000 3269 Rescheduling interrupts
> CAL: 16 31 function call interrupts
> TLB: 64 111 TLB shootdowns
> TRM: 0 0 Thermal event interrupts
> SPU: 0 0 Spurious interrupts
> ERR: 1
> MIS: 0
>
> Well, shared or not, yes and no. I think that /proc/interrupts
> contains
> soft-interrupts. The problem child is interface eth2.
>
> As rapported by ifconfig the interface is on IRQ 5:
eth2 is using MSI. When using MSI, the IRQ reported by ifconfig is not
accurate. You said you have tried booting with nomsi, but have you
confirmed that by checking /proc/interrupts?
>
> # ifconfig eth2
> eth2 Link encap:Ethernet HWaddr 00:10:18:30:E6:D6
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:196898 errors:0 dropped:0 overruns:0 frame:0
> TX packets:19 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:69887991 (66.6 MiB) TX bytes:1216 (1.1 KiB)
> Interrupt:5
>
On Fri, 28 Mar 2008, Michael Chan wrote:
> On Fri, 2008-03-28 at 19:37 +0200, Harald Hannelius wrote:
>> # cat /proc/interrupts
>> CPU0 CPU1
>> 0: 111 1 IO-APIC-edge timer
>> 1: 0 2 IO-APIC-edge i8042
>> 2: 0 0 XT-PIC-XT cascade
>> 5: 0 0 IO-APIC-fasteoi sata_nv
>> 7: 856 51 IO-APIC-fasteoi ohci_hcd:usb2
>> 10: 0 3 IO-APIC-fasteoi sata_nv, ehci_hcd:usb1
>> 11: 4305 7 IO-APIC-fasteoi sata_nv
>> 12: 0 4 IO-APIC-edge i8042
>> 216: 4217 128932 PCI-MSI-edge eth2
>> 217: 161107 685351 PCI-MSI-edge eth0
>> NMI: 0 0 Non-maskable interrupts
>> LOC: 2380762 2619917 Local timer interrupts
>> RES: 3000 3269 Rescheduling interrupts
>> CAL: 16 31 function call interrupts
>> TLB: 64 111 TLB shootdowns
>> TRM: 0 0 Thermal event interrupts
>> SPU: 0 0 Spurious interrupts
>> ERR: 1
>> MIS: 0
>>
>> Well, shared or not, yes and no. I think that /proc/interrupts
>> contains
>> soft-interrupts. The problem child is interface eth2.
>>
>> As rapported by ifconfig the interface is on IRQ 5:
>
> eth2 is using MSI. When using MSI, the IRQ reported by ifconfig is not
> accurate. You said you have tried booting with nomsi, but have you
> confirmed that by checking /proc/interrupts?
I did, at least the interface wasn't on MSI-edge anymore. I cannot
remember what IRQ the NIC took when booted with pci=nomsi (something like
that), it could have been 10 or other IRQ below 20, if I recall correctly.
--
A: Top Posters! | s/y Charlotta |
Q: What is the most annoying thing on mailing lists? | FIN-2674 |
http://www.fe83.org/ Finn Express Purjehtijat ry | ============= |
Harald H Hannelius | harald (At) iki (dot) fi | GSM +358 50 594 1020