2013-08-01 14:00:22

by Sourav Poddar

[permalink] [raw]
Subject: [PATCHv8 0/2] Add ti qspi controller

This patch series add support for ti qspi controller.
Adapted this series on top of Mark brown series[1]:

[1]: https://patchwork.kernel.org/patch/2834694/

Sourav Poddar (2):
drivers: spi: Add qspi flash controller
driver: spi: Add quad spi read support

Documentation/devicetree/bindings/spi/ti_qspi.txt | 22 +
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-ti-qspi.c | 600 +++++++++++++++++++++
4 files changed, 631 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/ti_qspi.txt
create mode 100644 drivers/spi/spi-ti-qspi.c


2013-08-01 14:00:37

by Sourav Poddar

[permalink] [raw]
Subject: [RFC/PATCH 2/2] driver: spi: Add quad spi read support

Since, qspi controller uses quad read.

Configuring the command register, if the transfer of data needs
dual or quad lines.

This patch has been done on top of the following patch[1], which is just the
basic idea of adding dual/quad support in spi framework.
$subject patch will undergo changes once the ongoing discussion in the
community is freezed.

This patch is posted to demonstrate how patch 1 of the series will support
quad read.

[1]: http://comments.gmane.org/gmane.linux.kernel.spi.devel/14047

Signed-off-by: Sourav Poddar <[email protected]>
---
drivers/spi/spi-ti-qspi.c | 22 ++++++++++++++++------
1 files changed, 16 insertions(+), 6 deletions(-)

diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
index 73a1675..fac1722 100644
--- a/drivers/spi/spi-ti-qspi.c
+++ b/drivers/spi/spi-ti-qspi.c
@@ -265,18 +265,30 @@ static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t)
static int qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t)
{
int wlen, count, ret;
+ unsigned cmd = qspi->cmd;

count = t->len;
wlen = t->bits_per_word;

+ switch (t->bitwidth) {
+ case SPI_BITWIDTH_QUAD:
+ cmd |= QSPI_RD_QUAD;
+ break;
+ case SPI_BITWIDTH_DUAL:
+ cmd |= QSPI_RD_DUAL;
+ break;
+ case SPI_BITWIDTH_SINGLE:
+ default:
+ cmd |= QSPI_RD_SNGL;
+ }
+
if (wlen == 8) {
u8 *rxbuf;
rxbuf = t->rx_buf;
do {
dev_dbg(qspi->dev, "rx cmd %08x dc %08x\n",
qspi->cmd | QSPI_RD_SNGL, qspi->dc);
- ti_qspi_write(qspi, qspi->cmd | QSPI_RD_SNGL,
- QSPI_SPI_CMD_REG);
+ ti_qspi_write(qspi, cmd, QSPI_SPI_CMD_REG);
ret = wait_for_completion_timeout(&qspi->transfer_complete,
QSPI_COMPLETION_TIMEOUT);
if (ret == 0) {
@@ -294,8 +306,7 @@ static int qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t)
do {
dev_dbg(qspi->dev, "rx cmd %08x dc %08x\n",
qspi->cmd | QSPI_RD_SNGL, qspi->dc);
- ti_qspi_write(qspi, qspi->cmd | QSPI_RD_SNGL,
- QSPI_SPI_CMD_REG);
+ ti_qspi_write(qspi, cmd, QSPI_SPI_CMD_REG);
ret = wait_for_completion_timeout(&qspi->transfer_complete,
QSPI_COMPLETION_TIMEOUT);
if (ret == 0) {
@@ -313,8 +324,7 @@ static int qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t)
do {
dev_dbg(qspi->dev, "rx cmd %08x dc %08x\n",
qspi->cmd | QSPI_RD_SNGL, qspi->dc);
- ti_qspi_write(qspi, qspi->cmd | QSPI_RD_SNGL,
- QSPI_SPI_CMD_REG);
+ ti_qspi_write(qspi, cmd, QSPI_SPI_CMD_REG);
ret = wait_for_completion_timeout(&qspi->transfer_complete,
QSPI_COMPLETION_TIMEOUT);
if (ret == 0) {
--
1.7.1

2013-08-01 14:00:51

by Sourav Poddar

[permalink] [raw]
Subject: [PATCHv8 1/2] drivers: spi: Add qspi flash controller

The patch add basic support for the quad spi controller.

