From: Alan Tull <[email protected]>
Patch 1: socfpga: hotplug: put cpu1 in wfi
Use WFI when putting CPU1 to sleep. Don't hold CPU1 in reset
since that results in increased power consumption. Only
briefly reset CPU1.
Patch 2: socfpga: support suspend to ram
* allocate space in ocram using sram driver
* Add a function in ocram to do suspend to ram and
place DDR in self-refresh
Alan Tull (2):
socfpga: hotplug: put cpu1 in wfi
socfpga: support suspend to ram
arch/arm/mach-socfpga/Kconfig | 1 +
arch/arm/mach-socfpga/Makefile | 1 +
arch/arm/mach-socfpga/core.h | 7 ++
arch/arm/mach-socfpga/platsmp.c | 19 ++--
arch/arm/mach-socfpga/pm.c | 150 ++++++++++++++++++++++++++++++++
arch/arm/mach-socfpga/self-refresh.S | 157 ++++++++++++++++++++++++++++++++++
arch/arm/mach-socfpga/socfpga.c | 10 +++
7 files changed, 337 insertions(+), 8 deletions(-)
create mode 100644 arch/arm/mach-socfpga/pm.c
create mode 100644 arch/arm/mach-socfpga/self-refresh.S
--
1.7.9.5
From: Alan Tull <[email protected]>
Use WFI when putting CPU1 to sleep. Don't hold CPU1 in reset
since that results in increased power consumption.
Reset CPU1 briefly during CPU1 bootup.
This has been tested for hotplug and suspend/resume and results
in no increased power consumption.
Signed-off-by: Alan Tull <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Dinh Nguyen <[email protected]>
---
v2: no need to flush the caches
clean up spacing in comments
replace a register offset with a macro
v3: Use writel, not __raw_writel
---
arch/arm/mach-socfpga/core.h | 3 +++
arch/arm/mach-socfpga/platsmp.c | 19 +++++++++++--------
2 files changed, 14 insertions(+), 8 deletions(-)
diff --git a/arch/arm/mach-socfpga/core.h b/arch/arm/mach-socfpga/core.h
index 572b8f7..953a9c0 100644
--- a/arch/arm/mach-socfpga/core.h
+++ b/arch/arm/mach-socfpga/core.h
@@ -21,6 +21,7 @@
#define __MACH_CORE_H
#define SOCFPGA_RSTMGR_CTRL 0x04
+#define SOCFPGA_RSTMGR_MODMPURST 0x10
#define SOCFPGA_RSTMGR_MODPERRST 0x14
#define SOCFPGA_RSTMGR_BRGMODRST 0x1c
@@ -28,6 +29,8 @@
#define RSTMGR_CTRL_SWCOLDRSTREQ 0x1 /* Cold Reset */
#define RSTMGR_CTRL_SWWARMRSTREQ 0x2 /* Warm Reset */
+#define RSTMGR_MPUMODRST_CPU1 0x2 /* CPU1 Reset */
+
extern void socfpga_secondary_startup(void);
extern void __iomem *socfpga_scu_base_addr;
diff --git a/arch/arm/mach-socfpga/platsmp.c b/arch/arm/mach-socfpga/platsmp.c
index 5356a72..9166dd4 100644
--- a/arch/arm/mach-socfpga/platsmp.c
+++ b/arch/arm/mach-socfpga/platsmp.c
@@ -34,17 +34,21 @@ static int socfpga_boot_secondary(unsigned int cpu, struct task_struct *idle)
int trampoline_size = &secondary_trampoline_end - &secondary_trampoline;
if (cpu1start_addr) {
+ /* This will put CPU #1 into reset. */
+ writel(RSTMGR_MPUMODRST_CPU1,
+ rst_manager_base_addr + SOCFPGA_RSTMGR_MODMPURST);
+
memcpy(phys_to_virt(0), &secondary_trampoline, trampoline_size);
- __raw_writel(virt_to_phys(socfpga_secondary_startup),
- (sys_manager_base_addr + (cpu1start_addr & 0x000000ff)));
+ writel(virt_to_phys(socfpga_secondary_startup),
+ sys_manager_base_addr + (cpu1start_addr & 0x000000ff));
flush_cache_all();
smp_wmb();
outer_clean_range(0, trampoline_size);
- /* This will release CPU #1 out of reset.*/
- __raw_writel(0, rst_manager_base_addr + 0x10);
+ /* This will release CPU #1 out of reset. */
+ writel(0, rst_manager_base_addr + SOCFPGA_RSTMGR_MODMPURST);
}
return 0;
@@ -86,10 +90,9 @@ static void __init socfpga_smp_prepare_cpus(unsigned int max_cpus)
*/
static void socfpga_cpu_die(unsigned int cpu)
{
- cpu_do_idle();
-
- /* We should have never returned from idle */
- panic("cpu %d unexpectedly exit from shutdown\n", cpu);
+ /* Do WFI. If we wake up early, go back into WFI */
+ while (1)
+ cpu_do_idle();
}
struct smp_operations socfpga_smp_ops __initdata = {
--
1.7.9.5
From: Alan Tull <[email protected]>
Add code that requests that the sdr controller go into
self-refresh mode. This code is run from ocram.
