Hi,
This is the forth version of this driver. V3 could be found here [1].
Changes since v3.
- Addressed review comments from Hartmut Knaack and Mark Rutland:
Better description of 'reg' property.
Add # to address-cells and size-cells DT document.
Dropped interrupt-names property, it was not actually used by driver.
DT header file, which contain channels names definitions, is part of
documentation patch now.
Clarified 'qcom,decimation' property. Hopefully it make sense now.
Make more explicit that all reference channels configuration nodes have
to be defined in DT.
- Promote dev_dbg to dev_err in error paths. Stan, I hope you are ok with this :-)
- Use 32 bit calculations in calibration routine.
- Read ADC result with one regmap call.
- Show status and state registers if ADC conversin fails. Errors should not
normally happen, so I will like to see content of this registers in such cases.
- Use new struct iio_info::of_xlate for channel number translation.
- Removed device wakeup initialization code, which didn't make sense to me
for such kind of device.
Patches depend on "iio: inkern: Add of_xlate function to struct iio_info" patch,
which is included in IIO testing branch [2].
[1] http://comments.gmane.org/gmane.linux.ports.arm.msm/9741
[2] http://git.kernel.org/cgit/linux/kernel/git/jic23/iio.git/log/?h=testing
Stanimir Varbanov (2):
DT: iio: vadc: document dt binding
iio: vadc: Qualcomm SPMI PMIC voltage ADC driver
.../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 129 +++
drivers/iio/adc/Kconfig | 14 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/qcom-spmi-vadc.c | 1015 ++++++++++++++++++++
include/dt-bindings/iio/qcom,spmi-vadc.h | 119 +++
5 files changed, 1278 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
create mode 100644 drivers/iio/adc/qcom-spmi-vadc.c
create mode 100644 include/dt-bindings/iio/qcom,spmi-vadc.h
--
1.9.1
From: Stanimir Varbanov <[email protected]>
Document DT binding for Qualcomm SPMI PMIC voltage ADC
driver.
Signed-off-by: Stanimir Varbanov <[email protected]>
Signed-off-by: Ivan T. Ivanov <[email protected]>
---
.../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 129 +++++++++++++++++++++
include/dt-bindings/iio/qcom,spmi-vadc.h | 119 +++++++++++++++++++
2 files changed, 248 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
create mode 100644 include/dt-bindings/iio/qcom,spmi-vadc.h
diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
new file mode 100644
index 0000000..2253813
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
@@ -0,0 +1,129 @@
+Qualcomm's SPMI PMIC voltage ADC
+
+SPMI PMIC voltage ADC (VADC) provides interface to clients to read
+voltage. The VADC is a 15-bit sigma-delta ADC.
+
+VADC node:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,spmi-vadc".
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: VADC base address and length in the SPMI PMIC register map.
+
+- #address-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Must be one. Child node 'reg' property should define ADC
+ channel number.
+
+- #size-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Must be zero.
+
+- #io-channel-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Must be one. For details about IIO bindings see:
+ Documentation/devicetree/bindings/iio/iio-bindings.txt
+
+- interrupts:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: End of conversion interrupt.
+
+Channel node properties:
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: ADC channel number.
+ See include/dt-bindings/iio/qcom,spmi-vadc.h
+
+- qcom,decimation:
+ Usage: optional
+ Value type: <u32>
+ Definition: This parameters is used to decrease ADC sampling rate.
+ Quicker measurements can be made by reducing decimation ratio.
+ Valid values are 512, 1024, 2048, 4096.
+ If property is not found, default value of 512 will be used.
+
+- qcom,pre-scaling:
+ Usage: optional
+ Value type: <u32 array>
+ Definition: Used for scaling the channel input signal before the signal is
+ fed to VADC. The configuration for this node is to know the
+ pre-determined ratio and use it for post scaling. Select one from
+ the following options.
+ <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
+ If property is not found default value depending of chip will be used.
+
+- qcom,ratiometric:
+ Usage: optional
+ Value type: <empty>
+ Definition: Channel calibration type. If this property is specified
+ VADC will use the VDD reference (1.8V) and GND for channel
+ calibration. If property is not found, channel will be
+ calibrated with 0.625V and 1.25V reference channels, also
+ known as absolute calibration.
+
+- qcom,hw-settle-time:
+ Usage: optional
+ Value type: <u32>
+ Definition: Time between AMUX getting configured and the ADC starting
+ conversion. Delay = 100us * (value) for value < 11, and
+ 2ms * (value - 10) otherwise.
+ Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800,
+ 900 us and 1, 2, 4, 6, 8, 10 ms
+ If property is not found, channel will use 0us.
+
+- qcom,avg-samples:
+ Usage: optional
+ Value type: <u32>
+ Definition: Number of samples to be used for measurement.
+ Averaging provides the option to obtain a single measurement
+ from the ADC that is an average of multiple samples. The value
+ selected is 2^(value).
+ Valid values are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
+ If property is not found, 1 sample will be used.
+
+NOTE:
+
+Following channels, also know as reference points channels, are used for
+result calibration and their channel configuration nodes should be defined:
+VADC_REF_625MV and/or VADC_SPARE1, based on PMIC version, VADC_REF_1250MV,
+VADC_GND_REF and VADC_VDD_VADC.
+
+Example:
+
+ /* VADC node */
+ pmic_vadc: vadc@3100 {
+ compatible = "qcom,spmi-vadc";
+ reg = <0x3100 0x100>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+
+ /* Channel node */
+ usb_id_nopull {
+ reg = <VADC_LR_MUX10_USB_ID>;
+ qcom,decimation = <512>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,avg-samples = <1>;
+ qcom,pre-scaling = <1 3>;
+ };
+ };
+
+ /* IIO client node */
+ usb {
+ io-channels = <&pmic_vadc VADC_LR_MUX10_USB_ID>;
+ io-channel-names = "vadc";
+ };
diff --git a/include/dt-bindings/iio/qcom,spmi-vadc.h b/include/dt-bindings/iio/qcom,spmi-vadc.h
new file mode 100644
index 0000000..42121fa
--- /dev/null
+++ b/include/dt-bindings/iio/qcom,spmi-vadc.h
@@ -0,0 +1,119 @@
+/*
+ * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_QCOM_SPMI_VADC_H
+#define _DT_BINDINGS_QCOM_SPMI_VADC_H
+
+/* Voltage ADC channels */
+#define VADC_USBIN 0x00
+#define VADC_DCIN 0x01
+#define VADC_VCHG_SNS 0x02
+#define VADC_SPARE1_03 0x03
+#define VADC_USB_ID_MV 0x04
+#define VADC_VCOIN 0x05
+#define VADC_VBAT_SNS 0x06
+#define VADC_VSYS 0x07
+#define VADC_DIE_TEMP 0x08
+#define VADC_REF_625MV 0x09
+#define VADC_REF_1250MV 0x0a
+#define VADC_CHG_TEMP 0x0b
+#define VADC_SPARE1 0x0c
+#define VADC_SPARE2 0x0d
+#define VADC_GND_REF 0x0e
+#define VADC_VDD_VADC 0x0f
+
+#define VADC_P_MUX1_1_1 0x10
+#define VADC_P_MUX2_1_1 0x11
+#define VADC_P_MUX3_1_1 0x12
+#define VADC_P_MUX4_1_1 0x13
+#define VADC_P_MUX5_1_1 0x14
+#define VADC_P_MUX6_1_1 0x15
+#define VADC_P_MUX7_1_1 0x16
+#define VADC_P_MUX8_1_1 0x17
+#define VADC_P_MUX9_1_1 0x18
+#define VADC_P_MUX10_1_1 0x19
+#define VADC_P_MUX11_1_1 0x1a
+#define VADC_P_MUX12_1_1 0x1b
+#define VADC_P_MUX13_1_1 0x1c
+#define VADC_P_MUX14_1_1 0x1d
+#define VADC_P_MUX15_1_1 0x1e
+#define VADC_P_MUX16_1_1 0x1f
+
+#define VADC_P_MUX1_1_3 0x20
+#define VADC_P_MUX2_1_3 0x21
+#define VADC_P_MUX3_1_3 0x22
+#define VADC_P_MUX4_1_3 0x23
+#define VADC_P_MUX5_1_3 0x24
+#define VADC_P_MUX6_1_3 0x25
+#define VADC_P_MUX7_1_3 0x26
+#define VADC_P_MUX8_1_3 0x27
+#define VADC_P_MUX9_1_3 0x28
+#define VADC_P_MUX10_1_3 0x29
+#define VADC_P_MUX11_1_3 0x2a
+#define VADC_P_MUX12_1_3 0x2b
+#define VADC_P_MUX13_1_3 0x2c
+#define VADC_P_MUX14_1_3 0x2d
+#define VADC_P_MUX15_1_3 0x2e
+#define VADC_P_MUX16_1_3 0x2f
+
+#define VADC_LR_MUX1_BAT_THERM 0x30
+#define VADC_LR_MUX2_BAT_ID 0x31
+#define VADC_LR_MUX3_XO_THERM 0x32
+#define VADC_LR_MUX4_AMUX_THM1 0x33
+#define VADC_LR_MUX5_AMUX_THM2 0x34
+#define VADC_LR_MUX6_AMUX_THM3 0x35
+#define VADC_LR_MUX7_HW_ID 0x36
+#define VADC_LR_MUX8_AMUX_THM4 0x37
+#define VADC_LR_MUX9_AMUX_THM5 0x38
+#define VADC_LR_MUX10_USB_ID 0x39
+#define VADC_AMUX_PU1 0x3a
+#define VADC_AMUX_PU2 0x3b
+#define VADC_LR_MUX3_BUF_XO_THERM 0x3c
+
+#define VADC_LR_MUX1_PU1_BAT_THERM 0x70
+#define VADC_LR_MUX2_PU1_BAT_ID 0x71
+#define VADC_LR_MUX3_PU1_XO_THERM 0x72
+#define VADC_LR_MUX4_PU1_AMUX_THM1 0x73
+#define VADC_LR_MUX5_PU1_AMUX_THM2 0x74
+#define VADC_LR_MUX6_PU1_AMUX_THM3 0x75
+#define VADC_LR_MUX7_PU1_AMUX_HW_ID 0x76
+#define VADC_LR_MUX8_PU1_AMUX_THM4 0x77
+#define VADC_LR_MUX9_PU1_AMUX_THM5 0x78
+#define VADC_LR_MUX10_PU1_AMUX_USB_ID 0x79
+#define VADC_LR_MUX3_BUF_PU1_XO_THERM 0x7c
+
+#define VADC_LR_MUX1_PU2_BAT_THERM 0xb0
+#define VADC_LR_MUX2_PU2_BAT_ID 0xb1
+#define VADC_LR_MUX3_PU2_XO_THERM 0xb2
+#define VADC_LR_MUX4_PU2_AMUX_THM1 0xb3
+#define VADC_LR_MUX5_PU2_AMUX_THM2 0xb4
+#define VADC_LR_MUX6_PU2_AMUX_THM3 0xb5
+#define VADC_LR_MUX7_PU2_AMUX_HW_ID 0xb6
+#define VADC_LR_MUX8_PU2_AMUX_THM4 0xb7
+#define VADC_LR_MUX9_PU2_AMUX_THM5 0xb8
+#define VADC_LR_MUX10_PU2_AMUX_USB_ID 0xb9
+#define VADC_LR_MUX3_BUF_PU2_XO_THERM 0xbc
+
+#define VADC_LR_MUX1_PU1_PU2_BAT_THERM 0xf0
+#define VADC_LR_MUX2_PU1_PU2_BAT_ID 0xf1
+#define VADC_LR_MUX3_PU1_PU2_XO_THERM 0xf2
+#define VADC_LR_MUX4_PU1_PU2_AMUX_THM1 0xf3
+#define VADC_LR_MUX5_PU1_PU2_AMUX_THM2 0xf4
+#define VADC_LR_MUX6_PU1_PU2_AMUX_THM3 0xf5
+#define VADC_LR_MUX7_PU1_PU2_AMUX_HW_ID 0xf6
+#define VADC_LR_MUX8_PU1_PU2_AMUX_THM4 0xf7
+#define VADC_LR_MUX9_PU1_PU2_AMUX_THM5 0xf8
+#define VADC_LR_MUX10_PU1_PU2_AMUX_USB_ID 0xf9
+#define VADC_LR_MUX3_BUF_PU1_PU2_XO_THERM 0xfc
+
+#endif /* _DT_BINDINGS_QCOM_SPMI_VADC_H */
--
1.9.1
From: Stanimir Varbanov <[email protected]>
The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
15 bits resolution and register space inside PMIC accessible across
SPMI bus.
The vadc driver registers itself through IIO interface.
Signed-off-by: Stanimir Varbanov <[email protected]>
Signed-off-by: Ivan T. Ivanov <[email protected]>
---
drivers/iio/adc/Kconfig | 14 +
drivers/iio/adc/Makefile | 1 +
drivers/iio/adc/qcom-spmi-vadc.c | 1015 ++++++++++++++++++++++++++++++++++++++
3 files changed, 1030 insertions(+)
create mode 100644 drivers/iio/adc/qcom-spmi-vadc.c
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 88bdc8f..af6e10b 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -206,6 +206,20 @@ config NAU7802
To compile this driver as a module, choose M here: the
module will be called nau7802.
+config QCOM_SPMI_VADC
+ tristate "Qualcomm SPMI PMIC voltage ADC"
+ depends on SPMI
+ select REGMAP_SPMI
+ help
+ This is the IIO Voltage ADC driver for Qualcomm QPNP VADC Chip.
+
+ The driver supports multiple channels read. The VADC is a 15-bit
+ sigma-delta ADC. Some of the channels are internally used for
+ calibration.
+
+ To compile this driver as a module, choose M here: the module will
+ be called qcom-spmi-vadc.
+
config ROCKCHIP_SARADC
tristate "Rockchip SARADC driver"
depends on ARCH_ROCKCHIP || (ARM && COMPILE_TEST)
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index cb88a6a..479b457 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_MCP320X) += mcp320x.o
obj-$(CONFIG_MCP3422) += mcp3422.o
obj-$(CONFIG_MEN_Z188_ADC) += men_z188_adc.o
obj-$(CONFIG_NAU7802) += nau7802.o
+obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o
obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o
obj-$(CONFIG_TI_ADC081C) += ti-adc081c.o
obj-$(CONFIG_TI_ADC128S052) += ti-adc128s052.o
diff --git a/drivers/iio/adc/qcom-spmi-vadc.c b/drivers/iio/adc/qcom-spmi-vadc.c
new file mode 100644
index 0000000..6e6881c
--- /dev/null
+++ b/drivers/iio/adc/qcom-spmi-vadc.c
@@ -0,0 +1,1015 @@
+/*
+ * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/bitops.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/log2.h>
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+/* VADC register and bit definitions */
+#define VADC_REVISION2 0x1
+#define VADC_REVISION2_SUPPORTED_VADC 1
+
+#define VADC_PERPH_TYPE 0x4
+#define VADC_PERPH_TYPE_ADC 8
+
+#define VADC_PERPH_SUBTYPE 0x5
+#define VADC_PERPH_SUBTYPE_VADC 1
+
+#define VADC_STATUS1 0x8
+#define VADC_STATUS1_OP_MODE 4
+#define VADC_STATUS1_REQ_STS BIT(1)
+#define VADC_STATUS1_EOC BIT(0)
+#define VADC_STATUS1_REQ_STS_EOC_MASK 0x3
+
+#define VADC_MODE_CTL 0x40
+#define VADC_OP_MODE_SHIFT 3
+#define VADC_OP_MODE_NORMAL 0
+#define VADC_AMUX_TRIM_EN BIT(1)
+#define VADC_ADC_TRIM_EN BIT(0)
+
+#define VADC_EN_CTL1 0x46
+#define VADC_EN_CTL1_SET BIT(7)
+
+#define VADC_ADC_CH_SEL_CTL 0x48
+
+#define VADC_ADC_DIG_PARAM 0x50
+#define VADC_ADC_DIG_DEC_RATIO_SEL_SHIFT 2
+
+#define VADC_HW_SETTLE_DELAY 0x51
+
+#define VADC_CONV_REQ 0x52
+#define VADC_CONV_REQ_SET BIT(7)
+
+#define VADC_FAST_AVG_CTL 0x5a
+#define VADC_FAST_AVG_EN 0x5b
+#define VADC_FAST_AVG_EN_SET BIT(7)
+
+#define VADC_ACCESS 0xd0
+#define VADC_ACCESS_DATA 0xa5
+
+#define VADC_PERH_RESET_CTL3 0xda
+#define VADC_FOLLOW_WARM_RB BIT(2)
+
+#define VADC_DATA 0x60 /* 16 bits */
+
+#define VADC_CONV_TIME_MIN_US 2000
+#define VADC_CONV_TIME_MAX_US 2100
+
+/* Min ADC code represents 0V */
+#define VADC_MIN_ADC_CODE 0x6000
+/* Max ADC code represents full-scale range of 1.8V */
+#define VADC_MAX_ADC_CODE 0xa800
+
+#define VADC_ABSOLUTE_RANGE_UV 625000
+#define VADC_RATIOMETRIC_RANGE_UV 1800000
+
+#define VADC_DEF_PRESCALING 0 /* 1:1 */
+#define VADC_DEF_DECIMATION 0 /* 512 */
+#define VADC_DEF_HW_SETTLE_TIME 0 /* 0 us */
+#define VADC_DEF_AVG_SAMPLES 0 /* 1 sample */
+#define VADC_DEF_CALIB_TYPE VADC_CALIB_ABSOLUTE
+
+#define VADC_DECIMATION_MIN 512
+#define VADC_DECIMATION_MAX 4096
+
+#define VADC_HW_SETTLE_DELAY_MAX 10000
+#define VADC_AVG_SAMPLES_MAX 512
+
+#define KELVINMIL_CELSIUSMIL 273150
+
+#define VADC_CHAN_MIN VADC_USBIN
+#define VADC_CHAN_MAX VADC_LR_MUX3_BUF_PU1_PU2_XO_THERM
+
+/*
+ * VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
+ * VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
+ * calibration.