QSPI is a kind of spi module that allows single,
dual and quad read access to external spi devices. The module
has a memory mapped interface which provide direct interface
for accessing data form external spi devices.

The patch will configure controller clocks, device control
register and for defining low level transfer apis which
will be used by the spi framework to transfer data to
the slave spi device(flash in this case).

Test details:
-------------
Tested this on dra7 board.
Test1: Ran mtd_stesstest for 40000 iterations.
- All iterations went through without failure.
Test2: Use mtd utilities:
- flash_erase to erase the flash device
- nanddump to read data back.
- nandwrite to write to the data flash.
diff between the write and read data shows zero.

Signed-off-by: Sourav Poddar <[email protected]>
---
I have kept few more than 80 characters warning for better
code readilbilty.
v7->v8:
- Get rid of write/read data for better handling of
different word length
- Lock the transfer list
- miscellaneous cleanup.
Documentation/devicetree/bindings/spi/ti_qspi.txt | 22 +
drivers/spi/Kconfig | 8 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-ti-qspi.c | 591 +++++++++++++++++++++
4 files changed, 622 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/ti_qspi.txt
create mode 100644 drivers/spi/spi-ti-qspi.c

diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt
new file mode 100644
index 0000000..398ef59
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt
@@ -0,0 +1,22 @@
+TI QSPI controller.
+
+Required properties:
+- compatible : should be "ti,dra7xxx-qspi".
+- reg: Should contain QSPI registers location and length.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+- ti,hwmods: Name of the hwmod associated to the QSPI
+
+Recommended properties:
+- spi-max-frequency: Definition as per
+ Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+qspi: qspi@4b300000 {
+ compatible = "ti,dra7xxx-qspi";
+ reg = <0x4b300000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ spi-max-frequency = <25000000>;
+ ti,hwmods = "qspi";
+};
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 92a9345..1c4e758 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -285,6 +285,14 @@ config SPI_OMAP24XX
SPI master controller for OMAP24XX and later Multichannel SPI
(McSPI) modules.

