2010-08-26 02:05:22

by Mark F. Brown

[permalink] [raw]
Subject: [PATCH v2 1/1] pxa168: added initial support for TPO TD043MTEA1 LCD display on Aspenite

Signed-off-by: Mark F. Brown <[email protected]>
---
arch/arm/mach-mmp/aspenite.c | 60 +++++++++++++++++++++++++++++++
arch/arm/mach-mmp/include/mach/pxa168.h | 8 ++++
arch/arm/mach-mmp/pxa168.c | 4 ++
drivers/video/pxa168fb.c | 4 +-
4 files changed, 74 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c
index 0629394..9e1bd6b 100644
--- a/arch/arm/mach-mmp/aspenite.c
+++ b/arch/arm/mach-mmp/aspenite.c
@@ -23,6 +23,7 @@
#include <mach/mfp-pxa168.h>
#include <mach/pxa168.h>
#include <mach/gpio.h>
+#include <video/pxa168fb.h>

#include "common.h"

@@ -66,6 +67,36 @@ static unsigned long common_pin_config[] __initdata = {
GPIO115_I2S_BCLK,
GPIO116_I2S_RXD,
GPIO117_I2S_TXD,
+
+ /* LCD */
+ GPIO56_LCD_FCLK_RD,
+ GPIO57_LCD_LCLK_A0,
+ GPIO58_LCD_PCLK_WR,
+ GPIO59_LCD_DENA_BIAS,
+ GPIO60_LCD_DD0,
+ GPIO61_LCD_DD1,
+ GPIO62_LCD_DD2,
+ GPIO63_LCD_DD3,
+ GPIO64_LCD_DD4,
+ GPIO65_LCD_DD5,
+ GPIO66_LCD_DD6,
+ GPIO67_LCD_DD7,
+ GPIO68_LCD_DD8,
+ GPIO69_LCD_DD9,
+ GPIO70_LCD_DD10,
+ GPIO71_LCD_DD11,
+ GPIO72_LCD_DD12,
+ GPIO73_LCD_DD13,
+ GPIO74_LCD_DD14,
+ GPIO75_LCD_DD15,
+ GPIO76_LCD_DD16,
+ GPIO77_LCD_DD17,
+ GPIO78_LCD_DD18,
+ GPIO79_LCD_DD19,
+ GPIO80_LCD_DD20,
+ GPIO81_LCD_DD21,
+ GPIO82_LCD_DD22,
+ GPIO83_LCD_DD23,
};

static struct smc91x_platdata smc91x_info = {
@@ -134,6 +165,34 @@ static struct i2c_board_info aspenite_i2c_info[] __initdata = {
{ I2C_BOARD_INFO("wm8753", 0x1b), },
};

+static struct fb_videomode video_modes[] = {
+ [0] = {
+ .pixclock = 30120,
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .hsync_len = 1,
+ .left_margin = 215,
+ .right_margin = 40,
+ .vsync_len = 1,
+ .upper_margin = 34,
+ .lower_margin = 10,
+ .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
+ },
+};
+
+struct pxa168fb_mach_info aspenite_lcd_info = {
+ .id = "Graphic Frame",
+ .modes = video_modes,
+ .num_modes = ARRAY_SIZE(video_modes),
+ .pix_fmt = PIX_FMT_RGB565,
+ .io_pin_allocation_mode = PIN_MODE_DUMB_24,
+ .dumb_mode = DUMB_MODE_RGB888,
+ .active = 1,
+ .panel_rbswap = 0,
+ .invert_pixclock = 0,
+};
+
static void __init common_init(void)
{
mfp_config(ARRAY_AND_SIZE(common_pin_config));
@@ -143,6 +202,7 @@ static void __init common_init(void)
pxa168_add_twsi(1, NULL, ARRAY_AND_SIZE(aspenite_i2c_info));
pxa168_add_ssp(1);
pxa168_add_nand(&aspenite_nand_info);
+ pxa168_add_fb(&aspenite_lcd_info);

/* off-chip devices */
platform_device_register(&smc91x_device);
diff --git a/arch/arm/mach-mmp/include/mach/pxa168.h b/arch/arm/mach-mmp/include/mach/pxa168.h
index 27e1bc7..220738f 100644
--- a/arch/arm/mach-mmp/include/mach/pxa168.h
+++ b/arch/arm/mach-mmp/include/mach/pxa168.h
@@ -10,6 +10,7 @@ extern void __init pxa168_init_irq(void);
#include <mach/devices.h>
#include <plat/i2c.h>
#include <plat/pxa3xx_nand.h>
+#include <video/pxa168fb.h>

extern struct pxa_device_desc pxa168_device_uart1;
extern struct pxa_device_desc pxa168_device_uart2;
@@ -25,6 +26,7 @@ extern struct pxa_device_desc pxa168_device_ssp3;
extern struct pxa_device_desc pxa168_device_ssp4;
extern struct pxa_device_desc pxa168_device_ssp5;
extern struct pxa_device_desc pxa168_device_nand;
+extern struct pxa_device_desc pxa168_device_fb;

static inline int pxa168_add_uart(int id)
{
@@ -97,4 +99,10 @@ static inline int pxa168_add_nand(struct pxa3xx_nand_platform_data *info)
{
return pxa_register_device(&pxa168_device_nand, info, sizeof(*info));
}
+
+static inline int pxa168_add_fb(struct pxa168fb_mach_info *mi)
+{
+ return pxa_register_device(&pxa168_device_fb, mi, sizeof(*mi));
+}
+
#endif /* __ASM_MACH_PXA168_H */
diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
index 652ae66..886eadb 100644
--- a/arch/arm/mach-mmp/pxa168.c
+++ b/arch/arm/mach-mmp/pxa168.c
@@ -25,6 +25,7 @@
#include <mach/dma.h>
#include <mach/devices.h>
#include <mach/mfp.h>
+#include <video/pxa168fb.h>

#include "common.h"
#include "clock.h"
@@ -79,6 +80,7 @@ static APBC_CLK(ssp4, PXA168_SSP4, 4, 0);
static APBC_CLK(ssp5, PXA168_SSP5, 4, 0);

static APMU_CLK(nand, NAND, 0x01db, 208000000);
+static APMU_CLK(lcd, LCD, 0x7f, 312000000);

/* device and clock bindings */
static struct clk_lookup pxa168_clkregs[] = {
@@ -96,6 +98,7 @@ static struct clk_lookup pxa168_clkregs[] = {
INIT_CLKREG(&clk_ssp4, "pxa168-ssp.3", NULL),
INIT_CLKREG(&clk_ssp5, "pxa168-ssp.4", NULL),
INIT_CLKREG(&clk_nand, "pxa3xx-nand", NULL),
+ INIT_CLKREG(&clk_lcd, "pxa168-fb", NULL),
};

static int __init pxa168_init(void)
@@ -147,3 +150,4 @@ PXA168_DEVICE(ssp2, "pxa168-ssp", 1, SSP2, 0xd401c000, 0x40, 54, 55);
PXA168_DEVICE(ssp3, "pxa168-ssp", 2, SSP3, 0xd401f000, 0x40, 56, 57);
PXA168_DEVICE(ssp4, "pxa168-ssp", 3, SSP4, 0xd4020000, 0x40, 58, 59);
PXA168_DEVICE(ssp5, "pxa168-ssp", 4, SSP5, 0xd4021000, 0x40, 60, 61);
+PXA168_DEVICE(fb, "pxa168-fb", -1, LCD, 0xd420b000, 0x1c8);
diff --git a/drivers/video/pxa168fb.c b/drivers/video/pxa168fb.c
index c91a7f7..d3e597e 100644
--- a/drivers/video/pxa168fb.c
+++ b/drivers/video/pxa168fb.c
@@ -559,7 +559,7 @@ static struct fb_ops pxa168fb_ops = {
.fb_imageblit = cfb_imageblit,
};

-static int __init pxa168fb_init_mode(struct fb_info *info,
+static int pxa168fb_init_mode(struct fb_info *info,
struct pxa168fb_mach_info *mi)
{
struct pxa168fb_info *fbi = info->par;
@@ -599,7 +599,7 @@ static int __init pxa168fb_init_mode(struct fb_info *info,
return ret;
}

-static int __init pxa168fb_probe(struct platform_device *pdev)
+static int pxa168fb_probe(struct platform_device *pdev)
{
struct pxa168fb_mach_info *mi;
struct fb_info *info = 0;
--
1.7.0.4


2010-08-26 02:27:26

by Marek Vasut

[permalink] [raw]
Subject: Re: [PATCH v2 1/1] pxa168: added initial support for TPO TD043MTEA1 LCD display on Aspenite

