This patch series deals with a removing a IP feature that can be found
on all currently supported Marvell Ethernet IP (pxa168_eth, mv643xx_eth,
mvneta). The MAC IP allows to automatically perform PHY auto-negotiation
without software interaction.
However, this feature (a) fundamentally clashes with the way libphy works
and (b) is unable to deal with quirky PHYs that require special treatment.
In this series, pxa168_eth driver is rewritten to completely disable that
feature and properly deal with libphy provided PHYs.
As usual, a branch on top of v3.18-rc1 can be found at
git://git.infradead.org/users/hesselba/linux-berlin.git devel/bg2-bg2cd-eth-v2
Patches 1-5 should go through David's net tree, I'll pick up the DT patches
6-9.
There have been some changes,
compared to the RFT
- added phy-connection-type property to BG2Q PHY DT node
- bail out from pxa168_eth_adjust_link when there is no change in
PHY parameters. Also, add a call to phy_print_status.
compared to v1
- move phy-connection-type to ethernet node instead of PHY node
Patch 1 adds support for Marvell 88E3016 FastEthernet PHY that is also
integrated in Marvell Berlin BG2/BG2CD SoCs.
Patch 2 allows to pass phy_interface_t on pxa168_eth platform_data that
is only used by mach-mmp/gplug. From the board setup, I guessed gplug's
PHY is connected via RMII. The patch still isn't even compile tested.
Patches 3-5 prepare proper libphy handling and finally remove all in-driver
PHY mangling related to the feature explained above.
Patches 6-9 add corresponding ethernet DT nodes to BG2, BG2CD, add a
phy-connection-type property to BG2Q and enable ethernet on BG2-based Sony
NSZ-GS7. I have tested all this on GS7 successfully with ip=dhcp on 100M FD.
Antoine Ténart (1):
ARM: berlin: Add phy-connection-type to BG2Q Ethernet
Sebastian Hesselbarth (8):
phy: marvell: Add support for 88E3016 FastEthernet PHY
net: pxa168_eth: Provide phy_interface mode on platform_data
net: pxa168_eth: Prepare proper libphy handling
net: pxa168_eth: Remove HW auto-negotiaion
net: pxa168_eth: Remove in-driver PHY mangling
ARM: berlin: Add BG2 ethernet DT nodes
ARM: berlin: Add BG2CD ethernet DT nodes
ARM: berlin: Enable ethernet on Sony NSZ-GS7
arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts | 2 +
arch/arm/boot/dts/berlin2.dtsi | 36 +++++
arch/arm/boot/dts/berlin2cd.dtsi | 36 +++++
arch/arm/boot/dts/berlin2q.dtsi | 1 +
arch/arm/mach-mmp/gplugd.c | 2 +
drivers/net/ethernet/marvell/pxa168_eth.c | 248 ++++++++++++-----------------
drivers/net/phy/marvell.c | 46 ++++++
include/linux/marvell_phy.h | 1 +
include/linux/pxa168_eth.h | 1 +
9 files changed, 225 insertions(+), 148 deletions(-)
---
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
--
2.1.1
Marvell Ethernet IP supports PHY negotiation driven by HW. This
fundamentally clashes with libphy (software) driven negotiation and
also cannot cope with quirky PHYs. Therefore, always disable any HW
negotiation features and properly use libphy's phy_device.
Tested-by: Antoine Ténart <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
drivers/net/ethernet/marvell/pxa168_eth.c | 100 +++++++++++++++++++++++++-----
1 file changed, 85 insertions(+), 15 deletions(-)
diff --git a/drivers/net/ethernet/marvell/pxa168_eth.c b/drivers/net/ethernet/marvell/pxa168_eth.c
index 3918887e09c5..ca60fa24d2ed 100644
--- a/drivers/net/ethernet/marvell/pxa168_eth.c
+++ b/drivers/net/ethernet/marvell/pxa168_eth.c
@@ -106,6 +106,7 @@
#define SDMA_CMD_ERD (1 << 7)
/* Bit definitions of the Port Config Reg */
+#define PCR_DUPLEX_FULL (1 << 15)
#define PCR_HS (1 << 12)
#define PCR_EN (1 << 7)
#define PCR_PM (1 << 0)
@@ -113,11 +114,17 @@
/* Bit definitions of the Port Config Extend Reg */
#define PCXR_2BSM (1 << 28)
#define PCXR_DSCP_EN (1 << 21)
+#define PCXR_RMII_EN (1 << 20)
+#define PCXR_AN_SPEED_DIS (1 << 19)
+#define PCXR_SPEED_100 (1 << 18)
#define PCXR_MFL_1518 (0 << 14)
#define PCXR_MFL_1536 (1 << 14)
#define PCXR_MFL_2048 (2 << 14)
#define PCXR_MFL_64K (3 << 14)
+#define PCXR_FLOWCTL_DIS (1 << 12)
#define PCXR_FLP (1 << 11)