+config SPI_TI_QSPI
+ tristate "DRA7xxx QSPI controller support"
+ depends on ARCH_OMAP2PLUS || COMPILE_TEST
+ help
+ QSPI master controller for DRA7xxx used for flash devices.
+ This device supports single, dual and quad read support, while
+ it only supports single write mode.
+
config SPI_OMAP_100K
tristate "OMAP SPI 100K"
depends on ARCH_OMAP850 || ARCH_OMAP730
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 33f9c09..a174030 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_SPI_OCTEON) += spi-octeon.o
obj-$(CONFIG_SPI_OMAP_UWIRE) += spi-omap-uwire.o
obj-$(CONFIG_SPI_OMAP_100K) += spi-omap-100k.o
obj-$(CONFIG_SPI_OMAP24XX) += spi-omap2-mcspi.o
+obj-$(CONFIG_SPI_TI_QSPI) += spi-ti-qspi.o
obj-$(CONFIG_SPI_ORION) += spi-orion.o
obj-$(CONFIG_SPI_PL022) += spi-pl022.o
obj-$(CONFIG_SPI_PPC4xx) += spi-ppc4xx.o
diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
new file mode 100644
index 0000000..1d5767d
--- /dev/null
+++ b/drivers/spi/spi-ti-qspi.c
@@ -0,0 +1,591 @@
+/*
+ * TI QSPI driver
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * Author: Sourav Poddar <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GPLv2.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/omap-dma.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/consumer.h>
+
+#include <linux/spi/spi.h>
+
+struct ti_qspi_regs {
+ u32 clkctrl;
+};
+
+struct ti_qspi {
+ struct completion transfer_complete;
+
+ /* IRQ synchronization */
+ spinlock_t lock;
+
+ /* list synchronization */
+ struct mutex list_lock;
+
+ struct spi_master *master;
+ void __iomem *base;
+ struct clk *fclk;
+ struct device *dev;
+
+ struct ti_qspi_regs ctx_reg;
+
+ u32 spi_max_frequency;
+ u32 cmd;
+ u32 dc;
+ u32 stat;
+};
+
+#define QSPI_PID (0x0)
+#define QSPI_SYSCONFIG (0x10)
+#define QSPI_INTR_STATUS_RAW_SET (0x20)
+#define QSPI_INTR_STATUS_ENABLED_CLEAR (0x24)
+#define QSPI_INTR_ENABLE_SET_REG (0x28)
+#define QSPI_INTR_ENABLE_CLEAR_REG (0x2c)
+#define QSPI_SPI_CLOCK_CNTRL_REG (0x40)
+#define QSPI_SPI_DC_REG (0x44)
+#define QSPI_SPI_CMD_REG (0x48)
+#define QSPI_SPI_STATUS_REG (0x4c)
+#define QSPI_SPI_DATA_REG (0x50)
+#define QSPI_SPI_SETUP0_REG (0x54)
+#define QSPI_SPI_SWITCH_REG (0x64)
+#define QSPI_SPI_SETUP1_REG (0x58)
+#define QSPI_SPI_SETUP2_REG (0x5c)
+#define QSPI_SPI_SETUP3_REG (0x60)
+#define QSPI_SPI_DATA_REG_1 (0x68)
+#define QSPI_SPI_DATA_REG_2 (0x6c)
+#define QSPI_SPI_DATA_REG_3 (0x70)
+
+#define QSPI_COMPLETION_TIMEOUT msecs_to_jiffies(2000)
+
+#define QSPI_FCLK 192000000
+
+/* Clock Control */
+#define QSPI_CLK_EN (1 << 31)
+#define QSPI_CLK_DIV_MAX 0xffff
+
+/* Command */
+#define QSPI_EN_CS(n) (n << 28)
+#define QSPI_WLEN(n) ((n-1) << 19)
+#define QSPI_3_PIN (1 << 18)
+#define QSPI_RD_SNGL (1 << 16)
+#define QSPI_WR_SNGL (2 << 16)
+#define QSPI_RD_DUAL (3 << 16)
+#define QSPI_RD_QUAD (7 << 16)
+#define QSPI_INVAL (4 << 16)
+#define QSPI_WC_CMD_INT_EN (1 << 14)
+#define QSPI_FLEN(n) ((n-1) << 0)
+
+/* STATUS REGISTER */
+#define WC 0x02
+
+/* INTERRUPT REGISTER */
+#define QSPI_WC_INT_EN (1 << 1)
+#define QSPI_WC_INT_DISABLE (1 << 1)
+
+/* Device Control */
+#define QSPI_DD(m, n) (m << (3 + n * 8))
+#define QSPI_CKPHA(n) (1 << (2 + n * 8))
+#define QSPI_CSPOL(n) (1 << (1 + n * 8))
+#define QSPI_CKPOL(n) (1 << (n*8))
+
+#define QSPI_FRAME 4096
+
+#define QSPI_AUTOSUSPEND_TIMEOUT 2000
+
+static inline unsigned long ti_qspi_read(struct ti_qspi *qspi,
+ unsigned long reg)
+{
+ return readl(qspi->base + reg);
+}
+
+static inline void ti_qspi_write(struct ti_qspi *qspi,
+ unsigned long val, unsigned long reg)
+{
+ writel(val, qspi->base + reg);
+}
+
+static int ti_qspi_setup(struct spi_device *spi)
+{
+ struct ti_qspi *qspi = spi_master_get_devdata(spi->master);