+ */
+enum vadc_calibration {
+ VADC_CALIB_ABSOLUTE = 0,
+ VADC_CALIB_RATIOMETRIC
+};
+
+/**
+ * struct vadc_linear_graph - Represent ADC characteristics.
+ * @dy: numerator slope to calculate the gain.
+ * @dx: denominator slope to calculate the gain.
+ * @vref: A/D word of the voltage reference used for the channel.
+ * @gnd: A/D word of the ground reference used for the channel.
+ *
+ * Each ADC device has different offset and gain parameters which are
+ * computed to calibrate the device.
+ */
+struct vadc_linear_graph {
+ s32 dy;
+ s32 dx;
+ s32 vref;
+ s32 gnd;
+};
+
+/**
+ * struct vadc_prescale_ratio - Represent scaling ratio for ADC input.
+ * @num: the inverse numerator of the gain applied to the input channel.
+ * @den: the inverse denominator of the gain applied to the input channel.
+ */
+struct vadc_prescale_ratio {
+ u32 num;
+ u32 den;
+};
+
+/**
+ * struct vadc_channel_prop - VADC channel property.
+ * @channel: channel number, refer to the channel list.
+ * @calibration: calibration type.
+ * @decimation: sampling rate supported for the channel.
+ * @prescale: channel scaling performed on the input signal.
+ * @hw_settle_time: the time between AMUX being configured and the
+ * start of conversion.
+ * @avg_samples: ability to provide single result from the ADC
+ * that is an average of multiple measurements.
+ */
+struct vadc_channel_prop {
+ unsigned int channel;
+ enum vadc_calibration calibration;
+ unsigned int decimation;
+ unsigned int prescale;
+ unsigned int hw_settle_time;
+ unsigned int avg_samples;
+};
+
+/**
+ * struct vadc_priv - VADC private structure.
+ * @regmap: pointer to struct regmap.
+ * @dev: pointer to struct device.
+ * @base: base address for the ADC peripheral.
+ * @nchannels: number of VADC channels.
+ * @chan_props: array of VADC channel properties.
+ * @iio_chans: array of IIO channels specification.
+ * @are_ref_measured: are reference points measured.
+ * @poll_eoc: use polling instead of interrupt.
+ * @complete: VADC result notification after interrupt is received.
+ * @graph: store parameters for calibration.
+ */
+struct vadc_priv {
+ struct regmap *regmap;
+ struct device *dev;
+ u16 base;
+ unsigned int nchannels;
+ struct vadc_channel_prop *chan_props;
+ struct iio_chan_spec *iio_chans;
+ bool are_ref_measured;
+ bool poll_eoc;
+ struct completion complete;
+ struct vadc_linear_graph graph[2];
+};
+
+static const struct vadc_prescale_ratio vadc_prescale_ratios[] = {
+ {.num = 1, .den = 1},
+ {.num = 1, .den = 3},
+ {.num = 1, .den = 4},
+ {.num = 1, .den = 6},
+ {.num = 1, .den = 20},
+ {.num = 1, .den = 8},
+ {.num = 10, .den = 81},
+ {.num = 1, .den = 10}
+};
+
+static int vadc_read(struct vadc_priv *vadc, u16 offset, u8 *data)
+{
+ return regmap_bulk_read(vadc->regmap, vadc->base + offset, data, 1);
+}
+
+static int vadc_write(struct vadc_priv *vadc, u16 offset, u8 data)
+{
+ return regmap_write(vadc->regmap, vadc->base + offset, data);
+}
+
+static int vadc_reset(struct vadc_priv *vadc)
+{
+ u8 data;
+ int ret;
+
+ ret = vadc_write(vadc, VADC_ACCESS, VADC_ACCESS_DATA);
+ if (ret)
+ return ret;
+
+ ret = vadc_read(vadc, VADC_PERH_RESET_CTL3, &data);
+ if (ret)
+ return ret;
+
+ ret = vadc_write(vadc, VADC_ACCESS, VADC_ACCESS_DATA);
+ if (ret)
+ return ret;
+
+ data |= VADC_FOLLOW_WARM_RB;
+
+ return vadc_write(vadc, VADC_PERH_RESET_CTL3, data);
+}
+
+static int vadc_set_state(struct vadc_priv *vadc, bool state)
+{
+ return vadc_write(vadc, VADC_EN_CTL1, state ? VADC_EN_CTL1_SET : 0);
+}
+
+static void vadc_show_status(struct vadc_priv *vadc)
+{
+ u8 mode, sta1, chan, dig, en, req;
+ int ret;
+
+ ret = vadc_read(vadc, VADC_MODE_CTL, &mode);
+ if (ret)
+ return;
+
+ ret = vadc_read(vadc, VADC_ADC_DIG_PARAM, &dig);
+ if (ret)
+ return;
+
+ ret = vadc_read(vadc, VADC_ADC_CH_SEL_CTL, &chan);
+ if (ret)
+ return;
+
+ ret = vadc_read(vadc, VADC_CONV_REQ, &req);
+ if (ret)
+ return;
+
+ ret = vadc_read(vadc, VADC_STATUS1, &sta1);
+ if (ret)
+ return;
+
+ ret = vadc_read(vadc, VADC_EN_CTL1, &en);
+ if (ret)
+ return;
+
+ dev_err(vadc->dev,
+ "mode:%02x en:%02x chan:%02x dig:%02x req:%02x sta1:%02x\n",
+ mode, en, chan, dig, req, sta1);
+}
+
+static int vadc_configure(struct vadc_priv *vadc,
+ struct vadc_channel_prop *prop)
+{
+ u8 decimation, mode_ctrl;
+ int ret;
+
+ /* Mode selection */
+ mode_ctrl = (VADC_OP_MODE_NORMAL << VADC_OP_MODE_SHIFT) |
+ VADC_ADC_TRIM_EN | VADC_AMUX_TRIM_EN;
+ ret = vadc_write(vadc, VADC_MODE_CTL, mode_ctrl);
+ if (ret)
+ return ret;
+
+ /* Channel selection */
+ ret = vadc_write(vadc, VADC_ADC_CH_SEL_CTL, prop->channel);
+ if (ret)
+ return ret;
+
+ /* Digital parameter setup */
+ decimation = prop->decimation << VADC_ADC_DIG_DEC_RATIO_SEL_SHIFT;
+ ret = vadc_write(vadc, VADC_ADC_DIG_PARAM, decimation);
+ if (ret)
+ return ret;
+
+ /* HW settle time delay */
+ ret = vadc_write(vadc, VADC_HW_SETTLE_DELAY, prop->hw_settle_time);
+ if (ret)
+ return ret;
+
+ ret = vadc_write(vadc, VADC_FAST_AVG_CTL, prop->avg_samples);
+ if (ret)
+ return ret;
+
+ if (prop->avg_samples)
+ ret = vadc_write(vadc, VADC_FAST_AVG_EN, VADC_FAST_AVG_EN_SET);
+ else
+ ret = vadc_write(vadc, VADC_FAST_AVG_EN, 0);
+
+ return ret;
+}
+
+static int vadc_poll_wait_eoc(struct vadc_priv *vadc, unsigned int interval_us)
+{
+ unsigned int count, retry;
+ u8 sta1;
+ int ret;
+
+ retry = interval_us / VADC_CONV_TIME_MIN_US;
+
+ for (count = 0; count < retry; count++) {
+ ret = vadc_read(vadc, VADC_STATUS1, &sta1);
+ if (ret)
+ return ret;
+
+ sta1 &= VADC_STATUS1_REQ_STS_EOC_MASK;
+ if (sta1 == VADC_STATUS1_EOC)
+ return 0;
+
+ usleep_range(VADC_CONV_TIME_MIN_US, VADC_CONV_TIME_MAX_US);
+ }
+
+ vadc_show_status(vadc);
+
+ return -ETIMEDOUT;
+}
+
+static int vadc_read_result(struct vadc_priv *vadc, u16 *data)
+{
+ int ret;
+
+ ret = regmap_bulk_read(vadc->regmap, vadc->base + VADC_DATA, data, 2);
+ if (ret)
+ return ret;
+
+ *data = clamp_t(u16, *data, VADC_MIN_ADC_CODE, VADC_MAX_ADC_CODE);
+ return 0;
+}
+
+static struct vadc_channel_prop *vadc_get_channel(struct vadc_priv *vadc,
+ unsigned int num)
+{
+ unsigned int i;
+
+ for (i = 0; i < vadc->nchannels; i++)
+ if (vadc->chan_props[i].channel == num)
+ return &vadc->chan_props[i];
+
+ dev_dbg(vadc->dev, "no such channel %02x\n", num);
+
+ return NULL;
+}
+
+static int vadc_do_conversion(struct vadc_priv *vadc,
+ struct vadc_channel_prop *prop, u16 *data)
+{
+ unsigned int timeout;
+ int ret;
+
+ ret = vadc_configure(vadc, prop);
+ if (ret)
+ return ret;
+
+ if (!vadc->poll_eoc)
+ reinit_completion(&vadc->complete);
+
+ ret = vadc_set_state(vadc, true);
+ if (ret)
+ return ret;
+
+ ret = vadc_write(vadc, VADC_CONV_REQ, VADC_CONV_REQ_SET);
+ if (ret)
+ goto err_disable;
+
+ timeout = BIT(prop->avg_samples) * VADC_CONV_TIME_MIN_US * 2;
+
+ if (vadc->poll_eoc) {
+ ret = vadc_poll_wait_eoc(vadc, timeout);
+ } else {
+ ret = wait_for_completion_timeout(&vadc->complete, timeout);
+ if (!ret) {
+ ret = -ETIMEDOUT;
+ goto err_disable;
+ }
+
+ /* Double check conversion status */
+ ret = vadc_poll_wait_eoc(vadc, VADC_CONV_TIME_MIN_US);
+ if (ret)
+ goto err_disable;
+ }
+
+ ret = vadc_read_result(vadc, data);
+
+err_disable:
+ vadc_set_state(vadc, false);
+ if (ret)
+ dev_err(vadc->dev, "conversion failed\n");
+
+ return ret;
+}
+
+static int vadc_measure_ref_points(struct vadc_priv *vadc)
+{
+ struct vadc_channel_prop *prop;
+ u16 read_1, read_2;
+ int ret;
+
+ vadc->graph[VADC_CALIB_RATIOMETRIC].dx = VADC_RATIOMETRIC_RANGE_UV;
+ vadc->graph[VADC_CALIB_ABSOLUTE].dx = VADC_ABSOLUTE_RANGE_UV;
+
+ prop = vadc_get_channel(vadc, VADC_REF_1250MV);
+ ret = vadc_do_conversion(vadc, prop, &read_1);
+ if (ret)
+ goto err;
+
+ /* Try with buffered 625mV channel first */
+ prop = vadc_get_channel(vadc, VADC_SPARE1);
+ if (!prop)
+ prop = vadc_get_channel(vadc, VADC_REF_625MV);
+
+ ret = vadc_do_conversion(vadc, prop, &read_2);
+ if (ret)
+ goto err;
+
+ if (read_1 == read_2) {
+ ret = -EINVAL;
+ goto err;
+ }
+
+ vadc->graph[VADC_CALIB_ABSOLUTE].dy = read_1 - read_2;
+ vadc->graph[VADC_CALIB_ABSOLUTE].vref = read_1;
+ vadc->graph[VADC_CALIB_ABSOLUTE].gnd = read_2;
+
+ /* Ratiometric calibration */
+ prop = vadc_get_channel(vadc, VADC_VDD_VADC);
+ ret = vadc_do_conversion(vadc, prop, &read_1);
+ if (ret)
+ goto err;
+
+ prop = vadc_get_channel(vadc, VADC_GND_REF);
+ ret = vadc_do_conversion(vadc, prop, &read_2);
+ if (ret)
+ goto err;
+
+ if (read_1 == read_2) {
+ ret = -EINVAL;
+ goto err;
+ }
+
+ vadc->graph[VADC_CALIB_RATIOMETRIC].dy = read_1 - read_2;
+ vadc->graph[VADC_CALIB_RATIOMETRIC].vref = read_1;
+ vadc->graph[VADC_CALIB_RATIOMETRIC].gnd = read_2;
+err:
+ if (ret)
+ dev_err(vadc->dev, "measure reference points failed\n");
+
+ return ret;
+}
+
+static s32 vadc_calibrate(struct vadc_priv *vadc,
+ const struct vadc_channel_prop *prop, u16 adc_code)
+{
+ const struct vadc_prescale_ratio *prescale;
+ s32 voltage;
+
+ voltage = adc_code - vadc->graph[prop->calibration].gnd;
+ voltage *= vadc->graph[prop->calibration].dx;
+ voltage = voltage / vadc->graph[prop->calibration].dy;
+
+ if (prop->calibration == VADC_CALIB_ABSOLUTE)
+ voltage += vadc->graph[prop->calibration].dx;
+
+ if (voltage < 0)
+ voltage = 0;
+
+ prescale = &vadc_prescale_ratios[prop->prescale];
+
+ voltage = voltage * prescale->den;
+
+ return voltage / prescale->num;
+}
+
+static int vadc_decimation_from_dt(u32 value)
+{
+ if (!is_power_of_2(value) || value < VADC_DECIMATION_MIN ||
+ value > VADC_DECIMATION_MAX)
+ return -EINVAL;
+
+ return __ffs64(value / VADC_DECIMATION_MIN);
+}
+
+static int vadc_prescaling_from_dt(u32 num, u32 den)
+{
+ unsigned int pre;
+
+ for (pre = 0; pre < ARRAY_SIZE(vadc_prescale_ratios); pre++)
+ if (vadc_prescale_ratios[pre].num == num &&
+ vadc_prescale_ratios[pre].den == den)
+ break;
+
+ if (pre == ARRAY_SIZE(vadc_prescale_ratios))
+ return -EINVAL;
+
+ return pre;
+}
+
+static int vadc_hw_settle_time_from_dt(u32 value)
+{
+ if ((value <= 1000 && value % 100) || (value > 1000 && value % 2000))
+ return -EINVAL;
+
+ if (value <= 1000)
+ value /= 100;
+ else
+ value = value / 2000 + 10;
+
+ return value;
+}
+
+static int vadc_avg_samples_from_dt(u32 value)
+{
+ if (!is_power_of_2(value) || value > VADC_AVG_SAMPLES_MAX)
+ return -EINVAL;
+
+ return __ffs64(value);
+}
+
+static int vadc_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan, int *val, int *val2,
+ long mask)
+{
+ struct vadc_priv *vadc = iio_priv(indio_dev);
+ struct vadc_channel_prop *prop;
+ u16 adc_code;
+ int ret;
+
+ if (!vadc->are_ref_measured) {
+ ret = vadc_measure_ref_points(vadc);
+ if (ret)
+ return ret;
+
+ vadc->are_ref_measured = true;
+ }
+
+ if (mask == IIO_CHAN_INFO_PROCESSED || mask == IIO_CHAN_INFO_RAW) {
+ prop = &vadc->chan_props[chan->address];
+ ret = vadc_do_conversion(vadc, prop, &adc_code);
+ if (ret)
+ return ret;
+
+ *val = vadc_calibrate(vadc, prop, adc_code);
+ }
+
+ switch (mask) {
+ case IIO_CHAN_INFO_PROCESSED:
+ if (chan->type != IIO_TEMP && chan->channel != VADC_DIE_TEMP)
+ return -EINVAL;
+
+ /* 2mV/K, return milli Celsius */
+ *val /= 2;
+ *val -= KELVINMIL_CELSIUSMIL;
+ return IIO_VAL_INT;
+ case IIO_CHAN_INFO_RAW:
+ return IIO_VAL_INT;
+ case IIO_CHAN_INFO_SCALE:
+ *val = 0;
+ *val2 = 1000;
+ return IIO_VAL_INT_PLUS_MICRO;
+ default:
+ break;
+ }
+
+ return -EINVAL;
+}
+
+static int vadc_of_xlate(struct iio_dev *indio_dev,
+ const struct of_phandle_args *iiospec)
+{
+ struct vadc_priv *vadc = iio_priv(indio_dev);
+ unsigned int i;
+
+ for (i = 0; i < vadc->nchannels; i++)
+ if (vadc->iio_chans[i].channel == iiospec->args[0])
+ return i;
+
+ return -EINVAL;
+}
+
+static const struct iio_info vadc_info = {
+ .read_raw = vadc_read_raw,
+ .of_xlate = vadc_of_xlate,
+ .driver_module = THIS_MODULE,
+};
+
+struct vadc_channels {
+ const char *datasheet_name;
+ unsigned int prescale_index;
+ enum iio_chan_type type;
+ long info_mask;
+};
+
+#define VADC_CHAN(_dname, _type, _mask, _pre) \
+ [VADC_##_dname] = { \
+ .datasheet_name = __stringify(_dname), \
+ .prescale_index = _pre, \
+ .type = _type, \
+ .info_mask = _mask \
+ }, \
+
+#define VADC_CHAN_TEMP(_dname, _pre) \
+ VADC_CHAN(_dname, IIO_TEMP, BIT(IIO_CHAN_INFO_PROCESSED), _pre) \
+
+#define VADC_CHAN_VOLT(_dname, _pre) \
+ VADC_CHAN(_dname, IIO_VOLTAGE, \
+ BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), \
+ _pre) \
+
+/*
+ * The array represents all possible ADC channels found in the supported PMICs.
