From: Dinh Nguyen <[email protected]>
This patch is part of enabling USB for Freescale MX51 Babbage HW. This
patch updates the iomux pins for USB, and gpio line for reset the
USB hub on the MX51 Babbage HW.
NOTE: This 5-patch series for enabling USB is functionally dependent
on this patch:
"mx5: Add registration of GPIOs for MX51 Babbage board"
This patch applies to 2.6.34-rc5.
Signed-off-by: Dinh Nguyen <[email protected]>
---
arch/arm/plat-mxc/include/mach/iomux-mx51.h | 33 ++++++++++++++++----------
1 files changed, 20 insertions(+), 13 deletions(-)
diff --git a/arch/arm/plat-mxc/include/mach/iomux-mx51.h b/arch/arm/plat-mxc/include/mach/iomux-mx51.h
index b4f975e..80528cc 100644
--- a/arch/arm/plat-mxc/include/mach/iomux-mx51.h
+++ b/arch/arm/plat-mxc/include/mach/iomux-mx51.h
@@ -1,5 +1,6 @@
/*
* Copyright (C) 2009-2010 Amit Kucheria <[email protected]>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
@@ -37,6 +38,11 @@ typedef enum iomux_config {
PAD_CTL_SRE_FAST)
#define MX51_UART3_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_DSE_HIGH | \
PAD_CTL_SRE_FAST)
+#define MX51_USBH1_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
+ PAD_CTL_PKE | PAD_CTL_HYS)
+#define MX51_GPIO_PAD_CTRL (PAD_CTL_DSE_HIGH | PAD_CTL_PKE | \
+ PAD_CTL_SRE_FAST)
/*
* The naming convention for the pad modes is MX51_PAD_<padname>__<padmode>
@@ -208,18 +214,19 @@ typedef enum iomux_config {
#define MX51_PAD_KEY_COL3__KEY_COL3 IOMUX_PAD(0x658, 0x268, 0, 0x0, 0, NO_PAD_CTRL)
#define MX51_PAD_KEY_COL4__KEY_COL4 IOMUX_PAD(0x65C, 0x26C, 0, 0x0, 0, NO_PAD_CTRL)
#define MX51_PAD_KEY_COL5__KEY_COL5 IOMUX_PAD(0x660, 0x270, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_25__USBH1_CLK IOMUX_PAD(0x678, 0x278, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_26__USBH1_DIR IOMUX_PAD(0x67C, 0x27C, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_27__USBH1_STP IOMUX_PAD(0x680, 0x280, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_28__USBH1_NXT IOMUX_PAD(0x684, 0x284, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_11__USBH1_DATA0 IOMUX_PAD(0x688, 0x288, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_12__USBH1_DATA1 IOMUX_PAD(0x68C, 0x28C, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_13__USBH1_DATA2 IOMUX_PAD(0x690, 0x290, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_14__USBH1_DATA3 IOMUX_PAD(0x694, 0x294, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_15__USBH1_DATA4 IOMUX_PAD(0x698, 0x298, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_16__USBH1_DATA5 IOMUX_PAD(0x69C, 0x29C, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_17__USBH1_DATA6 IOMUX_PAD(0x6A0, 0x2A0, 2, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_18__USBH1_DATA7 IOMUX_PAD(0x6A4, 0x2A4, 2, 0x0, 0, NO_PAD_CTRL)