+ struct ti_qspi_regs *ctx_reg = &qspi->ctx_reg;
+ int clk_div = 0, ret;
+ u32 clk_ctrl_reg, clk_rate, clk_mask;
+
+ if (spi->master->busy) {
+ dev_dbg(qspi->dev, "master busy doing other trasnfers\n");
+ return -EBUSY;
+ }
+
+ if (!qspi->spi_max_frequency) {
+ dev_err(qspi->dev, "spi max frequency not defined\n");
+ return -EINVAL;
+ }
+
+ clk_rate = clk_get_rate(qspi->fclk);
+
+ clk_div = DIV_ROUND_UP(clk_rate, qspi->spi_max_frequency) - 1;
+
+ if (clk_div < 0) {
+ dev_dbg(qspi->dev, "%s: clock divider < 0, using /1 divider\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ if (clk_div > QSPI_CLK_DIV_MAX) {
+ dev_dbg(qspi->dev, "%s: clock divider >%d , using /%d divider\n",
+ __func__, QSPI_CLK_DIV_MAX, QSPI_CLK_DIV_MAX + 1);
+ return -EINVAL;
+ }
+
+ dev_dbg(qspi->dev, "%s: hz: %d, clock divider %d\n", __func__,
+ qspi->spi_max_frequency, clk_div);
+
+ ret = pm_runtime_get_sync(qspi->dev);
+ if (ret) {
+ dev_err(qspi->dev, "pm_runtime_get_sync() failed\n");
+ return ret;
+ }
+
+ clk_ctrl_reg = ti_qspi_read(qspi, QSPI_SPI_CLOCK_CNTRL_REG);
+
+ clk_ctrl_reg &= ~QSPI_CLK_EN;
+
+ /* disable SCLK */
+ ti_qspi_write(qspi, clk_ctrl_reg, QSPI_SPI_CLOCK_CNTRL_REG);
+
+ /* enable SCLK */
+ clk_mask = QSPI_CLK_EN | clk_div;
+ ti_qspi_write(qspi, clk_mask, QSPI_SPI_CLOCK_CNTRL_REG);
+ ctx_reg->clkctrl = clk_mask;
+
+ pm_runtime_mark_last_busy(qspi->dev);
+ ret = pm_runtime_put_autosuspend(qspi->dev);
+ if (ret < 0) {
+ dev_err(qspi->dev, "pm_runtime_get_sync() failed\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static void ti_qspi_restore_ctx(struct ti_qspi *qspi)
+{
+ struct ti_qspi_regs *ctx_reg = &qspi->ctx_reg;
+
+ ti_qspi_write(qspi, ctx_reg->clkctrl, QSPI_SPI_CLOCK_CNTRL_REG);
+}
+
+static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t)
+{
+ int wlen, count, ret;
+
+ count = t->len;
+ wlen = t->bits_per_word;
+
+ if (wlen == 8) {
+ const u8 *txbuf;
+ txbuf = t->tx_buf;
+ do {
+ dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %02x\n",
+ qspi->cmd | QSPI_WR_SNGL, qspi->dc, *txbuf);
+ writeb(*txbuf++, qspi->base + QSPI_SPI_DATA_REG);
+ ti_qspi_write(qspi, qspi->cmd | QSPI_WR_SNGL,
+ QSPI_SPI_CMD_REG);
+ ret = wait_for_completion_timeout(&qspi->transfer_complete,
+ QSPI_COMPLETION_TIMEOUT);
+ if (ret == 0) {
+ dev_err(qspi->dev, "write timed out\n");
+ return -ETIMEDOUT;
+ }
+ count -= 1;
+ } while (count);
+ } else if (wlen == 16) {
+ const u16 *txbuf;
+ txbuf = t->tx_buf;
+ do {
+ dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %04x\n",
+ qspi->cmd | QSPI_WR_SNGL, qspi->dc, *txbuf);
+ writew(*txbuf++, qspi->base + QSPI_SPI_DATA_REG);
+ ti_qspi_write(qspi, qspi->cmd | QSPI_WR_SNGL,
+ QSPI_SPI_CMD_REG);
+ ret = wait_for_completion_timeout(&qspi->transfer_complete,
+ QSPI_COMPLETION_TIMEOUT);
+ if (ret == 0) {
+ dev_err(qspi->dev, "write timed out\n");
+ return -ETIMEDOUT;
+ }
+ count -= 2;
+ } while (count >= 2);
+ } else if (wlen == 32) {
+ const u32 *txbuf;
+ txbuf = t->tx_buf;
+ do {
+ dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %08x\n",
+ qspi->cmd | QSPI_WR_SNGL, qspi->dc, *txbuf);
+ writel(*txbuf++, qspi->base + QSPI_SPI_DATA_REG);
+ ti_qspi_write(qspi, qspi->cmd | QSPI_WR_SNGL,
+ QSPI_SPI_CMD_REG);
+ ret = wait_for_completion_timeout(&qspi->transfer_complete,
+ QSPI_COMPLETION_TIMEOUT);
+ if (ret == 0) {
+ dev_err(qspi->dev, "write timed out\n");
+ return -ETIMEDOUT;
+ }
+ count -= 2;
+ } while (count >= 4);
+ }
+
+ return 0;
+}
+
+static int qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t)
+{
+ int wlen, count, ret;
+
+ count = t->len;
+ wlen = t->bits_per_word;
+
+ if (wlen == 8) {
+ u8 *rxbuf;
+ rxbuf = t->rx_buf;
+ do {
+ dev_dbg(qspi->dev, "rx cmd %08x dc %08x\n",
+ qspi->cmd | QSPI_RD_SNGL, qspi->dc);