This patch assumes that u-boot has already configured sdr:
sdr.ctrlcfg.lowpwreq.selfrfshmask = 3
sdr.ctrlcfg.lowpwrtiming.clkdisablecycles = 8
sdr.ctrlcfg.dramtiming4.selfrfshexit = 512
How to suspend to ram:
$ echo enabled > \
/sys/devices/soc/ffc02000.serial0/tty/ttyS0/power/wakeup
$ echo -n mem > /sys/power/state
Signed-off-by: Alan Tull <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Steffen Trumtrar <[email protected]>
---
v2: use Generic on-chip SRAM driver to allocate ocram
rm fncpy_align since generic allocator handles alignment
check __arm_ioremap_exec return code
check for NULL pointers
add a comment regarding sdram controller configuration
v3: fix renamed #define
propagate socfpga_setup_ocram_self_refresh error code
---
arch/arm/mach-socfpga/Kconfig | 1 +
arch/arm/mach-socfpga/Makefile | 1 +
arch/arm/mach-socfpga/core.h | 4 +
arch/arm/mach-socfpga/pm.c | 150 ++++++++++++++++++++++++++++++++
arch/arm/mach-socfpga/self-refresh.S | 157 ++++++++++++++++++++++++++++++++++
arch/arm/mach-socfpga/socfpga.c | 10 +++
6 files changed, 323 insertions(+)
create mode 100644 arch/arm/mach-socfpga/pm.c
create mode 100644 arch/arm/mach-socfpga/self-refresh.S
diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig
index b5f8d75..81449da 100644
--- a/arch/arm/mach-socfpga/Kconfig
+++ b/arch/arm/mach-socfpga/Kconfig
@@ -4,6 +4,7 @@ config ARCH_SOCFPGA
select ARM_GIC
select CACHE_L2X0
select DW_APB_TIMER_OF
+ select GENERIC_ALLOCATOR
select GPIO_PL061 if GPIOLIB
select HAVE_ARM_SCU
select HAVE_ARM_TWD if SMP
diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile
index 6dd7a93..0591927 100644
--- a/arch/arm/mach-socfpga/Makefile
+++ b/arch/arm/mach-socfpga/Makefile
@@ -4,3 +4,4 @@
obj-y := socfpga.o
obj-$(CONFIG_SMP) += headsmp.o platsmp.o
+obj-$(CONFIG_SUSPEND) += pm.o self-refresh.o
diff --git a/arch/arm/mach-socfpga/core.h b/arch/arm/mach-socfpga/core.h
index 953a9c0..baa8392 100644
--- a/arch/arm/mach-socfpga/core.h
+++ b/arch/arm/mach-socfpga/core.h
@@ -39,6 +39,7 @@ extern void socfpga_sysmgr_init(void);
extern void __iomem *sys_manager_base_addr;
extern void __iomem *rst_manager_base_addr;
+extern void __iomem *sdr_ctl_base_addr;
extern struct smp_operations socfpga_smp_ops;
extern char secondary_trampoline, secondary_trampoline_end;
@@ -47,4 +48,7 @@ extern unsigned long cpu1start_addr;
#define SOCFPGA_SCU_VIRT_BASE 0xfffec000
+u32 socfpga_sdram_self_refresh(u32 sdr_base, u32 scu_base);
+extern unsigned int socfpga_sdram_self_refresh_sz;
+
#endif
diff --git a/arch/arm/mach-socfpga/pm.c b/arch/arm/mach-socfpga/pm.c
new file mode 100644
index 0000000..486f018
--- /dev/null
+++ b/arch/arm/mach-socfpga/pm.c
@@ -0,0 +1,150 @@
+/*
+ * arch/arm/mach-socfpga/pm.c
+ *
+ * Copyright (C) 2014 Altera Corporation. All rights reserved.