+#define MX51_PAD_USBH1_CLK__USBH1_CLK IOMUX_PAD(0x678, 0x278, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_DIR__USBH1_DIR IOMUX_PAD(0x67C, 0x27C, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_STP__USBH1_STP IOMUX_PAD(0x680, 0x280, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_STP__GPIO_1_27 IOMUX_PAD(0x680, 0x280, IOMUX_CONFIG_GPIO, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_NXT__USBH1_NXT IOMUX_PAD(0x684, 0x284, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_DATA0__USBH1_DATA0 IOMUX_PAD(0x688, 0x288, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_DATA1__USBH1_DATA1 IOMUX_PAD(0x68C, 0x28C, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_DATA2__USBH1_DATA2 IOMUX_PAD(0x690, 0x290, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_DATA3__USBH1_DATA3 IOMUX_PAD(0x694, 0x294, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_DATA4__USBH1_DATA4 IOMUX_PAD(0x698, 0x298, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_DATA5__USBH1_DATA5 IOMUX_PAD(0x69C, 0x29C, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_DATA6__USBH1_DATA6 IOMUX_PAD(0x6A0, 0x2A0, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
+#define MX51_PAD_USBH1_DATA7__USBH1_DATA7 IOMUX_PAD(0x6A4, 0x2A4, IOMUX_CONFIG_ALT0, 0x0, 0, MX51_USBH1_PAD_CTRL)
#define MX51_PAD_GPIO_3_0__DI1_PIN11 IOMUX_PAD(0x6A8, 0x2A8, 4, 0x0, 0, NO_PAD_CTRL)
#define MX51_PAD_GPIO_3_1__DI1_PIN12 IOMUX_PAD(0x6AC, 0x2AC, 4, 0x0, 0, NO_PAD_CTRL)
#define MX51_PAD_GPIO_3_2__DI1_PIN13 IOMUX_PAD(0x6B0, 0x2B0, 4, 0x0, 0, NO_PAD_CTRL)
@@ -299,7 +306,7 @@ typedef enum iomux_config {
#define MX51_PAD_GPIO_1_4__GPIO1_4 IOMUX_PAD(0x804, 0x3D8, 0, 0x0, 0, NO_PAD_CTRL)
#define MX51_PAD_GPIO_1_5__GPIO1_5 IOMUX_PAD(0x808, 0x3DC, 0, 0x0, 0, NO_PAD_CTRL)
#define MX51_PAD_GPIO_1_6__GPIO1_6 IOMUX_PAD(0x80C, 0x3E0, 0, 0x0, 0, NO_PAD_CTRL)
-#define MX51_PAD_GPIO_1_7__GPIO1_7 IOMUX_PAD(0x810, 0x3E4, 0, 0x0, 0, NO_PAD_CTRL)
+#define MX51_PAD_GPIO_1_7__GPIO1_7 IOMUX_PAD(0x810, 0x3E4, 0, 0x0, 0, MX51_GPIO_PAD_CTRL)
#define MX51_PAD_GPIO_1_8__GPIO1_8 IOMUX_PAD(0x814, 0x3E8, 0, 0x0, 1, \
(PAD_CTL_SRE_SLOW | PAD_CTL_DSE_MED | PAD_CTL_PUS_100K_UP | PAD_CTL_HYS))
#define MX51_PAD_GPIO_1_9__GPIO1_9 IOMUX_PAD(0x818, 0x3EC, 0, 0x0, 0, NO_PAD_CTRL)
--
1.6.0.4
From: Dinh Nguyen <[email protected]>
This patch enables USB host functionality for Host1 and OTG port on
Freescale MX51 Babbage HW. This patch contains the board specific
HW initialization of the USB HW.
This patch applies to 2.6.34-rc5.