+ ti_qspi_write(qspi, qspi->cmd | QSPI_RD_SNGL,
+ QSPI_SPI_CMD_REG);
+ ret = wait_for_completion_timeout(&qspi->transfer_complete,
+ QSPI_COMPLETION_TIMEOUT);
+ if (ret == 0) {
+ dev_err(qspi->dev, "read timed out\n");
+ return -ETIMEDOUT;
+ }
+ *rxbuf++ = readb(qspi->base + QSPI_SPI_DATA_REG);
+ dev_vdbg(qspi->dev, "rx done, read %02x\n",
+ *(rxbuf - 1));
+ count -= 1;
+ } while (count);
+ } else if (wlen == 16) {
+ u16 *rxbuf;
+ rxbuf = t->rx_buf;
+ do {
+ dev_dbg(qspi->dev, "rx cmd %08x dc %08x\n",
+ qspi->cmd | QSPI_RD_SNGL, qspi->dc);
+ ti_qspi_write(qspi, qspi->cmd | QSPI_RD_SNGL,
+ QSPI_SPI_CMD_REG);
+ ret = wait_for_completion_timeout(&qspi->transfer_complete,
+ QSPI_COMPLETION_TIMEOUT);
+ if (ret == 0) {
+ dev_err(qspi->dev, "read timed out\n");
+ return -ETIMEDOUT;
+ }
+ *rxbuf++ = readw(qspi->base + QSPI_SPI_DATA_REG);
+ dev_vdbg(qspi->dev, "rx done, read %04x\n",
+ *(rxbuf - 2));
+ count -= 2;
+ } while (count >= 2);
+ } else if (wlen == 32) {
+ u32 *rxbuf;
+ rxbuf = t->rx_buf;
+ do {
+ dev_dbg(qspi->dev, "rx cmd %08x dc %08x\n",
+ qspi->cmd | QSPI_RD_SNGL, qspi->dc);
+ ti_qspi_write(qspi, qspi->cmd | QSPI_RD_SNGL,
+ QSPI_SPI_CMD_REG);
+ ret = wait_for_completion_timeout(&qspi->transfer_complete,
+ QSPI_COMPLETION_TIMEOUT);
+ if (ret == 0) {
+ dev_err(qspi->dev, "read timed out\n");
+ return -ETIMEDOUT;
+ }
+ *rxbuf++ = readl(qspi->base + QSPI_SPI_DATA_REG);
+ dev_vdbg(qspi->dev, "rx done, read %08x\n",
+ *(rxbuf - 4));
+ count -= 4;
+ } while (count >= 4);
+ }
+
+ return 0;
+}
+
+static int qspi_transfer_msg(struct ti_qspi *qspi, struct spi_transfer *t)
+{
+ int ret;
+
+ if (t->tx_buf) {
+ ret = qspi_write_msg(qspi, t);
+ if (ret) {
+ dev_dbg(qspi->dev, "Error while writing\n");
+ return -ETIMEDOUT;
+ }
+ }
+
+ if (t->rx_buf) {
+ ret = qspi_read_msg(qspi, t);
+ if (ret) {
+ dev_dbg(qspi->dev, "Error while writing\n");
+ return -ETIMEDOUT;
+ }
+ }
+
+ return 0;
+}
+
+static int ti_qspi_start_transfer_one(struct spi_master *master,
+ struct spi_message *m)
+{
+ struct ti_qspi *qspi = spi_master_get_devdata(master);
+ struct spi_device *spi = m->spi;
+ struct spi_transfer *t;
+ int status = 0, ret;
+ int frame_length;
+
+ /* setup device control reg */
+ qspi->dc = 0;
+
+ if (spi->mode & SPI_CPHA)
+ qspi->dc |= QSPI_CKPHA(spi->chip_select);
+ if (spi->mode & SPI_CPOL)
+ qspi->dc |= QSPI_CKPOL(spi->chip_select);
+ if (spi->mode & SPI_CS_HIGH)
+ qspi->dc |= QSPI_CSPOL(spi->chip_select);
+
+ frame_length = (m->frame_length << 3) / spi->bits_per_word;
+
+ frame_length = clamp(frame_length, 0, QSPI_FRAME);
+
+ /* setup command reg */
+ qspi->cmd = 0;
+ qspi->cmd |= QSPI_EN_CS(spi->chip_select);
+ qspi->cmd |= QSPI_FLEN(frame_length);
+ qspi->cmd |= QSPI_WC_CMD_INT_EN;
+
+ ti_qspi_write(qspi, QSPI_WC_INT_EN, QSPI_INTR_ENABLE_SET_REG);
+ ti_qspi_write(qspi, qspi->dc, QSPI_SPI_DC_REG);
+
+ mutex_lock(&qspi->list_lock);
+
+ list_for_each_entry(t, &m->transfers, transfer_list) {
+ qspi->cmd |= QSPI_WLEN(t->bits_per_word);
+
+ ret = qspi_transfer_msg(qspi, t);
+ if (ret) {
+ dev_dbg(qspi->dev, "transfer message failed\n");
+ return -EINVAL;
+ }
+
+ m->actual_length += t->len;
+ }
+
+ mutex_unlock(&qspi->list_lock);
+
+ m->status = status;
+ spi_finalize_current_message(master);
+
+ ti_qspi_write(qspi, qspi->cmd | QSPI_INVAL, QSPI_SPI_CMD_REG);
+
+ return status;
+}
+
+static irqreturn_t ti_qspi_isr(int irq, void *dev_id)
+{
+ struct ti_qspi *qspi = dev_id;
+ u16 int_stat;
+
+ irqreturn_t ret = IRQ_HANDLED;
+
+ spin_lock(&qspi->lock);
+
+ int_stat = ti_qspi_read(qspi, QSPI_INTR_STATUS_ENABLED_CLEAR);
+ qspi->stat = ti_qspi_read(qspi, QSPI_SPI_STATUS_REG);
+
+ if (!int_stat) {
+ dev_dbg(qspi->dev, "No IRQ triggered\n");
+ ret = IRQ_NONE;
+ goto out;
+ }
+
+ ret = IRQ_WAKE_THREAD;
+