+ * Every index in the array is equal to the channel number per datasheet. The
+ * gaps in the array should be treated as reserved channels.
+ */
+static const struct vadc_channels vadc_chans[] = {
+ VADC_CHAN_VOLT(USBIN, 4)
+ VADC_CHAN_VOLT(DCIN, 4)
+ VADC_CHAN_VOLT(VCHG_SNS, 3)
+ VADC_CHAN_VOLT(SPARE1_03, 1)
+ VADC_CHAN_VOLT(USB_ID_MV, 1)
+ VADC_CHAN_VOLT(VCOIN, 1)
+ VADC_CHAN_VOLT(VBAT_SNS, 1)
+ VADC_CHAN_VOLT(VSYS, 1)
+ VADC_CHAN_TEMP(DIE_TEMP, 0)
+ VADC_CHAN_VOLT(REF_625MV, 0)
+ VADC_CHAN_VOLT(REF_1250MV, 0)
+ VADC_CHAN_VOLT(CHG_TEMP, 0)
+ VADC_CHAN_VOLT(SPARE1, 0)
+ VADC_CHAN_VOLT(SPARE2, 0)
+ VADC_CHAN_VOLT(GND_REF, 0)
+ VADC_CHAN_VOLT(VDD_VADC, 0)
+
+ VADC_CHAN_VOLT(P_MUX1_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX2_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX3_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX4_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX5_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX6_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX7_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX8_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX9_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX10_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX11_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX12_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX13_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX14_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX15_1_1, 0)
+ VADC_CHAN_VOLT(P_MUX16_1_1, 0)
+
+ VADC_CHAN_VOLT(P_MUX1_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX2_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX3_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX4_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX5_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX6_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX7_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX8_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX9_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX10_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX11_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX12_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX13_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX14_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX15_1_3, 1)
+ VADC_CHAN_VOLT(P_MUX16_1_3, 1)
+
+ VADC_CHAN_VOLT(LR_MUX1_BAT_THERM, 0)
+ VADC_CHAN_VOLT(LR_MUX2_BAT_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX3_XO_THERM, 0)
+ VADC_CHAN_VOLT(LR_MUX4_AMUX_THM1, 0)
+ VADC_CHAN_VOLT(LR_MUX5_AMUX_THM2, 0)
+ VADC_CHAN_VOLT(LR_MUX6_AMUX_THM3, 0)
+ VADC_CHAN_VOLT(LR_MUX7_HW_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX8_AMUX_THM4, 0)
+ VADC_CHAN_VOLT(LR_MUX9_AMUX_THM5, 0)
+ VADC_CHAN_VOLT(LR_MUX10_USB_ID, 0)
+ VADC_CHAN_VOLT(AMUX_PU1, 0)
+ VADC_CHAN_VOLT(AMUX_PU2, 0)
+ VADC_CHAN_VOLT(LR_MUX3_BUF_XO_THERM, 0)
+
+ VADC_CHAN_VOLT(LR_MUX1_PU1_BAT_THERM, 0)
+ VADC_CHAN_VOLT(LR_MUX2_PU1_BAT_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX3_PU1_XO_THERM, 0)
+ VADC_CHAN_VOLT(LR_MUX4_PU1_AMUX_THM1, 0)
+ VADC_CHAN_VOLT(LR_MUX5_PU1_AMUX_THM2, 0)
+ VADC_CHAN_VOLT(LR_MUX6_PU1_AMUX_THM3, 0)
+ VADC_CHAN_VOLT(LR_MUX7_PU1_AMUX_HW_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX8_PU1_AMUX_THM4, 0)
+ VADC_CHAN_VOLT(LR_MUX9_PU1_AMUX_THM5, 0)
+ VADC_CHAN_VOLT(LR_MUX10_PU1_AMUX_USB_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX3_BUF_PU1_XO_THERM, 0)
+
+ VADC_CHAN_VOLT(LR_MUX1_PU2_BAT_THERM, 0)
+ VADC_CHAN_VOLT(LR_MUX2_PU2_BAT_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX3_PU2_XO_THERM, 0)
+ VADC_CHAN_VOLT(LR_MUX4_PU2_AMUX_THM1, 0)
+ VADC_CHAN_VOLT(LR_MUX5_PU2_AMUX_THM2, 0)
+ VADC_CHAN_VOLT(LR_MUX6_PU2_AMUX_THM3, 0)
+ VADC_CHAN_VOLT(LR_MUX7_PU2_AMUX_HW_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX8_PU2_AMUX_THM4, 0)
+ VADC_CHAN_VOLT(LR_MUX9_PU2_AMUX_THM5, 0)
+ VADC_CHAN_VOLT(LR_MUX10_PU2_AMUX_USB_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX3_BUF_PU2_XO_THERM, 0)
+
+ VADC_CHAN_VOLT(LR_MUX1_PU1_PU2_BAT_THERM, 0)
+ VADC_CHAN_VOLT(LR_MUX2_PU1_PU2_BAT_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX3_PU1_PU2_XO_THERM, 0)
+ VADC_CHAN_VOLT(LR_MUX4_PU1_PU2_AMUX_THM1, 0)
+ VADC_CHAN_VOLT(LR_MUX5_PU1_PU2_AMUX_THM2, 0)
+ VADC_CHAN_VOLT(LR_MUX6_PU1_PU2_AMUX_THM3, 0)
+ VADC_CHAN_VOLT(LR_MUX7_PU1_PU2_AMUX_HW_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX8_PU1_PU2_AMUX_THM4, 0)
+ VADC_CHAN_VOLT(LR_MUX9_PU1_PU2_AMUX_THM5, 0)
+ VADC_CHAN_VOLT(LR_MUX10_PU1_PU2_AMUX_USB_ID, 0)
+ VADC_CHAN_VOLT(LR_MUX3_BUF_PU1_PU2_XO_THERM, 0)
+};
+
+static int vadc_get_dt_channel_data(struct device *dev,
+ struct vadc_channel_prop *prop,
+ struct device_node *node)
+{
+ const char *name = node->name;
+ u32 chan, value, varr[2];
+ int ret;
+
+ ret = of_property_read_u32(node, "reg", &chan);
+ if (ret) {
+ dev_err(dev, "invalid channel number %s\n", name);
+ return ret;
+ }
+
+ if (chan > VADC_CHAN_MAX || chan < VADC_CHAN_MIN) {
+ dev_err(dev, "%s invalid channel number %d\n", name, chan);
+ return -EINVAL;
+ }
+
+ /* the channel has DT description */
+ prop->channel = chan;
+
+ ret = of_property_read_u32(node, "qcom,decimation", &value);
+ if (!ret) {
+ ret = vadc_decimation_from_dt(value);
+ if (ret < 0) {
+ dev_err(dev, "%02x invalid decimation %d\n",
+ chan, value);
+ return ret;
+ }
+ prop->decimation = ret;
+ } else {
+ prop->decimation = VADC_DEF_DECIMATION;
+ }
+
+ ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2);
+ if (!ret) {
+ ret = vadc_prescaling_from_dt(varr[0], varr[1]);
+ if (ret < 0) {
+ dev_err(dev, "%02x invalid pre-scaling <%d %d>\n",
+ chan, varr[0], varr[1]);
+ return ret;
+ }
+ prop->prescale = ret;
+ } else {
+ prop->prescale = vadc_chans[prop->channel].prescale_index;
+ }
+
+ ret = of_property_read_u32(node, "qcom,hw-settle-time", &value);
+ if (!ret) {
+ ret = vadc_hw_settle_time_from_dt(value);
+ if (ret < 0) {
+ dev_err(dev, "%02x invalid hw-settle-time %d us\n",
+ chan, value);
+ return ret;
+ }
+ prop->hw_settle_time = ret;
+ } else {
+ prop->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
+ }
+
+ ret = of_property_read_u32(node, "qcom,avg-samples", &value);
+ if (!ret) {
+ ret = vadc_avg_samples_from_dt(value);
+ if (ret < 0) {
+ dev_err(dev, "%02x invalid avg-samples %d\n",
+ chan, value);
+ return ret;
+ }
+ prop->avg_samples = ret;
+ } else {
+ prop->avg_samples = VADC_DEF_AVG_SAMPLES;
+ }
+
+ if (of_property_read_bool(node, "qcom,ratiometric"))
+ prop->calibration = VADC_CALIB_RATIOMETRIC;
+ else
+ prop->calibration = VADC_CALIB_ABSOLUTE;
+
+ dev_dbg(dev, "%02x name %s\n", chan, name);
+
+ return 0;
+}
+
+static int vadc_get_dt_data(struct vadc_priv *vadc, struct device_node *node)
+{
+ const struct vadc_channels *vadc_chan;
+ struct iio_chan_spec *iio_chan;
+ struct vadc_channel_prop prop;
+ struct device_node *child;
+ unsigned int index = 0;
+ int ret;
+
+ vadc->nchannels = of_get_available_child_count(node);
+ if (!vadc->nchannels)
+ return -EINVAL;
+
+ vadc->iio_chans = devm_kcalloc(vadc->dev, vadc->nchannels,
+ sizeof(*vadc->iio_chans), GFP_KERNEL);
+ if (!vadc->iio_chans)
+ return -ENOMEM;
+
+ vadc->chan_props = devm_kcalloc(vadc->dev, vadc->nchannels,
+ sizeof(*vadc->chan_props), GFP_KERNEL);
+ if (!vadc->chan_props)
+ return -ENOMEM;
+
+ iio_chan = vadc->iio_chans;
+
+ for_each_available_child_of_node(node, child) {
+ ret = vadc_get_dt_channel_data(vadc->dev, &prop, child);
+ if (ret)
+ return ret;
+
+ vadc->chan_props[index] = prop;
+
+ vadc_chan = &vadc_chans[prop.channel];
+
+ iio_chan->channel = prop.channel;
+ iio_chan->datasheet_name = vadc_chan->datasheet_name;
+ iio_chan->info_mask_separate = vadc_chan->info_mask;
+ iio_chan->type = vadc_chan->type;
+ iio_chan->indexed = 1;
+ iio_chan->address = index++;
+
+ iio_chan++;
+ }
+
+ /* These channels are mandatory, they are used as reference points */
+ if (!vadc_get_channel(vadc, VADC_REF_1250MV)) {
+ dev_err(vadc->dev, "Please define 1.25V channel\n");
+ return -ENODEV;
+ }
+
+ if (!vadc_get_channel(vadc, VADC_REF_625MV)) {
+ dev_err(vadc->dev, "Please define 0.625V channel\n");
+ return -ENODEV;
+ }
+
+ if (!vadc_get_channel(vadc, VADC_VDD_VADC)) {
+ dev_err(vadc->dev, "Please define VDD channel\n");
+ return -ENODEV;
+ }
+
+ if (!vadc_get_channel(vadc, VADC_GND_REF)) {
+ dev_err(vadc->dev, "Please define GND channel\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static irqreturn_t vadc_isr(int irq, void *dev_id)
+{
+ struct vadc_priv *vadc = dev_id;
+
+ complete(&vadc->complete);
+
+ return IRQ_HANDLED;
+}
+
+static int vadc_check_revision(struct vadc_priv *vadc)
+{
+ u8 val;
+ int ret;
+
+ ret = vadc_read(vadc, VADC_PERPH_TYPE, &val);
+ if (ret)
+ return ret;
+
+ if (val < VADC_PERPH_TYPE_ADC) {
+ dev_err(vadc->dev, "%d is not ADC\n", val);
+ return -ENODEV;
+ }
+
+ ret = vadc_read(vadc, VADC_PERPH_SUBTYPE, &val);
+ if (ret)
+ return ret;
+
+ if (val < VADC_PERPH_SUBTYPE_VADC) {
+ dev_err(vadc->dev, "%d is not VADC\n", val);
+ return -ENODEV;
+ }
+
+ ret = vadc_read(vadc, VADC_REVISION2, &val);
+ if (ret)
+ return ret;
+
+ if (val < VADC_REVISION2_SUPPORTED_VADC) {
+ dev_err(vadc->dev, "revision %d not supported\n", val);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int vadc_probe(struct platform_device *pdev)
+{
+ struct device_node *node = pdev->dev.of_node;
+ struct device *dev = &pdev->dev;
+ struct iio_dev *indio_dev;
+ struct vadc_priv *vadc;
+ struct regmap *regmap;
+ int ret, irq_eoc;
+ u32 res;
+
+ regmap = dev_get_regmap(dev->parent, NULL);
+ if (!regmap)
+ return -ENODEV;
+
+ ret = of_property_read_u32(node, "reg", &res);
+ if (ret < 0)
+ return -ENODEV;
+
+ indio_dev = devm_iio_device_alloc(dev, sizeof(*vadc));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ vadc = iio_priv(indio_dev);
+ vadc->regmap = regmap;
+ vadc->dev = dev;
+ vadc->base = res;
+ vadc->are_ref_measured = false;
+ init_completion(&vadc->complete);
+
+ ret = vadc_check_revision(vadc);
+ if (ret)
+ return ret;
+
+ ret = vadc_get_dt_data(vadc, node);
+ if (ret)
+ return ret;
+
+ irq_eoc = platform_get_irq(pdev, 0);
+ if (irq_eoc < 0) {
+ if (irq_eoc == -EPROBE_DEFER || irq_eoc == -EINVAL)
+ return irq_eoc;
+ vadc->poll_eoc = true;
+ } else {
+ ret = devm_request_irq(dev, irq_eoc, vadc_isr, 0,
+ "spmi-vadc", vadc);
+ if (ret)
+ return ret;
+ }
+
+ ret = vadc_reset(vadc);
+ if (ret) {
+ dev_err(dev, "reset failed\n");
+ return ret;
+ }
+
+ indio_dev->dev.parent = dev;
+ indio_dev->dev.of_node = node;
+ indio_dev->name = pdev->name;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ indio_dev->info = &vadc_info;
+ indio_dev->channels = vadc->iio_chans;
+ indio_dev->num_channels = vadc->nchannels;
+
+ return devm_iio_device_register(dev, indio_dev);
+}
+
+static const struct of_device_id vadc_match_table[] = {
+ { .compatible = "qcom,spmi-vadc" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, vadc_match_table);
+
+static struct platform_driver vadc_driver = {
+ .driver = {
+ .name = "qcom-spmi-vadc",
+ .of_match_table = vadc_match_table,
+ },
+ .probe = vadc_probe,
+};
+module_platform_driver(vadc_driver);
+
+MODULE_ALIAS("platform:qcom-spmi-vadc");
+MODULE_DESCRIPTION("Qualcomm SPMI PMIC voltage ADC driver");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Stanimir Varbanov <[email protected]>");
+MODULE_AUTHOR("Ivan T. Ivanov <[email protected]>");
--
1.9.1
Ivan T. Ivanov schrieb am 03.11.2014 16:24:
> From: Stanimir Varbanov <[email protected]>
>
> Document DT binding for Qualcomm SPMI PMIC voltage ADC
> driver.