+#define PCXR_AN_FLOWCTL_DIS (1 << 10)
+#define PCXR_AN_DUPLEX_DIS (1 << 9)
#define PCXR_PRIO_TX_OFF 3
#define PCXR_TX_HIGH_PRI (7 << PCXR_PRIO_TX_OFF)
@@ -272,6 +279,7 @@ enum hash_table_entry {
static int pxa168_get_settings(struct net_device *dev, struct ethtool_cmd *cmd);
static int pxa168_set_settings(struct net_device *dev, struct ethtool_cmd *cmd);
static int pxa168_init_hw(struct pxa168_eth_private *pep);
+static int pxa168_init_phy(struct net_device *dev);
static void eth_port_reset(struct net_device *dev);
static void eth_port_start(struct net_device *dev);
static int pxa168_eth_open(struct net_device *dev);
@@ -658,14 +666,7 @@ static void eth_port_start(struct net_device *dev)
struct pxa168_eth_private *pep = netdev_priv(dev);
int tx_curr_desc, rx_curr_desc;
- /* Perform PHY reset, if there is a PHY. */
- if (pep->phy != NULL) {
- struct ethtool_cmd cmd;
-
- pxa168_get_settings(pep->dev, &cmd);
- phy_init_hw(pep->phy);
- pxa168_set_settings(pep->dev, &cmd);
- }
+ phy_start(pep->phy);
/* Assignment of Tx CTRP of given queue */
tx_curr_desc = pep->tx_curr_desc_q;
@@ -720,6 +721,8 @@ static void eth_port_reset(struct net_device *dev)
val = rdl(pep, PORT_CONFIG);
val &= ~PCR_EN;
wrl(pep, PORT_CONFIG, val);
+
+ phy_stop(pep->phy);
}
/*
@@ -981,8 +984,11 @@ static int set_port_config_ext(struct pxa168_eth_private *pep)
skb_size = PCXR_MFL_64K;
/* Extended Port Configuration */
- wrl(pep,
- PORT_CONFIG_EXT, PCXR_2BSM | /* Two byte prefix aligns IP hdr */
+ wrl(pep, PORT_CONFIG_EXT,
+ PCXR_AN_SPEED_DIS | /* Disable HW AN */
+ PCXR_AN_DUPLEX_DIS |
+ PCXR_AN_FLOWCTL_DIS |
+ PCXR_2BSM | /* Two byte prefix aligns IP hdr */
PCXR_DSCP_EN | /* Enable DSCP in IP */
skb_size | PCXR_FLP | /* do not force link pass */
PCXR_TX_HIGH_PRI); /* Transmit - high priority queue */
@@ -990,6 +996,69 @@ static int set_port_config_ext(struct pxa168_eth_private *pep)
return 0;
}
+static void pxa168_eth_adjust_link(struct net_device *dev)
+{
+ struct pxa168_eth_private *pep = netdev_priv(dev);
+ struct phy_device *phy = pep->phy;
+ u32 cfg, cfg_o = rdl(pep, PORT_CONFIG);
+ u32 cfgext, cfgext_o = rdl(pep, PORT_CONFIG_EXT);
+
+ cfg = cfg_o & ~PCR_DUPLEX_FULL;
+ cfgext = cfgext_o & ~(PCXR_SPEED_100 | PCXR_FLOWCTL_DIS | PCXR_RMII_EN);
+
+ if (phy->interface == PHY_INTERFACE_MODE_RMII)
+ cfgext |= PCXR_RMII_EN;
+ if (phy->speed == SPEED_100)
+ cfgext |= PCXR_SPEED_100;
+ if (phy->duplex)
+ cfg |= PCR_DUPLEX_FULL;
+ if (!phy->pause)
+ cfgext |= PCXR_FLOWCTL_DIS;
+
+ /* Bail out if there has nothing changed */
+ if (cfg == cfg_o && cfgext == cfgext_o)
+ return;
+
+ wrl(pep, PORT_CONFIG, cfg);
+ wrl(pep, PORT_CONFIG_EXT, cfgext);
+
+ phy_print_status(phy);
+}
+
+static int pxa168_init_phy(struct net_device *dev)
+{
+ struct pxa168_eth_private *pep = netdev_priv(dev);
+ struct ethtool_cmd cmd;
+ int err;
+
+ if (pep->phy)
+ return 0;
+
+ pep->phy = mdiobus_scan(pep->smi_bus, pep->phy_addr);
+ if (!pep->phy)
+ return -ENODEV;
+
+ err = phy_connect_direct(dev, pep->phy, pxa168_eth_adjust_link,
+ pep->phy_intf);
+ if (err)
+ return err;
+
+ err = pxa168_get_settings(dev, &cmd);
+ if (err)
+ return err;
+
+ cmd.phy_address = pep->phy_addr;
+ cmd.speed = pep->phy_speed;
+ cmd.duplex = pep->phy_duplex;
+ cmd.advertising = PHY_BASIC_FEATURES;
+ cmd.autoneg = AUTONEG_ENABLE;
+
+ if (cmd.speed != 0)
+ cmd.autoneg = AUTONEG_DISABLE;
+
+ return pxa168_set_settings(dev, &cmd);
+}
+
static int pxa168_init_hw(struct pxa168_eth_private *pep)
{
int err = 0;
@@ -1136,6 +1205,10 @@ static int pxa168_eth_open(struct net_device *dev)
struct pxa168_eth_private *pep = netdev_priv(dev);
int err;
+ err = pxa168_init_phy(dev);
+ if (err)
+ return err;
+
err = request_irq(dev->irq, pxa168_eth_int_handler, 0, dev->name, dev);
if (err) {
dev_err(&dev->dev, "can't assign irq\n");
@@ -1596,9 +1669,6 @@ static int pxa168_eth_probe(struct platform_device *pdev)
goto err_free_mdio;
pxa168_init_hw(pep);
- err = ethernet_phy_setup(dev);
- if (err)
- goto err_mdiobus;
SET_NETDEV_DEV(dev, &pdev->dev);
err = register_netdev(dev);
if (err)