+ ti_qspi_write(qspi, QSPI_WC_INT_DISABLE, QSPI_INTR_ENABLE_CLEAR_REG);
+ ti_qspi_write(qspi, QSPI_WC_INT_DISABLE,
+ QSPI_INTR_STATUS_ENABLED_CLEAR);
+
+out:
+ spin_unlock(&qspi->lock);
+
+ return ret;
+}
+
+static irqreturn_t ti_qspi_threaded_isr(int this_irq, void *dev_id)
+{
+ struct ti_qspi *qspi = dev_id;
+ unsigned long flags;
+
+ spin_lock_irqsave(&qspi->lock, flags);
+
+ if (qspi->stat & WC)
+ complete(&qspi->transfer_complete);
+
+ spin_unlock_irqrestore(&qspi->lock, flags);
+
+ ti_qspi_write(qspi, QSPI_WC_INT_EN, QSPI_INTR_ENABLE_SET_REG);
+
+ return IRQ_HANDLED;
+}
+
+static int ti_qspi_runtime_resume(struct device *dev)
+{
+ struct ti_qspi *qspi;
+ struct spi_master *master;
+
+ master = dev_get_drvdata(dev);
+ qspi = spi_master_get_devdata(master);
+ ti_qspi_restore_ctx(qspi);
+
+ return 0;
+}
+
+static const struct of_device_id ti_qspi_match[] = {
+ {.compatible = "ti,dra7xxx-qspi" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, dra7xxx_qspi_match);
+
+static int ti_qspi_probe(struct platform_device *pdev)
+{
+ struct ti_qspi *qspi;
+ struct spi_master *master;
+ struct resource *r;
+ struct device_node *np = pdev->dev.of_node;
+ u32 max_freq;
+ int ret = 0, num_cs, irq;
+
+ master = spi_alloc_master(&pdev->dev, sizeof(*qspi));
+ if (!master)
+ return -ENOMEM;
+
+ master->mode_bits = SPI_CPOL | SPI_CPHA;
+
+ master->bus_num = -1;
+ master->flags = SPI_MASTER_HALF_DUPLEX;
+ master->setup = ti_qspi_setup;
+ master->auto_runtime_pm = true;
+ master->transfer_one_message = ti_qspi_start_transfer_one;
+ master->dev.of_node = pdev->dev.of_node;
+ master->bits_per_word_mask = BIT(32 - 1) | BIT(16 - 1) | BIT(8 - 1);
+
+ if (!of_property_read_u32(np, "num-cs", &num_cs))
+ master->num_chipselect = num_cs;
+
+ platform_set_drvdata(pdev, master);
+
+ qspi = spi_master_get_devdata(master);
+ qspi->master = master;
+ qspi->dev = &pdev->dev;
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "no irq resource?\n");
+ return irq;
+ }
+
+ spin_lock_init(&qspi->lock);
+ mutex_init(&qspi->list_lock);
+
+ qspi->base = devm_ioremap_resource(&pdev->dev, r);
+ if (IS_ERR(qspi->base)) {
+ ret = PTR_ERR(qspi->base);
+ goto free_master;
+ }
+
+ ret = devm_request_threaded_irq(&pdev->dev, irq, ti_qspi_isr,
+ ti_qspi_threaded_isr, 0,
+ dev_name(&pdev->dev), qspi);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to register ISR for IRQ %d\n",
+ irq);
+ goto free_master;
+ }
+
+ qspi->fclk = devm_clk_get(&pdev->dev, "fck");
+ if (IS_ERR(qspi->fclk)) {
+ ret = PTR_ERR(qspi->fclk);
+ dev_err(&pdev->dev, "could not get clk: %d\n", ret);
+ }
+
+ init_completion(&qspi->transfer_complete);
+
+ pm_runtime_use_autosuspend(&pdev->dev);
+ pm_runtime_set_autosuspend_delay(&pdev->dev, QSPI_AUTOSUSPEND_TIMEOUT);
+ pm_runtime_enable(&pdev->dev);
+
+ if (!of_property_read_u32(np, "spi-max-frequency", &max_freq))
+ qspi->spi_max_frequency = max_freq;
+
+ ret = spi_register_master(master);
+ if (ret)
+ goto free_master;
+
+ return 0;
+
+free_master:
+ spi_master_put(master);
+ return ret;
+}
+
+static int ti_qspi_remove(struct platform_device *pdev)
+{
+ struct ti_qspi *qspi = platform_get_drvdata(pdev);
+
+ spi_unregister_master(qspi->master);
+
+ return 0;
+}
+
+static const struct dev_pm_ops ti_qspi_pm_ops = {
+ .runtime_resume = ti_qspi_runtime_resume,
+};
+
+static struct platform_driver ti_qspi_driver = {
+ .probe = ti_qspi_probe,
+ .remove = ti_qspi_remove,
+ .driver = {
+ .name = "ti,dra7xxx-qspi",
+ .owner = THIS_MODULE,
+ .pm = &ti_qspi_pm_ops,
+ .of_match_table = ti_qspi_match,
+ }
+};
+
+module_platform_driver(ti_qspi_driver);
+
+MODULE_AUTHOR("Sourav Poddar <[email protected]>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI QSPI controller driver");
--
1.7.1