Dne Čt 26. srpna 2010 04:04:52 Mark F. Brown napsal(a):
> Signed-off-by: Mark F. Brown <[email protected]>
> ---
> arch/arm/mach-mmp/aspenite.c | 60
> +++++++++++++++++++++++++++++++ arch/arm/mach-mmp/include/mach/pxa168.h |
> 8 ++++
> arch/arm/mach-mmp/pxa168.c | 4 ++
> drivers/video/pxa168fb.c | 4 +-
> 4 files changed, 74 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c
> index 0629394..9e1bd6b 100644
> --- a/arch/arm/mach-mmp/aspenite.c
> +++ b/arch/arm/mach-mmp/aspenite.c
> @@ -23,6 +23,7 @@
> #include <mach/mfp-pxa168.h>
> #include <mach/pxa168.h>
> #include <mach/gpio.h>
> +#include <video/pxa168fb.h>
>
> #include "common.h"
>
> @@ -66,6 +67,36 @@ static unsigned long common_pin_config[] __initdata = {
> GPIO115_I2S_BCLK,
> GPIO116_I2S_RXD,
> GPIO117_I2S_TXD,
> +
> + /* LCD */
> + GPIO56_LCD_FCLK_RD,
> + GPIO57_LCD_LCLK_A0,
> + GPIO58_LCD_PCLK_WR,
> + GPIO59_LCD_DENA_BIAS,
> + GPIO60_LCD_DD0,
> + GPIO61_LCD_DD1,
> + GPIO62_LCD_DD2,
> + GPIO63_LCD_DD3,
> + GPIO64_LCD_DD4,
> + GPIO65_LCD_DD5,
> + GPIO66_LCD_DD6,
> + GPIO67_LCD_DD7,
> + GPIO68_LCD_DD8,
> + GPIO69_LCD_DD9,
> + GPIO70_LCD_DD10,
> + GPIO71_LCD_DD11,
> + GPIO72_LCD_DD12,
> + GPIO73_LCD_DD13,
> + GPIO74_LCD_DD14,
> + GPIO75_LCD_DD15,
> + GPIO76_LCD_DD16,
> + GPIO77_LCD_DD17,
> + GPIO78_LCD_DD18,
> + GPIO79_LCD_DD19,
> + GPIO80_LCD_DD20,
> + GPIO81_LCD_DD21,
> + GPIO82_LCD_DD22,
> + GPIO83_LCD_DD23,
> };
>
> static struct smc91x_platdata smc91x_info = {
> @@ -134,6 +165,34 @@ static struct i2c_board_info aspenite_i2c_info[]
> __initdata = { { I2C_BOARD_INFO("wm8753", 0x1b), },
> };
>
> +static struct fb_videomode video_modes[] = {
> + [0] = {
> + .pixclock = 30120,
> + .refresh = 60,
> + .xres = 800,
> + .yres = 480,
> + .hsync_len = 1,
> + .left_margin = 215,
> + .right_margin = 40,
> + .vsync_len = 1,
> + .upper_margin = 34,
> + .lower_margin = 10,
> + .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
> + },
> +};
> +
> +struct pxa168fb_mach_info aspenite_lcd_info = {
> + .id = "Graphic Frame",
> + .modes = video_modes,
> + .num_modes = ARRAY_SIZE(video_modes),
> + .pix_fmt = PIX_FMT_RGB565,
> + .io_pin_allocation_mode = PIN_MODE_DUMB_24,
> + .dumb_mode = DUMB_MODE_RGB888,
> + .active = 1,
> + .panel_rbswap = 0,
> + .invert_pixclock = 0,
> +};
> +
> static void __init common_init(void)
> {
> mfp_config(ARRAY_AND_SIZE(common_pin_config));
> @@ -143,6 +202,7 @@ static void __init common_init(void)
> pxa168_add_twsi(1, NULL, ARRAY_AND_SIZE(aspenite_i2c_info));
> pxa168_add_ssp(1);
> pxa168_add_nand(&aspenite_nand_info);
> + pxa168_add_fb(&aspenite_lcd_info);
>
> /* off-chip devices */
> platform_device_register(&smc91x_device);



----------------------------------------------
^--- one patch above
SNIP, please split into two patches
v--- another patch below
----------------------------------------------




> diff --git a/arch/arm/mach-mmp/include/mach/pxa168.h
> b/arch/arm/mach-mmp/include/mach/pxa168.h index 27e1bc7..220738f 100644
> --- a/arch/arm/mach-mmp/include/mach/pxa168.h
> +++ b/arch/arm/mach-mmp/include/mach/pxa168.h
> @@ -10,6 +10,7 @@ extern void __init pxa168_init_irq(void);
> #include <mach/devices.h>
> #include <plat/i2c.h>
> #include <plat/pxa3xx_nand.h>
> +#include <video/pxa168fb.h>
>
> extern struct pxa_device_desc pxa168_device_uart1;
> extern struct pxa_device_desc pxa168_device_uart2;
> @@ -25,6 +26,7 @@ extern struct pxa_device_desc pxa168_device_ssp3;
> extern struct pxa_device_desc pxa168_device_ssp4;
> extern struct pxa_device_desc pxa168_device_ssp5;
> extern struct pxa_device_desc pxa168_device_nand;
> +extern struct pxa_device_desc pxa168_device_fb;
>
> static inline int pxa168_add_uart(int id)
> {
> @@ -97,4 +99,10 @@ static inline int pxa168_add_nand(struct
> pxa3xx_nand_platform_data *info) {
> return pxa_register_device(&pxa168_device_nand, info, sizeof(*info));
> }
> +
> +static inline int pxa168_add_fb(struct pxa168fb_mach_info *mi)
> +{
> + return pxa_register_device(&pxa168_device_fb, mi, sizeof(*mi));
> +}
> +
> #endif /* __ASM_MACH_PXA168_H */
> diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
> index 652ae66..886eadb 100644
> --- a/arch/arm/mach-mmp/pxa168.c
> +++ b/arch/arm/mach-mmp/pxa168.c
> @@ -25,6 +25,7 @@
> #include <mach/dma.h>
> #include <mach/devices.h>
> #include <mach/mfp.h>
> +#include <video/pxa168fb.h>
>
> #include "common.h"
> #include "clock.h"
> @@ -79,6 +80,7 @@ static APBC_CLK(ssp4, PXA168_SSP4, 4, 0);
> static APBC_CLK(ssp5, PXA168_SSP5, 4, 0);
>
> static APMU_CLK(nand, NAND, 0x01db, 208000000);
> +static APMU_CLK(lcd, LCD, 0x7f, 312000000);
>
> /* device and clock bindings */
> static struct clk_lookup pxa168_clkregs[] = {
> @@ -96,6 +98,7 @@ static struct clk_lookup pxa168_clkregs[] = {
> INIT_CLKREG(&clk_ssp4, "pxa168-ssp.3", NULL),
> INIT_CLKREG(&clk_ssp5, "pxa168-ssp.4", NULL),
> INIT_CLKREG(&clk_nand, "pxa3xx-nand", NULL),
> + INIT_CLKREG(&clk_lcd, "pxa168-fb", NULL),
> };
>
> static int __init pxa168_init(void)
> @@ -147,3 +150,4 @@ PXA168_DEVICE(ssp2, "pxa168-ssp", 1, SSP2, 0xd401c000,
> 0x40, 54, 55); PXA168_DEVICE(ssp3, "pxa168-ssp", 2, SSP3, 0xd401f000,
> 0x40, 56, 57); PXA168_DEVICE(ssp4, "pxa168-ssp", 3, SSP4, 0xd4020000,
> 0x40, 58, 59); PXA168_DEVICE(ssp5, "pxa168-ssp", 4, SSP5, 0xd4021000,
> 0x40, 60, 61); +PXA168_DEVICE(fb, "pxa168-fb", -1, LCD, 0xd420b000,
> 0x1c8);
> diff --git a/drivers/video/pxa168fb.c b/drivers/video/pxa168fb.c
> index c91a7f7..d3e597e 100644
> --- a/drivers/video/pxa168fb.c
> +++ b/drivers/video/pxa168fb.c
> @@ -559,7 +559,7 @@ static struct fb_ops pxa168fb_ops = {
> .fb_imageblit = cfb_imageblit,
> };
>
> -static int __init pxa168fb_init_mode(struct fb_info *info,
> +static int pxa168fb_init_mode(struct fb_info *info,
> struct pxa168fb_mach_info *mi)

Why do you remove __init from it ?
> {
> struct pxa168fb_info *fbi = info->par;
> @@ -599,7 +599,7 @@ static int __init pxa168fb_init_mode(struct fb_info
> *info, return ret;
> }
>
> -static int __init pxa168fb_probe(struct platform_device *pdev)
> +static int pxa168fb_probe(struct platform_device *pdev)