+ *
+ * with code from pm-imx6.c
+ * Copyright 2011-2014 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/bitops.h>
+#include <linux/genalloc.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/of_platform.h>
+#include <linux/suspend.h>
+#include <asm/suspend.h>
+#include <asm/fncpy.h>
+#include "core.h"
+
+/* Pointer to function copied to ocram */
+static u32 (*socfpga_sdram_self_refresh_in_ocram)(u32 sdr_base, u32 scu_base);
+
+static int socfpga_setup_ocram_self_refresh(void)
+{
+ struct platform_device *pdev;
+ phys_addr_t ocram_pbase;
+ struct device_node *np;
+ struct gen_pool *ocram_pool;
+ unsigned long ocram_base;
+ void __iomem *suspend_ocram_base;
+ int ret = 0;
+
+ np = of_find_compatible_node(NULL, NULL, "mmio-sram");
+ if (!np) {
+ pr_err("%s: Unable to find mmio-sram in dtb\n", __func__);
+ return 0;
+ }
+
+ pdev = of_find_device_by_node(np);
+ if (!pdev) {
+ pr_warn("%s: failed to find ocram device!\n", __func__);
+ ret = -ENODEV;
+ goto put_node;
+ }
+
+ ocram_pool = dev_get_gen_pool(&pdev->dev);
+ if (!ocram_pool) {
+ pr_warn("%s: ocram pool unavailable!\n", __func__);
+ ret = -ENODEV;
+ goto put_node;
+ }
+
+ ocram_base = gen_pool_alloc(ocram_pool, socfpga_sdram_self_refresh_sz);
+ if (!ocram_base) {
+ pr_warn("%s: unable to alloc ocram!\n", __func__);
+ ret = -ENOMEM;
+ goto put_node;
+ }
+
+ ocram_pbase = gen_pool_virt_to_phys(ocram_pool, ocram_base);
+
+ suspend_ocram_base = __arm_ioremap_exec(ocram_pbase,
+ socfpga_sdram_self_refresh_sz,
+ false);
+ if (!suspend_ocram_base) {
+ pr_warn("%s: __arm_ioremap_exec failed!\n", __func__);
+ ret = -ENOMEM;
+ goto put_node;
+ }
+
+ /* Copy the code that puts DDR in self refresh to ocram */
+ socfpga_sdram_self_refresh_in_ocram =
+ (void *)fncpy(suspend_ocram_base,
+ &socfpga_sdram_self_refresh,
+ socfpga_sdram_self_refresh_sz);
+
+ WARN(!socfpga_sdram_self_refresh_in_ocram,
+ "could not copy function to ocram");
+ if (!socfpga_sdram_self_refresh_in_ocram)
+ ret = -EFAULT;
+
+put_node:
+ of_node_put(np);
+
+ return ret;
+}
+
+static int socfpga_pm_suspend(unsigned long arg)
+{
+ u32 ret;
+
+ if (!sdr_ctl_base_addr || !socfpga_scu_base_addr)
+ return -EFAULT;
+
+ ret = socfpga_sdram_self_refresh_in_ocram(
+ (u32)sdr_ctl_base_addr, (u32)socfpga_scu_base_addr);
+
+ pr_debug("%s self-refresh loops request=%d exit=%d\n", __func__,
+ ret & 0xffff, (ret >> 16) & 0xffff);
+
+ return 0;
+}
+
+static int socfpga_pm_enter(suspend_state_t state)
+{
+ switch (state) {
+ case PM_SUSPEND_STANDBY:
+ case PM_SUSPEND_MEM:
+ outer_disable();
+ cpu_suspend(0, socfpga_pm_suspend);
+ outer_resume();
+ break;
+ default:
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static const struct platform_suspend_ops socfpga_pm_ops = {
+ .valid = suspend_valid_only_mem,
+ .enter = socfpga_pm_enter,
+};
+
+static int __init socfpga_pm_init(void)
+{
+ int ret;
+
+ ret = socfpga_setup_ocram_self_refresh();
+ if (ret)
+ return ret;
+
+ suspend_set_ops(&socfpga_pm_ops);
+ pr_info("SoCFPGA initialized for DDR self-refresh during suspend.\n");
+
+ return 0;
+}
+arch_initcall(socfpga_pm_init);
diff --git a/arch/arm/mach-socfpga/self-refresh.S b/arch/arm/mach-socfpga/self-refresh.S
new file mode 100644
index 0000000..93962d4
--- /dev/null
+++ b/arch/arm/mach-socfpga/self-refresh.S
@@ -0,0 +1,157 @@
+/*
+ * Copyright (C) 2014 Altera Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+#define SOCFPGA_SCU_CTRL_OFFS 0
+#define SCU_STANDBY_ENA 0x20
+#define MAX_LOOP_COUNT 1000
+
+/* Register offset */
+#define SDR_CTRLGRP_LOWPWREQ_ADDR 0x54
+#define SDR_CTRLGRP_LOWPWRACK_ADDR 0x58
+
+/* Bitfield positions */
+#define SELFRSHREQ_POS 3
+#define SELFRSHREQ_MASK 0x8
+
+#define SELFRFSHACK_POS 1
+#define SELFRFSHACK_MASK 0x2
+
+ /*
+ * This code assumes that the bootloader has already
+ * properly configured the sdram controller:
+ *
+ * sdr.ctrlcfg.lowpwreq.selfrfshmask = 3
+ * sdr.ctrlcfg.lowpwrtiming.clkdisablecycles = 8
+ * sdr.ctrlcfg.dramtiming4.selfrfshexit = 512
+ */
+
+ .arch armv7-a
+ .text
+ .align 3
+
+ /*
+ * socfpga_sdram_self_refresh
+ *
+ * r0 : sdr_ctl_base_addr
+ * r1 : socfpga_scu_base_addr
+ * r2 : temp storage of register values
+ * r3 : loop counter
+ * r4 : temp storage of return value
+ *
+ * return value: lower 16 bits: loop count going into self refresh
+ * upper 16 bits: loop count exiting self refresh
+ */
+ENTRY(socfpga_sdram_self_refresh)
+ stmfd sp!, {r4}
+
+ /*
+ * Enable SCU (snoop) standby mode.
+ *
+ * From the ARM Cortex-A9 MPCore Technical Reference Manual:
+ * "When set, SCU CLK is turned off when all processors are in WFI
+ * mode, there is no pending request on the ACP (if implemented), and
+ * there is no remaining activity in the SCU."
