From: Keshava Munegowda <[email protected]>
The usbhs core driver does not enable/disable the intefrace and
fucntional clocks; These clocks are handled by hwmod and runtime pm,
hence insted of the clock enable/disable, the runtime pm APIS are
used. however,the port clocks and tll clocks are handled
by the usbhs core.
Signed-off-by: Keshava Munegowda <[email protected]>
---
drivers/mfd/omap-usb-host.c | 131 +++----------------------------------------
1 files changed, 9 insertions(+), 122 deletions(-)
diff --git a/drivers/mfd/omap-usb-host.c b/drivers/mfd/omap-usb-host.c
index 48ada2d..bd63429 100644
--- a/drivers/mfd/omap-usb-host.c
+++ b/drivers/mfd/omap-usb-host.c
@@ -26,6 +26,7 @@
#include <linux/spinlock.h>
#include <linux/gpio.h>
#include <plat/usb.h>
+#include <linux/pm_runtime.h>
#define USBHS_DRIVER_NAME "usbhs_omap"
#define OMAP_EHCI_DEVICE "ehci-omap"
@@ -146,9 +147,6 @@
struct usbhs_hcd_omap {
- struct clk *usbhost_ick;
- struct clk *usbhost_hs_fck;
- struct clk *usbhost_fs_fck;
struct clk *xclk60mhsp1_ck;
struct clk *xclk60mhsp2_ck;
struct clk *utmi_p1_fck;
@@ -158,8 +156,6 @@ struct usbhs_hcd_omap {
struct clk *usbhost_p2_fck;
struct clk *usbtll_p2_fck;
struct clk *init_60m_fclk;
- struct clk *usbtll_fck;
- struct clk *usbtll_ick;
void __iomem *uhh_base;
void __iomem *tll_base;
@@ -351,46 +347,13 @@ static int __devinit usbhs_omap_probe(struct platform_device *pdev)
omap->platdata.ehci_data = pdata->ehci_data;
omap->platdata.ohci_data = pdata->ohci_data;
- omap->usbhost_ick = clk_get(dev, "usbhost_ick");
- if (IS_ERR(omap->usbhost_ick)) {
- ret = PTR_ERR(omap->usbhost_ick);
- dev_err(dev, "usbhost_ick failed error:%d\n", ret);
- goto err_end;
- }
-
- omap->usbhost_hs_fck = clk_get(dev, "hs_fck");
- if (IS_ERR(omap->usbhost_hs_fck)) {
- ret = PTR_ERR(omap->usbhost_hs_fck);
- dev_err(dev, "usbhost_hs_fck failed error:%d\n", ret);
- goto err_usbhost_ick;
- }
-
- omap->usbhost_fs_fck = clk_get(dev, "fs_fck");
- if (IS_ERR(omap->usbhost_fs_fck)) {
- ret = PTR_ERR(omap->usbhost_fs_fck);
- dev_err(dev, "usbhost_fs_fck failed error:%d\n", ret);
- goto err_usbhost_hs_fck;
- }
-
- omap->usbtll_fck = clk_get(dev, "usbtll_fck");
- if (IS_ERR(omap->usbtll_fck)) {
- ret = PTR_ERR(omap->usbtll_fck);
- dev_err(dev, "usbtll_fck failed error:%d\n", ret);
- goto err_usbhost_fs_fck;
- }
-
- omap->usbtll_ick = clk_get(dev, "usbtll_ick");
- if (IS_ERR(omap->usbtll_ick)) {
- ret = PTR_ERR(omap->usbtll_ick);
- dev_err(dev, "usbtll_ick failed error:%d\n", ret);
- goto err_usbtll_fck;
- }
+ pm_runtime_enable(&pdev->dev);
omap->utmi_p1_fck = clk_get(dev, "utmi_p1_gfclk");
if (IS_ERR(omap->utmi_p1_fck)) {
ret = PTR_ERR(omap->utmi_p1_fck);
dev_err(dev, "utmi_p1_gfclk failed error:%d\n", ret);
- goto err_usbtll_ick;
+ goto err_end;
}
omap->xclk60mhsp1_ck = clk_get(dev, "xclk60mhsp1_ck");
@@ -520,22 +483,8 @@ err_xclk60mhsp1_ck:
err_utmi_p1_fck:
clk_put(omap->utmi_p1_fck);
-err_usbtll_ick:
- clk_put(omap->usbtll_ick);
-
-err_usbtll_fck:
- clk_put(omap->usbtll_fck);
-
-err_usbhost_fs_fck:
- clk_put(omap->usbhost_fs_fck);
-
-err_usbhost_hs_fck:
- clk_put(omap->usbhost_hs_fck);
-
-err_usbhost_ick:
- clk_put(omap->usbhost_ick);
-
err_end:
+ pm_runtime_disable(&pdev->dev);
kfree(omap);
end_probe:
@@ -569,11 +518,7 @@ static int __devexit usbhs_omap_remove(struct platform_device *pdev)
clk_put(omap->utmi_p2_fck);
clk_put(omap->xclk60mhsp1_ck);
clk_put(omap->utmi_p1_fck);
- clk_put(omap->usbtll_ick);
- clk_put(omap->usbtll_fck);
- clk_put(omap->usbhost_fs_fck);
- clk_put(omap->usbhost_hs_fck);
- clk_put(omap->usbhost_ick);
+ pm_runtime_disable(&pdev->dev);
kfree(omap);
return 0;
@@ -693,7 +638,6 @@ static int usbhs_enable(struct device *dev)
struct usbhs_omap_platform_data *pdata = &omap->platdata;
unsigned long flags = 0;
int ret = 0;
- unsigned long timeout;
unsigned reg;
dev_dbg(dev, "starting TI HSUSB Controller\n");
@@ -706,11 +650,7 @@ static int usbhs_enable(struct device *dev)
if (omap->count > 0)
goto end_count;
- clk_enable(omap->usbhost_ick);
- clk_enable(omap->usbhost_hs_fck);
- clk_enable(omap->usbhost_fs_fck);
- clk_enable(omap->usbtll_fck);
- clk_enable(omap->usbtll_ick);
+ pm_runtime_get_sync(dev);
if (pdata->ehci_data->phy_reset) {
if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0])) {
@@ -734,50 +674,6 @@ static int usbhs_enable(struct device *dev)