Why do you remove __init from it ? (DTTO)
> {
> struct pxa168fb_mach_info *mi;
> struct fb_info *info = 0;

Cheers

2010-08-26 03:44:52

by Mark F. Brown

[permalink] [raw]
Subject: Re: [PATCH v2 1/1] pxa168: added initial support for TPO TD043MTEA1 LCD display on Aspenite

On Wed, Aug 25, 2010 at 10:26 PM, Marek Vasut <[email protected]> wrote:
> Dne ?t 26. srpna 2010 04:04:52 Mark F. Brown napsal(a):
>> Signed-off-by: Mark F. Brown <[email protected]>
>> ---
>> ?arch/arm/mach-mmp/aspenite.c ? ? ? ? ? ?| ? 60
>> +++++++++++++++++++++++++++++++ arch/arm/mach-mmp/include/mach/pxa168.h |
>> ? 8 ++++
>> ?arch/arm/mach-mmp/pxa168.c ? ? ? ? ? ? ?| ? ?4 ++
>> ?drivers/video/pxa168fb.c ? ? ? ? ? ? ? ?| ? ?4 +-
>> ?4 files changed, 74 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c
>> index 0629394..9e1bd6b 100644
>> --- a/arch/arm/mach-mmp/aspenite.c
>> +++ b/arch/arm/mach-mmp/aspenite.c
>> @@ -23,6 +23,7 @@
>> ?#include <mach/mfp-pxa168.h>
>> ?#include <mach/pxa168.h>
>> ?#include <mach/gpio.h>
>> +#include <video/pxa168fb.h>
>>
>> ?#include "common.h"
>>
>> @@ -66,6 +67,36 @@ static unsigned long common_pin_config[] __initdata = {
>> ? ? ? GPIO115_I2S_BCLK,
>> ? ? ? GPIO116_I2S_RXD,
>> ? ? ? GPIO117_I2S_TXD,
>> +
>> + ? ? /* LCD */
>> + ? ? GPIO56_LCD_FCLK_RD,
>> + ? ? GPIO57_LCD_LCLK_A0,
>> + ? ? GPIO58_LCD_PCLK_WR,
>> + ? ? GPIO59_LCD_DENA_BIAS,
>> + ? ? GPIO60_LCD_DD0,
>> + ? ? GPIO61_LCD_DD1,
>> + ? ? GPIO62_LCD_DD2,
>> + ? ? GPIO63_LCD_DD3,
>> + ? ? GPIO64_LCD_DD4,
>> + ? ? GPIO65_LCD_DD5,
>> + ? ? GPIO66_LCD_DD6,
>> + ? ? GPIO67_LCD_DD7,
>> + ? ? GPIO68_LCD_DD8,
>> + ? ? GPIO69_LCD_DD9,
>> + ? ? GPIO70_LCD_DD10,
>> + ? ? GPIO71_LCD_DD11,
>> + ? ? GPIO72_LCD_DD12,
>> + ? ? GPIO73_LCD_DD13,
>> + ? ? GPIO74_LCD_DD14,
>> + ? ? GPIO75_LCD_DD15,
>> + ? ? GPIO76_LCD_DD16,
>> + ? ? GPIO77_LCD_DD17,
>> + ? ? GPIO78_LCD_DD18,
>> + ? ? GPIO79_LCD_DD19,
>> + ? ? GPIO80_LCD_DD20,
>> + ? ? GPIO81_LCD_DD21,
>> + ? ? GPIO82_LCD_DD22,
>> + ? ? GPIO83_LCD_DD23,
>> ?};
>>
>> ?static struct smc91x_platdata smc91x_info = {
>> @@ -134,6 +165,34 @@ static struct i2c_board_info aspenite_i2c_info[]
>> __initdata = { { I2C_BOARD_INFO("wm8753", 0x1b), },
>> ?};
>>
>> +static struct fb_videomode video_modes[] = {
>> + ? ? [0] = {
>> + ? ? ? ? ? ? .pixclock ? ? ? = 30120,
>> + ? ? ? ? ? ? .refresh ? ? ? ?= 60,
>> + ? ? ? ? ? ? .xres ? ? ? ? ? = 800,
>> + ? ? ? ? ? ? .yres ? ? ? ? ? = 480,
>> + ? ? ? ? ? ? .hsync_len ? ? ?= 1,
>> + ? ? ? ? ? ? .left_margin ? ?= 215,
>> + ? ? ? ? ? ? .right_margin ? = 40,
>> + ? ? ? ? ? ? .vsync_len ? ? ?= 1,
>> + ? ? ? ? ? ? .upper_margin ? = 34,
>> + ? ? ? ? ? ? .lower_margin ? = 10,
>> + ? ? ? ? ? ? .sync ? ? ? ? ? = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
>> + ? ? },
>> +};
>> +
>> +struct pxa168fb_mach_info aspenite_lcd_info = {
>> + ? ? .id ? ? ? ? ? ? ? ? ? ? = "Graphic Frame",
>> + ? ? .modes ? ? ? ? ? ? ? ? ?= video_modes,
>> + ? ? .num_modes ? ? ? ? ? ? ?= ARRAY_SIZE(video_modes),
>> + ? ? .pix_fmt ? ? ? ? ? ? ? ?= PIX_FMT_RGB565,
>> + ? ? .io_pin_allocation_mode = PIN_MODE_DUMB_24,
>> + ? ? .dumb_mode ? ? ? ? ? ? ?= DUMB_MODE_RGB888,
>> + ? ? .active ? ? ? ? ? ? ? ? = 1,
>> + ? ? .panel_rbswap ? ? ? ? ? = 0,
>> + ? ? .invert_pixclock ? ? ? ?= 0,
>> +};
>> +
>> ?static void __init common_init(void)
>> ?{
>> ? ? ? mfp_config(ARRAY_AND_SIZE(common_pin_config));
>> @@ -143,6 +202,7 @@ static void __init common_init(void)
>> ? ? ? pxa168_add_twsi(1, NULL, ARRAY_AND_SIZE(aspenite_i2c_info));
>> ? ? ? pxa168_add_ssp(1);
>> ? ? ? pxa168_add_nand(&aspenite_nand_info);
>> + ? ? pxa168_add_fb(&aspenite_lcd_info);
>>
>> ? ? ? /* off-chip devices */
>> ? ? ? platform_device_register(&smc91x_device);
>
>
>
> ----------------------------------------------
> ^--- one patch above
> SNIP, please split into two patches
> v--- another patch below
> ----------------------------------------------
>
>
>
>
>> diff --git a/arch/arm/mach-mmp/include/mach/pxa168.h
>> b/arch/arm/mach-mmp/include/mach/pxa168.h index 27e1bc7..220738f 100644
>> --- a/arch/arm/mach-mmp/include/mach/pxa168.h
>> +++ b/arch/arm/mach-mmp/include/mach/pxa168.h
>> @@ -10,6 +10,7 @@ extern void __init pxa168_init_irq(void);
>> ?#include <mach/devices.h>
>> ?#include <plat/i2c.h>
>> ?#include <plat/pxa3xx_nand.h>
>> +#include <video/pxa168fb.h>
>>
>> ?extern struct pxa_device_desc pxa168_device_uart1;
>> ?extern struct pxa_device_desc pxa168_device_uart2;
>> @@ -25,6 +26,7 @@ extern struct pxa_device_desc pxa168_device_ssp3;
>> ?extern struct pxa_device_desc pxa168_device_ssp4;
>> ?extern struct pxa_device_desc pxa168_device_ssp5;
>> ?extern struct pxa_device_desc pxa168_device_nand;
>> +extern struct pxa_device_desc pxa168_device_fb;
>>
>> ?static inline int pxa168_add_uart(int id)
>> ?{
>> @@ -97,4 +99,10 @@ static inline int pxa168_add_nand(struct
>> pxa3xx_nand_platform_data *info) {
>> ? ? ? return pxa_register_device(&pxa168_device_nand, info, sizeof(*info));
>> ?}
>> +
>> +static inline int pxa168_add_fb(struct pxa168fb_mach_info *mi)
>> +{
>> + ? ? return pxa_register_device(&pxa168_device_fb, mi, sizeof(*mi));
>> +}
>> +
>> ?#endif /* __ASM_MACH_PXA168_H */
>> diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
>> index 652ae66..886eadb 100644
>> --- a/arch/arm/mach-mmp/pxa168.c
>> +++ b/arch/arm/mach-mmp/pxa168.c
>> @@ -25,6 +25,7 @@
>> ?#include <mach/dma.h>
>> ?#include <mach/devices.h>
>> ?#include <mach/mfp.h>
>> +#include <video/pxa168fb.h>
>>
>> ?#include "common.h"
>> ?#include "clock.h"
>> @@ -79,6 +80,7 @@ static APBC_CLK(ssp4, PXA168_SSP4, 4, 0);
>> ?static APBC_CLK(ssp5, PXA168_SSP5, 4, 0);
>>
>> ?static APMU_CLK(nand, NAND, 0x01db, 208000000);
>> +static APMU_CLK(lcd, LCD, 0x7f, 312000000);
>>
>> ?/* device and clock bindings */
>> ?static struct clk_lookup pxa168_clkregs[] = {
>> @@ -96,6 +98,7 @@ static struct clk_lookup pxa168_clkregs[] = {
>> ? ? ? INIT_CLKREG(&clk_ssp4, "pxa168-ssp.3", NULL),
>> ? ? ? INIT_CLKREG(&clk_ssp5, "pxa168-ssp.4", NULL),
>> ? ? ? INIT_CLKREG(&clk_nand, "pxa3xx-nand", NULL),
>> + ? ? INIT_CLKREG(&clk_lcd, "pxa168-fb", NULL),
>> ?};
>>
>> ?static int __init pxa168_init(void)
>> @@ -147,3 +150,4 @@ PXA168_DEVICE(ssp2, "pxa168-ssp", 1, SSP2, 0xd401c000,
>> 0x40, 54, 55); PXA168_DEVICE(ssp3, "pxa168-ssp", 2, SSP3, 0xd401f000,
>> 0x40, 56, 57); PXA168_DEVICE(ssp4, "pxa168-ssp", 3, SSP4, 0xd4020000,
>> 0x40, 58, 59); PXA168_DEVICE(ssp5, "pxa168-ssp", 4, SSP5, 0xd4021000,
>> 0x40, 60, 61); +PXA168_DEVICE(fb, "pxa168-fb", -1, LCD, 0xd420b000,
>> 0x1c8);
>> diff --git a/drivers/video/pxa168fb.c b/drivers/video/pxa168fb.c
>> index c91a7f7..d3e597e 100644
>> --- a/drivers/video/pxa168fb.c
>> +++ b/drivers/video/pxa168fb.c
>> @@ -559,7 +559,7 @@ static struct fb_ops pxa168fb_ops = {
>> ? ? ? .fb_imageblit ? = cfb_imageblit,
>> ?};
>>
>> -static int __init pxa168fb_init_mode(struct fb_info *info,
>> +static int pxa168fb_init_mode(struct fb_info *info,
>> ? ? ? ? ? ? ? ? ? ? ? ? ? ? struct pxa168fb_mach_info *mi)
>
> Why do you remove __init from it ?
>> ?{
>> ? ? ? struct pxa168fb_info *fbi = info->par;
>> @@ -599,7 +599,7 @@ static int __init pxa168fb_init_mode(struct fb_info
>> *info, return ret;
>> ?}
>>
>> -static int __init pxa168fb_probe(struct platform_device *pdev)
>> +static int pxa168fb_probe(struct platform_device *pdev)
>
> Why do you remove __init from it ? (DTTO)
>> ?{
>> ? ? ? struct pxa168fb_mach_info *mi;
>> ? ? ? struct fb_info *info = 0;
>
> Cheers
>