+ */
+ ldr r2, [r1, #SOCFPGA_SCU_CTRL_OFFS]
+ orr r2, r2, #SCU_STANDBY_ENA
+ str r2, [r1, #SOCFPGA_SCU_CTRL_OFFS]
+
+ /* Enable dynamic clock gating in the Power Control Register. */
+ mrc p15, 0, r2, c15, c0, 0
+ orr r2, r2, #1
+ mcr p15, 0, r2, c15, c0, 0
+
+ /* Enable self refresh: set sdr.ctrlgrp.lowpwreq.selfrshreq = 1 */
+ ldr r2, [r0, #SDR_CTRLGRP_LOWPWREQ_ADDR]
+ orr r2, r2, #SELFRSHREQ_MASK
+ str r2, [r0, #SDR_CTRLGRP_LOWPWREQ_ADDR]
+
+ /* Poll until sdr.ctrlgrp.lowpwrack.selfrfshack == 1 or hit max loops */
+ mov r3, #0
+while_ack_0:
+ ldr r2, [r0, #SDR_CTRLGRP_LOWPWRACK_ADDR]
+ and r2, r2, #SELFRFSHACK_MASK
+ cmp r2, #SELFRFSHACK_MASK
+ beq ack_1
+
+ add r3, #1
+ cmp r3, #MAX_LOOP_COUNT
+ bne while_ack_0
+
+ack_1:
+ mov r4, r3
+
+ /*
+ * Execute an ISB instruction to ensure that all of the
+ * CP15 register changes have been committed.
+ */
+ isb
+
+ /*
+ * Execute a barrier instruction to ensure that all cache,
+ * TLB and branch predictor maintenance operations issued
+ * by any CPU in the cluster have completed.
+ */
+ dsb
+ dmb
+
+ wfi
+
+ /* Disable self-refresh: set sdr.ctrlgrp.lowpwreq.selfrshreq = 0 */
+ ldr r2, [r0, #SDR_CTRLGRP_LOWPWREQ_ADDR]
+ bic r2, r2, #SELFRSHREQ_MASK
+ str r2, [r0, #SDR_CTRLGRP_LOWPWREQ_ADDR]
+
+ /* Poll until sdr.ctrlgrp.lowpwrack.selfrfshack == 0 or hit max loops */
+ mov r3, #0
+while_ack_1:
+ ldr r2, [r0, #SDR_CTRLGRP_LOWPWRACK_ADDR]
+ and r2, r2, #SELFRFSHACK_MASK
+ cmp r2, #SELFRFSHACK_MASK
+ bne ack_0
+
+ add r3, #1
+ cmp r3, #MAX_LOOP_COUNT
+ bne while_ack_1
+
+ack_0:
+ /*
+ * Prepare return value:
+ * Shift loop count for exiting self refresh into upper 16 bits.
+ * Leave loop count for requesting self refresh in lower 16 bits.
+ */
+ mov r3, r3, lsl #16
+ add r4, r4, r3
+
+ /* Disable dynamic clock gating in the Power Control Register. */
+ mrc p15, 0, r2, c15, c0, 0
+ bic r2, r2, #1
+ mcr p15, 0, r2, c15, c0, 0
+
+ /* Disable SCU standby mode */
+ ldr r2, [r1, #SOCFPGA_SCU_CTRL_OFFS]
+ bic r2, r2, #SCU_STANDBY_ENA
+ str r2, [r1, #SOCFPGA_SCU_CTRL_OFFS]
+
+ mov r0, r4 @ return value
+ ldmfd sp!, {r4}
+ bx lr @ return
+
+ENDPROC(socfpga_sdram_self_refresh)
+ENTRY(socfpga_sdram_self_refresh_sz)
+ .word . - socfpga_sdram_self_refresh
diff --git a/arch/arm/mach-socfpga/socfpga.c b/arch/arm/mach-socfpga/socfpga.c
index adbf383..34b4cc5 100644
--- a/arch/arm/mach-socfpga/socfpga.c
+++ b/arch/arm/mach-socfpga/socfpga.c
@@ -30,6 +30,7 @@ void __iomem *socfpga_scu_base_addr = ((void __iomem *)(SOCFPGA_SCU_VIRT_BASE));
void __iomem *sys_manager_base_addr;
void __iomem *rst_manager_base_addr;
unsigned long cpu1start_addr;
+void __iomem *sdr_ctl_base_addr;
static struct map_desc scu_io_desc __initdata = {
.virtual = SOCFPGA_SCU_VIRT_BASE,
@@ -77,6 +78,15 @@ void __init socfpga_sysmgr_init(void)
np = of_find_compatible_node(NULL, NULL, "altr,rst-mgr");
rst_manager_base_addr = of_iomap(np, 0);
+
+ np = of_find_compatible_node(NULL, NULL, "altr,sdr-ctl");
+ if (!np) {
+ pr_err("SOCFPGA: Unable to find sdr-ctl\n");
+ return;
+ }
+
+ sdr_ctl_base_addr = of_iomap(np, 0);
+ WARN_ON(!sdr_ctl_base_addr);
}
static void __init socfpga_init_irq(void)
--
1.7.9.5
On Tue 2014-10-14 14:33:38, [email protected] wrote:
> From: Alan Tull <[email protected]>
>
> Use WFI when putting CPU1 to sleep. Don't hold CPU1 in reset
> since that results in increased power consumption.
>
> Reset CPU1 briefly during CPU1 bootup.