@@ -1629,13 +1699,13 @@ static int pxa168_eth_remove(struct platform_device *pdev)
pep->htpr, pep->htpr_dma);
pep->htpr = NULL;
}
+ if (pep->phy)
+ phy_disconnect(pep->phy);
if (pep->clk) {
clk_disable(pep->clk);
clk_put(pep->clk);
pep->clk = NULL;
}
- if (pep->phy != NULL)
- phy_detach(pep->phy);
iounmap(pep->base);
pep->base = NULL;
--
2.1.1
Marvell Berlin BG2 based Sony NSZ-GS7 has one ethernet controller
connected to rear RJ45 jack. Enable it by default.
Tested-by: Antoine Ténart <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts b/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts
index c72bfd468d10..27f2f0ad7562 100644
--- a/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts
+++ b/arch/arm/boot/dts/berlin2-sony-nsz-gs7.dts
@@ -26,4 +26,6 @@
};
};
+ð1 { status = "okay"; };
+
&uart0 { status = "okay"; };
--
2.1.1
Marvell 88E3016 is a FastEthernet PHY that also can be found in Marvell
Berlin SoCs as integrated PHY.
Tested-by: Antoine Ténart <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
drivers/net/phy/marvell.c | 46 +++++++++++++++++++++++++++++++++++++++++++++
include/linux/marvell_phy.h | 1 +
2 files changed, 47 insertions(+)
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index bd37e45c89c0..d2b2f2f795d5 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -118,6 +118,9 @@
#define MII_M1116R_CONTROL_REG_MAC 21
+#define MII_88E3016_PHY_SPEC_CTRL 0x10
+#define MII_88E3016_DISABLE_SCRAMBLER 0x0200
+#define MII_88E3016_AUTO_MDIX_CROSSOVER 0x0030
MODULE_DESCRIPTION("Marvell PHY driver");
MODULE_AUTHOR("Andy Fleming");
@@ -434,6 +437,25 @@ static int m88e1116r_config_init(struct phy_device *phydev)
return 0;
}
+static int m88e3016_config_init(struct phy_device *phydev)
+{
+ int reg;
+
+ /* Enable Scrambler and Auto-Crossover */
+ reg = phy_read(phydev, MII_88E3016_PHY_SPEC_CTRL);
+ if (reg < 0)
+ return reg;
+
+ reg &= ~MII_88E3016_DISABLE_SCRAMBLER;
+ reg |= MII_88E3016_AUTO_MDIX_CROSSOVER;
+
+ reg = phy_write(phydev, MII_88E3016_PHY_SPEC_CTRL, reg);
+ if (reg < 0)
+ return reg;
+
+ return 0;
+}
+
static int m88e1111_config_init(struct phy_device *phydev)
{
int err;
@@ -770,6 +792,12 @@ static int marvell_read_status(struct phy_device *phydev)
return 0;
}
+static int marvell_aneg_done(struct phy_device *phydev)
+{
+ int retval = phy_read(phydev, MII_M1011_PHY_STATUS);
+ return (retval < 0) ? retval : (retval & MII_M1011_PHY_STATUS_RESOLVED);
+}
+
static int m88e1121_did_interrupt(struct phy_device *phydev)
{
int imask;
@@ -1050,6 +1078,23 @@ static struct phy_driver marvell_drivers[] = {
.suspend = &genphy_suspend,
.driver = { .owner = THIS_MODULE },
},
+ {
+ .phy_id = MARVELL_PHY_ID_88E3016,
+ .phy_id_mask = MARVELL_PHY_ID_MASK,
+ .name = "Marvell 88E3016",
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_HAS_INTERRUPT,
+ .config_aneg = &genphy_config_aneg,
+ .config_init = &m88e3016_config_init,
+ .aneg_done = &marvell_aneg_done,
+ .read_status = &marvell_read_status,
+ .ack_interrupt = &marvell_ack_interrupt,
+ .config_intr = &marvell_config_intr,
+ .did_interrupt = &m88e1121_did_interrupt,
+ .resume = &genphy_resume,
+ .suspend = &genphy_suspend,
+ .driver = { .owner = THIS_MODULE },
+ },
};
static int __init marvell_init(void)
@@ -1079,6 +1124,7 @@ static struct mdio_device_id __maybe_unused marvell_tbl[] = {
{ MARVELL_PHY_ID_88E1318S, MARVELL_PHY_ID_MASK },
{ MARVELL_PHY_ID_88E1116R, MARVELL_PHY_ID_MASK },
{ MARVELL_PHY_ID_88E1510, MARVELL_PHY_ID_MASK },
+ { MARVELL_PHY_ID_88E3016, MARVELL_PHY_ID_MASK },
{ }
};
diff --git a/include/linux/marvell_phy.h b/include/linux/marvell_phy.h
index 8e9a029e093d..e6982ac3200d 100644
--- a/include/linux/marvell_phy.h
+++ b/include/linux/marvell_phy.h
@@ -16,6 +16,7 @@
#define MARVELL_PHY_ID_88E1318S 0x01410e90
#define MARVELL_PHY_ID_88E1116R 0x01410e40
#define MARVELL_PHY_ID_88E1510 0x01410dd0
+#define MARVELL_PHY_ID_88E3016 0x01410e60
/* struct phy_device dev_flags definitions */
#define MARVELL_PHY_M1145_FLAGS_RESISTANCE 0x00000001
--
2.1.1
Marvell BG2CD has two fast ethernet controllers with internal PHY,
add the corresponding nodes to SoC dtsi.