Hi Marek,

1) I removed the __init because it was causing a section mismatch
warning wth this kernel. Since pxa168fb_probe() is calling
pxa168fb_init_mode(), I cannot declare pxa168fb_init_mode() as an
__init function. If pxa168fb_probe gets called after the __init
section is wiped then it will attempt to run the deleted
pxa168fb_init_mode() code.

WARNING: vmlinux.o(.data+0x17984): Section mismatch in reference from
the variable pxa168fb_driver to the function
.init.text:pxa168fb_probe()
The variable pxa168fb_driver references
the function __init pxa168fb_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,


2) What is the logic behind the delineation between patch files? I
cannot build patch #1 without patch #2 based on how you defined the
split. I need all of it in order to function.

-- Mark

2010-08-26 03:57:15

by Haojian Zhuang

[permalink] [raw]
Subject: Re: [PATCH v2 1/1] pxa168: added initial support for TPO TD043MTEA1 LCD display on Aspenite

2010/8/26 Mark F. Brown <[email protected]>:
> On Wed, Aug 25, 2010 at 10:26 PM, Marek Vasut <[email protected]> wrote:
>> Dne ?t 26. srpna 2010 04:04:52 Mark F. Brown napsal(a):
>>> Signed-off-by: Mark F. Brown <[email protected]>
>>> ---
>>> ?arch/arm/mach-mmp/aspenite.c ? ? ? ? ? ?| ? 60
>>> +++++++++++++++++++++++++++++++ arch/arm/mach-mmp/include/mach/pxa168.h |
>>> ? 8 ++++
>>> ?arch/arm/mach-mmp/pxa168.c ? ? ? ? ? ? ?| ? ?4 ++
>>> ?drivers/video/pxa168fb.c ? ? ? ? ? ? ? ?| ? ?4 +-
>>> ?4 files changed, 74 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c
>>> index 0629394..9e1bd6b 100644
>>> --- a/arch/arm/mach-mmp/aspenite.c
>>> +++ b/arch/arm/mach-mmp/aspenite.c
>>> @@ -23,6 +23,7 @@
>>> ?#include <mach/mfp-pxa168.h>
>>> ?#include <mach/pxa168.h>
>>> ?#include <mach/gpio.h>
>>> +#include <video/pxa168fb.h>
>>>
>>> ?#include "common.h"
>>>
>>> @@ -66,6 +67,36 @@ static unsigned long common_pin_config[] __initdata = {
>>> ? ? ? GPIO115_I2S_BCLK,
>>> ? ? ? GPIO116_I2S_RXD,
>>> ? ? ? GPIO117_I2S_TXD,
>>> +
>>> + ? ? /* LCD */
>>> + ? ? GPIO56_LCD_FCLK_RD,
>>> + ? ? GPIO57_LCD_LCLK_A0,
>>> + ? ? GPIO58_LCD_PCLK_WR,
>>> + ? ? GPIO59_LCD_DENA_BIAS,
>>> + ? ? GPIO60_LCD_DD0,
>>> + ? ? GPIO61_LCD_DD1,
>>> + ? ? GPIO62_LCD_DD2,
>>> + ? ? GPIO63_LCD_DD3,
>>> + ? ? GPIO64_LCD_DD4,
>>> + ? ? GPIO65_LCD_DD5,
>>> + ? ? GPIO66_LCD_DD6,
>>> + ? ? GPIO67_LCD_DD7,
>>> + ? ? GPIO68_LCD_DD8,
>>> + ? ? GPIO69_LCD_DD9,
>>> + ? ? GPIO70_LCD_DD10,
>>> + ? ? GPIO71_LCD_DD11,
>>> + ? ? GPIO72_LCD_DD12,
>>> + ? ? GPIO73_LCD_DD13,
>>> + ? ? GPIO74_LCD_DD14,
>>> + ? ? GPIO75_LCD_DD15,
>>> + ? ? GPIO76_LCD_DD16,
>>> + ? ? GPIO77_LCD_DD17,
>>> + ? ? GPIO78_LCD_DD18,
>>> + ? ? GPIO79_LCD_DD19,
>>> + ? ? GPIO80_LCD_DD20,
>>> + ? ? GPIO81_LCD_DD21,
>>> + ? ? GPIO82_LCD_DD22,
>>> + ? ? GPIO83_LCD_DD23,
>>> ?};
>>>
>>> ?static struct smc91x_platdata smc91x_info = {
>>> @@ -134,6 +165,34 @@ static struct i2c_board_info aspenite_i2c_info[]
>>> __initdata = { { I2C_BOARD_INFO("wm8753", 0x1b), },
>>> ?};
>>>
>>> +static struct fb_videomode video_modes[] = {
>>> + ? ? [0] = {
>>> + ? ? ? ? ? ? .pixclock ? ? ? = 30120,
>>> + ? ? ? ? ? ? .refresh ? ? ? ?= 60,
>>> + ? ? ? ? ? ? .xres ? ? ? ? ? = 800,
>>> + ? ? ? ? ? ? .yres ? ? ? ? ? = 480,
>>> + ? ? ? ? ? ? .hsync_len ? ? ?= 1,
>>> + ? ? ? ? ? ? .left_margin ? ?= 215,
>>> + ? ? ? ? ? ? .right_margin ? = 40,
>>> + ? ? ? ? ? ? .vsync_len ? ? ?= 1,
>>> + ? ? ? ? ? ? .upper_margin ? = 34,
>>> + ? ? ? ? ? ? .lower_margin ? = 10,
>>> + ? ? ? ? ? ? .sync ? ? ? ? ? = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
>>> + ? ? },
>>> +};
>>> +
>>> +struct pxa168fb_mach_info aspenite_lcd_info = {
>>> + ? ? .id ? ? ? ? ? ? ? ? ? ? = "Graphic Frame",
>>> + ? ? .modes ? ? ? ? ? ? ? ? ?= video_modes,
>>> + ? ? .num_modes ? ? ? ? ? ? ?= ARRAY_SIZE(video_modes),
>>> + ? ? .pix_fmt ? ? ? ? ? ? ? ?= PIX_FMT_RGB565,
>>> + ? ? .io_pin_allocation_mode = PIN_MODE_DUMB_24,
>>> + ? ? .dumb_mode ? ? ? ? ? ? ?= DUMB_MODE_RGB888,
>>> + ? ? .active ? ? ? ? ? ? ? ? = 1,
>>> + ? ? .panel_rbswap ? ? ? ? ? = 0,
>>> + ? ? .invert_pixclock ? ? ? ?= 0,
>>> +};
>>> +
>>> ?static void __init common_init(void)
>>> ?{
>>> ? ? ? mfp_config(ARRAY_AND_SIZE(common_pin_config));
>>> @@ -143,6 +202,7 @@ static void __init common_init(void)
>>> ? ? ? pxa168_add_twsi(1, NULL, ARRAY_AND_SIZE(aspenite_i2c_info));
>>> ? ? ? pxa168_add_ssp(1);
>>> ? ? ? pxa168_add_nand(&aspenite_nand_info);
>>> + ? ? pxa168_add_fb(&aspenite_lcd_info);
>>>
>>> ? ? ? /* off-chip devices */
>>> ? ? ? platform_device_register(&smc91x_device);
>>
>>
>>
>> ----------------------------------------------
>> ^--- one patch above
>> SNIP, please split into two patches
>> v--- another patch below
>> ----------------------------------------------
>>
>>
>>
>>
>>> diff --git a/arch/arm/mach-mmp/include/mach/pxa168.h
>>> b/arch/arm/mach-mmp/include/mach/pxa168.h index 27e1bc7..220738f 100644
>>> --- a/arch/arm/mach-mmp/include/mach/pxa168.h
>>> +++ b/arch/arm/mach-mmp/include/mach/pxa168.h
>>> @@ -10,6 +10,7 @@ extern void __init pxa168_init_irq(void);
>>> ?#include <mach/devices.h>
>>> ?#include <plat/i2c.h>
>>> ?#include <plat/pxa3xx_nand.h>
>>> +#include <video/pxa168fb.h>
>>>
>>> ?extern struct pxa_device_desc pxa168_device_uart1;
>>> ?extern struct pxa_device_desc pxa168_device_uart2;
>>> @@ -25,6 +26,7 @@ extern struct pxa_device_desc pxa168_device_ssp3;
>>> ?extern struct pxa_device_desc pxa168_device_ssp4;
>>> ?extern struct pxa_device_desc pxa168_device_ssp5;
>>> ?extern struct pxa_device_desc pxa168_device_nand;
>>> +extern struct pxa_device_desc pxa168_device_fb;
>>>
>>> ?static inline int pxa168_add_uart(int id)
>>> ?{
>>> @@ -97,4 +99,10 @@ static inline int pxa168_add_nand(struct
>>> pxa3xx_nand_platform_data *info) {
>>> ? ? ? return pxa_register_device(&pxa168_device_nand, info, sizeof(*info));
>>> ?}
>>> +
>>> +static inline int pxa168_add_fb(struct pxa168fb_mach_info *mi)
>>> +{
>>> + ? ? return pxa_register_device(&pxa168_device_fb, mi, sizeof(*mi));
>>> +}
>>> +
>>> ?#endif /* __ASM_MACH_PXA168_H */
>>> diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
>>> index 652ae66..886eadb 100644
>>> --- a/arch/arm/mach-mmp/pxa168.c
>>> +++ b/arch/arm/mach-mmp/pxa168.c
>>> @@ -25,6 +25,7 @@
>>> ?#include <mach/dma.h>
>>> ?#include <mach/devices.h>
>>> ?#include <mach/mfp.h>
>>> +#include <video/pxa168fb.h>
>>>
>>> ?#include "common.h"
>>> ?#include "clock.h"
>>> @@ -79,6 +80,7 @@ static APBC_CLK(ssp4, PXA168_SSP4, 4, 0);
>>> ?static APBC_CLK(ssp5, PXA168_SSP5, 4, 0);
>>>
>>> ?static APMU_CLK(nand, NAND, 0x01db, 208000000);
>>> +static APMU_CLK(lcd, LCD, 0x7f, 312000000);
>>>
>>> ?/* device and clock bindings */
>>> ?static struct clk_lookup pxa168_clkregs[] = {
>>> @@ -96,6 +98,7 @@ static struct clk_lookup pxa168_clkregs[] = {
>>> ? ? ? INIT_CLKREG(&clk_ssp4, "pxa168-ssp.3", NULL),
>>> ? ? ? INIT_CLKREG(&clk_ssp5, "pxa168-ssp.4", NULL),
>>> ? ? ? INIT_CLKREG(&clk_nand, "pxa3xx-nand", NULL),
>>> + ? ? INIT_CLKREG(&clk_lcd, "pxa168-fb", NULL),
>>> ?};
>>>
>>> ?static int __init pxa168_init(void)
>>> @@ -147,3 +150,4 @@ PXA168_DEVICE(ssp2, "pxa168-ssp", 1, SSP2, 0xd401c000,
>>> 0x40, 54, 55); PXA168_DEVICE(ssp3, "pxa168-ssp", 2, SSP3, 0xd401f000,
>>> 0x40, 56, 57); PXA168_DEVICE(ssp4, "pxa168-ssp", 3, SSP4, 0xd4020000,
>>> 0x40, 58, 59); PXA168_DEVICE(ssp5, "pxa168-ssp", 4, SSP5, 0xd4021000,
>>> 0x40, 60, 61); +PXA168_DEVICE(fb, "pxa168-fb", -1, LCD, 0xd420b000,
>>> 0x1c8);
>>> diff --git a/drivers/video/pxa168fb.c b/drivers/video/pxa168fb.c
>>> index c91a7f7..d3e597e 100644
>>> --- a/drivers/video/pxa168fb.c
>>> +++ b/drivers/video/pxa168fb.c
>>> @@ -559,7 +559,7 @@ static struct fb_ops pxa168fb_ops = {
>>> ? ? ? .fb_imageblit ? = cfb_imageblit,
>>> ?};
>>>
>>> -static int __init pxa168fb_init_mode(struct fb_info *info,
>>> +static int pxa168fb_init_mode(struct fb_info *info,
>>> ? ? ? ? ? ? ? ? ? ? ? ? ? ? struct pxa168fb_mach_info *mi)
>>
>> Why do you remove __init from it ?
>>> ?{
>>> ? ? ? struct pxa168fb_info *fbi = info->par;
>>> @@ -599,7 +599,7 @@ static int __init pxa168fb_init_mode(struct fb_info
>>> *info, return ret;
>>> ?}
>>>
>>> -static int __init pxa168fb_probe(struct platform_device *pdev)
>>> +static int pxa168fb_probe(struct platform_device *pdev)
>>
>> Why do you remove __init from it ? (DTTO)
>>> ?{
>>> ? ? ? struct pxa168fb_mach_info *mi;
>>> ? ? ? struct fb_info *info = 0;
>>
>> Cheers
>>
>
> Hi Marek,
>
> 1) I removed the __init because it was causing a section mismatch
> warning wth this kernel. Since pxa168fb_probe() is calling
> pxa168fb_init_mode(), I cannot declare pxa168fb_init_mode() as an
> __init function. If pxa168fb_probe gets called after the __init
> section is wiped then it will attempt to run the deleted
> pxa168fb_init_mode() code.
>
> WARNING: vmlinux.o(.data+0x17984): Section mismatch in reference from
> the variable pxa168fb_driver to the function
> .init.text:pxa168fb_probe()
> The variable pxa168fb_driver references
> the function __init pxa168fb_probe()
> If the reference is valid then annotate the
> variable with __init* or __refdata (see linux/init.h) or name the variable:
> *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
>
>
> 2) What is the logic behind the delineation between patch files? I
> cannot build patch #1 without patch #2 based on how you defined the
> split. I need all of it in order to function.
>
Patch #2 should be the first one since it's related to framebuffer
driver. The next one should be platform file.