2013-08-01 14:07:38

by Felipe Balbi

[permalink] [raw]
Subject: Re: [PATCHv8 1/2] drivers: spi: Add qspi flash controller

Hi,

On Thu, Aug 01, 2013 at 07:30:01PM +0530, Sourav Poddar wrote:
> +static int ti_qspi_setup(struct spi_device *spi)
> +{

[snip]

> + pm_runtime_mark_last_busy(qspi->dev);
> + ret = pm_runtime_put_autosuspend(qspi->dev);
> + if (ret < 0) {
> + dev_err(qspi->dev, "pm_runtime_get_sync() failed\n");

wrong error message.

> +static int qspi_transfer_msg(struct ti_qspi *qspi, struct spi_transfer *t)
> +{
> + int ret;
> +
> + if (t->tx_buf) {
> + ret = qspi_write_msg(qspi, t);
> + if (ret) {
> + dev_dbg(qspi->dev, "Error while writing\n");
> + return -ETIMEDOUT;

return ret;

> + }
> + }
> +
> + if (t->rx_buf) {
> + ret = qspi_read_msg(qspi, t);
> + if (ret) {
> + dev_dbg(qspi->dev, "Error while writing\n");
> + return -ETIMEDOUT;

return ret;

--
balbi


Attachments:
(No filename) (778.00 B)
signature.asc (836.00 B)
Digital signature
Download all attachments