Tested-by: Antoine Ténart <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
Changelog:
v1->v2:
- move phy-connection-type to controller node instead of PHY node
(Reported by Sergei Shtylyov)
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
arch/arm/boot/dts/berlin2cd.dtsi | 36 ++++++++++++++++++++++++++++++++++++
1 file changed, 36 insertions(+)
diff --git a/arch/arm/boot/dts/berlin2cd.dtsi b/arch/arm/boot/dts/berlin2cd.dtsi
index cc1df65da504..762b93b80835 100644
--- a/arch/arm/boot/dts/berlin2cd.dtsi
+++ b/arch/arm/boot/dts/berlin2cd.dtsi
@@ -66,6 +66,42 @@
clocks = <&chip CLKID_TWD>;
};
+ eth1: ethernet@b90000 {
+ compatible = "marvell,pxa168-eth";
+ reg = <0xb90000 0x10000>;
+ clocks = <&chip CLKID_GETH1>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ /* set by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy-connection-type = "mii";
+ phy-handle = <ðphy1>;
+ status = "disabled";
+
+ ethphy1: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+
+ eth0: ethernet@e50000 {
+ compatible = "marvell,pxa168-eth";
+ reg = <0xe50000 0x10000>;
+ clocks = <&chip CLKID_GETH0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ /* set by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy-connection-type = "mii";
+ phy-handle = <ðphy0>;
+ status = "disabled";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+
apb@e80000 {
compatible = "simple-bus";
#address-cells = <1>;
--
2.1.1
With properly using libphy PHYs now, remove the in-driver PHY
mangling.
Tested-by: Antoine Ténart <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
drivers/net/ethernet/marvell/pxa168_eth.c | 126 ------------------------------
1 file changed, 126 deletions(-)
diff --git a/drivers/net/ethernet/marvell/pxa168_eth.c b/drivers/net/ethernet/marvell/pxa168_eth.c
index ca60fa24d2ed..bee4c369f0fe 100644
--- a/drivers/net/ethernet/marvell/pxa168_eth.c
+++ b/drivers/net/ethernet/marvell/pxa168_eth.c
@@ -177,7 +177,6 @@
#define LINK_UP (1 << 3)
/* Bit definitions for work to be done */
-#define WORK_LINK (1 << 0)
#define WORK_TX_DONE (1 << 1)
/*
@@ -284,7 +283,6 @@ static void eth_port_reset(struct net_device *dev);
static void eth_port_start(struct net_device *dev);
static int pxa168_eth_open(struct net_device *dev);
static int pxa168_eth_stop(struct net_device *dev);
-static int ethernet_phy_setup(struct net_device *dev);
static inline u32 rdl(struct pxa168_eth_private *pep, int offset)
{
@@ -316,26 +314,6 @@ static void abort_dma(struct pxa168_eth_private *pep)
netdev_err(pep->dev, "%s : DMA Stuck\n", __func__);
}
-static int ethernet_phy_get(struct pxa168_eth_private *pep)
-{
- unsigned int reg_data;
-
- reg_data = rdl(pep, PHY_ADDRESS);
-
- return (reg_data >> (5 * pep->port_num)) & 0x1f;
-}
-
-static void ethernet_phy_set_addr(struct pxa168_eth_private *pep, int phy_addr)
-{
- u32 reg_data;
- int addr_shift = 5 * pep->port_num;
-
- reg_data = rdl(pep, PHY_ADDRESS);
- reg_data &= ~(0x1f << addr_shift);
- reg_data |= (phy_addr & 0x1f) << addr_shift;
- wrl(pep, PHY_ADDRESS, reg_data);
-}
-
static void rxq_refill(struct net_device *dev)
{
struct pxa168_eth_private *pep = netdev_priv(dev);
@@ -890,43 +868,9 @@ static int pxa168_eth_collect_events(struct pxa168_eth_private *pep,
}
if (icr & ICR_RXBUF)
ret = 1;
- if (icr & ICR_MII_CH) {
- pep->work_todo |= WORK_LINK;
- ret = 1;
- }
return ret;
}
-static void handle_link_event(struct pxa168_eth_private *pep)
-{
- struct net_device *dev = pep->dev;
- u32 port_status;
- int speed;
- int duplex;
- int fc;
-
- port_status = rdl(pep, PORT_STATUS);
- if (!(port_status & LINK_UP)) {
- if (netif_carrier_ok(dev)) {