>
> This has been tested for hotplug and suspend/resume and results
> in no increased power consumption.
>
> Signed-off-by: Alan Tull <[email protected]>
Acked-by: Pavel Machek <[email protected]>
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
On Tue 2014-10-14 14:33:39, [email protected] wrote:
> From: Alan Tull <[email protected]>
>
> Add code that requests that the sdr controller go into
> self-refresh mode. This code is run from ocram.
>
> This patch assumes that u-boot has already configured sdr:
> sdr.ctrlcfg.lowpwreq.selfrfshmask = 3
> sdr.ctrlcfg.lowpwrtiming.clkdisablecycles = 8
> sdr.ctrlcfg.dramtiming4.selfrfshexit = 512
>
> How to suspend to ram:
> $ echo enabled > \
> /sys/devices/soc/ffc02000.serial0/tty/ttyS0/power/wakeup
>
> $ echo -n mem > /sys/power/state
>
> Signed-off-by: Alan Tull <[email protected]>
Acked-by: Pavel Machek <[email protected]>
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
On Tue, 14 Oct 2014, [email protected] wrote:
> From: Alan Tull <[email protected]>
>
> Patch 1: socfpga: hotplug: put cpu1 in wfi
> Use WFI when putting CPU1 to sleep. Don't hold CPU1 in reset
> since that results in increased power consumption. Only
> briefly reset CPU1.
>
> Patch 2: socfpga: support suspend to ram
> * allocate space in ocram using sram driver
> * Add a function in ocram to do suspend to ram and
> place DDR in self-refresh
>
> Alan Tull (2):
> socfpga: hotplug: put cpu1 in wfi
> socfpga: support suspend to ram
>
> arch/arm/mach-socfpga/Kconfig | 1 +
> arch/arm/mach-socfpga/Makefile | 1 +
> arch/arm/mach-socfpga/core.h | 7 ++
> arch/arm/mach-socfpga/platsmp.c | 19 ++--
> arch/arm/mach-socfpga/pm.c | 150 ++++++++++++++++++++++++++++++++
> arch/arm/mach-socfpga/self-refresh.S | 157 ++++++++++++++++++++++++++++++++++
> arch/arm/mach-socfpga/socfpga.c | 10 +++
> 7 files changed, 337 insertions(+), 8 deletions(-)
> create mode 100644 arch/arm/mach-socfpga/pm.c
> create mode 100644 arch/arm/mach-socfpga/self-refresh.S
>
I've applied both patches. I just had to fixup a minor checkpatch error with
the 2nd patch:
ERROR: trailing whitespace
#284: FILE: arch/arm/mach-socfpga/self-refresh.S:34:
+^I/*^I$
total: 1 errors, 1 warnings, 354 lines checked
BR,
Dinh
On Wed, 15 Oct 2014, Pavel Machek wrote:
> On Tue 2014-10-14 14:33:39, [email protected] wrote:
> > From: Alan Tull <[email protected]>
> >
> > Add code that requests that the sdr controller go into
> > self-refresh mode. This code is run from ocram.
> >
> > This patch assumes that u-boot has already configured sdr:
> > sdr.ctrlcfg.lowpwreq.selfrfshmask = 3
> > sdr.ctrlcfg.lowpwrtiming.clkdisablecycles = 8
> > sdr.ctrlcfg.dramtiming4.selfrfshexit = 512
> >
> > How to suspend to ram:
> > $ echo enabled > \
> > /sys/devices/soc/ffc02000.serial0/tty/ttyS0/power/wakeup
> >
> > $ echo -n mem > /sys/power/state
> >
> > Signed-off-by: Alan Tull <[email protected]>
>
> Acked-by: Pavel Machek <[email protected]>
>
> --
> (english) http://www.livejournal.com/~pavelmachek
> (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
>
Thanks!
Alan
Hi Alan,
On 10/14/2014 02:33 PM, [email protected] wrote:
> From: Alan Tull <[email protected]>
>
> Add code that requests that the sdr controller go into
> self-refresh mode. This code is run from ocram.
