v3:
Suggested by Kishon
Change binding doc name to hix5hd2-phy.txt
Add HAS_IOMEM depends, and change include file sequence
v2:
Suggested by Mark
Remove hisilicon,reg-init and init the register in phy-hix5hd2-sata.c
Change property name accordingly.
Jiancheng Xue (2):
Documentation: Document Hisilicon hix5hd2 sata PHY
phy: add hix5hd2-sata-phy driver
.../devicetree/bindings/phy/hix5hd2-phy.txt | 22 +++
drivers/phy/Kconfig | 8 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-hix5hd2-sata.c | 192 ++++++++++++++++++++
4 files changed, 223 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/hix5hd2-phy.txt
create mode 100644 drivers/phy/phy-hix5hd2-sata.c
--
1.7.9.5
From: Jiancheng Xue <[email protected]>
Add necessary binding documentation SATA PHY on Hisilicon hix5hd2 soc.
Signed-off-by: Jiancheng Xue <[email protected]>
Signed-off-by: Zhangfei Gao <[email protected]>
---
.../devicetree/bindings/phy/hix5hd2-phy.txt | 22 ++++++++++++++++++++
1 file changed, 22 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/hix5hd2-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt
new file mode 100644
index 0000000..296168b
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt
@@ -0,0 +1,22 @@
+Hisilicon hix5hd2 SATA PHY
+-----------------------
+
+Required properties:
+- compatible: should be "hisilicon,hix5hd2-sata-phy"
+- reg: offset and length of the PHY registers
+- #phy-cells: must be 0
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Optional Properties:
+- hisilicon,peripheral-syscon: phandle of syscon used to control peripheral.
+- hisilicon,power-reg: offset and bit number within peripheral-syscon,
+ register of controlling sata power supply.
+
+Example:
+ sata_phy: phy@f9900000 {
+ compatible = "hisilicon,hix5hd2-sata-phy";
+ reg = <0xf9900000 0x10000>;
+ #phy-cells = <0>;
+ hisilicon,peripheral-syscon = <&peripheral_ctrl>;
+ hisilicon,power-reg = <0x8 10>;
+ };
--
1.7.9.5
From: Jiancheng Xue <[email protected]>
Add hix5hd2-sata-phy driver on Hisilicon hix5hd2 soc.
Signed-off-by: Jiancheng Xue <[email protected]>
Signed-off-by: Zhangfei Gao <[email protected]>
---
drivers/phy/Kconfig | 8 ++
drivers/phy/Makefile | 1 +
drivers/phy/phy-hix5hd2-sata.c | 192 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 201 insertions(+)
create mode 100644 drivers/phy/phy-hix5hd2-sata.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 16a2f06..4726af5 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -109,6 +109,14 @@ config PHY_EXYNOS5250_SATA
SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds. It supports one SATA host
port to accept one SATA device.
+config PHY_HIX5HD2_SATA
+ tristate "HIX5HD2 SATA PHY Driver"
+ depends on ARCH_HIX5HD2 && OF && HAS_IOMEM
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ Support for SATA PHY on Hisilicon hix5hd2 Soc.
+
config PHY_SUN4I_USB
tristate "Allwinner sunxi SoC USB PHY driver"
depends on ARCH_SUNXI && HAS_IOMEM && OF
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index b4f1d57..54f04d0 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o
obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o
obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o
+obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-exynos-usb2.o
phy-exynos-usb2-y += phy-samsung-usb2.o
diff --git a/drivers/phy/phy-hix5hd2-sata.c b/drivers/phy/phy-hix5hd2-sata.c
new file mode 100644
index 0000000..d442834
--- /dev/null
+++ b/drivers/phy/phy-hix5hd2-sata.c
@@ -0,0 +1,192 @@
+/*
+ * Copyright (c) 2014 Linaro Ltd.
+ * Copyright (c) 2014 Hisilicon Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define SATA_PHY0_CTLL 0xa0
+#define MPLL_MULTIPLIER_SHIFT 1
+#define MPLL_MULTIPLIER_MASK 0xfe
+#define MPLL_MULTIPLIER_50M 0x3c
+#define MPLL_MULTIPLIER_100M 0x1e
+#define PHY_RESET BIT(0)
+#define REF_SSP_EN BIT(9)
+#define SSC_EN BIT(10)
+#define REF_USE_PAD BIT(23)
+
+#define SATA_PORT_PHYCTL 0x174
+#define SPEED_MODE_MASK 0x6f0000
+#define HALF_RATE_SHIFT 16
+#define PHY_CONFIG_SHIFT 18
+#define GEN2_EN_SHIFT 21
+#define SPEED_CTRL BIT(20)
+
+#define SATA_PORT_PHYCTL1 0x148
+#define AMPLITUDE_MASK 0x3ffffe
+#define AMPLITUDE_GEN3 0x68