2010-08-26 04:03:08

by Marek Vasut

[permalink] [raw]
Subject: Re: [PATCH v2 1/1] pxa168: added initial support for TPO TD043MTEA1 LCD display on Aspenite

Dne ?t 26. srpna 2010 05:44:48 Mark F. Brown napsal(a):
> On Wed, Aug 25, 2010 at 10:26 PM, Marek Vasut <[email protected]> wrote:
> > Dne ?t 26. srpna 2010 04:04:52 Mark F. Brown napsal(a):
> >> Signed-off-by: Mark F. Brown <[email protected]>
> >> ---
> >> arch/arm/mach-mmp/aspenite.c | 60
> >> +++++++++++++++++++++++++++++++ arch/arm/mach-mmp/include/mach/pxa168.h
> >> | 8 ++++
> >> arch/arm/mach-mmp/pxa168.c | 4 ++
> >> drivers/video/pxa168fb.c | 4 +-
> >> 4 files changed, 74 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c
> >> index 0629394..9e1bd6b 100644
> >> --- a/arch/arm/mach-mmp/aspenite.c
> >> +++ b/arch/arm/mach-mmp/aspenite.c
> >> @@ -23,6 +23,7 @@
> >> #include <mach/mfp-pxa168.h>
> >> #include <mach/pxa168.h>
> >> #include <mach/gpio.h>
> >> +#include <video/pxa168fb.h>
> >>
> >> #include "common.h"
> >>
> >> @@ -66,6 +67,36 @@ static unsigned long common_pin_config[] __initdata =
> >> { GPIO115_I2S_BCLK,
> >> GPIO116_I2S_RXD,
> >> GPIO117_I2S_TXD,
> >> +
> >> + /* LCD */
> >> + GPIO56_LCD_FCLK_RD,
> >> + GPIO57_LCD_LCLK_A0,
> >> + GPIO58_LCD_PCLK_WR,
> >> + GPIO59_LCD_DENA_BIAS,
> >> + GPIO60_LCD_DD0,
> >> + GPIO61_LCD_DD1,
> >> + GPIO62_LCD_DD2,
> >> + GPIO63_LCD_DD3,
> >> + GPIO64_LCD_DD4,
> >> + GPIO65_LCD_DD5,
> >> + GPIO66_LCD_DD6,
> >> + GPIO67_LCD_DD7,
> >> + GPIO68_LCD_DD8,
> >> + GPIO69_LCD_DD9,
> >> + GPIO70_LCD_DD10,
> >> + GPIO71_LCD_DD11,
> >> + GPIO72_LCD_DD12,
> >> + GPIO73_LCD_DD13,
> >> + GPIO74_LCD_DD14,
> >> + GPIO75_LCD_DD15,
> >> + GPIO76_LCD_DD16,
> >> + GPIO77_LCD_DD17,
> >> + GPIO78_LCD_DD18,
> >> + GPIO79_LCD_DD19,
> >> + GPIO80_LCD_DD20,
> >> + GPIO81_LCD_DD21,
> >> + GPIO82_LCD_DD22,
> >> + GPIO83_LCD_DD23,
> >> };
> >>
> >> static struct smc91x_platdata smc91x_info = {
> >> @@ -134,6 +165,34 @@ static struct i2c_board_info aspenite_i2c_info[]
> >> __initdata = { { I2C_BOARD_INFO("wm8753", 0x1b), },
> >> };
> >>
> >> +static struct fb_videomode video_modes[] = {
> >> + [0] = {
> >> + .pixclock = 30120,
> >> + .refresh = 60,
> >> + .xres = 800,
> >> + .yres = 480,
> >> + .hsync_len = 1,
> >> + .left_margin = 215,
> >> + .right_margin = 40,
> >> + .vsync_len = 1,
> >> + .upper_margin = 34,
> >> + .lower_margin = 10,
> >> + .sync = FB_SYNC_VERT_HIGH_ACT |
> >> FB_SYNC_HOR_HIGH_ACT, + },
> >> +};
> >> +
> >> +struct pxa168fb_mach_info aspenite_lcd_info = {
> >> + .id = "Graphic Frame",
> >> + .modes = video_modes,
> >> + .num_modes = ARRAY_SIZE(video_modes),
> >> + .pix_fmt = PIX_FMT_RGB565,
> >> + .io_pin_allocation_mode = PIN_MODE_DUMB_24,
> >> + .dumb_mode = DUMB_MODE_RGB888,
> >> + .active = 1,
> >> + .panel_rbswap = 0,
> >> + .invert_pixclock = 0,
> >> +};
> >> +
> >> static void __init common_init(void)
> >> {
> >> mfp_config(ARRAY_AND_SIZE(common_pin_config));
> >> @@ -143,6 +202,7 @@ static void __init common_init(void)
> >> pxa168_add_twsi(1, NULL, ARRAY_AND_SIZE(aspenite_i2c_info));
> >> pxa168_add_ssp(1);
> >> pxa168_add_nand(&aspenite_nand_info);
> >> + pxa168_add_fb(&aspenite_lcd_info);
> >>
> >> /* off-chip devices */
> >> platform_device_register(&smc91x_device);
> >
> > ----------------------------------------------
> > ^--- one patch above
> > SNIP, please split into two patches
> > v--- another patch below
> > ----------------------------------------------
> >
> >> diff --git a/arch/arm/mach-mmp/include/mach/pxa168.h
> >> b/arch/arm/mach-mmp/include/mach/pxa168.h index 27e1bc7..220738f 100644
> >> --- a/arch/arm/mach-mmp/include/mach/pxa168.h
> >> +++ b/arch/arm/mach-mmp/include/mach/pxa168.h
> >> @@ -10,6 +10,7 @@ extern void __init pxa168_init_irq(void);
> >> #include <mach/devices.h>
> >> #include <plat/i2c.h>
> >> #include <plat/pxa3xx_nand.h>
> >> +#include <video/pxa168fb.h>
> >>
> >> extern struct pxa_device_desc pxa168_device_uart1;
> >> extern struct pxa_device_desc pxa168_device_uart2;
> >> @@ -25,6 +26,7 @@ extern struct pxa_device_desc pxa168_device_ssp3;
> >> extern struct pxa_device_desc pxa168_device_ssp4;
> >> extern struct pxa_device_desc pxa168_device_ssp5;
> >> extern struct pxa_device_desc pxa168_device_nand;
> >> +extern struct pxa_device_desc pxa168_device_fb;
> >>
> >> static inline int pxa168_add_uart(int id)
> >> {
> >> @@ -97,4 +99,10 @@ static inline int pxa168_add_nand(struct
> >> pxa3xx_nand_platform_data *info) {
> >> return pxa_register_device(&pxa168_device_nand, info,
> >> sizeof(*info)); }
> >> +
> >> +static inline int pxa168_add_fb(struct pxa168fb_mach_info *mi)
> >> +{
> >> + return pxa_register_device(&pxa168_device_fb, mi, sizeof(*mi));
> >> +}
> >> +
> >> #endif /* __ASM_MACH_PXA168_H */
> >> diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
> >> index 652ae66..886eadb 100644
> >> --- a/arch/arm/mach-mmp/pxa168.c
> >> +++ b/arch/arm/mach-mmp/pxa168.c
> >> @@ -25,6 +25,7 @@
> >> #include <mach/dma.h>
> >> #include <mach/devices.h>
> >> #include <mach/mfp.h>
> >> +#include <video/pxa168fb.h>
> >>
> >> #include "common.h"
> >> #include "clock.h"
> >> @@ -79,6 +80,7 @@ static APBC_CLK(ssp4, PXA168_SSP4, 4, 0);
> >> static APBC_CLK(ssp5, PXA168_SSP5, 4, 0);
> >>
> >> static APMU_CLK(nand, NAND, 0x01db, 208000000);
> >> +static APMU_CLK(lcd, LCD, 0x7f, 312000000);
> >>
> >> /* device and clock bindings */
> >> static struct clk_lookup pxa168_clkregs[] = {
> >> @@ -96,6 +98,7 @@ static struct clk_lookup pxa168_clkregs[] = {
> >> INIT_CLKREG(&clk_ssp4, "pxa168-ssp.3", NULL),
> >> INIT_CLKREG(&clk_ssp5, "pxa168-ssp.4", NULL),
> >> INIT_CLKREG(&clk_nand, "pxa3xx-nand", NULL),
> >> + INIT_CLKREG(&clk_lcd, "pxa168-fb", NULL),
> >> };
> >>
> >> static int __init pxa168_init(void)
> >> @@ -147,3 +150,4 @@ PXA168_DEVICE(ssp2, "pxa168-ssp", 1, SSP2,
> >> 0xd401c000, 0x40, 54, 55); PXA168_DEVICE(ssp3, "pxa168-ssp", 2, SSP3,
> >> 0xd401f000, 0x40, 56, 57); PXA168_DEVICE(ssp4, "pxa168-ssp", 3, SSP4,
> >> 0xd4020000, 0x40, 58, 59); PXA168_DEVICE(ssp5, "pxa168-ssp", 4, SSP5,
> >> 0xd4021000, 0x40, 60, 61); +PXA168_DEVICE(fb, "pxa168-fb", -1, LCD,
> >> 0xd420b000, 0x1c8);
> >> diff --git a/drivers/video/pxa168fb.c b/drivers/video/pxa168fb.c
> >> index c91a7f7..d3e597e 100644
> >> --- a/drivers/video/pxa168fb.c
> >> +++ b/drivers/video/pxa168fb.c
> >> @@ -559,7 +559,7 @@ static struct fb_ops pxa168fb_ops = {
> >> .fb_imageblit = cfb_imageblit,
> >> };
> >>
> >> -static int __init pxa168fb_init_mode(struct fb_info *info,
> >> +static int pxa168fb_init_mode(struct fb_info *info,
> >> struct pxa168fb_mach_info *mi)
> >
> > Why do you remove __init from it ?
> >
> >> {
> >> struct pxa168fb_info *fbi = info->par;
> >> @@ -599,7 +599,7 @@ static int __init pxa168fb_init_mode(struct fb_info
> >> *info, return ret;
> >> }
> >>
> >> -static int __init pxa168fb_probe(struct platform_device *pdev)
> >> +static int pxa168fb_probe(struct platform_device *pdev)
> >
> > Why do you remove __init from it ? (DTTO)
> >
> >> {
> >> struct pxa168fb_mach_info *mi;
> >> struct fb_info *info = 0;
> >
> > Cheers
>
> Hi Marek,
>
Hi,