>
> This patch assumes that u-boot has already configured sdr:
> sdr.ctrlcfg.lowpwreq.selfrfshmask = 3
> sdr.ctrlcfg.lowpwrtiming.clkdisablecycles = 8
> sdr.ctrlcfg.dramtiming4.selfrfshexit = 512
>
> How to suspend to ram:
> $ echo enabled > \
> /sys/devices/soc/ffc02000.serial0/tty/ttyS0/power/wakeup
>
> $ echo -n mem > /sys/power/state
>
> Signed-off-by: Alan Tull <[email protected]>
> Cc: Pavel Machek <[email protected]>
> Cc: Arnd Bergmann <[email protected]>
> Cc: Dinh Nguyen <[email protected]>
> Cc: Steffen Trumtrar <[email protected]>
> ---
> v2: use Generic on-chip SRAM driver to allocate ocram
> rm fncpy_align since generic allocator handles alignment
> check __arm_ioremap_exec return code
> check for NULL pointers
> add a comment regarding sdram controller configuration
> v3: fix renamed #define
> propagate socfpga_setup_ocram_self_refresh error code
> ---
> arch/arm/mach-socfpga/Kconfig | 1 +
> arch/arm/mach-socfpga/Makefile | 1 +
> arch/arm/mach-socfpga/core.h | 4 +
> arch/arm/mach-socfpga/pm.c | 150 ++++++++++++++++++++++++++++++++
> arch/arm/mach-socfpga/self-refresh.S | 157 ++++++++++++++++++++++++++++++++++
> arch/arm/mach-socfpga/socfpga.c | 10 +++
> 6 files changed, 323 insertions(+)
> create mode 100644 arch/arm/mach-socfpga/pm.c
> create mode 100644 arch/arm/mach-socfpga/self-refresh.S
>
> diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig
> index b5f8d75..81449da 100644
> --- a/arch/arm/mach-socfpga/Kconfig
> +++ b/arch/arm/mach-socfpga/Kconfig
> @@ -4,6 +4,7 @@ config ARCH_SOCFPGA
> select ARM_GIC
> select CACHE_L2X0
> select DW_APB_TIMER_OF
> + select GENERIC_ALLOCATOR
> select GPIO_PL061 if GPIOLIB
> select HAVE_ARM_SCU
> select HAVE_ARM_TWD if SMP
> diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile
> index 6dd7a93..0591927 100644
> --- a/arch/arm/mach-socfpga/Makefile
> +++ b/arch/arm/mach-socfpga/Makefile
> @@ -4,3 +4,4 @@
>
> obj-y := socfpga.o
> obj-$(CONFIG_SMP) += headsmp.o platsmp.o
> +obj-$(CONFIG_SUSPEND) += pm.o self-refresh.o
> diff --git a/arch/arm/mach-socfpga/core.h b/arch/arm/mach-socfpga/core.h
> index 953a9c0..baa8392 100644
> --- a/arch/arm/mach-socfpga/core.h
> +++ b/arch/arm/mach-socfpga/core.h
> @@ -39,6 +39,7 @@ extern void socfpga_sysmgr_init(void);
>
> extern void __iomem *sys_manager_base_addr;
> extern void __iomem *rst_manager_base_addr;
> +extern void __iomem *sdr_ctl_base_addr;
>
> extern struct smp_operations socfpga_smp_ops;
> extern char secondary_trampoline, secondary_trampoline_end;
> @@ -47,4 +48,7 @@ extern unsigned long cpu1start_addr;
>
> #define SOCFPGA_SCU_VIRT_BASE 0xfffec000
>
> +u32 socfpga_sdram_self_refresh(u32 sdr_base, u32 scu_base);
> +extern unsigned int socfpga_sdram_self_refresh_sz;
> +
> #endif
> diff --git a/arch/arm/mach-socfpga/pm.c b/arch/arm/mach-socfpga/pm.c
> new file mode 100644
> index 0000000..486f018
> --- /dev/null
> +++ b/arch/arm/mach-socfpga/pm.c
> @@ -0,0 +1,150 @@
> +/*
> + * arch/arm/mach-socfpga/pm.c
> + *
> + * Copyright (C) 2014 Altera Corporation. All rights reserved.
> + *
> + * with code from pm-imx6.c
> + * Copyright 2011-2014 Freescale Semiconductor, Inc.
> + * Copyright 2011 Linaro Ltd.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> + *
> + * You should have received a copy of the GNU General Public License along with
> + * this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/genalloc.h>
> +#include <linux/init.h>
> +#include <linux/io.h>
> +#include <linux/of_platform.h>
> +#include <linux/suspend.h>
> +#include <asm/suspend.h>
> +#include <asm/fncpy.h>
> +#include "core.h"
> +
> +/* Pointer to function copied to ocram */
> +static u32 (*socfpga_sdram_self_refresh_in_ocram)(u32 sdr_base, u32 scu_base);
> +
> +static int socfpga_setup_ocram_self_refresh(void)
> +{
> + struct platform_device *pdev;
> + phys_addr_t ocram_pbase;
> + struct device_node *np;
> + struct gen_pool *ocram_pool;
> + unsigned long ocram_base;
> + void __iomem *suspend_ocram_base;
> + int ret = 0;
> +
> + np = of_find_compatible_node(NULL, NULL, "mmio-sram");
> + if (!np) {
> + pr_err("%s: Unable to find mmio-sram in dtb\n", __func__);
> + return 0;
> + }
> +
> + pdev = of_find_device_by_node(np);
> + if (!pdev) {
> + pr_warn("%s: failed to find ocram device!\n", __func__);