- netdev_info(dev, "link down\n");
- netif_carrier_off(dev);
- txq_reclaim(dev, 1);
- }
- return;
- }
- if (port_status & PORT_SPEED_100)
- speed = 100;
- else
- speed = 10;
-
- duplex = (port_status & FULL_DUPLEX) ? 1 : 0;
- fc = (port_status & FLOW_CONTROL_DISABLED) ? 0 : 1;
- netdev_info(dev, "link up, %d Mb/s, %s duplex, flow control %sabled\n",
- speed, duplex ? "full" : "half", fc ? "en" : "dis");
- if (!netif_carrier_ok(dev))
- netif_carrier_on(dev);
-}
-
static irqreturn_t pxa168_eth_int_handler(int irq, void *dev_id)
{
struct net_device *dev = (struct net_device *)dev_id;
@@ -1307,10 +1251,6 @@ static int pxa168_rx_poll(struct napi_struct *napi, int budget)
struct net_device *dev = pep->dev;
int work_done = 0;
- if (unlikely(pep->work_todo & WORK_LINK)) {
- pep->work_todo &= ~(WORK_LINK);
- handle_link_event(pep);
- }
/*
* We call txq_reclaim every time since in NAPI interupts are disabled
* and due to this we miss the TX_DONE interrupt,which is not updated in
@@ -1433,72 +1373,6 @@ static int pxa168_eth_do_ioctl(struct net_device *dev, struct ifreq *ifr,
return -EOPNOTSUPP;
}
-static struct phy_device *phy_scan(struct pxa168_eth_private *pep, int phy_addr)
-{
- struct mii_bus *bus = pep->smi_bus;
- struct phy_device *phydev;
- int start;
- int num;
- int i;
-
- if (phy_addr == PXA168_ETH_PHY_ADDR_DEFAULT) {
- /* Scan entire range */
- start = ethernet_phy_get(pep);
- num = 32;
- } else {
- /* Use phy addr specific to platform */
- start = phy_addr & 0x1f;
- num = 1;
- }
- phydev = NULL;
- for (i = 0; i < num; i++) {
- int addr = (start + i) & 0x1f;
- if (bus->phy_map[addr] == NULL)
- mdiobus_scan(bus, addr);
-
- if (phydev == NULL) {
- phydev = bus->phy_map[addr];
- if (phydev != NULL)
- ethernet_phy_set_addr(pep, addr);
- }
- }
-
- return phydev;
-}
-
-static void phy_init(struct pxa168_eth_private *pep)
-{
- struct phy_device *phy = pep->phy;
-
- phy_attach(pep->dev, dev_name(&phy->dev), pep->phy_intf);
-
- phy->speed = pep->phy_speed;
- phy->duplex = pep->phy_duplex;
- phy->autoneg = AUTONEG_ENABLE;
- phy->supported &= PHY_BASIC_FEATURES;
- phy->advertising = phy->supported | ADVERTISED_Autoneg;
-
- if (pep->phy_speed != 0) {
- phy->autoneg = AUTONEG_DISABLE;
- phy->advertising = 0;
- }
-
- phy_start_aneg(phy);
-}
-
-static int ethernet_phy_setup(struct net_device *dev)
-{
- struct pxa168_eth_private *pep = netdev_priv(dev);
-
- pep->phy = phy_scan(pep, pep->phy_addr & 0x1f);
- if (pep->phy != NULL)
- phy_init(pep);
-
- update_hash_table_mac_address(pep, NULL, dev->dev_addr);
-
- return 0;
-}
-
static int pxa168_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct pxa168_eth_private *pep = netdev_priv(dev);
--
2.1.1
From: Antoine Ténart <[email protected]>
Internal FastEthernet PHY on BG2Q is connected via MII, add a
corresponding phy-connection-type property to the Ethernet node.
Tested-by: Antoine Ténart <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
Changelog:
v1->v2:
- add phy-connection-type to controller node instead of PHY node
(Reported by Sergei Shtylyov)
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
arch/arm/boot/dts/berlin2q.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi
index 891d56b03922..6bd01add3984 100644
--- a/arch/arm/boot/dts/berlin2q.dtsi
+++ b/arch/arm/boot/dts/berlin2q.dtsi
@@ -123,6 +123,7 @@
local-mac-address = [00 00 00 00 00 00];
#address-cells = <1>;
#size-cells = <0>;
+ phy-connection-type = "mii";
phy-handle = <ðphy0>;
status = "disabled";
--
2.1.1
Current libphy handling in pxa168_eth lacks proper phy_connect. Prepare
to fix this by first moving phy properties from platform_data to private
driver data.