omap->usbhs_rev = usbhs_read(omap->uhh_base, OMAP_UHH_REVISION);
dev_dbg(dev, "OMAP UHH_REVISION 0x%x\n", omap->usbhs_rev);
- /* perform TLL soft reset, and wait until reset is complete */
- usbhs_write(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
- OMAP_USBTLL_SYSCONFIG_SOFTRESET);
-
- /* Wait for TLL reset to complete */
- timeout = jiffies + msecs_to_jiffies(1000);
- while (!(usbhs_read(omap->tll_base, OMAP_USBTLL_SYSSTATUS)
- & OMAP_USBTLL_SYSSTATUS_RESETDONE)) {
- cpu_relax();
-
- if (time_after(jiffies, timeout)) {
- dev_dbg(dev, "operation timed out\n");
- ret = -EINVAL;
- goto err_tll;
- }
- }
-
- dev_dbg(dev, "TLL RESET DONE\n");
-
- /* (1<<3) = no idle mode only for initial debugging */
- usbhs_write(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
- OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
- OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
- OMAP_USBTLL_SYSCONFIG_AUTOIDLE);
-
- /* Put UHH in NoIdle/NoStandby mode */
- reg = usbhs_read(omap->uhh_base, OMAP_UHH_SYSCONFIG);
- if (is_omap_usbhs_rev1(omap)) {
- reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
- | OMAP_UHH_SYSCONFIG_SIDLEMODE
- | OMAP_UHH_SYSCONFIG_CACTIVITY
- | OMAP_UHH_SYSCONFIG_MIDLEMODE);
- reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
-
-
- } else if (is_omap_usbhs_rev2(omap)) {
- reg &= ~OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR;
- reg |= OMAP4_UHH_SYSCONFIG_NOIDLE;
- reg &= ~OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR;
- reg |= OMAP4_UHH_SYSCONFIG_NOSTDBY;
- }
-
- usbhs_write(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg);
-
reg = usbhs_read(omap->uhh_base, OMAP_UHH_HOSTCONFIG);
/* setup ULPI bypass and burst configurations */
reg |= (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN
@@ -917,6 +813,8 @@ end_count:
return 0;
err_tll:
+ pm_runtime_put_sync(dev);
+ spin_unlock_irqrestore(&omap->lock, flags);
if (pdata->ehci_data->phy_reset) {
if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[0]))
gpio_free(pdata->ehci_data->reset_gpio_port[0]);
@@ -924,13 +822,6 @@ err_tll:
if (gpio_is_valid(pdata->ehci_data->reset_gpio_port[1]))
gpio_free(pdata->ehci_data->reset_gpio_port[1]);
}
-
- clk_disable(omap->usbtll_ick);
- clk_disable(omap->usbtll_fck);
- clk_disable(omap->usbhost_fs_fck);
- clk_disable(omap->usbhost_hs_fck);
- clk_disable(omap->usbhost_ick);
- spin_unlock_irqrestore(&omap->lock, flags);
return ret;
}
@@ -1003,11 +894,7 @@ static void usbhs_disable(struct device *dev)
clk_disable(omap->utmi_p1_fck);
}
- clk_disable(omap->usbtll_ick);
- clk_disable(omap->usbtll_fck);
- clk_disable(omap->usbhost_fs_fck);
- clk_disable(omap->usbhost_hs_fck);
- clk_disable(omap->usbhost_ick);
+ pm_runtime_put_sync(dev);
/* The gpio_free migh sleep; so unlock the spinlock */
spin_unlock_irqrestore(&omap->lock, flags);
--
1.6.0.4
On Mon, May 16, 2011 at 03:08:52PM +0530, Keshava Munegowda wrote:
> From: Keshava Munegowda <[email protected]>
>
> The usbhs core driver does not enable/disable the intefrace and
> fucntional clocks; These clocks are handled by hwmod and runtime pm,
> hence insted of the clock enable/disable, the runtime pm APIS are
> used. however,the port clocks and tll clocks are handled
> by the usbhs core.
>
> Signed-off-by: Keshava Munegowda <[email protected]>
Samuel how do we solve this series ? I can take the arch/arm/*omap*/
patches through Tony's tree, can you take the drivers/mfd/* via you
tree ?
--
balbi
Hi Felipe,
On Wed, May 18, 2011 at 01:48:09PM +0300, Felipe Balbi wrote:
> On Mon, May 16, 2011 at 03:08:52PM +0530, Keshava Munegowda wrote:
> > From: Keshava Munegowda <[email protected]>
> >
> > The usbhs core driver does not enable/disable the intefrace and
> > fucntional clocks; These clocks are handled by hwmod and runtime pm,
> > hence insted of the clock enable/disable, the runtime pm APIS are
> > used. however,the port clocks and tll clocks are handled
> > by the usbhs core.
> >
> > Signed-off-by: Keshava Munegowda <[email protected]>
>
> Samuel how do we solve this series ? I can take the arch/arm/*omap*/
> patches through Tony's tree, can you take the drivers/mfd/* via you
> tree ?
I'm taking this one. Let's hope the conflicts are not too bad.
Cheers,
Samuel.
--
Intel Open Source Technology Centre
http://oss.intel.com/