>
> Signed-off-by: Stanimir Varbanov <[email protected]>
> Signed-off-by: Ivan T. Ivanov <[email protected]>
> ---
> .../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 129 +++++++++++++++++++++
> include/dt-bindings/iio/qcom,spmi-vadc.h | 119 +++++++++++++++++++
> 2 files changed, 248 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> create mode 100644 include/dt-bindings/iio/qcom,spmi-vadc.h
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> new file mode 100644
> index 0000000..2253813
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
> @@ -0,0 +1,129 @@
> +Qualcomm's SPMI PMIC voltage ADC
> +
> +SPMI PMIC voltage ADC (VADC) provides interface to clients to read
> +voltage. The VADC is a 15-bit sigma-delta ADC.
> +
> +VADC node:
> +
> +- compatible:
> + Usage: required
> + Value type: <string>
> + Definition: Should contain "qcom,spmi-vadc".
> +
> +- reg:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: VADC base address and length in the SPMI PMIC register map.
> +
> +- #address-cells:
> + Usage: required
> + Value type: <u32>
> + Definition: Must be one. Child node 'reg' property should define ADC
> + channel number.
> +
> +- #size-cells:
> + Usage: required
> + Value type: <u32>
> + Definition: Must be zero.
> +
> +- #io-channel-cells:
> + Usage: required
> + Value type: <u32>
> + Definition: Must be one. For details about IIO bindings see:
> + Documentation/devicetree/bindings/iio/iio-bindings.txt
> +
> +- interrupts:
> + Usage: optional
> + Value type: <prop-encoded-array>
> + Definition: End of conversion interrupt.
> +
> +Channel node properties:
> +
> +- reg:
> + Usage: required
> + Value type: <u32>
> + Definition: ADC channel number.
> + See include/dt-bindings/iio/qcom,spmi-vadc.h
> +
> +- qcom,decimation:
> + Usage: optional
> + Value type: <u32>
> + Definition: This parameters is used to decrease ADC sampling rate.
Typo: This parameter (singular)
> + Quicker measurements can be made by reducing decimation ratio.
> + Valid values are 512, 1024, 2048, 4096.
> + If property is not found, default value of 512 will be used.
> +
> +- qcom,pre-scaling:
> + Usage: optional
> + Value type: <u32 array>
> + Definition: Used for scaling the channel input signal before the signal is
> + fed to VADC. The configuration for this node is to know the
> + pre-determined ratio and use it for post scaling. Select one from
> + the following options.
> + <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
> + If property is not found default value depending of chip will be used.
> +
> +- qcom,ratiometric:
> + Usage: optional
> + Value type: <empty>
> + Definition: Channel calibration type. If this property is specified
> + VADC will use the VDD reference (1.8V) and GND for channel
> + calibration. If property is not found, channel will be
> + calibrated with 0.625V and 1.25V reference channels, also
> + known as absolute calibration.
> +
> +- qcom,hw-settle-time:
> + Usage: optional
> + Value type: <u32>
> + Definition: Time between AMUX getting configured and the ADC starting
> + conversion. Delay = 100us * (value) for value < 11, and
> + 2ms * (value - 10) otherwise.
> + Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800,
> + 900 us and 1, 2, 4, 6, 8, 10 ms
> + If property is not found, channel will use 0us.
> +
> +- qcom,avg-samples:
> + Usage: optional
> + Value type: <u32>
> + Definition: Number of samples to be used for measurement.
> + Averaging provides the option to obtain a single measurement
> + from the ADC that is an average of multiple samples. The value
> + selected is 2^(value).
> + Valid values are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
> + If property is not found, 1 sample will be used.
> +
> +NOTE:
> +
> +Following channels, also know as reference points channels, are used for
Typos: <...> also known as reference point channels <...>
> +result calibration and their channel configuration nodes should be defined:
> +VADC_REF_625MV and/or VADC_SPARE1, based on PMIC version, VADC_REF_1250MV,
Better put the "based on PMIC version" into parenthesis.
> +VADC_GND_REF and VADC_VDD_VADC.
> +
> +Example:
> +
> + /* VADC node */
> + pmic_vadc: vadc@3100 {
> + compatible = "qcom,spmi-vadc";
> + reg = <0x3100 0x100>;
> + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #io-channel-cells = <1>;
> + io-channel-ranges;
> +
> + /* Channel node */
> + usb_id_nopull {
> + reg = <VADC_LR_MUX10_USB_ID>;
> + qcom,decimation = <512>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,avg-samples = <1>;
> + qcom,pre-scaling = <1 3>;
> + };
> + };
> +
> + /* IIO client node */
> + usb {
> + io-channels = <&pmic_vadc VADC_LR_MUX10_USB_ID>;
> + io-channel-names = "vadc";
> + };
> diff --git a/include/dt-bindings/iio/qcom,spmi-vadc.h b/include/dt-bindings/iio/qcom,spmi-vadc.h
> new file mode 100644
> index 0000000..42121fa
> --- /dev/null
> +++ b/include/dt-bindings/iio/qcom,spmi-vadc.h
> @@ -0,0 +1,119 @@
> +/*
> + * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef _DT_BINDINGS_QCOM_SPMI_VADC_H
> +#define _DT_BINDINGS_QCOM_SPMI_VADC_H
> +
> +/* Voltage ADC channels */
> +#define VADC_USBIN 0x00
> +#define VADC_DCIN 0x01
> +#define VADC_VCHG_SNS 0x02
> +#define VADC_SPARE1_03 0x03
> +#define VADC_USB_ID_MV 0x04
> +#define VADC_VCOIN 0x05
> +#define VADC_VBAT_SNS 0x06
> +#define VADC_VSYS 0x07
> +#define VADC_DIE_TEMP 0x08
> +#define VADC_REF_625MV 0x09
> +#define VADC_REF_1250MV 0x0a
> +#define VADC_CHG_TEMP 0x0b
> +#define VADC_SPARE1 0x0c
> +#define VADC_SPARE2 0x0d
> +#define VADC_GND_REF 0x0e
> +#define VADC_VDD_VADC 0x0f
> +
> +#define VADC_P_MUX1_1_1 0x10
> +#define VADC_P_MUX2_1_1 0x11
> +#define VADC_P_MUX3_1_1 0x12
> +#define VADC_P_MUX4_1_1 0x13
> +#define VADC_P_MUX5_1_1 0x14
> +#define VADC_P_MUX6_1_1 0x15
> +#define VADC_P_MUX7_1_1 0x16
> +#define VADC_P_MUX8_1_1 0x17
> +#define VADC_P_MUX9_1_1 0x18
> +#define VADC_P_MUX10_1_1 0x19
> +#define VADC_P_MUX11_1_1 0x1a
> +#define VADC_P_MUX12_1_1 0x1b
> +#define VADC_P_MUX13_1_1 0x1c
> +#define VADC_P_MUX14_1_1 0x1d
> +#define VADC_P_MUX15_1_1 0x1e
> +#define VADC_P_MUX16_1_1 0x1f
> +
> +#define VADC_P_MUX1_1_3 0x20
> +#define VADC_P_MUX2_1_3 0x21
> +#define VADC_P_MUX3_1_3 0x22
> +#define VADC_P_MUX4_1_3 0x23
> +#define VADC_P_MUX5_1_3 0x24
> +#define VADC_P_MUX6_1_3 0x25
> +#define VADC_P_MUX7_1_3 0x26
> +#define VADC_P_MUX8_1_3 0x27
> +#define VADC_P_MUX9_1_3 0x28
> +#define VADC_P_MUX10_1_3 0x29
> +#define VADC_P_MUX11_1_3 0x2a
> +#define VADC_P_MUX12_1_3 0x2b
> +#define VADC_P_MUX13_1_3 0x2c
> +#define VADC_P_MUX14_1_3 0x2d
> +#define VADC_P_MUX15_1_3 0x2e
> +#define VADC_P_MUX16_1_3 0x2f
> +
> +#define VADC_LR_MUX1_BAT_THERM 0x30
> +#define VADC_LR_MUX2_BAT_ID 0x31
> +#define VADC_LR_MUX3_XO_THERM 0x32
> +#define VADC_LR_MUX4_AMUX_THM1 0x33
> +#define VADC_LR_MUX5_AMUX_THM2 0x34
> +#define VADC_LR_MUX6_AMUX_THM3 0x35
> +#define VADC_LR_MUX7_HW_ID 0x36
> +#define VADC_LR_MUX8_AMUX_THM4 0x37
> +#define VADC_LR_MUX9_AMUX_THM5 0x38
> +#define VADC_LR_MUX10_USB_ID 0x39
> +#define VADC_AMUX_PU1 0x3a
> +#define VADC_AMUX_PU2 0x3b
> +#define VADC_LR_MUX3_BUF_XO_THERM 0x3c
> +
> +#define VADC_LR_MUX1_PU1_BAT_THERM 0x70
> +#define VADC_LR_MUX2_PU1_BAT_ID 0x71
> +#define VADC_LR_MUX3_PU1_XO_THERM 0x72
> +#define VADC_LR_MUX4_PU1_AMUX_THM1 0x73
> +#define VADC_LR_MUX5_PU1_AMUX_THM2 0x74
> +#define VADC_LR_MUX6_PU1_AMUX_THM3 0x75
> +#define VADC_LR_MUX7_PU1_AMUX_HW_ID 0x76
> +#define VADC_LR_MUX8_PU1_AMUX_THM4 0x77
> +#define VADC_LR_MUX9_PU1_AMUX_THM5 0x78
> +#define VADC_LR_MUX10_PU1_AMUX_USB_ID 0x79
> +#define VADC_LR_MUX3_BUF_PU1_XO_THERM 0x7c
> +
> +#define VADC_LR_MUX1_PU2_BAT_THERM 0xb0
> +#define VADC_LR_MUX2_PU2_BAT_ID 0xb1
> +#define VADC_LR_MUX3_PU2_XO_THERM 0xb2
> +#define VADC_LR_MUX4_PU2_AMUX_THM1 0xb3
> +#define VADC_LR_MUX5_PU2_AMUX_THM2 0xb4
> +#define VADC_LR_MUX6_PU2_AMUX_THM3 0xb5
> +#define VADC_LR_MUX7_PU2_AMUX_HW_ID 0xb6
> +#define VADC_LR_MUX8_PU2_AMUX_THM4 0xb7
> +#define VADC_LR_MUX9_PU2_AMUX_THM5 0xb8
> +#define VADC_LR_MUX10_PU2_AMUX_USB_ID 0xb9
> +#define VADC_LR_MUX3_BUF_PU2_XO_THERM 0xbc
> +
> +#define VADC_LR_MUX1_PU1_PU2_BAT_THERM 0xf0
> +#define VADC_LR_MUX2_PU1_PU2_BAT_ID 0xf1
> +#define VADC_LR_MUX3_PU1_PU2_XO_THERM 0xf2
> +#define VADC_LR_MUX4_PU1_PU2_AMUX_THM1 0xf3
> +#define VADC_LR_MUX5_PU1_PU2_AMUX_THM2 0xf4
> +#define VADC_LR_MUX6_PU1_PU2_AMUX_THM3 0xf5
> +#define VADC_LR_MUX7_PU1_PU2_AMUX_HW_ID 0xf6
> +#define VADC_LR_MUX8_PU1_PU2_AMUX_THM4 0xf7
> +#define VADC_LR_MUX9_PU1_PU2_AMUX_THM5 0xf8
> +#define VADC_LR_MUX10_PU1_PU2_AMUX_USB_ID 0xf9
> +#define VADC_LR_MUX3_BUF_PU1_PU2_XO_THERM 0xfc
> +
> +#endif /* _DT_BINDINGS_QCOM_SPMI_VADC_H */
>
On 03/11/14 15:24, Ivan T. Ivanov wrote:
> From: Stanimir Varbanov <[email protected]>
>
> The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
> 15 bits resolution and register space inside PMIC accessible across
> SPMI bus.
>
> The vadc driver registers itself through IIO interface.
>
> Signed-off-by: Stanimir Varbanov <[email protected]>
> Signed-off-by: Ivan T. Ivanov <[email protected]>
Hi Ivan,
Couple of utterly tiny bits inline. The biggest one is that
you store some info about the calibration that you never actually
use... Left over from some debugging perhaps?
Jonathan
> ---
> drivers/iio/adc/Kconfig | 14 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/qcom-spmi-vadc.c | 1015 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 1030 insertions(+)
> create mode 100644 drivers/iio/adc/qcom-spmi-vadc.c
>
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 88bdc8f..af6e10b 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -206,6 +206,20 @@ config NAU7802
> To compile this driver as a module, choose M here: the
> module will be called nau7802.
>
> +config QCOM_SPMI_VADC
> + tristate "Qualcomm SPMI PMIC voltage ADC"
> + depends on SPMI
> + select REGMAP_SPMI
> + help
> + This is the IIO Voltage ADC driver for Qualcomm QPNP VADC Chip.
> +
> + The driver supports multiple channels read. The VADC is a 15-bit
> + sigma-delta ADC. Some of the channels are internally used for
> + calibration.
> +
> + To compile this driver as a module, choose M here: the module will
> + be called qcom-spmi-vadc.