Tested-by: Antoine Ténart <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
Changelog:
v1->v2:
- get phy-connection-type from controller node instead of PHY node
(Reported by Sergei Shtylyov)
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
drivers/net/ethernet/marvell/pxa168_eth.c | 38 +++++++++++++++++++------------
1 file changed, 23 insertions(+), 15 deletions(-)
diff --git a/drivers/net/ethernet/marvell/pxa168_eth.c b/drivers/net/ethernet/marvell/pxa168_eth.c
index c3b209cd0660..3918887e09c5 100644
--- a/drivers/net/ethernet/marvell/pxa168_eth.c
+++ b/drivers/net/ethernet/marvell/pxa168_eth.c
@@ -197,6 +197,9 @@ struct tx_desc {
struct pxa168_eth_private {
int port_num; /* User Ethernet port number */
int phy_addr;
+ int phy_speed;
+ int phy_duplex;
+ phy_interface_t phy_intf;
int rx_resource_err; /* Rx ring resource error flag */
@@ -1394,19 +1397,17 @@ static void phy_init(struct pxa168_eth_private *pep)
{
struct phy_device *phy = pep->phy;
- phy_attach(pep->dev, dev_name(&phy->dev), PHY_INTERFACE_MODE_MII);
+ phy_attach(pep->dev, dev_name(&phy->dev), pep->phy_intf);
- if (pep->pd && pep->pd->speed != 0) {
+ phy->speed = pep->phy_speed;
+ phy->duplex = pep->phy_duplex;
+ phy->autoneg = AUTONEG_ENABLE;
+ phy->supported &= PHY_BASIC_FEATURES;
+ phy->advertising = phy->supported | ADVERTISED_Autoneg;
+
+ if (pep->phy_speed != 0) {
phy->autoneg = AUTONEG_DISABLE;
phy->advertising = 0;
- phy->speed = pep->pd->speed;
- phy->duplex = pep->pd->duplex;
- } else {
- phy->autoneg = AUTONEG_ENABLE;
- phy->speed = 0;
- phy->duplex = 0;
- phy->supported &= PHY_BASIC_FEATURES;
- phy->advertising = phy->supported | ADVERTISED_Autoneg;
}
phy_start_aneg(phy);
@@ -1416,9 +1417,6 @@ static int ethernet_phy_setup(struct net_device *dev)
{
struct pxa168_eth_private *pep = netdev_priv(dev);
- if (pep->pd && pep->pd->init)
- pep->pd->init();
-
pep->phy = phy_scan(pep, pep->phy_addr & 0x1f);
if (pep->phy != NULL)
phy_init(pep);
@@ -1552,13 +1550,23 @@ static int pxa168_eth_probe(struct platform_device *pdev)
pep->port_num = pep->pd->port_number;
pep->phy_addr = pep->pd->phy_addr;
+ pep->phy_speed = pep->pd->speed;
+ pep->phy_duplex = pep->pd->duplex;
+ pep->phy_intf = pep->pd->intf;
+
+ if (pep->pd->init)
+ pep->pd->init();
} else if (pdev->dev.of_node) {
of_property_read_u32(pdev->dev.of_node, "port-id",
&pep->port_num);
np = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0);
- if (np)
- of_property_read_u32(np, "reg", &pep->phy_addr);
+ if (!np) {
+ dev_err(&pdev->dev, "missing phy-handle\n");
+ return -EINVAL;
+ }
+ of_property_read_u32(np, "reg", &pep->phy_addr);
+ pep->phy_intf = of_get_phy_mode(pdev->dev.of_node);
}
/* Hardware supports only 3 ports */
--
2.1.1
The PXA168 Ethernet IP support MII and RMII connection to its PHY.
Currently, pxa168 platform_data does not provide a way to pass that
and there is one user of pxa168 platform_data (mach-mmp/gplug).
Given the pinctrl settings of gplug it uses RMII, so add and pass
a corresponding phy_interface_t.