Signed-off-by: Dinh Nguyen <[email protected]>
Reviewed-by: Daniel Mack <[email protected]>
---
arch/arm/mach-mx5/board-mx51_babbage.c | 129 ++++++++++++++++++++++++++++++++
1 files changed, 129 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-mx5/board-mx51_babbage.c b/arch/arm/mach-mx5/board-mx51_babbage.c
index ee67a71..99f7ea9 100644
--- a/arch/arm/mach-mx5/board-mx51_babbage.c
+++ b/arch/arm/mach-mx5/board-mx51_babbage.c
@@ -12,11 +12,15 @@
#include <linux/init.h>
#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/io.h>
#include <mach/common.h>
#include <mach/hardware.h>
#include <mach/imx-uart.h>
#include <mach/iomux-mx51.h>
+#include <mach/mxc_ehci.h>
#include <asm/irq.h>
#include <asm/setup.h>
@@ -26,6 +30,17 @@
#include "devices.h"
+#define BABBAGE_USB_HUB_RESET (0*32 + 7) /* GPIO_1_7 */
+#define BABBAGE_USBH1_STP (0*32 + 27) /* GPIO_1_27 */
+
+/* USB_CTRL_1 */
+#define MX51_USB_CTRL_1_OFFSET 0x10
+#define MX51_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
+
+#define MX51_USB_PLLDIV_12_MHZ 0x00
+#define MX51_USB_PLL_DIV_19_2_MHZ 0x01
+#define MX51_USB_PLL_DIV_24_MHZ 0x02
+
static struct platform_device *devices[] __initdata = {
&mxc_fec_device,
};
@@ -46,6 +61,22 @@ static struct pad_desc mx51babbage_pads[] = {
MX51_PAD_EIM_D26__UART3_TXD,
MX51_PAD_EIM_D27__UART3_RTS,
MX51_PAD_EIM_D24__UART3_CTS,
+
+ /* USB HOST1 */
+ MX51_PAD_USBH1_CLK__USBH1_CLK,
+ MX51_PAD_USBH1_DIR__USBH1_DIR,
+ MX51_PAD_USBH1_NXT__USBH1_NXT,
+ MX51_PAD_USBH1_DATA0__USBH1_DATA0,
+ MX51_PAD_USBH1_DATA1__USBH1_DATA1,
+ MX51_PAD_USBH1_DATA2__USBH1_DATA2,
+ MX51_PAD_USBH1_DATA3__USBH1_DATA3,
+ MX51_PAD_USBH1_DATA4__USBH1_DATA4,
+ MX51_PAD_USBH1_DATA5__USBH1_DATA5,
+ MX51_PAD_USBH1_DATA6__USBH1_DATA6,
+ MX51_PAD_USBH1_DATA7__USBH1_DATA7,
+
+ /* USB HUB reset line*/
+ MX51_PAD_GPIO_1_7__GPIO1_7,
};
/* Serial ports */
@@ -66,15 +97,113 @@ static inline void mxc_init_imx_uart(void)
}
#endif /* SERIAL_IMX */
+static int gpio_usbh1_active(void)
+{
+ struct pad_desc usbh1stp_gpio = MX51_PAD_USBH1_STP__GPIO_1_27;
+ int ret;
+
+ /* Set USBH1_STP to GPIO and toggle it */
+ mxc_iomux_v3_setup_pad(&usbh1stp_gpio);
+ ret = gpio_request(BABBAGE_USBH1_STP, "usbh1_stp");
+
+ if (ret) {
+ pr_debug("failed to get MX51_PAD_USBH1_STP__GPIO_1_27: %d\n", ret);
+ return ret;
+ }
+ gpio_direction_output(BABBAGE_USBH1_STP, 0);
+ gpio_set_value(BABBAGE_USBH1_STP, 1);
+ msleep(100);
+ gpio_free(BABBAGE_USBH1_STP);
+ return 0;
+}
+
+static inline void babbage_usbhub_reset(void)
+{
+ int ret;
+
+ /* Bring USB hub out of reset */
+ ret = gpio_request(BABBAGE_USB_HUB_RESET, "GPIO1_7");
+ if (ret) {
+ printk(KERN_ERR"failed to get GPIO_USB_HUB_RESET: %d\n", ret);
+ return;
+ }
+ gpio_direction_output(BABBAGE_USB_HUB_RESET, 0);
+
+ /* USB HUB RESET - De-assert USB HUB RESET_N */
+ msleep(1);
+ gpio_set_value(BABBAGE_USB_HUB_RESET, 0);
+ msleep(1);
+ gpio_set_value(BABBAGE_USB_HUB_RESET, 1);
+}
+
+/* This function is board specific as the bit mask for the plldiv will also
+be different for other Freescale SoCs, thus a common bitmask is not
+possible and cannot get place in /plat-mxc/ehci.c.*/
+static int initialize_otg_port(struct platform_device *pdev)
+{
+ u32 v;
+ void __iomem *usb_base;
+ u32 usbother_base;
+
+ usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
+ usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
+
+ /* Set the PHY clock to 19.2MHz */
+ v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
+ v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
+ v |= MX51_USB_PLL_DIV_19_2_MHZ;
+ __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
+ iounmap(usb_base);
+ return 0;
+}
+
+static int initialize_usbh1_port(struct platform_device *pdev)
+{
+ u32 v;
+ void __iomem *usb_base;
+ u32 usbother_base;
+
+ usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
+ usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
+
+ /* The clock for the USBH1 ULPI port will come externally from the PHY. */
+ v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
+ __raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN, usbother_base + MX51_USB_CTRL_1_OFFSET);
+ iounmap(usb_base);
+ return 0;
+}
+
+static struct mxc_usbh_platform_data dr_utmi_config = {
+ .init = initialize_otg_port,
+ .portsc = MXC_EHCI_UTMI_16BIT,
+ .flags = MXC_EHCI_INTERNAL_PHY,
+};
+
+static struct mxc_usbh_platform_data usbh1_config = {
+ .init = initialize_usbh1_port,
+ .portsc = MXC_EHCI_MODE_ULPI,
+ .flags = (MXC_EHCI_POWER_PINS_ENABLED | MXC_EHCI_ITC_NO_THRESHOLD),
+};
+
/*
* Board specific initialization.