> +
> config ROCKCHIP_SARADC
> tristate "Rockchip SARADC driver"
> depends on ARCH_ROCKCHIP || (ARM && COMPILE_TEST)
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index cb88a6a..479b457 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -22,6 +22,7 @@ obj-$(CONFIG_MCP320X) += mcp320x.o
> obj-$(CONFIG_MCP3422) += mcp3422.o
> obj-$(CONFIG_MEN_Z188_ADC) += men_z188_adc.o
> obj-$(CONFIG_NAU7802) += nau7802.o
> +obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o
> obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o
> obj-$(CONFIG_TI_ADC081C) += ti-adc081c.o
> obj-$(CONFIG_TI_ADC128S052) += ti-adc128s052.o
> diff --git a/drivers/iio/adc/qcom-spmi-vadc.c b/drivers/iio/adc/qcom-spmi-vadc.c
> new file mode 100644
> index 0000000..6e6881c
> --- /dev/null
> +++ b/drivers/iio/adc/qcom-spmi-vadc.c
> @@ -0,0 +1,1015 @@
> +/*
> + * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/completion.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/iio/iio.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/log2.h>
> +
> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> +
> +/* VADC register and bit definitions */
> +#define VADC_REVISION2 0x1
> +#define VADC_REVISION2_SUPPORTED_VADC 1
> +
> +#define VADC_PERPH_TYPE 0x4
> +#define VADC_PERPH_TYPE_ADC 8
> +
> +#define VADC_PERPH_SUBTYPE 0x5
> +#define VADC_PERPH_SUBTYPE_VADC 1
> +
> +#define VADC_STATUS1 0x8
> +#define VADC_STATUS1_OP_MODE 4
> +#define VADC_STATUS1_REQ_STS BIT(1)
> +#define VADC_STATUS1_EOC BIT(0)
> +#define VADC_STATUS1_REQ_STS_EOC_MASK 0x3
> +
> +#define VADC_MODE_CTL 0x40
> +#define VADC_OP_MODE_SHIFT 3
> +#define VADC_OP_MODE_NORMAL 0
> +#define VADC_AMUX_TRIM_EN BIT(1)
> +#define VADC_ADC_TRIM_EN BIT(0)
> +
> +#define VADC_EN_CTL1 0x46
> +#define VADC_EN_CTL1_SET BIT(7)
> +
> +#define VADC_ADC_CH_SEL_CTL 0x48
> +
> +#define VADC_ADC_DIG_PARAM 0x50
> +#define VADC_ADC_DIG_DEC_RATIO_SEL_SHIFT 2
> +
> +#define VADC_HW_SETTLE_DELAY 0x51
> +
> +#define VADC_CONV_REQ 0x52
> +#define VADC_CONV_REQ_SET BIT(7)
> +
> +#define VADC_FAST_AVG_CTL 0x5a
> +#define VADC_FAST_AVG_EN 0x5b
> +#define VADC_FAST_AVG_EN_SET BIT(7)
> +
> +#define VADC_ACCESS 0xd0
> +#define VADC_ACCESS_DATA 0xa5
> +
> +#define VADC_PERH_RESET_CTL3 0xda
> +#define VADC_FOLLOW_WARM_RB BIT(2)
> +
> +#define VADC_DATA 0x60 /* 16 bits */
> +
> +#define VADC_CONV_TIME_MIN_US 2000
> +#define VADC_CONV_TIME_MAX_US 2100
> +
> +/* Min ADC code represents 0V */
> +#define VADC_MIN_ADC_CODE 0x6000
> +/* Max ADC code represents full-scale range of 1.8V */
> +#define VADC_MAX_ADC_CODE 0xa800
> +
> +#define VADC_ABSOLUTE_RANGE_UV 625000
> +#define VADC_RATIOMETRIC_RANGE_UV 1800000
> +
> +#define VADC_DEF_PRESCALING 0 /* 1:1 */
> +#define VADC_DEF_DECIMATION 0 /* 512 */
> +#define VADC_DEF_HW_SETTLE_TIME 0 /* 0 us */
> +#define VADC_DEF_AVG_SAMPLES 0 /* 1 sample */
> +#define VADC_DEF_CALIB_TYPE VADC_CALIB_ABSOLUTE
> +
> +#define VADC_DECIMATION_MIN 512
> +#define VADC_DECIMATION_MAX 4096
> +
> +#define VADC_HW_SETTLE_DELAY_MAX 10000
> +#define VADC_AVG_SAMPLES_MAX 512
> +
> +#define KELVINMIL_CELSIUSMIL 273150
> +
> +#define VADC_CHAN_MIN VADC_USBIN
> +#define VADC_CHAN_MAX VADC_LR_MUX3_BUF_PU1_PU2_XO_THERM
> +
> +/*
> + * VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
> + * VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
> + * calibration.
> + */
> +enum vadc_calibration {
> + VADC_CALIB_ABSOLUTE = 0,
> + VADC_CALIB_RATIOMETRIC
> +};
> +
> +/**
> + * struct vadc_linear_graph - Represent ADC characteristics.
> + * @dy: numerator slope to calculate the gain.
As dy is always equal to vref-gnd you could drop it and use those
directly...
Conversly you store vref or grnd and never use them...
> + * @dx: denominator slope to calculate the gain.
> + * @vref: A/D word of the voltage reference used for the channel.
> + * @gnd: A/D word of the ground reference used for the channel.
> + *
> + * Each ADC device has different offset and gain parameters which are
> + * computed to calibrate the device.
> + */
> +struct vadc_linear_graph {
> + s32 dy;
> + s32 dx;
> + s32 vref;
> + s32 gnd;
> +};
> +
> +/**
> + * struct vadc_prescale_ratio - Represent scaling ratio for ADC input.
> + * @num: the inverse numerator of the gain applied to the input channel.
> + * @den: the inverse denominator of the gain applied to the input channel.
> + */
> +struct vadc_prescale_ratio {
> + u32 num;
> + u32 den;
> +};
> +
> +/**
> + * struct vadc_channel_prop - VADC channel property.
> + * @channel: channel number, refer to the channel list.
> + * @calibration: calibration type.
> + * @decimation: sampling rate supported for the channel.
> + * @prescale: channel scaling performed on the input signal.
> + * @hw_settle_time: the time between AMUX being configured and the
> + * start of conversion.
> + * @avg_samples: ability to provide single result from the ADC
> + * that is an average of multiple measurements.
> + */
> +struct vadc_channel_prop {
> + unsigned int channel;
> + enum vadc_calibration calibration;
> + unsigned int decimation;
> + unsigned int prescale;
> + unsigned int hw_settle_time;
> + unsigned int avg_samples;
> +};
> +
> +/**
> + * struct vadc_priv - VADC private structure.
> + * @regmap: pointer to struct regmap.
> + * @dev: pointer to struct device.
> + * @base: base address for the ADC peripheral.
> + * @nchannels: number of VADC channels.
> + * @chan_props: array of VADC channel properties.
> + * @iio_chans: array of IIO channels specification.
> + * @are_ref_measured: are reference points measured.
> + * @poll_eoc: use polling instead of interrupt.
> + * @complete: VADC result notification after interrupt is received.
> + * @graph: store parameters for calibration.
> + */
> +struct vadc_priv {
> + struct regmap *regmap;
> + struct device *dev;
> + u16 base;
> + unsigned int nchannels;
> + struct vadc_channel_prop *chan_props;
> + struct iio_chan_spec *iio_chans;
> + bool are_ref_measured;
> + bool poll_eoc;
> + struct completion complete;
> + struct vadc_linear_graph graph[2];
> +};
> +
> +static const struct vadc_prescale_ratio vadc_prescale_ratios[] = {
> + {.num = 1, .den = 1},
> + {.num = 1, .den = 3},
> + {.num = 1, .den = 4},
> + {.num = 1, .den = 6},
> + {.num = 1, .den = 20},
> + {.num = 1, .den = 8},
> + {.num = 10, .den = 81},
> + {.num = 1, .den = 10}
> +};
> +
> +static int vadc_read(struct vadc_priv *vadc, u16 offset, u8 *data)
> +{
> + return regmap_bulk_read(vadc->regmap, vadc->base + offset, data, 1);
> +}
> +
> +static int vadc_write(struct vadc_priv *vadc, u16 offset, u8 data)
> +{
> + return regmap_write(vadc->regmap, vadc->base + offset, data);
> +}
> +
> +static int vadc_reset(struct vadc_priv *vadc)
> +{
> + u8 data;
> + int ret;
> +
> + ret = vadc_write(vadc, VADC_ACCESS, VADC_ACCESS_DATA);
> + if (ret)
> + return ret;
> +
> + ret = vadc_read(vadc, VADC_PERH_RESET_CTL3, &data);
> + if (ret)
> + return ret;
> +
> + ret = vadc_write(vadc, VADC_ACCESS, VADC_ACCESS_DATA);
> + if (ret)
> + return ret;
> +
> + data |= VADC_FOLLOW_WARM_RB;
> +
> + return vadc_write(vadc, VADC_PERH_RESET_CTL3, data);
> +}
> +
> +static int vadc_set_state(struct vadc_priv *vadc, bool state)
> +{
> + return vadc_write(vadc, VADC_EN_CTL1, state ? VADC_EN_CTL1_SET : 0);
> +}
> +
> +static void vadc_show_status(struct vadc_priv *vadc)
> +{
> + u8 mode, sta1, chan, dig, en, req;
> + int ret;
> +
> + ret = vadc_read(vadc, VADC_MODE_CTL, &mode);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_ADC_DIG_PARAM, &dig);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_ADC_CH_SEL_CTL, &chan);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_CONV_REQ, &req);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_STATUS1, &sta1);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_EN_CTL1, &en);
> + if (ret)
> + return;
> +
> + dev_err(vadc->dev,
> + "mode:%02x en:%02x chan:%02x dig:%02x req:%02x sta1:%02x\n",
> + mode, en, chan, dig, req, sta1);
> +}
> +
> +static int vadc_configure(struct vadc_priv *vadc,
> + struct vadc_channel_prop *prop)
> +{
> + u8 decimation, mode_ctrl;
> + int ret;
> +
> + /* Mode selection */
> + mode_ctrl = (VADC_OP_MODE_NORMAL << VADC_OP_MODE_SHIFT) |
> + VADC_ADC_TRIM_EN | VADC_AMUX_TRIM_EN;
> + ret = vadc_write(vadc, VADC_MODE_CTL, mode_ctrl);
> + if (ret)
> + return ret;
> +
> + /* Channel selection */
> + ret = vadc_write(vadc, VADC_ADC_CH_SEL_CTL, prop->channel);
> + if (ret)
> + return ret;
> +
> + /* Digital parameter setup */
> + decimation = prop->decimation << VADC_ADC_DIG_DEC_RATIO_SEL_SHIFT;
> + ret = vadc_write(vadc, VADC_ADC_DIG_PARAM, decimation);
> + if (ret)
> + return ret;
> +
> + /* HW settle time delay */
> + ret = vadc_write(vadc, VADC_HW_SETTLE_DELAY, prop->hw_settle_time);
> + if (ret)
> + return ret;
> +
> + ret = vadc_write(vadc, VADC_FAST_AVG_CTL, prop->avg_samples);
> + if (ret)
> + return ret;
> +
> + if (prop->avg_samples)
> + ret = vadc_write(vadc, VADC_FAST_AVG_EN, VADC_FAST_AVG_EN_SET);
> + else
> + ret = vadc_write(vadc, VADC_FAST_AVG_EN, 0);
> +
> + return ret;
> +}
> +
> +static int vadc_poll_wait_eoc(struct vadc_priv *vadc, unsigned int interval_us)
> +{
> + unsigned int count, retry;
> + u8 sta1;
> + int ret;
> +
> + retry = interval_us / VADC_CONV_TIME_MIN_US;
> +
> + for (count = 0; count < retry; count++) {
> + ret = vadc_read(vadc, VADC_STATUS1, &sta1);
> + if (ret)
> + return ret;
> +
> + sta1 &= VADC_STATUS1_REQ_STS_EOC_MASK;
> + if (sta1 == VADC_STATUS1_EOC)
> + return 0;
> +
> + usleep_range(VADC_CONV_TIME_MIN_US, VADC_CONV_TIME_MAX_US);
> + }
> +
> + vadc_show_status(vadc);
> +
> + return -ETIMEDOUT;
> +}
> +
> +static int vadc_read_result(struct vadc_priv *vadc, u16 *data)
> +{
> + int ret;
> +
> + ret = regmap_bulk_read(vadc->regmap, vadc->base + VADC_DATA, data, 2);
> + if (ret)
> + return ret;
> +
> + *data = clamp_t(u16, *data, VADC_MIN_ADC_CODE, VADC_MAX_ADC_CODE);
utter nitpick. A blank line here would be perfect ;)
> + return 0;
> +}
> +
> +static struct vadc_channel_prop *vadc_get_channel(struct vadc_priv *vadc,
> + unsigned int num)
> +{
> + unsigned int i;
> +
> + for (i = 0; i < vadc->nchannels; i++)
> + if (vadc->chan_props[i].channel == num)
> + return &vadc->chan_props[i];
> +
> + dev_dbg(vadc->dev, "no such channel %02x\n", num);
> +
> + return NULL;
> +}
> +
> +static int vadc_do_conversion(struct vadc_priv *vadc,
> + struct vadc_channel_prop *prop, u16 *data)
> +{
> + unsigned int timeout;
> + int ret;
> +
> + ret = vadc_configure(vadc, prop);
> + if (ret)
> + return ret;
> +
> + if (!vadc->poll_eoc)
> + reinit_completion(&vadc->complete);
> +
> + ret = vadc_set_state(vadc, true);
> + if (ret)
> + return ret;
> +
> + ret = vadc_write(vadc, VADC_CONV_REQ, VADC_CONV_REQ_SET);
> + if (ret)
> + goto err_disable;
> +
> + timeout = BIT(prop->avg_samples) * VADC_CONV_TIME_MIN_US * 2;
> +
> + if (vadc->poll_eoc) {
> + ret = vadc_poll_wait_eoc(vadc, timeout);
> + } else {
> + ret = wait_for_completion_timeout(&vadc->complete, timeout);
> + if (!ret) {
> + ret = -ETIMEDOUT;
> + goto err_disable;
> + }
> +
> + /* Double check conversion status */
> + ret = vadc_poll_wait_eoc(vadc, VADC_CONV_TIME_MIN_US);
> + if (ret)
> + goto err_disable;
> + }
> +
> + ret = vadc_read_result(vadc, data);
> +
> +err_disable:
> + vadc_set_state(vadc, false);
> + if (ret)
> + dev_err(vadc->dev, "conversion failed\n");
> +
> + return ret;
> +}
> +
> +static int vadc_measure_ref_points(struct vadc_priv *vadc)
> +{
> + struct vadc_channel_prop *prop;
> + u16 read_1, read_2;
> + int ret;
> +
> + vadc->graph[VADC_CALIB_RATIOMETRIC].dx = VADC_RATIOMETRIC_RANGE_UV;
> + vadc->graph[VADC_CALIB_ABSOLUTE].dx = VADC_ABSOLUTE_RANGE_UV;
> +
> + prop = vadc_get_channel(vadc, VADC_REF_1250MV);
> + ret = vadc_do_conversion(vadc, prop, &read_1);
> + if (ret)
> + goto err;
> +
> + /* Try with buffered 625mV channel first */
> + prop = vadc_get_channel(vadc, VADC_SPARE1);
> + if (!prop)
> + prop = vadc_get_channel(vadc, VADC_REF_625MV);
> +
> + ret = vadc_do_conversion(vadc, prop, &read_2);
> + if (ret)
> + goto err;
> +
> + if (read_1 == read_2) {
> + ret = -EINVAL;
> + goto err;
> + }
> +
> + vadc->graph[VADC_CALIB_ABSOLUTE].dy = read_1 - read_2;
> + vadc->graph[VADC_CALIB_ABSOLUTE].vref = read_1;
> + vadc->graph[VADC_CALIB_ABSOLUTE].gnd = read_2;
> +
> + /* Ratiometric calibration */
> + prop = vadc_get_channel(vadc, VADC_VDD_VADC);
> + ret = vadc_do_conversion(vadc, prop, &read_1);
> + if (ret)
> + goto err;
> +
> + prop = vadc_get_channel(vadc, VADC_GND_REF);
> + ret = vadc_do_conversion(vadc, prop, &read_2);
> + if (ret)
> + goto err;
> +
> + if (read_1 == read_2) {
> + ret = -EINVAL;
> + goto err;
> + }
> +
> + vadc->graph[VADC_CALIB_RATIOMETRIC].dy = read_1 - read_2;
> + vadc->graph[VADC_CALIB_RATIOMETRIC].vref = read_1;
> + vadc->graph[VADC_CALIB_RATIOMETRIC].gnd = read_2;
> +err:
> + if (ret)
> + dev_err(vadc->dev, "measure reference points failed\n");
> +
> + return ret;
> +}
> +
> +static s32 vadc_calibrate(struct vadc_priv *vadc,
> + const struct vadc_channel_prop *prop, u16 adc_code)
> +{
> + const struct vadc_prescale_ratio *prescale;
> + s32 voltage;
> +
> + voltage = adc_code - vadc->graph[prop->calibration].gnd;
> + voltage *= vadc->graph[prop->calibration].dx;
> + voltage = voltage / vadc->graph[prop->calibration].dy;
> +
> + if (prop->calibration == VADC_CALIB_ABSOLUTE)
> + voltage += vadc->graph[prop->calibration].dx;
> +
> + if (voltage < 0)
> + voltage = 0;
> +
> + prescale = &vadc_prescale_ratios[prop->prescale];
> +
> + voltage = voltage * prescale->den;
> +
> + return voltage / prescale->num;
> +}
> +
> +static int vadc_decimation_from_dt(u32 value)
> +{
> + if (!is_power_of_2(value) || value < VADC_DECIMATION_MIN ||
> + value > VADC_DECIMATION_MAX)
> + return -EINVAL;
> +
> + return __ffs64(value / VADC_DECIMATION_MIN);
> +}
> +
> +static int vadc_prescaling_from_dt(u32 num, u32 den)
> +{
> + unsigned int pre;
> +
> + for (pre = 0; pre < ARRAY_SIZE(vadc_prescale_ratios); pre++)
> + if (vadc_prescale_ratios[pre].num == num &&
> + vadc_prescale_ratios[pre].den == den)
> + break;
> +
> + if (pre == ARRAY_SIZE(vadc_prescale_ratios))
> + return -EINVAL;
> +
> + return pre;
> +}
> +
> +static int vadc_hw_settle_time_from_dt(u32 value)
> +{
> + if ((value <= 1000 && value % 100) || (value > 1000 && value % 2000))
> + return -EINVAL;
> +
> + if (value <= 1000)
> + value /= 100;
> + else
> + value = value / 2000 + 10;
> +
> + return value;
> +}
> +
> +static int vadc_avg_samples_from_dt(u32 value)
> +{
> + if (!is_power_of_2(value) || value > VADC_AVG_SAMPLES_MAX)
> + return -EINVAL;
> +
> + return __ffs64(value);
> +}
> +
> +static int vadc_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int *val, int *val2,
> + long mask)
> +{
> + struct vadc_priv *vadc = iio_priv(indio_dev);
> + struct vadc_channel_prop *prop;
> + u16 adc_code;
> + int ret;
> +
> + if (!vadc->are_ref_measured) {
> + ret = vadc_measure_ref_points(vadc);
> + if (ret)
> + return ret;
> +
> + vadc->are_ref_measured = true;
> + }
> +
> + if (mask == IIO_CHAN_INFO_PROCESSED || mask == IIO_CHAN_INFO_RAW) {
> + prop = &vadc->chan_props[chan->address];
> + ret = vadc_do_conversion(vadc, prop, &adc_code);
> + if (ret)
> + return ret;
> +
> + *val = vadc_calibrate(vadc, prop, adc_code);
> + }
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_PROCESSED:
> + if (chan->type != IIO_TEMP && chan->channel != VADC_DIE_TEMP)
> + return -EINVAL;
> +
> + /* 2mV/K, return milli Celsius */
> + *val /= 2;
> + *val -= KELVINMIL_CELSIUSMIL;
> + return IIO_VAL_INT;
> + case IIO_CHAN_INFO_RAW:
> + return IIO_VAL_INT;
> + case IIO_CHAN_INFO_SCALE:
> + *val = 0;
> + *val2 = 1000;
> + return IIO_VAL_INT_PLUS_MICRO;
> + default:
> + break;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int vadc_of_xlate(struct iio_dev *indio_dev,
> + const struct of_phandle_args *iiospec)
> +{
> + struct vadc_priv *vadc = iio_priv(indio_dev);
> + unsigned int i;
> +
> + for (i = 0; i < vadc->nchannels; i++)
> + if (vadc->iio_chans[i].channel == iiospec->args[0])
> + return i;
> +
> + return -EINVAL;
> +}
> +
> +static const struct iio_info vadc_info = {
> + .read_raw = vadc_read_raw,
> + .of_xlate = vadc_of_xlate,
> + .driver_module = THIS_MODULE,
> +};
> +
> +struct vadc_channels {
> + const char *datasheet_name;
> + unsigned int prescale_index;
> + enum iio_chan_type type;
> + long info_mask;
> +};
> +
> +#define VADC_CHAN(_dname, _type, _mask, _pre) \
> + [VADC_##_dname] = { \
> + .datasheet_name = __stringify(_dname), \
> + .prescale_index = _pre, \
> + .type = _type, \
> + .info_mask = _mask \
> + }, \
> +
> +#define VADC_CHAN_TEMP(_dname, _pre) \
> + VADC_CHAN(_dname, IIO_TEMP, BIT(IIO_CHAN_INFO_PROCESSED), _pre) \
> +
> +#define VADC_CHAN_VOLT(_dname, _pre) \
> + VADC_CHAN(_dname, IIO_VOLTAGE, \
> + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), \
> + _pre) \
> +
> +/*
> + * The array represents all possible ADC channels found in the supported PMICs.