+#define AMPLITUDE_GEN3_SHIFT 15
+#define AMPLITUDE_GEN2 0x56
+#define AMPLITUDE_GEN2_SHIFT 8
+#define AMPLITUDE_GEN1 0x56
+#define AMPLITUDE_GEN1_SHIFT 1
+
+#define SATA_PORT_PHYCTL2 0x14c
+#define PREEMPH_MASK 0x3ffff
+#define PREEMPH_GEN3 0x20
+#define PREEMPH_GEN3_SHIFT 12
+#define PREEMPH_GEN2 0x15
+#define PREEMPH_GEN2_SHIFT 6
+#define PREEMPH_GEN1 0x5
+#define PREEMPH_GEN1_SHIFT 0
+
+struct hix5hd2_priv {
+ void __iomem *base;
+ struct regmap *peri_ctrl;
+};
+
+enum phy_speed_mode {
+ SPEED_MODE_GEN1 = 0,
+ SPEED_MODE_GEN2 = 1,
+ SPEED_MODE_GEN3 = 2,
+};
+
+static int hix5hd2_sata_phy_init(struct phy *phy)
+{
+ struct hix5hd2_priv *priv = phy_get_drvdata(phy);
+ u32 val, data[2];
+ int ret;
+
+ if (priv->peri_ctrl) {
+ ret = of_property_read_u32_array(phy->dev.of_node,
+ "hisilicon,power-reg",
+ &data[0], 2);
+ if (ret) {
+ dev_err(&phy->dev, "Fail read hisilicon,power-reg\n");
+ return ret;
+ }
+
+ regmap_update_bits(priv->peri_ctrl, data[0],
+ BIT(data[1]), BIT(data[1]));
+ }
+
+ /* reset phy */
+ val = readl_relaxed(priv->base + SATA_PHY0_CTLL);
+ val &= ~(MPLL_MULTIPLIER_MASK | REF_USE_PAD);
+ val |= MPLL_MULTIPLIER_50M << MPLL_MULTIPLIER_SHIFT |
+ REF_SSP_EN | PHY_RESET;
+ writel_relaxed(val, priv->base + SATA_PHY0_CTLL);
+ msleep(20);
+ val &= ~PHY_RESET;
+ writel_relaxed(val, priv->base + SATA_PHY0_CTLL);
+
+ val = readl_relaxed(priv->base + SATA_PORT_PHYCTL1);
+ val &= ~AMPLITUDE_MASK;
+ val |= AMPLITUDE_GEN3 << AMPLITUDE_GEN3_SHIFT |
+ AMPLITUDE_GEN2 << AMPLITUDE_GEN2_SHIFT |
+ AMPLITUDE_GEN1 << AMPLITUDE_GEN1_SHIFT;
+ writel_relaxed(val, priv->base + SATA_PORT_PHYCTL1);
+
+ val = readl_relaxed(priv->base + SATA_PORT_PHYCTL2);
+ val &= ~PREEMPH_MASK;
+ val |= PREEMPH_GEN3 << PREEMPH_GEN3_SHIFT |
+ PREEMPH_GEN2 << PREEMPH_GEN2_SHIFT |
+ PREEMPH_GEN1 << PREEMPH_GEN1_SHIFT;
+ writel_relaxed(val, priv->base + SATA_PORT_PHYCTL2);
+
+ /* ensure PHYCTRL setting takes effect */
+ val = readl_relaxed(priv->base + SATA_PORT_PHYCTL);
+ val &= ~SPEED_MODE_MASK;
+ val |= SPEED_MODE_GEN1 << HALF_RATE_SHIFT |
+ SPEED_MODE_GEN1 << PHY_CONFIG_SHIFT |
+ SPEED_MODE_GEN1 << GEN2_EN_SHIFT | SPEED_CTRL;
+ writel_relaxed(val, priv->base + SATA_PORT_PHYCTL);
+
+ msleep(20);
+ val &= ~SPEED_MODE_MASK;
+ val |= SPEED_MODE_GEN3 << HALF_RATE_SHIFT |
+ SPEED_MODE_GEN3 << PHY_CONFIG_SHIFT |
+ SPEED_MODE_GEN3 << GEN2_EN_SHIFT | SPEED_CTRL;
+ writel_relaxed(val, priv->base + SATA_PORT_PHYCTL);
+
+ val &= ~(SPEED_MODE_MASK | SPEED_CTRL);
+ val |= SPEED_MODE_GEN2 << HALF_RATE_SHIFT |
+ SPEED_MODE_GEN2 << PHY_CONFIG_SHIFT |
+ SPEED_MODE_GEN2 << GEN2_EN_SHIFT;
+ writel_relaxed(val, priv->base + SATA_PORT_PHYCTL);
+
+ return 0;
+}
+
+static struct phy_ops hix5hd2_sata_phy_ops = {
+ .init = hix5hd2_sata_phy_init,
+ .owner = THIS_MODULE,
+};
+
+static int hix5hd2_sata_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct phy *phy;
+ struct hix5hd2_priv *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->base = devm_ioremap(dev, res->start, resource_size(res));
+ if (!priv->base)
+ return -ENOMEM;
+
+ priv->peri_ctrl = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "hisilicon,peripheral-syscon");
+ if (IS_ERR(priv->peri_ctrl))
+ priv->peri_ctrl = NULL;
+
+ phy = devm_phy_create(dev, &hix5hd2_sata_phy_ops, NULL);
+ if (IS_ERR(phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(phy);
+ }
+
+ phy_set_drvdata(phy, priv);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider))
+ return PTR_ERR(phy_provider);
+
+ return 0;
+}
+
+static const struct of_device_id hix5hd2_sata_phy_of_match[] = {
+ {.compatible = "hisilicon,hix5hd2-sata-phy",},
+ { },
+};
+MODULE_DEVICE_TABLE(of, hix5hd2_sata_phy_of_match);
+
+static struct platform_driver hix5hd2_sata_phy_driver = {
+ .probe = hix5hd2_sata_phy_probe,
+ .driver = {
+ .name = "hix5hd2-sata-phy",
+ .owner = THIS_MODULE,
+ .of_match_table = hix5hd2_sata_phy_of_match,
+ }
+};
+module_platform_driver(hix5hd2_sata_phy_driver);
+
+MODULE_AUTHOR("Jiancheng Xue <[email protected]>");
+MODULE_DESCRIPTION("HISILICON HIX5HD2 SATA PHY driver");
+MODULE_ALIAS("platform:hix5hd2-sata-phy");
+MODULE_LICENSE("GPL v2");
--
1.7.9.5