Tested-by: Antoine Ténart <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
arch/arm/mach-mmp/gplugd.c | 2 ++
include/linux/pxa168_eth.h | 1 +
2 files changed, 3 insertions(+)
diff --git a/arch/arm/mach-mmp/gplugd.c b/arch/arm/mach-mmp/gplugd.c
index d81b2475e67e..3b5794cd0357 100644
--- a/arch/arm/mach-mmp/gplugd.c
+++ b/arch/arm/mach-mmp/gplugd.c
@@ -12,6 +12,7 @@
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/gpio-pxa.h>
+#include <linux/phy.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
@@ -158,6 +159,7 @@ struct pxa168_eth_platform_data gplugd_eth_platform_data = {
.port_number = 0,
.phy_addr = 0,
.speed = 0, /* Autonagotiation */
+ .intf = PHY_INTERFACE_MODE_RMII,
.init = gplugd_eth_init,
};
diff --git a/include/linux/pxa168_eth.h b/include/linux/pxa168_eth.h
index 18d75e795606..37c381120bc8 100644
--- a/include/linux/pxa168_eth.h
+++ b/include/linux/pxa168_eth.h
@@ -13,6 +13,7 @@ struct pxa168_eth_platform_data {
*/
int speed; /* 0, SPEED_10, SPEED_100 */
int duplex; /* DUPLEX_HALF or DUPLEX_FULL */
+ phy_interface_t intf;
/*
* Override default RX/TX queue sizes if nonzero.
--
2.1.1
Marvell BG2 has two fast ethernet controllers with internal PHY,
add the corresponding nodes to SoC dtsi.
Tested-by: Antoine Ténart <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
Changelog:
v1->v2:
- move phy-connection-type to controller node instead of PHY node
(Reported by Sergei Shtylyov)
Cc: "David S. Miller" <[email protected]>
Cc: "Antoine Ténart" <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
arch/arm/boot/dts/berlin2.dtsi | 36 ++++++++++++++++++++++++++++++++++++
1 file changed, 36 insertions(+)
diff --git a/arch/arm/boot/dts/berlin2.dtsi b/arch/arm/boot/dts/berlin2.dtsi
index 9d7c810ebd0b..dc0227dfc691 100644
--- a/arch/arm/boot/dts/berlin2.dtsi
+++ b/arch/arm/boot/dts/berlin2.dtsi
@@ -79,11 +79,47 @@
clocks = <&chip CLKID_TWD>;
};
+ eth1: ethernet@b90000 {
+ compatible = "marvell,pxa168-eth";
+ reg = <0xb90000 0x10000>;
+ clocks = <&chip CLKID_GETH1>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ /* set by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy-connection-type = "mii";
+ phy-handle = <ðphy1>;
+ status = "disabled";
+
+ ethphy1: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+
cpu-ctrl@dd0000 {
compatible = "marvell,berlin-cpu-ctrl";
reg = <0xdd0000 0x10000>;
};
+ eth0: ethernet@e50000 {
+ compatible = "marvell,pxa168-eth";
+ reg = <0xe50000 0x10000>;
+ clocks = <&chip CLKID_GETH0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ /* set by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy-connection-type = "mii";
+ phy-handle = <ðphy0>;
+ status = "disabled";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+
apb@e80000 {
compatible = "simple-bus";
#address-cells = <1>;
--
2.1.1
From: Sebastian Hesselbarth <[email protected]>
Date: Wed, 22 Oct 2014 20:26:43 +0200
> This patch series deals with a removing a IP feature that can be found
> on all currently supported Marvell Ethernet IP (pxa168_eth, mv643xx_eth,
> mvneta). The MAC IP allows to automatically perform PHY auto-negotiation
> without software interaction.
>
> However, this feature (a) fundamentally clashes with the way libphy works
> and (b) is unable to deal with quirky PHYs that require special treatment.
> In this series, pxa168_eth driver is rewritten to completely disable that
> feature and properly deal with libphy provided PHYs.
>
> As usual, a branch on top of v3.18-rc1 can be found at
>
> git://git.infradead.org/users/hesselba/linux-berlin.git devel/bg2-bg2cd-eth-v2
>
> Patches 1-5 should go through David's net tree, I'll pick up the DT patches
> 6-9.
Patches 1-5 applied to net-next, thanks.
Do not add phy include to the board file but platform_data include
instead.
Signed-off-by: Sebastian Hesselbarth <[email protected]>
---
David,
I should have compile tested this patch earlier. I did now on
pxa168_defconfig right after I received an 0-day kbuild error
on this patch.
This is the corresponding fix, can you please squash it in?
Thanks and sorry for the noise,
Sebastian
Cc: "David S. Miller" <[email protected]>
Cc: Antoine Tenart <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Eric Miao <[email protected]>
Cc: Haojian Zhuang <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
arch/arm/mach-mmp/gplugd.c | 1 -
include/linux/pxa168_eth.h | 2 ++
2 files changed, 2 insertions(+), 1 deletion(-)
diff --git a/arch/arm/mach-mmp/gplugd.c b/arch/arm/mach-mmp/gplugd.c
index 3b5794cd0357..22762a1f9f72 100644
--- a/arch/arm/mach-mmp/gplugd.c
+++ b/arch/arm/mach-mmp/gplugd.c
@@ -12,7 +12,6 @@
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/gpio-pxa.h>
-#include <linux/phy.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
diff --git a/include/linux/pxa168_eth.h b/include/linux/pxa168_eth.h
index 37c381120bc8..e1ab6e86cdb3 100644
--- a/include/linux/pxa168_eth.h
+++ b/include/linux/pxa168_eth.h
@@ -4,6 +4,8 @@
#ifndef __LINUX_PXA168_ETH_H
#define __LINUX_PXA168_ETH_H
+#include <linux/phy.h>
+
struct pxa168_eth_platform_data {
int port_number;
int phy_addr;
--
1.9.1
From: Sebastian Hesselbarth <[email protected]>
Date: Sat, 25 Oct 2014 12:08:59 +0200
> Do not add phy include to the board file but platform_data include
> instead.