> + * Every index in the array is equal to the channel number per datasheet. The
> + * gaps in the array should be treated as reserved channels.
> + */
> +static const struct vadc_channels vadc_chans[] = {
> + VADC_CHAN_VOLT(USBIN, 4)
> + VADC_CHAN_VOLT(DCIN, 4)
> + VADC_CHAN_VOLT(VCHG_SNS, 3)
> + VADC_CHAN_VOLT(SPARE1_03, 1)
> + VADC_CHAN_VOLT(USB_ID_MV, 1)
> + VADC_CHAN_VOLT(VCOIN, 1)
> + VADC_CHAN_VOLT(VBAT_SNS, 1)
> + VADC_CHAN_VOLT(VSYS, 1)
> + VADC_CHAN_TEMP(DIE_TEMP, 0)
> + VADC_CHAN_VOLT(REF_625MV, 0)
> + VADC_CHAN_VOLT(REF_1250MV, 0)
> + VADC_CHAN_VOLT(CHG_TEMP, 0)
> + VADC_CHAN_VOLT(SPARE1, 0)
> + VADC_CHAN_VOLT(SPARE2, 0)
> + VADC_CHAN_VOLT(GND_REF, 0)
> + VADC_CHAN_VOLT(VDD_VADC, 0)
> +
> + VADC_CHAN_VOLT(P_MUX1_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX2_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX3_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX4_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX5_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX6_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX7_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX8_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX9_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX10_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX11_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX12_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX13_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX14_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX15_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX16_1_1, 0)
> +
> + VADC_CHAN_VOLT(P_MUX1_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX2_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX3_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX4_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX5_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX6_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX7_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX8_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX9_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX10_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX11_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX12_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX13_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX14_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX15_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX16_1_3, 1)
> +
> + VADC_CHAN_VOLT(LR_MUX1_BAT_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX2_BAT_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_XO_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX4_AMUX_THM1, 0)
> + VADC_CHAN_VOLT(LR_MUX5_AMUX_THM2, 0)
> + VADC_CHAN_VOLT(LR_MUX6_AMUX_THM3, 0)
> + VADC_CHAN_VOLT(LR_MUX7_HW_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX8_AMUX_THM4, 0)
> + VADC_CHAN_VOLT(LR_MUX9_AMUX_THM5, 0)
> + VADC_CHAN_VOLT(LR_MUX10_USB_ID, 0)
> + VADC_CHAN_VOLT(AMUX_PU1, 0)
> + VADC_CHAN_VOLT(AMUX_PU2, 0)
> + VADC_CHAN_VOLT(LR_MUX3_BUF_XO_THERM, 0)
> +
> + VADC_CHAN_VOLT(LR_MUX1_PU1_BAT_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX2_PU1_BAT_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_PU1_XO_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX4_PU1_AMUX_THM1, 0)
> + VADC_CHAN_VOLT(LR_MUX5_PU1_AMUX_THM2, 0)
> + VADC_CHAN_VOLT(LR_MUX6_PU1_AMUX_THM3, 0)
> + VADC_CHAN_VOLT(LR_MUX7_PU1_AMUX_HW_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX8_PU1_AMUX_THM4, 0)
> + VADC_CHAN_VOLT(LR_MUX9_PU1_AMUX_THM5, 0)
> + VADC_CHAN_VOLT(LR_MUX10_PU1_AMUX_USB_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_BUF_PU1_XO_THERM, 0)
> +
> + VADC_CHAN_VOLT(LR_MUX1_PU2_BAT_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX2_PU2_BAT_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_PU2_XO_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX4_PU2_AMUX_THM1, 0)
> + VADC_CHAN_VOLT(LR_MUX5_PU2_AMUX_THM2, 0)
> + VADC_CHAN_VOLT(LR_MUX6_PU2_AMUX_THM3, 0)
> + VADC_CHAN_VOLT(LR_MUX7_PU2_AMUX_HW_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX8_PU2_AMUX_THM4, 0)
> + VADC_CHAN_VOLT(LR_MUX9_PU2_AMUX_THM5, 0)
> + VADC_CHAN_VOLT(LR_MUX10_PU2_AMUX_USB_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_BUF_PU2_XO_THERM, 0)
> +
> + VADC_CHAN_VOLT(LR_MUX1_PU1_PU2_BAT_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX2_PU1_PU2_BAT_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_PU1_PU2_XO_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX4_PU1_PU2_AMUX_THM1, 0)
> + VADC_CHAN_VOLT(LR_MUX5_PU1_PU2_AMUX_THM2, 0)
> + VADC_CHAN_VOLT(LR_MUX6_PU1_PU2_AMUX_THM3, 0)
> + VADC_CHAN_VOLT(LR_MUX7_PU1_PU2_AMUX_HW_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX8_PU1_PU2_AMUX_THM4, 0)
> + VADC_CHAN_VOLT(LR_MUX9_PU1_PU2_AMUX_THM5, 0)
> + VADC_CHAN_VOLT(LR_MUX10_PU1_PU2_AMUX_USB_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_BUF_PU1_PU2_XO_THERM, 0)
> +};
> +
> +static int vadc_get_dt_channel_data(struct device *dev,
> + struct vadc_channel_prop *prop,
> + struct device_node *node)
> +{
> + const char *name = node->name;
> + u32 chan, value, varr[2];
> + int ret;
> +
> + ret = of_property_read_u32(node, "reg", &chan);
> + if (ret) {
> + dev_err(dev, "invalid channel number %s\n", name);
> + return ret;
> + }
> +
> + if (chan > VADC_CHAN_MAX || chan < VADC_CHAN_MIN) {
> + dev_err(dev, "%s invalid channel number %d\n", name, chan);
> + return -EINVAL;
> + }
> +
> + /* the channel has DT description */
> + prop->channel = chan;
> +
> + ret = of_property_read_u32(node, "qcom,decimation", &value);
> + if (!ret) {
> + ret = vadc_decimation_from_dt(value);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid decimation %d\n",
> + chan, value);
> + return ret;
> + }
> + prop->decimation = ret;
> + } else {
> + prop->decimation = VADC_DEF_DECIMATION;
> + }
> +
> + ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2);
> + if (!ret) {
> + ret = vadc_prescaling_from_dt(varr[0], varr[1]);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid pre-scaling <%d %d>\n",
> + chan, varr[0], varr[1]);
> + return ret;
> + }
> + prop->prescale = ret;
> + } else {
> + prop->prescale = vadc_chans[prop->channel].prescale_index;
> + }
> +
> + ret = of_property_read_u32(node, "qcom,hw-settle-time", &value);
> + if (!ret) {
> + ret = vadc_hw_settle_time_from_dt(value);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid hw-settle-time %d us\n",
> + chan, value);
> + return ret;
> + }
> + prop->hw_settle_time = ret;
> + } else {
> + prop->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
> + }
> +
> + ret = of_property_read_u32(node, "qcom,avg-samples", &value);
> + if (!ret) {
> + ret = vadc_avg_samples_from_dt(value);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid avg-samples %d\n",
> + chan, value);
> + return ret;
> + }
> + prop->avg_samples = ret;
> + } else {
> + prop->avg_samples = VADC_DEF_AVG_SAMPLES;
> + }
> +
> + if (of_property_read_bool(node, "qcom,ratiometric"))
> + prop->calibration = VADC_CALIB_RATIOMETRIC;
> + else
> + prop->calibration = VADC_CALIB_ABSOLUTE;
> +
> + dev_dbg(dev, "%02x name %s\n", chan, name);
> +
> + return 0;
> +}
> +
> +static int vadc_get_dt_data(struct vadc_priv *vadc, struct device_node *node)
> +{
> + const struct vadc_channels *vadc_chan;
> + struct iio_chan_spec *iio_chan;
> + struct vadc_channel_prop prop;
> + struct device_node *child;
> + unsigned int index = 0;
> + int ret;
> +
> + vadc->nchannels = of_get_available_child_count(node);
> + if (!vadc->nchannels)
> + return -EINVAL;
> +
> + vadc->iio_chans = devm_kcalloc(vadc->dev, vadc->nchannels,
> + sizeof(*vadc->iio_chans), GFP_KERNEL);
> + if (!vadc->iio_chans)
> + return -ENOMEM;
> +
> + vadc->chan_props = devm_kcalloc(vadc->dev, vadc->nchannels,
> + sizeof(*vadc->chan_props), GFP_KERNEL);
> + if (!vadc->chan_props)
> + return -ENOMEM;
> +
> + iio_chan = vadc->iio_chans;
> +
> + for_each_available_child_of_node(node, child) {
> + ret = vadc_get_dt_channel_data(vadc->dev, &prop, child);
> + if (ret)
> + return ret;
> +
> + vadc->chan_props[index] = prop;
> +
> + vadc_chan = &vadc_chans[prop.channel];
> +
> + iio_chan->channel = prop.channel;
> + iio_chan->datasheet_name = vadc_chan->datasheet_name;
> + iio_chan->info_mask_separate = vadc_chan->info_mask;
> + iio_chan->type = vadc_chan->type;
> + iio_chan->indexed = 1;
> + iio_chan->address = index++;
> +
> + iio_chan++;
> + }
> +
> + /* These channels are mandatory, they are used as reference points */
> + if (!vadc_get_channel(vadc, VADC_REF_1250MV)) {
> + dev_err(vadc->dev, "Please define 1.25V channel\n");
> + return -ENODEV;
> + }
> +
> + if (!vadc_get_channel(vadc, VADC_REF_625MV)) {
> + dev_err(vadc->dev, "Please define 0.625V channel\n");
> + return -ENODEV;
> + }
> +
> + if (!vadc_get_channel(vadc, VADC_VDD_VADC)) {
> + dev_err(vadc->dev, "Please define VDD channel\n");
> + return -ENODEV;
> + }
> +
> + if (!vadc_get_channel(vadc, VADC_GND_REF)) {
> + dev_err(vadc->dev, "Please define GND channel\n");
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +static irqreturn_t vadc_isr(int irq, void *dev_id)
> +{
> + struct vadc_priv *vadc = dev_id;
> +
> + complete(&vadc->complete);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int vadc_check_revision(struct vadc_priv *vadc)
> +{
> + u8 val;
> + int ret;
> +
> + ret = vadc_read(vadc, VADC_PERPH_TYPE, &val);
> + if (ret)
> + return ret;
> +
> + if (val < VADC_PERPH_TYPE_ADC) {
> + dev_err(vadc->dev, "%d is not ADC\n", val);
> + return -ENODEV;
> + }
> +
> + ret = vadc_read(vadc, VADC_PERPH_SUBTYPE, &val);
> + if (ret)
> + return ret;
> +
> + if (val < VADC_PERPH_SUBTYPE_VADC) {
> + dev_err(vadc->dev, "%d is not VADC\n", val);
> + return -ENODEV;
> + }
> +
> + ret = vadc_read(vadc, VADC_REVISION2, &val);
> + if (ret)
> + return ret;
> +
> + if (val < VADC_REVISION2_SUPPORTED_VADC) {
> + dev_err(vadc->dev, "revision %d not supported\n", val);
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +static int vadc_probe(struct platform_device *pdev)
> +{
> + struct device_node *node = pdev->dev.of_node;
> + struct device *dev = &pdev->dev;
> + struct iio_dev *indio_dev;
> + struct vadc_priv *vadc;
> + struct regmap *regmap;
> + int ret, irq_eoc;
> + u32 res;
> +
> + regmap = dev_get_regmap(dev->parent, NULL);
> + if (!regmap)
> + return -ENODEV;
> +
> + ret = of_property_read_u32(node, "reg", &res);
> + if (ret < 0)
> + return -ENODEV;
> +
> + indio_dev = devm_iio_device_alloc(dev, sizeof(*vadc));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + vadc = iio_priv(indio_dev);
> + vadc->regmap = regmap;
> + vadc->dev = dev;
> + vadc->base = res;
> + vadc->are_ref_measured = false;
> + init_completion(&vadc->complete);
> +
> + ret = vadc_check_revision(vadc);
> + if (ret)
> + return ret;
> +
> + ret = vadc_get_dt_data(vadc, node);
> + if (ret)
> + return ret;
> +
> + irq_eoc = platform_get_irq(pdev, 0);
> + if (irq_eoc < 0) {
> + if (irq_eoc == -EPROBE_DEFER || irq_eoc == -EINVAL)
> + return irq_eoc;
> + vadc->poll_eoc = true;
> + } else {
> + ret = devm_request_irq(dev, irq_eoc, vadc_isr, 0,
> + "spmi-vadc", vadc);
> + if (ret)
> + return ret;
> + }
> +
> + ret = vadc_reset(vadc);
> + if (ret) {
> + dev_err(dev, "reset failed\n");
> + return ret;
> + }
> +
> + indio_dev->dev.parent = dev;
> + indio_dev->dev.of_node = node;
> + indio_dev->name = pdev->name;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->info = &vadc_info;
> + indio_dev->channels = vadc->iio_chans;
> + indio_dev->num_channels = vadc->nchannels;
> +
> + return devm_iio_device_register(dev, indio_dev);
> +}
> +
> +static const struct of_device_id vadc_match_table[] = {
> + { .compatible = "qcom,spmi-vadc" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, vadc_match_table);
> +
> +static struct platform_driver vadc_driver = {
> + .driver = {
> + .name = "qcom-spmi-vadc",
> + .of_match_table = vadc_match_table,
> + },
> + .probe = vadc_probe,
> +};
> +module_platform_driver(vadc_driver);
> +
> +MODULE_ALIAS("platform:qcom-spmi-vadc");
> +MODULE_DESCRIPTION("Qualcomm SPMI PMIC voltage ADC driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("Stanimir Varbanov <[email protected]>");
> +MODULE_AUTHOR("Ivan T. Ivanov <[email protected]>");
>
On 05/11/14 00:01, Hartmut Knaack wrote:
> Ivan T. Ivanov schrieb am 03.11.2014 16:24:
>> From: Stanimir Varbanov <[email protected]>
>>
>> Document DT binding for Qualcomm SPMI PMIC voltage ADC
>> driver.