Yep, always keep CC :-)

> 1) I removed the __init because it was causing a section mismatch
> warning wth this kernel. Since pxa168fb_probe() is calling
> pxa168fb_init_mode(), I cannot declare pxa168fb_init_mode() as an
> __init function. If pxa168fb_probe gets called after the __init
> section is wiped then it will attempt to run the deleted
> pxa168fb_init_mode() code.
>
> WARNING: vmlinux.o(.data+0x17984): Section mismatch in reference from
> the variable pxa168fb_driver to the function
> .init.text:pxa168fb_probe()
> The variable pxa168fb_driver references
> the function __init pxa168fb_probe()
> If the reference is valid then annotate the
> variable with __init* or __refdata (see linux/init.h) or name the variable:
> *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
>

Thanks for reporting this, please see my patch.
>
> 2) What is the logic behind the delineation between patch files? I
> cannot build patch #1 without patch #2 based on how you defined the
> split. I need all of it in order to function.

Create small patches that do not break stuff and are easy to review. By adding
small touches, you actually create a nice whole picture in the end :)

What I'd like to see is you to keep aspenite.c additions separate from cpu-wide
additions etc. This eventually also simplifies bisection if something goes
wrong.

Cheers
>
> -- Mark

2010-08-26 04:04:37

by Mark F. Brown

[permalink] [raw]
Subject: Re: [PATCH v2 1/1] pxa168: added initial support for TPO TD043MTEA1 LCD display on Aspenite

Makes sense!

Will do!