>
> Signed-off-by: Sebastian Hesselbarth <[email protected]>
> ---
> David,
>
> I should have compile tested this patch earlier. I did now on
> pxa168_defconfig right after I received an 0-day kbuild error
> on this patch.
>
> This is the corresponding fix, can you please squash it in?
>
> Thanks and sorry for the noise,
Patch applied to net-next, but:
1) There is never any way for me to "squash" a patch into an old
one. Once I apply a patch it is a permanent commit in my tree
and cannot be undone and/or modified.
Therefore the only thing you can do is send me a relative fix
and that's what shows up in my tree as yet another later commit.
2) Always be specific about the target tree in you subject,
line. Never assume I can figure it out by context.
Thanks.
On 28.10.2014 21:49, David Miller wrote:
> From: Sebastian Hesselbarth <[email protected]>
> Date: Sat, 25 Oct 2014 12:08:59 +0200
>
>> Do not add phy include to the board file but platform_data include
>> instead.
>>
>> Signed-off-by: Sebastian Hesselbarth <[email protected]>
>> ---
>> David,
>>
>> I should have compile tested this patch earlier. I did now on
>> pxa168_defconfig right after I received an 0-day kbuild error
>> on this patch.
>>
>> This is the corresponding fix, can you please squash it in?
>>
>> Thanks and sorry for the noise,
>
> Patch applied to net-next, but:
>
> 1) There is never any way for me to "squash" a patch into an old
> one. Once I apply a patch it is a permanent commit in my tree
> and cannot be undone and/or modified.
>
> Therefore the only thing you can do is send me a relative fix
> and that's what shows up in my tree as yet another later commit.
Ok, good to know and sorry for the crippled fixup patch. I was assuming
that net-next is also rebased until pulled/moved to some stable state.
> 2) Always be specific about the target tree in you subject,
> line. Never assume I can figure it out by context.
Also, sorry for the little information given.
Thanks,
Sebastian
On 22.10.2014 20:26, Sebastian Hesselbarth wrote:
> Marvell BG2 has two fast ethernet controllers with internal PHY,
> add the corresponding nodes to SoC dtsi.
>
> Tested-by: Antoine Ténart <[email protected]>
> Reviewed-by: Florian Fainelli <[email protected]>
> Signed-off-by: Sebastian Hesselbarth <[email protected]>
Applied the four DT patches to berlin/dt.
Sebastian
> ---
> Changelog:
> v1->v2:
> - move phy-connection-type to controller node instead of PHY node
> (Reported by Sergei Shtylyov)
>
> Cc: "David S. Miller" <[email protected]>
> Cc: "Antoine Ténart" <[email protected]>
> Cc: Florian Fainelli <[email protected]>
> Cc: Eric Miao <[email protected]>
> Cc: Haojian Zhuang <[email protected]>
> Cc: [email protected]
> Cc: [email protected]
> Cc: [email protected]
> Cc: [email protected]
> ---
> arch/arm/boot/dts/berlin2.dtsi | 36 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 36 insertions(+)
>
> diff --git a/arch/arm/boot/dts/berlin2.dtsi b/arch/arm/boot/dts/berlin2.dtsi
> index 9d7c810ebd0b..dc0227dfc691 100644
> --- a/arch/arm/boot/dts/berlin2.dtsi
> +++ b/arch/arm/boot/dts/berlin2.dtsi
> @@ -79,11 +79,47 @@
> clocks = <&chip CLKID_TWD>;
> };
>
> + eth1: ethernet@b90000 {
> + compatible = "marvell,pxa168-eth";
> + reg = <0xb90000 0x10000>;
> + clocks = <&chip CLKID_GETH1>;
> + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> + /* set by bootloader */
> + local-mac-address = [00 00 00 00 00 00];
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy-connection-type = "mii";
> + phy-handle = <ðphy1>;
> + status = "disabled";
> +
> + ethphy1: ethernet-phy@0 {
> + reg = <0>;
> + };
> + };
> +
> cpu-ctrl@dd0000 {
> compatible = "marvell,berlin-cpu-ctrl";
> reg = <0xdd0000 0x10000>;
> };
>
> + eth0: ethernet@e50000 {
> + compatible = "marvell,pxa168-eth";
> + reg = <0xe50000 0x10000>;
> + clocks = <&chip CLKID_GETH0>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + /* set by bootloader */
> + local-mac-address = [00 00 00 00 00 00];
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy-connection-type = "mii";
> + phy-handle = <ðphy0>;
> + status = "disabled";
> +
> + ethphy0: ethernet-phy@0 {
> + reg = <0>;
> + };
> + };
> +
> apb@e80000 {
> compatible = "simple-bus";
> #address-cells = <1>;
>