*/
static void __init mxc_board_init(void)
{
+ struct pad_desc usbh1stp = MX51_PAD_USBH1_STP__USBH1_STP;
+
mxc_iomux_v3_setup_multiple_pads(mx51babbage_pads,
ARRAY_SIZE(mx51babbage_pads));
mxc_init_imx_uart();
platform_add_devices(devices, ARRAY_SIZE(devices));
+
+ mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
+
+ gpio_usbh1_active();
+ mxc_register_device(&mxc_usbh1_device, &usbh1_config);
+ /* setback USBH1_STP to be function */
+ mxc_iomux_v3_setup_pad(&usbh1stp);
+ babbage_usbhub_reset();
}
static void __init mx51_babbage_timer_init(void)
--
1.6.0.4
From: Dinh Nguyen <[email protected]>
Update mx51_defconfig to include USB EHCI by default.
This patch applies to 2.6.34-rc4.
Signed-off-by: Dinh Nguyen <[email protected]>
---
arch/arm/configs/mx51_defconfig | 17 ++++++++++++++++-
1 files changed, 16 insertions(+), 1 deletions(-)
diff --git a/arch/arm/configs/mx51_defconfig b/arch/arm/configs/mx51_defconfig
index c88e952..a708fd6 100644
--- a/arch/arm/configs/mx51_defconfig
+++ b/arch/arm/configs/mx51_defconfig
@@ -809,7 +809,22 @@ CONFIG_SSB_POSSIBLE=y
CONFIG_DUMMY_CONSOLE=y
# CONFIG_SOUND is not set
# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+CONFIG_USB_ARCH_HAS_EHCI=y
+CONFIG_USB=y
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_EHCI_MXC=y
+
+
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
# CONFIG_MMC_UNSAFE_RESUME is not set
--
1.6.0.4
From: Dinh Nguyen <[email protected]>
This patch adds USB HW initializiation code to /plat-mxc/ehci.c.
-Sets some specific PHY settings
Renames mxc_set_usbcontrol to mxc_initialize_usb_hw.
Adds new register bit defines for the USB HW on Freescale
SoCs.
This patch applies to 2.6.34-rc5.