>>
>> Signed-off-by: Stanimir Varbanov <[email protected]>
>> Signed-off-by: Ivan T. Ivanov <[email protected]>
This looks more or less fine to me. One probable typo inline.
As Mark was kind enough to review the earlier version I'd like
to let it sit for a while to see if he has time to have another look
(perhaps at v5 with the trivial bits fixed up!)
>> ---
>> .../devicetree/bindings/iio/adc/qcom,spmi-vadc.txt | 129 +++++++++++++++++++++
>> include/dt-bindings/iio/qcom,spmi-vadc.h | 119 +++++++++++++++++++
>> 2 files changed, 248 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
>> create mode 100644 include/dt-bindings/iio/qcom,spmi-vadc.h
>>
>> diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
>> new file mode 100644
>> index 0000000..2253813
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt
>> @@ -0,0 +1,129 @@
>> +Qualcomm's SPMI PMIC voltage ADC
>> +
>> +SPMI PMIC voltage ADC (VADC) provides interface to clients to read
>> +voltage. The VADC is a 15-bit sigma-delta ADC.
>> +
>> +VADC node:
>> +
>> +- compatible:
>> + Usage: required
>> + Value type: <string>
>> + Definition: Should contain "qcom,spmi-vadc".
>> +
>> +- reg:
>> + Usage: required
>> + Value type: <prop-encoded-array>
>> + Definition: VADC base address and length in the SPMI PMIC register map.
>> +
>> +- #address-cells:
>> + Usage: required
>> + Value type: <u32>
>> + Definition: Must be one. Child node 'reg' property should define ADC
>> + channel number.
>> +
>> +- #size-cells:
>> + Usage: required
>> + Value type: <u32>
>> + Definition: Must be zero.
>> +
>> +- #io-channel-cells:
>> + Usage: required
>> + Value type: <u32>
>> + Definition: Must be one. For details about IIO bindings see:
>> + Documentation/devicetree/bindings/iio/iio-bindings.txt
>> +
>> +- interrupts:
>> + Usage: optional
>> + Value type: <prop-encoded-array>
>> + Definition: End of conversion interrupt.
>> +
>> +Channel node properties:
>> +
>> +- reg:
>> + Usage: required
>> + Value type: <u32>
>> + Definition: ADC channel number.
>> + See include/dt-bindings/iio/qcom,spmi-vadc.h
>> +
>> +- qcom,decimation:
>> + Usage: optional
>> + Value type: <u32>
>> + Definition: This parameters is used to decrease ADC sampling rate.
> Typo: This parameter (singular)
>> + Quicker measurements can be made by reducing decimation ratio.
>> + Valid values are 512, 1024, 2048, 4096.
>> + If property is not found, default value of 512 will be used.
>> +
>> +- qcom,pre-scaling:
>> + Usage: optional
>> + Value type: <u32 array>
>> + Definition: Used for scaling the channel input signal before the signal is
>> + fed to VADC. The configuration for this node is to know the
>> + pre-determined ratio and use it for post scaling. Select one from
>> + the following options.
>> + <1 1>, <1 3>, <1 4>, <1 6>, <1 20>, <1 8>, <10 81>, <1 10>
>> + If property is not found default value depending of chip will be used.
on chip?
>> +
>> +- qcom,ratiometric:
>> + Usage: optional
>> + Value type: <empty>
>> + Definition: Channel calibration type. If this property is specified
>> + VADC will use the VDD reference (1.8V) and GND for channel
>> + calibration. If property is not found, channel will be
>> + calibrated with 0.625V and 1.25V reference channels, also
>> + known as absolute calibration.
>> +
>> +- qcom,hw-settle-time:
>> + Usage: optional
>> + Value type: <u32>
>> + Definition: Time between AMUX getting configured and the ADC starting
>> + conversion. Delay = 100us * (value) for value < 11, and
>> + 2ms * (value - 10) otherwise.
>> + Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800,
>> + 900 us and 1, 2, 4, 6, 8, 10 ms
>> + If property is not found, channel will use 0us.
>> +
>> +- qcom,avg-samples:
>> + Usage: optional
>> + Value type: <u32>
>> + Definition: Number of samples to be used for measurement.
>> + Averaging provides the option to obtain a single measurement
>> + from the ADC that is an average of multiple samples. The value
>> + selected is 2^(value).
>> + Valid values are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512
>> + If property is not found, 1 sample will be used.
>> +
>> +NOTE:
>> +
>> +Following channels, also know as reference points channels, are used for
> Typos: <...> also known as reference point channels <...>
>> +result calibration and their channel configuration nodes should be defined:
>> +VADC_REF_625MV and/or VADC_SPARE1, based on PMIC version, VADC_REF_1250MV,
> Better put the "based on PMIC version" into parenthesis.
>> +VADC_GND_REF and VADC_VDD_VADC.
>> +
>> +Example:
>> +
>> + /* VADC node */
>> + pmic_vadc: vadc@3100 {
>> + compatible = "qcom,spmi-vadc";
>> + reg = <0x3100 0x100>;
>> + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #io-channel-cells = <1>;
>> + io-channel-ranges;
>> +
>> + /* Channel node */
>> + usb_id_nopull {
>> + reg = <VADC_LR_MUX10_USB_ID>;
>> + qcom,decimation = <512>;
>> + qcom,ratiometric;
>> + qcom,hw-settle-time = <200>;
>> + qcom,avg-samples = <1>;
>> + qcom,pre-scaling = <1 3>;
>> + };
>> + };
>> +
>> + /* IIO client node */
>> + usb {
>> + io-channels = <&pmic_vadc VADC_LR_MUX10_USB_ID>;
>> + io-channel-names = "vadc";
>> + };
>> diff --git a/include/dt-bindings/iio/qcom,spmi-vadc.h b/include/dt-bindings/iio/qcom,spmi-vadc.h
>> new file mode 100644
>> index 0000000..42121fa
>> --- /dev/null
>> +++ b/include/dt-bindings/iio/qcom,spmi-vadc.h
>> @@ -0,0 +1,119 @@
>> +/*
>> + * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 and
>> + * only version 2 as published by the Free Software Foundation.
>> + *
>> + * This program is distributed in the hope that it will be useful
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#ifndef _DT_BINDINGS_QCOM_SPMI_VADC_H
>> +#define _DT_BINDINGS_QCOM_SPMI_VADC_H
>> +
>> +/* Voltage ADC channels */
>> +#define VADC_USBIN 0x00
>> +#define VADC_DCIN 0x01
>> +#define VADC_VCHG_SNS 0x02
>> +#define VADC_SPARE1_03 0x03
>> +#define VADC_USB_ID_MV 0x04
>> +#define VADC_VCOIN 0x05
>> +#define VADC_VBAT_SNS 0x06
>> +#define VADC_VSYS 0x07
>> +#define VADC_DIE_TEMP 0x08
>> +#define VADC_REF_625MV 0x09
>> +#define VADC_REF_1250MV 0x0a
>> +#define VADC_CHG_TEMP 0x0b
>> +#define VADC_SPARE1 0x0c
>> +#define VADC_SPARE2 0x0d
>> +#define VADC_GND_REF 0x0e
>> +#define VADC_VDD_VADC 0x0f
>> +
>> +#define VADC_P_MUX1_1_1 0x10
>> +#define VADC_P_MUX2_1_1 0x11
>> +#define VADC_P_MUX3_1_1 0x12
>> +#define VADC_P_MUX4_1_1 0x13
>> +#define VADC_P_MUX5_1_1 0x14
>> +#define VADC_P_MUX6_1_1 0x15
>> +#define VADC_P_MUX7_1_1 0x16
>> +#define VADC_P_MUX8_1_1 0x17
>> +#define VADC_P_MUX9_1_1 0x18
>> +#define VADC_P_MUX10_1_1 0x19
>> +#define VADC_P_MUX11_1_1 0x1a
>> +#define VADC_P_MUX12_1_1 0x1b
>> +#define VADC_P_MUX13_1_1 0x1c
>> +#define VADC_P_MUX14_1_1 0x1d
>> +#define VADC_P_MUX15_1_1 0x1e
>> +#define VADC_P_MUX16_1_1 0x1f
>> +
>> +#define VADC_P_MUX1_1_3 0x20
>> +#define VADC_P_MUX2_1_3 0x21
>> +#define VADC_P_MUX3_1_3 0x22
>> +#define VADC_P_MUX4_1_3 0x23
>> +#define VADC_P_MUX5_1_3 0x24
>> +#define VADC_P_MUX6_1_3 0x25
>> +#define VADC_P_MUX7_1_3 0x26
>> +#define VADC_P_MUX8_1_3 0x27
>> +#define VADC_P_MUX9_1_3 0x28
>> +#define VADC_P_MUX10_1_3 0x29
>> +#define VADC_P_MUX11_1_3 0x2a
>> +#define VADC_P_MUX12_1_3 0x2b
>> +#define VADC_P_MUX13_1_3 0x2c
>> +#define VADC_P_MUX14_1_3 0x2d
>> +#define VADC_P_MUX15_1_3 0x2e
>> +#define VADC_P_MUX16_1_3 0x2f
>> +
>> +#define VADC_LR_MUX1_BAT_THERM 0x30
>> +#define VADC_LR_MUX2_BAT_ID 0x31
>> +#define VADC_LR_MUX3_XO_THERM 0x32
>> +#define VADC_LR_MUX4_AMUX_THM1 0x33
>> +#define VADC_LR_MUX5_AMUX_THM2 0x34
>> +#define VADC_LR_MUX6_AMUX_THM3 0x35
>> +#define VADC_LR_MUX7_HW_ID 0x36
>> +#define VADC_LR_MUX8_AMUX_THM4 0x37
>> +#define VADC_LR_MUX9_AMUX_THM5 0x38
>> +#define VADC_LR_MUX10_USB_ID 0x39
>> +#define VADC_AMUX_PU1 0x3a
>> +#define VADC_AMUX_PU2 0x3b
>> +#define VADC_LR_MUX3_BUF_XO_THERM 0x3c
>> +
>> +#define VADC_LR_MUX1_PU1_BAT_THERM 0x70
>> +#define VADC_LR_MUX2_PU1_BAT_ID 0x71
>> +#define VADC_LR_MUX3_PU1_XO_THERM 0x72
>> +#define VADC_LR_MUX4_PU1_AMUX_THM1 0x73
>> +#define VADC_LR_MUX5_PU1_AMUX_THM2 0x74
>> +#define VADC_LR_MUX6_PU1_AMUX_THM3 0x75
>> +#define VADC_LR_MUX7_PU1_AMUX_HW_ID 0x76
>> +#define VADC_LR_MUX8_PU1_AMUX_THM4 0x77
>> +#define VADC_LR_MUX9_PU1_AMUX_THM5 0x78
>> +#define VADC_LR_MUX10_PU1_AMUX_USB_ID 0x79
>> +#define VADC_LR_MUX3_BUF_PU1_XO_THERM 0x7c
>> +
>> +#define VADC_LR_MUX1_PU2_BAT_THERM 0xb0
>> +#define VADC_LR_MUX2_PU2_BAT_ID 0xb1
>> +#define VADC_LR_MUX3_PU2_XO_THERM 0xb2
>> +#define VADC_LR_MUX4_PU2_AMUX_THM1 0xb3
>> +#define VADC_LR_MUX5_PU2_AMUX_THM2 0xb4
>> +#define VADC_LR_MUX6_PU2_AMUX_THM3 0xb5
>> +#define VADC_LR_MUX7_PU2_AMUX_HW_ID 0xb6
>> +#define VADC_LR_MUX8_PU2_AMUX_THM4 0xb7
>> +#define VADC_LR_MUX9_PU2_AMUX_THM5 0xb8
>> +#define VADC_LR_MUX10_PU2_AMUX_USB_ID 0xb9
>> +#define VADC_LR_MUX3_BUF_PU2_XO_THERM 0xbc
>> +
>> +#define VADC_LR_MUX1_PU1_PU2_BAT_THERM 0xf0
>> +#define VADC_LR_MUX2_PU1_PU2_BAT_ID 0xf1
>> +#define VADC_LR_MUX3_PU1_PU2_XO_THERM 0xf2
>> +#define VADC_LR_MUX4_PU1_PU2_AMUX_THM1 0xf3
>> +#define VADC_LR_MUX5_PU1_PU2_AMUX_THM2 0xf4
>> +#define VADC_LR_MUX6_PU1_PU2_AMUX_THM3 0xf5
>> +#define VADC_LR_MUX7_PU1_PU2_AMUX_HW_ID 0xf6
>> +#define VADC_LR_MUX8_PU1_PU2_AMUX_THM4 0xf7
>> +#define VADC_LR_MUX9_PU1_PU2_AMUX_THM5 0xf8
>> +#define VADC_LR_MUX10_PU1_PU2_AMUX_USB_ID 0xf9
>> +#define VADC_LR_MUX3_BUF_PU1_PU2_XO_THERM 0xfc
>> +
>> +#endif /* _DT_BINDINGS_QCOM_SPMI_VADC_H */
>>
>
On Wed, 2014-11-05 at 13:09 +0000, Jonathan Cameron wrote:
> On 03/11/14 15:24, Ivan T. Ivanov wrote:
> > From: Stanimir Varbanov <[email protected]>
> >
> > The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
> > 15 bits resolution and register space inside PMIC accessible across
> > SPMI bus.
> >
> > The vadc driver registers itself through IIO interface.
> >
> > Signed-off-by: Stanimir Varbanov <[email protected]>
> > Signed-off-by: Ivan T. Ivanov <[email protected]>
> Hi Ivan,
>
> Couple of utterly tiny bits inline. The biggest one is that
> you store some info about the calibration that you never actually
> use... Left over from some debugging perhaps?