-- Mark

2010/8/26 Marek Vasut <[email protected]>:
> Dne ?t 26. srpna 2010 05:44:48 Mark F. Brown napsal(a):
>> On Wed, Aug 25, 2010 at 10:26 PM, Marek Vasut <[email protected]> wrote:
>> > Dne ?t 26. srpna 2010 04:04:52 Mark F. Brown napsal(a):
>> >> Signed-off-by: Mark F. Brown <[email protected]>
>> >> ---
>> >> ?arch/arm/mach-mmp/aspenite.c ? ? ? ? ? ?| ? 60
>> >> +++++++++++++++++++++++++++++++ arch/arm/mach-mmp/include/mach/pxa168.h
>> >> | 8 ++++
>> >> ?arch/arm/mach-mmp/pxa168.c ? ? ? ? ? ? ?| ? ?4 ++
>> >> ?drivers/video/pxa168fb.c ? ? ? ? ? ? ? ?| ? ?4 +-
>> >> ?4 files changed, 74 insertions(+), 2 deletions(-)
>> >>
>> >> diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c
>> >> index 0629394..9e1bd6b 100644
>> >> --- a/arch/arm/mach-mmp/aspenite.c
>> >> +++ b/arch/arm/mach-mmp/aspenite.c
>> >> @@ -23,6 +23,7 @@
>> >> ?#include <mach/mfp-pxa168.h>
>> >> ?#include <mach/pxa168.h>
>> >> ?#include <mach/gpio.h>
>> >> +#include <video/pxa168fb.h>
>> >>
>> >> ?#include "common.h"
>> >>
>> >> @@ -66,6 +67,36 @@ static unsigned long common_pin_config[] __initdata =
>> >> { GPIO115_I2S_BCLK,
>> >> ? ? ? GPIO116_I2S_RXD,
>> >> ? ? ? GPIO117_I2S_TXD,
>> >> +
>> >> + ? ? /* LCD */
>> >> + ? ? GPIO56_LCD_FCLK_RD,
>> >> + ? ? GPIO57_LCD_LCLK_A0,
>> >> + ? ? GPIO58_LCD_PCLK_WR,
>> >> + ? ? GPIO59_LCD_DENA_BIAS,
>> >> + ? ? GPIO60_LCD_DD0,
>> >> + ? ? GPIO61_LCD_DD1,
>> >> + ? ? GPIO62_LCD_DD2,
>> >> + ? ? GPIO63_LCD_DD3,
>> >> + ? ? GPIO64_LCD_DD4,
>> >> + ? ? GPIO65_LCD_DD5,
>> >> + ? ? GPIO66_LCD_DD6,
>> >> + ? ? GPIO67_LCD_DD7,
>> >> + ? ? GPIO68_LCD_DD8,
>> >> + ? ? GPIO69_LCD_DD9,
>> >> + ? ? GPIO70_LCD_DD10,
>> >> + ? ? GPIO71_LCD_DD11,
>> >> + ? ? GPIO72_LCD_DD12,
>> >> + ? ? GPIO73_LCD_DD13,
>> >> + ? ? GPIO74_LCD_DD14,
>> >> + ? ? GPIO75_LCD_DD15,
>> >> + ? ? GPIO76_LCD_DD16,
>> >> + ? ? GPIO77_LCD_DD17,
>> >> + ? ? GPIO78_LCD_DD18,
>> >> + ? ? GPIO79_LCD_DD19,
>> >> + ? ? GPIO80_LCD_DD20,
>> >> + ? ? GPIO81_LCD_DD21,
>> >> + ? ? GPIO82_LCD_DD22,
>> >> + ? ? GPIO83_LCD_DD23,
>> >> ?};
>> >>
>> >> ?static struct smc91x_platdata smc91x_info = {
>> >> @@ -134,6 +165,34 @@ static struct i2c_board_info aspenite_i2c_info[]
>> >> __initdata = { { I2C_BOARD_INFO("wm8753", 0x1b), },
>> >> ?};
>> >>
>> >> +static struct fb_videomode video_modes[] = {
>> >> + ? ? [0] = {
>> >> + ? ? ? ? ? ? .pixclock ? ? ? = 30120,
>> >> + ? ? ? ? ? ? .refresh ? ? ? ?= 60,
>> >> + ? ? ? ? ? ? .xres ? ? ? ? ? = 800,
>> >> + ? ? ? ? ? ? .yres ? ? ? ? ? = 480,
>> >> + ? ? ? ? ? ? .hsync_len ? ? ?= 1,
>> >> + ? ? ? ? ? ? .left_margin ? ?= 215,
>> >> + ? ? ? ? ? ? .right_margin ? = 40,
>> >> + ? ? ? ? ? ? .vsync_len ? ? ?= 1,
>> >> + ? ? ? ? ? ? .upper_margin ? = 34,
>> >> + ? ? ? ? ? ? .lower_margin ? = 10,
>> >> + ? ? ? ? ? ? .sync ? ? ? ? ? = FB_SYNC_VERT_HIGH_ACT |
>> >> FB_SYNC_HOR_HIGH_ACT, + ? ? },
>> >> +};
>> >> +
>> >> +struct pxa168fb_mach_info aspenite_lcd_info = {
>> >> + ? ? .id ? ? ? ? ? ? ? ? ? ? = "Graphic Frame",
>> >> + ? ? .modes ? ? ? ? ? ? ? ? ?= video_modes,
>> >> + ? ? .num_modes ? ? ? ? ? ? ?= ARRAY_SIZE(video_modes),
>> >> + ? ? .pix_fmt ? ? ? ? ? ? ? ?= PIX_FMT_RGB565,
>> >> + ? ? .io_pin_allocation_mode = PIN_MODE_DUMB_24,
>> >> + ? ? .dumb_mode ? ? ? ? ? ? ?= DUMB_MODE_RGB888,
>> >> + ? ? .active ? ? ? ? ? ? ? ? = 1,
>> >> + ? ? .panel_rbswap ? ? ? ? ? = 0,
>> >> + ? ? .invert_pixclock ? ? ? ?= 0,
>> >> +};
>> >> +
>> >> ?static void __init common_init(void)
>> >> ?{
>> >> ? ? ? mfp_config(ARRAY_AND_SIZE(common_pin_config));
>> >> @@ -143,6 +202,7 @@ static void __init common_init(void)
>> >> ? ? ? pxa168_add_twsi(1, NULL, ARRAY_AND_SIZE(aspenite_i2c_info));
>> >> ? ? ? pxa168_add_ssp(1);
>> >> ? ? ? pxa168_add_nand(&aspenite_nand_info);
>> >> + ? ? pxa168_add_fb(&aspenite_lcd_info);
>> >>
>> >> ? ? ? /* off-chip devices */
>> >> ? ? ? platform_device_register(&smc91x_device);
>> >
>> > ----------------------------------------------
>> > ^--- one patch above
>> > SNIP, please split into two patches
>> > v--- another patch below
>> > ----------------------------------------------
>> >
>> >> diff --git a/arch/arm/mach-mmp/include/mach/pxa168.h
>> >> b/arch/arm/mach-mmp/include/mach/pxa168.h index 27e1bc7..220738f 100644
>> >> --- a/arch/arm/mach-mmp/include/mach/pxa168.h
>> >> +++ b/arch/arm/mach-mmp/include/mach/pxa168.h
>> >> @@ -10,6 +10,7 @@ extern void __init pxa168_init_irq(void);
>> >> ?#include <mach/devices.h>
>> >> ?#include <plat/i2c.h>
>> >> ?#include <plat/pxa3xx_nand.h>
>> >> +#include <video/pxa168fb.h>
>> >>
>> >> ?extern struct pxa_device_desc pxa168_device_uart1;
>> >> ?extern struct pxa_device_desc pxa168_device_uart2;