Signed-off-by: Dinh Nguyen <[email protected]>
Reviewed-by: Daniel Mack <[email protected]>
---
arch/arm/mach-mx5/clock-mx51.c | 1 +
arch/arm/plat-mxc/ehci.c | 100 ++++++++++++++++++++++++++++-
arch/arm/plat-mxc/include/mach/mxc_ehci.h | 14 ++++-
drivers/usb/host/ehci-mxc.c | 4 +-
4 files changed, 114 insertions(+), 5 deletions(-)
diff --git a/arch/arm/mach-mx5/clock-mx51.c b/arch/arm/mach-mx5/clock-mx51.c
index dcca330..1fe40e1 100644
--- a/arch/arm/mach-mx5/clock-mx51.c
+++ b/arch/arm/mach-mx5/clock-mx51.c
@@ -16,6 +16,7 @@
#include <linux/io.h>
#include <asm/clkdev.h>
+#include <asm/div64.h>
#include <mach/hardware.h>
#include <mach/common.h>
diff --git a/arch/arm/plat-mxc/ehci.c b/arch/arm/plat-mxc/ehci.c
index cb0b638..2a86461 100644
--- a/arch/arm/plat-mxc/ehci.c
+++ b/arch/arm/plat-mxc/ehci.c
@@ -1,5 +1,6 @@
/*
* Copyright (c) 2009 Daniel Mack <[email protected]>
+ * Copyright (C) 2010 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
@@ -50,7 +51,26 @@
#define MX35_H1_TLL_BIT (1 << 5)
#define MX35_H1_USBTE_BIT (1 << 4)
-int mxc_set_usbcontrol(int port, unsigned int flags)
+#define MXC_OTG_OFFSET 0
+#define MXC_H1_OFFSET 0x200
+
+/* USB_CTRL */
+#define MXC_OTG_UCTRL_OWIE_BIT (1 << 27) /* OTG wakeup intr enable */
+#define MXC_OTG_UCTRL_OPM_BIT (1 << 24) /* OTG power mask */
+#define MXC_H1_UCTRL_H1UIE_BIT (1 << 12) /* Host1 ULPI interrupt enable */
+#define MXC_H1_UCTRL_H1WIE_BIT (1 << 11) /* HOST1 wakeup intr enable */
+#define MXC_H1_UCTRL_H1PM_BIT (1 << 8) /* HOST1 power mask */
+
+/* USB_PHY_CTRL_FUNC */
+#define MXC_OTG_PHYCTRL_OC_DIS_BIT (1 << 8) /* OTG Disable Overcurrent Event */
+#define MXC_H1_OC_DIS_BIT (1 << 5) /* UH1 Disable Overcurrent Event */
+
+#define MXC_USBCMD_OFFSET 0x140
+
+/* USBCMD */
+#define MXC_UCMD_ITC_NO_THRESHOLD_MASK (~(0xff << 16)) /* Interrupt Threshold Control */
+
+int mxc_initialize_usb_hw(int port, unsigned int flags)
{
unsigned int v;
#ifdef CONFIG_ARCH_MX3
@@ -186,9 +206,85 @@ int mxc_set_usbcontrol(int port, unsigned int flags)
return 0;
}
#endif /* CONFIG_MACH_MX27 */
+#ifdef CONFIG_ARCH_MX51
+ if (cpu_is_mx51()) {
+ void __iomem *usb_base;
+ u32 usbotg_base;
+ u32 usbother_base;
+ int ret = 0;
+
+ usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
+
+ switch (port) {
+ case 0: /* OTG port */
+ usbotg_base = usb_base + MXC_OTG_OFFSET;
+ break;
+ case 1: /* Host 1 port */
+ usbotg_base = usb_base + MXC_H1_OFFSET;
+ break;
+ default:
+ printk(KERN_ERR"%s no such port %d\n", __func__, port);
+ ret = -ENOENT;
+ goto error;
+ }
+ usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
+
+ switch (port) {
+ case 0: /*OTG port */
+ if (flags & MXC_EHCI_INTERNAL_PHY) {
+ v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v |= (MXC_OTG_PHYCTRL_OC_DIS_BIT | MXC_OTG_UCTRL_OPM_BIT); /* OC/USBPWR is not used */
+ else
+ v &= ~(MXC_OTG_PHYCTRL_OC_DIS_BIT | MXC_OTG_UCTRL_OPM_BIT); /* OC/USBPWR is used */
+ __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+
+ v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
+ if (flags & MXC_EHCI_WAKEUP_ENABLED)
+ v |= MXC_OTG_UCTRL_OWIE_BIT;/* OTG wakeup enable */