> + ret = -ENODEV;
> + goto put_node;
> + }
> +
> + ocram_pool = dev_get_gen_pool(&pdev->dev);
> + if (!ocram_pool) {
> + pr_warn("%s: ocram pool unavailable!\n", __func__);
> + ret = -ENODEV;
> + goto put_node;
> + }
> +
> + ocram_base = gen_pool_alloc(ocram_pool, socfpga_sdram_self_refresh_sz);
> + if (!ocram_base) {
> + pr_warn("%s: unable to alloc ocram!\n", __func__);
> + ret = -ENOMEM;
> + goto put_node;
> + }
> +
> + ocram_pbase = gen_pool_virt_to_phys(ocram_pool, ocram_base);
> +
> + suspend_ocram_base = __arm_ioremap_exec(ocram_pbase,
> + socfpga_sdram_self_refresh_sz,
> + false);
> + if (!suspend_ocram_base) {
> + pr_warn("%s: __arm_ioremap_exec failed!\n", __func__);
> + ret = -ENOMEM;
> + goto put_node;
> + }
> +
> + /* Copy the code that puts DDR in self refresh to ocram */
> + socfpga_sdram_self_refresh_in_ocram =
> + (void *)fncpy(suspend_ocram_base,
> + &socfpga_sdram_self_refresh,
> + socfpga_sdram_self_refresh_sz);
> +
> + WARN(!socfpga_sdram_self_refresh_in_ocram,
> + "could not copy function to ocram");
> + if (!socfpga_sdram_self_refresh_in_ocram)
> + ret = -EFAULT;
> +
> +put_node:
> + of_node_put(np);
> +
> + return ret;
> +}
> +
> +static int socfpga_pm_suspend(unsigned long arg)
> +{
> + u32 ret;
> +
> + if (!sdr_ctl_base_addr || !socfpga_scu_base_addr)
> + return -EFAULT;
> +
> + ret = socfpga_sdram_self_refresh_in_ocram(
> + (u32)sdr_ctl_base_addr, (u32)socfpga_scu_base_addr);
> +
> + pr_debug("%s self-refresh loops request=%d exit=%d\n", __func__,
> + ret & 0xffff, (ret >> 16) & 0xffff);
> +
> + return 0;
> +}
> +
> +static int socfpga_pm_enter(suspend_state_t state)
> +{
> + switch (state) {
> + case PM_SUSPEND_STANDBY:
> + case PM_SUSPEND_MEM:
> + outer_disable();
> + cpu_suspend(0, socfpga_pm_suspend);
> + outer_resume();
> + break;
> + default:
> + return -EINVAL;
> + }
> + return 0;
> +}
> +
> +static const struct platform_suspend_ops socfpga_pm_ops = {
> + .valid = suspend_valid_only_mem,
> + .enter = socfpga_pm_enter,
> +};
> +
> +static int __init socfpga_pm_init(void)
> +{
> + int ret;
> +
> + ret = socfpga_setup_ocram_self_refresh();
> + if (ret)
> + return ret;
> +
> + suspend_set_ops(&socfpga_pm_ops);
> + pr_info("SoCFPGA initialized for DDR self-refresh during suspend.\n");
> +
> + return 0;
> +}
> +arch_initcall(socfpga_pm_init);
> diff --git a/arch/arm/mach-socfpga/self-refresh.S b/arch/arm/mach-socfpga/self-refresh.S
> new file mode 100644
> index 0000000..93962d4
> --- /dev/null
> +++ b/arch/arm/mach-socfpga/self-refresh.S
> @@ -0,0 +1,157 @@
> +/*
> + * Copyright (C) 2014 Altera Corporation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> + *
> + * You should have received a copy of the GNU General Public License along with
> + * this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +#include <linux/linkage.h>
> +#include <asm/assembler.h>
> +
> +#define SOCFPGA_SCU_CTRL_OFFS 0
> +#define SCU_STANDBY_ENA 0x20
> +#define MAX_LOOP_COUNT 1000
> +
> +/* Register offset */
> +#define SDR_CTRLGRP_LOWPWREQ_ADDR 0x54
> +#define SDR_CTRLGRP_LOWPWRACK_ADDR 0x58
> +
> +/* Bitfield positions */
> +#define SELFRSHREQ_POS 3
> +#define SELFRSHREQ_MASK 0x8
> +
> +#define SELFRFSHACK_POS 1
> +#define SELFRFSHACK_MASK 0x2
> +
> + /*
> + * This code assumes that the bootloader has already
> + * properly configured the sdram controller:
> + *
> + * sdr.ctrlcfg.lowpwreq.selfrfshmask = 3
> + * sdr.ctrlcfg.lowpwrtiming.clkdisablecycles = 8
> + * sdr.ctrlcfg.dramtiming4.selfrfshexit = 512
> + */
> +
> + .arch armv7-a
> + .text
> + .align 3
> +
> + /*
> + * socfpga_sdram_self_refresh
> + *
> + * r0 : sdr_ctl_base_addr
> + * r1 : socfpga_scu_base_addr
> + * r2 : temp storage of register values
> + * r3 : loop counter
> + * r4 : temp storage of return value
> + *
> + * return value: lower 16 bits: loop count going into self refresh
> + * upper 16 bits: loop count exiting self refresh
> + */
> +ENTRY(socfpga_sdram_self_refresh)
> + stmfd sp!, {r4}
> +
> + /*
> + * Enable SCU (snoop) standby mode.
> + *
> + * From the ARM Cortex-A9 MPCore Technical Reference Manual:
> + * "When set, SCU CLK is turned off when all processors are in WFI
> + * mode, there is no pending request on the ACP (if implemented), and
> + * there is no remaining activity in the SCU."