>> >> @@ -25,6 +26,7 @@ extern struct pxa_device_desc pxa168_device_ssp3;
>> >> ?extern struct pxa_device_desc pxa168_device_ssp4;
>> >> ?extern struct pxa_device_desc pxa168_device_ssp5;
>> >> ?extern struct pxa_device_desc pxa168_device_nand;
>> >> +extern struct pxa_device_desc pxa168_device_fb;
>> >>
>> >> ?static inline int pxa168_add_uart(int id)
>> >> ?{
>> >> @@ -97,4 +99,10 @@ static inline int pxa168_add_nand(struct
>> >> pxa3xx_nand_platform_data *info) {
>> >> ? ? ? return pxa_register_device(&pxa168_device_nand, info,
>> >> sizeof(*info)); }
>> >> +
>> >> +static inline int pxa168_add_fb(struct pxa168fb_mach_info *mi)
>> >> +{
>> >> + ? ? return pxa_register_device(&pxa168_device_fb, mi, sizeof(*mi));
>> >> +}
>> >> +
>> >> ?#endif /* __ASM_MACH_PXA168_H */
>> >> diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c
>> >> index 652ae66..886eadb 100644
>> >> --- a/arch/arm/mach-mmp/pxa168.c
>> >> +++ b/arch/arm/mach-mmp/pxa168.c
>> >> @@ -25,6 +25,7 @@
>> >> ?#include <mach/dma.h>
>> >> ?#include <mach/devices.h>
>> >> ?#include <mach/mfp.h>
>> >> +#include <video/pxa168fb.h>
>> >>
>> >> ?#include "common.h"
>> >> ?#include "clock.h"
>> >> @@ -79,6 +80,7 @@ static APBC_CLK(ssp4, PXA168_SSP4, 4, 0);
>> >> ?static APBC_CLK(ssp5, PXA168_SSP5, 4, 0);
>> >>
>> >> ?static APMU_CLK(nand, NAND, 0x01db, 208000000);
>> >> +static APMU_CLK(lcd, LCD, 0x7f, 312000000);
>> >>
>> >> ?/* device and clock bindings */
>> >> ?static struct clk_lookup pxa168_clkregs[] = {
>> >> @@ -96,6 +98,7 @@ static struct clk_lookup pxa168_clkregs[] = {
>> >> ? ? ? INIT_CLKREG(&clk_ssp4, "pxa168-ssp.3", NULL),
>> >> ? ? ? INIT_CLKREG(&clk_ssp5, "pxa168-ssp.4", NULL),
>> >> ? ? ? INIT_CLKREG(&clk_nand, "pxa3xx-nand", NULL),
>> >> + ? ? INIT_CLKREG(&clk_lcd, "pxa168-fb", NULL),
>> >> ?};
>> >>
>> >> ?static int __init pxa168_init(void)
>> >> @@ -147,3 +150,4 @@ PXA168_DEVICE(ssp2, "pxa168-ssp", 1, SSP2,
>> >> 0xd401c000, 0x40, 54, 55); PXA168_DEVICE(ssp3, "pxa168-ssp", 2, SSP3,
>> >> 0xd401f000, 0x40, 56, 57); PXA168_DEVICE(ssp4, "pxa168-ssp", 3, SSP4,
>> >> 0xd4020000, 0x40, 58, 59); PXA168_DEVICE(ssp5, "pxa168-ssp", 4, SSP5,
>> >> 0xd4021000, 0x40, 60, 61); +PXA168_DEVICE(fb, "pxa168-fb", -1, LCD,
>> >> 0xd420b000, 0x1c8);
>> >> diff --git a/drivers/video/pxa168fb.c b/drivers/video/pxa168fb.c
>> >> index c91a7f7..d3e597e 100644
>> >> --- a/drivers/video/pxa168fb.c
>> >> +++ b/drivers/video/pxa168fb.c
>> >> @@ -559,7 +559,7 @@ static struct fb_ops pxa168fb_ops = {
>> >> ? ? ? .fb_imageblit ? = cfb_imageblit,
>> >> ?};
>> >>
>> >> -static int __init pxa168fb_init_mode(struct fb_info *info,
>> >> +static int pxa168fb_init_mode(struct fb_info *info,
>> >> ? ? ? ? ? ? ? ? ? ? ? ? ? ? struct pxa168fb_mach_info *mi)
>> >
>> > Why do you remove __init from it ?
>> >
>> >> ?{
>> >> ? ? ? struct pxa168fb_info *fbi = info->par;
>> >> @@ -599,7 +599,7 @@ static int __init pxa168fb_init_mode(struct fb_info
>> >> *info, return ret;
>> >> ?}
>> >>
>> >> -static int __init pxa168fb_probe(struct platform_device *pdev)
>> >> +static int pxa168fb_probe(struct platform_device *pdev)
>> >
>> > Why do you remove __init from it ? (DTTO)
>> >
>> >> ?{
>> >> ? ? ? struct pxa168fb_mach_info *mi;
>> >> ? ? ? struct fb_info *info = 0;
>> >
>> > Cheers
>>
>> Hi Marek,
>>
> Hi,
>
> Yep, always keep CC :-)
>
>> 1) I removed the __init because it was causing a section mismatch
>> warning wth this kernel. Since pxa168fb_probe() is calling
>> pxa168fb_init_mode(), I cannot declare pxa168fb_init_mode() as an
>> __init function. If pxa168fb_probe gets called after the __init
>> section is wiped then it will attempt to run the deleted
>> pxa168fb_init_mode() code.
>>
>> WARNING: vmlinux.o(.data+0x17984): Section mismatch in reference from
>> the variable pxa168fb_driver to the function
>> .init.text:pxa168fb_probe()
>> The variable pxa168fb_driver references
>> the function __init pxa168fb_probe()
>> If the reference is valid then annotate the
>> variable with __init* or __refdata (see linux/init.h) or name the variable:
>> *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
>>
>
> Thanks for reporting this, please see my patch.
>>
>> 2) What is the logic behind the delineation between patch files? I
>> cannot build patch #1 without patch #2 based on how you defined the
>> split. I need all of it in order to function.
>
> Create small patches that do not break stuff and are easy to review. By adding
> small touches, you actually create a nice whole picture in the end :)
>
> What I'd like to see is you to keep aspenite.c additions separate from cpu-wide
> additions etc. This eventually also simplifies bisection if something goes
> wrong.
>
> Cheers
>>
>> -- Mark
>