+ else
+ v &= ~MXC_OTG_UCTRL_OWIE_BIT;/* OTG wakeup disable */
+ __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
+ }
+ break;
+ case 1: /* Host 1 */
+ /*Host ULPI */
+ v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
+ if (flags & MXC_EHCI_WAKEUP_ENABLED)
+ v &= ~(MXC_H1_UCTRL_H1WIE_BIT | MXC_H1_UCTRL_H1UIE_BIT);/* HOST1 wakeup/ULPI intr disable */
+ else
+ v &= ~(MXC_H1_UCTRL_H1WIE_BIT | MXC_H1_UCTRL_H1UIE_BIT);/* HOST1 wakeup/ULPI intr disable */
+
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
+ else
+ v |= MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
+ __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
+
+ v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */
+ else
+ v |= MXC_H1_OC_DIS_BIT; /* OC is not used */
+ __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+
+ v = __raw_readl(usbotg_base + MXC_USBCMD_OFFSET);
+ if (flags & MXC_EHCI_ITC_NO_THRESHOLD)
+ /* Interrupt Threshold Control:Immediate (no threshold) */
+ v &= MXC_UCMD_ITC_NO_THRESHOLD_MASK;
+ __raw_writel(v, usbotg_base + MXC_USBCMD_OFFSET);
+ break;
+ }
+
+error:
+ iounmap(usb_base);
+ return ret;
+ }
+#endif
printk(KERN_WARNING
"%s() unable to setup USBCONTROL for this CPU\n", __func__);
return -EINVAL;
}
-EXPORT_SYMBOL(mxc_set_usbcontrol);
+EXPORT_SYMBOL(mxc_initialize_usb_hw);
diff --git a/arch/arm/plat-mxc/include/mach/mxc_ehci.h b/arch/arm/plat-mxc/include/mach/mxc_ehci.h
index 4b9b836..7fc5f99 100644
--- a/arch/arm/plat-mxc/include/mach/mxc_ehci.h
+++ b/arch/arm/plat-mxc/include/mach/mxc_ehci.h
@@ -25,6 +25,18 @@
#define MXC_EHCI_INTERNAL_PHY (1 << 7)
#define MXC_EHCI_IPPUE_DOWN (1 << 8)
#define MXC_EHCI_IPPUE_UP (1 << 9)
+#define MXC_EHCI_WAKEUP_ENABLED (1 << 10)
+#define MXC_EHCI_ITC_NO_THRESHOLD (1 << 11)
+
+#define MXC_USBCTRL_OFFSET 0
+#define MXC_USB_PHY_CTR_FUNC_OFFSET 0x8
+#define MXC_USB_PHY_CTR_FUNC2_OFFSET 0xc
+
+#define MX5_USBOTHER_REGS_OFFSET 0x800
+
+/* USB_PHY_CTRL_FUNC2*/
+#define MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK 0x3
+#define MX5_USB_UTMI_PHYCTRL1_PLLDIV_SHIFT 0
struct mxc_usbh_platform_data {
int (*init)(struct platform_device *pdev);
@@ -35,7 +47,7 @@ struct mxc_usbh_platform_data {
struct otg_transceiver *otg;
};
-int mxc_set_usbcontrol(int port, unsigned int flags);
+int mxc_initialize_usb_hw(int port, unsigned int flags);
#endif /* __INCLUDE_ASM_ARCH_MXC_EHCI_H */
diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index ead59f4..544ccfd 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -199,8 +199,8 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
writel(pdata->portsc, hcd->regs + PORTSC_OFFSET);
mdelay(10);
- /* setup USBCONTROL. */
- ret = mxc_set_usbcontrol(pdev->id, pdata->flags);
+ /* setup specific usb hw */
+ ret = mxc_initialize_usb_hw(pdev->id, pdata->flags);
if (ret < 0)
goto err_init;
--
1.6.0.4
From: Dinh Nguyen <[email protected]>
This patch is part of enabling USB for Freescale MX51 Babbage HW. This
patch adds device structures for USB Host1 and OTG port, and adds
clocking information for USB HW.
This patch applies to 2.6.34-rc5.