> + */
> + ldr r2, [r1, #SOCFPGA_SCU_CTRL_OFFS]
> + orr r2, r2, #SCU_STANDBY_ENA
> + str r2, [r1, #SOCFPGA_SCU_CTRL_OFFS]
> +
> + /* Enable dynamic clock gating in the Power Control Register. */
> + mrc p15, 0, r2, c15, c0, 0
> + orr r2, r2, #1
> + mcr p15, 0, r2, c15, c0, 0
> +
> + /* Enable self refresh: set sdr.ctrlgrp.lowpwreq.selfrshreq = 1 */
> + ldr r2, [r0, #SDR_CTRLGRP_LOWPWREQ_ADDR]
> + orr r2, r2, #SELFRSHREQ_MASK
> + str r2, [r0, #SDR_CTRLGRP_LOWPWREQ_ADDR]
> +
> + /* Poll until sdr.ctrlgrp.lowpwrack.selfrfshack == 1 or hit max loops */
> + mov r3, #0
> +while_ack_0:
> + ldr r2, [r0, #SDR_CTRLGRP_LOWPWRACK_ADDR]
> + and r2, r2, #SELFRFSHACK_MASK
> + cmp r2, #SELFRFSHACK_MASK
> + beq ack_1
> +
> + add r3, #1
> + cmp r3, #MAX_LOOP_COUNT
> + bne while_ack_0
> +
> +ack_1:
> + mov r4, r3
> +
> + /*
> + * Execute an ISB instruction to ensure that all of the
> + * CP15 register changes have been committed.
> + */
> + isb
> +
> + /*
> + * Execute a barrier instruction to ensure that all cache,
> + * TLB and branch predictor maintenance operations issued
> + * by any CPU in the cluster have completed.
> + */
> + dsb
> + dmb
> +
> + wfi
> +
> + /* Disable self-refresh: set sdr.ctrlgrp.lowpwreq.selfrshreq = 0 */
> + ldr r2, [r0, #SDR_CTRLGRP_LOWPWREQ_ADDR]
> + bic r2, r2, #SELFRSHREQ_MASK
> + str r2, [r0, #SDR_CTRLGRP_LOWPWREQ_ADDR]
> +
> + /* Poll until sdr.ctrlgrp.lowpwrack.selfrfshack == 0 or hit max loops */
> + mov r3, #0
> +while_ack_1:
> + ldr r2, [r0, #SDR_CTRLGRP_LOWPWRACK_ADDR]
> + and r2, r2, #SELFRFSHACK_MASK
> + cmp r2, #SELFRFSHACK_MASK
> + bne ack_0
> +
> + add r3, #1
> + cmp r3, #MAX_LOOP_COUNT
> + bne while_ack_1
> +
> +ack_0:
> + /*
> + * Prepare return value:
> + * Shift loop count for exiting self refresh into upper 16 bits.
> + * Leave loop count for requesting self refresh in lower 16 bits.
> + */
> + mov r3, r3, lsl #16
> + add r4, r4, r3
> +
> + /* Disable dynamic clock gating in the Power Control Register. */
> + mrc p15, 0, r2, c15, c0, 0
> + bic r2, r2, #1
> + mcr p15, 0, r2, c15, c0, 0
> +
> + /* Disable SCU standby mode */
> + ldr r2, [r1, #SOCFPGA_SCU_CTRL_OFFS]
> + bic r2, r2, #SCU_STANDBY_ENA
> + str r2, [r1, #SOCFPGA_SCU_CTRL_OFFS]
> +
> + mov r0, r4 @ return value
> + ldmfd sp!, {r4}
> + bx lr @ return
> +
> +ENDPROC(socfpga_sdram_self_refresh)
> +ENTRY(socfpga_sdram_self_refresh_sz)
> + .word . - socfpga_sdram_self_refresh
> diff --git a/arch/arm/mach-socfpga/socfpga.c b/arch/arm/mach-socfpga/socfpga.c
> index adbf383..34b4cc5 100644
> --- a/arch/arm/mach-socfpga/socfpga.c
> +++ b/arch/arm/mach-socfpga/socfpga.c
> @@ -30,6 +30,7 @@ void __iomem *socfpga_scu_base_addr = ((void __iomem *)(SOCFPGA_SCU_VIRT_BASE));
> void __iomem *sys_manager_base_addr;
> void __iomem *rst_manager_base_addr;
> unsigned long cpu1start_addr;
> +void __iomem *sdr_ctl_base_addr;
>
> static struct map_desc scu_io_desc __initdata = {
> .virtual = SOCFPGA_SCU_VIRT_BASE,
> @@ -77,6 +78,15 @@ void __init socfpga_sysmgr_init(void)
>
> np = of_find_compatible_node(NULL, NULL, "altr,rst-mgr");
> rst_manager_base_addr = of_iomap(np, 0);
> +
> + np = of_find_compatible_node(NULL, NULL, "altr,sdr-ctl");
> + if (!np) {
> + pr_err("SOCFPGA: Unable to find sdr-ctl\n");
> + return;
> + }
> +
> + sdr_ctl_base_addr = of_iomap(np, 0);
> + WARN_ON(!sdr_ctl_base_addr);
> }
>
> static void __init socfpga_init_irq(void)
>
When I went to apply this, I noticed that the "altr,sdr-ctl" binding has
not yet been defined anywhere. It looks like like you are using this
binding to get the base address of the SDRAM controller for the
self-refresh code. Since the self-refresh code is very specific to the
SOCFPGA platform, would it be easier to define the SDRAM controller's
base address in the assembly? If not, then you will have to define the
"altr,adr-ctl" binding.
Dinh