Signed-off-by: Dinh Nguyen <[email protected]>
---
arch/arm/mach-mx5/clock-mx51.c | 8 ++++++
arch/arm/mach-mx5/devices.c | 49 ++++++++++++++++++++++++++++++++++++++++
arch/arm/mach-mx5/devices.h | 2 +
3 files changed, 59 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-mx5/clock-mx51.c b/arch/arm/mach-mx5/clock-mx51.c
index 8f85f73..dcca330 100644
--- a/arch/arm/mach-mx5/clock-mx51.c
+++ b/arch/arm/mach-mx5/clock-mx51.c
@@ -761,6 +761,10 @@ DEFINE_CLOCK(gpt_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG9_OFFSET,
DEFINE_CLOCK(gpt_ipg_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG10_OFFSET,
NULL, NULL, &ipg_clk, NULL);
+/* USB */
+DEFINE_CLOCK(usboh3_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG14_OFFSET,
+ NULL, NULL, &pll3_sw_clk, NULL);
+
/* FEC */
DEFINE_CLOCK(fec_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG12_OFFSET,
NULL, NULL, &ipg_clk, NULL);
@@ -778,6 +782,10 @@ static struct clk_lookup lookups[] = {
_REGISTER_CLOCK("imx-uart.2", NULL, uart3_clk)
_REGISTER_CLOCK(NULL, "gpt", gpt_clk)
_REGISTER_CLOCK("fec.0", NULL, fec_clk)
+ _REGISTER_CLOCK("mxc-ehci.0", "usb", usboh3_clk)
+ _REGISTER_CLOCK("mxc-ehci.0", "usb_ahb", ahb_clk)
+ _REGISTER_CLOCK("mxc-ehci.1", "usb", usboh3_clk)
+ _REGISTER_CLOCK("mxc-ehci.1", "usb_ahb", ahb_clk)
};
static void clk_tree_init(void)
diff --git a/arch/arm/mach-mx5/devices.c b/arch/arm/mach-mx5/devices.c
index 5070ae1..e6262f3 100644
--- a/arch/arm/mach-mx5/devices.c
+++ b/arch/arm/mach-mx5/devices.c
@@ -11,6 +11,7 @@
*/
#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
#include <linux/gpio.h>
#include <mach/hardware.h>
#include <mach/imx-uart.h>
@@ -92,6 +93,54 @@ struct platform_device mxc_fec_device = {
.resource = mxc_fec_resources,
};
+static u64 usb_dma_mask = DMA_BIT_MASK(32);
+
+static struct resource usbotg_resources[] = {
+ {
+ .start = MX51_OTG_BASE_ADDR,
+ .end = MX51_OTG_BASE_ADDR + 0x1ff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = MX51_MXC_INT_USB_OTG,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device mxc_usbdr_host_device = {
+ .name = "mxc-ehci",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(usbotg_resources),
+ .resource = usbotg_resources,
+ .dev = {
+ .dma_mask = &usb_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+
+static struct resource usbh1_resources[] = {
+ {
+ .start = MX51_OTG_BASE_ADDR + 0x200,
+ .end = MX51_OTG_BASE_ADDR + 0x200 + 0x1ff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = MX51_MXC_INT_USB_H1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device mxc_usbh1_device = {
+ .name = "mxc-ehci",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(usbh1_resources),
+ .resource = usbh1_resources,
+ .dev = {
+ .dma_mask = &usb_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+
static struct mxc_gpio_port mxc_gpio_ports[] = {
{
.chip.label = "gpio-0",
diff --git a/arch/arm/mach-mx5/devices.h b/arch/arm/mach-mx5/devices.h
index f339ab8..95c45f9 100644
--- a/arch/arm/mach-mx5/devices.h
+++ b/arch/arm/mach-mx5/devices.h
@@ -2,3 +2,5 @@ extern struct platform_device mxc_uart_device0;
extern struct platform_device mxc_uart_device1;
extern struct platform_device mxc_uart_device2;
extern struct platform_device mxc_fec_device;
+extern struct platform_device mxc_usbdr_host_device;
+extern struct platform_device mxc_usbh1_device;
--
1.6.0.4