>
> Jonathan
<snip>
> > +
> > +/*
> > + * VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
> > + * VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
> > + * calibration.
> > + */
> > +enum vadc_calibration {
> > + VADC_CALIB_ABSOLUTE = 0,
> > + VADC_CALIB_RATIOMETRIC
> > +};
> > +
> > +/**
> > + * struct vadc_linear_graph - Represent ADC characteristics.
> > + * @dy: numerator slope to calculate the gain.
> As dy is always equal to vref-gnd you could drop it and use those
> directly...
>
> Conversly you store vref or grnd and never use them...
I am not sure I am following you. Please take a look in
vadc_measure_ref_points() and vadc_calibrate().
>
> > + * @dx: denominator slope to calculate the gain.
> > + * @vref: A/D word of the voltage reference used for the channel.
> > + * @gnd: A/D word of the ground reference used for the channel.
> > + *
> > + * Each ADC device has different offset and gain parameters which are
> > + * computed to calibrate the device.
> > + */
> > +struct vadc_linear_graph {
> > + s32 dy;
> > + s32 dx;
> > + s32 vref;
> > + s32 gnd;
> > +};
> > +
> >
Will address blank line comment.
Regards,
Ivan
On 05/11/14 13:57, Ivan T. Ivanov wrote:
>
> On Wed, 2014-11-05 at 13:09 +0000, Jonathan Cameron wrote:
>> On 03/11/14 15:24, Ivan T. Ivanov wrote:
>>> From: Stanimir Varbanov <[email protected]>
>>>
>>> The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
>>> 15 bits resolution and register space inside PMIC accessible across
>>> SPMI bus.
>>>
>>> The vadc driver registers itself through IIO interface.
>>>
>>> Signed-off-by: Stanimir Varbanov <[email protected]>
>>> Signed-off-by: Ivan T. Ivanov <[email protected]>
>> Hi Ivan,
>>
>> Couple of utterly tiny bits inline. The biggest one is that
>> you store some info about the calibration that you never actually
>> use... Left over from some debugging perhaps?
>>
>> Jonathan
>
> <snip>
>
>>> +
>>> +/*
>>> + * VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
>>> + * VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
>>> + * calibration.
>>> + */
>>> +enum vadc_calibration {
>>> + VADC_CALIB_ABSOLUTE = 0,
>>> + VADC_CALIB_RATIOMETRIC
>>> +};
>>> +
>>> +/**
>>> + * struct vadc_linear_graph - Represent ADC characteristics.
>>> + * @dy: numerator slope to calculate the gain.
>> As dy is always equal to vref-gnd you could drop it and use those
>> directly...
>>
>> Conversly you store vref or grnd and never use them...
>
> I am not sure I am following you. Please take a look in
> vadc_measure_ref_points() and vadc_calibrate().
Good point on grnd, but vref is set but never read anywhere that I can find..
>
>>
>>> + * @dx: denominator slope to calculate the gain.
>>> + * @vref: A/D word of the voltage reference used for the channel.
>>> + * @gnd: A/D word of the ground reference used for the channel.
>>> + *
>>> + * Each ADC device has different offset and gain parameters which are
>>> + * computed to calibrate the device.
>>> + */
>>> +struct vadc_linear_graph {
>>> + s32 dy;
>>> + s32 dx;
>>> + s32 vref;
>>> + s32 gnd;
>>> +};
>>> +
>>>
>
> Will address blank line comment.
>
> Regards,
> Ivan
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
Thank you, will fix typos pointed by you and Jonathan.
Regards,
Ivan
On Wed, 2014-11-05 at 14:06 +0000, Jonathan Cameron wrote:
> On 05/11/14 13:57, Ivan T. Ivanov wrote:
> > On Wed, 2014-11-05 at 13:09 +0000, Jonathan Cameron wrote:
> > > On 03/11/14 15:24, Ivan T. Ivanov wrote:
> > > > From: Stanimir Varbanov <[email protected]>
> > > >
> > > > The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
> > > > 15 bits resolution and register space inside PMIC accessible across
> > > > SPMI bus.
> > > >
> > > > The vadc driver registers itself through IIO interface.
> > > >
> > > > Signed-off-by: Stanimir Varbanov <[email protected]>
> > > > Signed-off-by: Ivan T. Ivanov <[email protected]>
> > > Hi Ivan,
> > >
> > > Couple of utterly tiny bits inline. The biggest one is that
> > > you store some info about the calibration that you never actually
> > > use... Left over from some debugging perhaps?
> > >
> > > Jonathan
> >
> > <snip>
> >
> > > > +
> > > > +/*
> > > > + * VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
> > > > + * VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
> > > > + * calibration.
> > > > + */
> > > > +enum vadc_calibration {
> > > > + VADC_CALIB_ABSOLUTE = 0,
> > > > + VADC_CALIB_RATIOMETRIC
> > > > +};
> > > > +
> > > > +/**
> > > > + * struct vadc_linear_graph - Represent ADC characteristics.
> > > > + * @dy: numerator slope to calculate the gain.
> > > As dy is always equal to vref-gnd you could drop it and use those
> > > directly...
> > >
> > > Conversly you store vref or grnd and never use them...
> >
> > I am not sure I am following you. Please take a look in
> > vadc_measure_ref_points() and vadc_calibrate().
> Good point on grnd, but vref is set but never read anywhere that I can find..
>
Right. At this point it is not used. Driver right now provide basic per
channel voltage measurements. The plan is to add temperature compensation for the
measurements and additional scaling functions which are specific per channel.
I could drop this field from initial driver version if you like.
Regards,
Ivan
On 05/11/14 15:01, Ivan T. Ivanov wrote:
>
> On Wed, 2014-11-05 at 14:06 +0000, Jonathan Cameron wrote:
>> On 05/11/14 13:57, Ivan T. Ivanov wrote:
>>> On Wed, 2014-11-05 at 13:09 +0000, Jonathan Cameron wrote:
>>>> On 03/11/14 15:24, Ivan T. Ivanov wrote:
>>>>> From: Stanimir Varbanov <[email protected]>
>>>>>
>>>>> The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
>>>>> 15 bits resolution and register space inside PMIC accessible across
>>>>> SPMI bus.
>>>>>
>>>>> The vadc driver registers itself through IIO interface.
>>>>>
>>>>> Signed-off-by: Stanimir Varbanov <[email protected]>
>>>>> Signed-off-by: Ivan T. Ivanov <[email protected]>
>>>> Hi Ivan,
>>>>
>>>> Couple of utterly tiny bits inline. The biggest one is that
>>>> you store some info about the calibration that you never actually
>>>> use... Left over from some debugging perhaps?
>>>>
>>>> Jonathan
>>>
>>> <snip>
>>>
>>>>> +
>>>>> +/*
>>>>> + * VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
>>>>> + * VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
>>>>> + * calibration.
>>>>> + */
>>>>> +enum vadc_calibration {
>>>>> + VADC_CALIB_ABSOLUTE = 0,
>>>>> + VADC_CALIB_RATIOMETRIC
>>>>> +};
>>>>> +
>>>>> +/**
>>>>> + * struct vadc_linear_graph - Represent ADC characteristics.
>>>>> + * @dy: numerator slope to calculate the gain.
>>>> As dy is always equal to vref-gnd you could drop it and use those
>>>> directly...
>>>>
>>>> Conversly you store vref or grnd and never use them...
>>>
>>> I am not sure I am following you. Please take a look in
>>> vadc_measure_ref_points() and vadc_calibrate().
>> Good point on grnd, but vref is set but never read anywhere that I can find..
>>
>
> Right. At this point it is not used. Driver right now provide basic per
> channel voltage measurements. The plan is to add temperature compensation for the
> measurements and additional scaling functions which are specific per channel.
>
> I could drop this field from initial driver version if you like.
Probably best as otherwise some compiler in a clever mood will give
a warning and I'll get an irritating patch to remove it!
J
>
> Regards,
> Ivan
>
Ivan T. Ivanov schrieb am 03.11.2014 16:24:
> From: Stanimir Varbanov <[email protected]>
>
> The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
> 15 bits resolution and register space inside PMIC accessible across
> SPMI bus.
>
> The vadc driver registers itself through IIO interface.
Reviewing again, I got the feeling that due to the complexity of adc reads (writing to register to start conversion, waiting a decent time for the conversion to complete, reading the result), it would be beneficial to use a mutex in vadc_read_raw or its depending functions.
Also, I would want to double-check that the CPU in this type of chips is little endian.
Besides that, a few minor issues inline.
>
> Signed-off-by: Stanimir Varbanov <[email protected]>
> Signed-off-by: Ivan T. Ivanov <[email protected]>
> ---
> drivers/iio/adc/Kconfig | 14 +
> drivers/iio/adc/Makefile | 1 +
> drivers/iio/adc/qcom-spmi-vadc.c | 1015 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 1030 insertions(+)
> create mode 100644 drivers/iio/adc/qcom-spmi-vadc.c
>
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 88bdc8f..af6e10b 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -206,6 +206,20 @@ config NAU7802
> To compile this driver as a module, choose M here: the
> module will be called nau7802.
>
> +config QCOM_SPMI_VADC
> + tristate "Qualcomm SPMI PMIC voltage ADC"
> + depends on SPMI
> + select REGMAP_SPMI
> + help
> + This is the IIO Voltage ADC driver for Qualcomm QPNP VADC Chip.
> +
> + The driver supports multiple channels read. The VADC is a 15-bit
> + sigma-delta ADC. Some of the channels are internally used for
> + calibration.
> +
> + To compile this driver as a module, choose M here: the module will
> + be called qcom-spmi-vadc.
> +
> config ROCKCHIP_SARADC
> tristate "Rockchip SARADC driver"
> depends on ARCH_ROCKCHIP || (ARM && COMPILE_TEST)
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index cb88a6a..479b457 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -22,6 +22,7 @@ obj-$(CONFIG_MCP320X) += mcp320x.o
> obj-$(CONFIG_MCP3422) += mcp3422.o
> obj-$(CONFIG_MEN_Z188_ADC) += men_z188_adc.o
> obj-$(CONFIG_NAU7802) += nau7802.o
> +obj-$(CONFIG_QCOM_SPMI_VADC) += qcom-spmi-vadc.o
> obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o
> obj-$(CONFIG_TI_ADC081C) += ti-adc081c.o
> obj-$(CONFIG_TI_ADC128S052) += ti-adc128s052.o
> diff --git a/drivers/iio/adc/qcom-spmi-vadc.c b/drivers/iio/adc/qcom-spmi-vadc.c
> new file mode 100644
> index 0000000..6e6881c
> --- /dev/null
> +++ b/drivers/iio/adc/qcom-spmi-vadc.c
> @@ -0,0 +1,1015 @@
> +/*
> + * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/completion.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/iio/iio.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +#include <linux/log2.h>
> +
> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> +
> +/* VADC register and bit definitions */
> +#define VADC_REVISION2 0x1
> +#define VADC_REVISION2_SUPPORTED_VADC 1
> +
> +#define VADC_PERPH_TYPE 0x4
> +#define VADC_PERPH_TYPE_ADC 8
> +
> +#define VADC_PERPH_SUBTYPE 0x5
> +#define VADC_PERPH_SUBTYPE_VADC 1
> +
> +#define VADC_STATUS1 0x8
> +#define VADC_STATUS1_OP_MODE 4
> +#define VADC_STATUS1_REQ_STS BIT(1)
> +#define VADC_STATUS1_EOC BIT(0)
> +#define VADC_STATUS1_REQ_STS_EOC_MASK 0x3
> +
> +#define VADC_MODE_CTL 0x40
> +#define VADC_OP_MODE_SHIFT 3
> +#define VADC_OP_MODE_NORMAL 0
> +#define VADC_AMUX_TRIM_EN BIT(1)
> +#define VADC_ADC_TRIM_EN BIT(0)
> +
> +#define VADC_EN_CTL1 0x46
> +#define VADC_EN_CTL1_SET BIT(7)
> +
> +#define VADC_ADC_CH_SEL_CTL 0x48
> +
> +#define VADC_ADC_DIG_PARAM 0x50
> +#define VADC_ADC_DIG_DEC_RATIO_SEL_SHIFT 2
> +
> +#define VADC_HW_SETTLE_DELAY 0x51
> +
> +#define VADC_CONV_REQ 0x52
> +#define VADC_CONV_REQ_SET BIT(7)
> +
> +#define VADC_FAST_AVG_CTL 0x5a
> +#define VADC_FAST_AVG_EN 0x5b
> +#define VADC_FAST_AVG_EN_SET BIT(7)
> +
> +#define VADC_ACCESS 0xd0
> +#define VADC_ACCESS_DATA 0xa5
> +
> +#define VADC_PERH_RESET_CTL3 0xda
> +#define VADC_FOLLOW_WARM_RB BIT(2)
> +
> +#define VADC_DATA 0x60 /* 16 bits */
> +
> +#define VADC_CONV_TIME_MIN_US 2000
> +#define VADC_CONV_TIME_MAX_US 2100
> +
> +/* Min ADC code represents 0V */
> +#define VADC_MIN_ADC_CODE 0x6000
> +/* Max ADC code represents full-scale range of 1.8V */
> +#define VADC_MAX_ADC_CODE 0xa800
> +
> +#define VADC_ABSOLUTE_RANGE_UV 625000
> +#define VADC_RATIOMETRIC_RANGE_UV 1800000
> +
> +#define VADC_DEF_PRESCALING 0 /* 1:1 */
> +#define VADC_DEF_DECIMATION 0 /* 512 */
> +#define VADC_DEF_HW_SETTLE_TIME 0 /* 0 us */
> +#define VADC_DEF_AVG_SAMPLES 0 /* 1 sample */
> +#define VADC_DEF_CALIB_TYPE VADC_CALIB_ABSOLUTE
> +
> +#define VADC_DECIMATION_MIN 512
> +#define VADC_DECIMATION_MAX 4096
> +
> +#define VADC_HW_SETTLE_DELAY_MAX 10000
> +#define VADC_AVG_SAMPLES_MAX 512
> +
> +#define KELVINMIL_CELSIUSMIL 273150
> +
> +#define VADC_CHAN_MIN VADC_USBIN
> +#define VADC_CHAN_MAX VADC_LR_MUX3_BUF_PU1_PU2_XO_THERM
> +
> +/*
> + * VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
> + * VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
> + * calibration.
> + */
> +enum vadc_calibration {
> + VADC_CALIB_ABSOLUTE = 0,
> + VADC_CALIB_RATIOMETRIC
> +};
> +
> +/**
> + * struct vadc_linear_graph - Represent ADC characteristics.
> + * @dy: numerator slope to calculate the gain.
> + * @dx: denominator slope to calculate the gain.
> + * @vref: A/D word of the voltage reference used for the channel.
> + * @gnd: A/D word of the ground reference used for the channel.
> + *
> + * Each ADC device has different offset and gain parameters which are
> + * computed to calibrate the device.
> + */
> +struct vadc_linear_graph {
> + s32 dy;
> + s32 dx;
> + s32 vref;
> + s32 gnd;
> +};
> +
> +/**
> + * struct vadc_prescale_ratio - Represent scaling ratio for ADC input.
> + * @num: the inverse numerator of the gain applied to the input channel.
> + * @den: the inverse denominator of the gain applied to the input channel.
> + */
> +struct vadc_prescale_ratio {
> + u32 num;
> + u32 den;
> +};
> +
> +/**
> + * struct vadc_channel_prop - VADC channel property.
> + * @channel: channel number, refer to the channel list.
> + * @calibration: calibration type.
> + * @decimation: sampling rate supported for the channel.
> + * @prescale: channel scaling performed on the input signal.
> + * @hw_settle_time: the time between AMUX being configured and the
> + * start of conversion.
> + * @avg_samples: ability to provide single result from the ADC
> + * that is an average of multiple measurements.
> + */
> +struct vadc_channel_prop {
> + unsigned int channel;
> + enum vadc_calibration calibration;
> + unsigned int decimation;
> + unsigned int prescale;
> + unsigned int hw_settle_time;
> + unsigned int avg_samples;
> +};
> +
> +/**
> + * struct vadc_priv - VADC private structure.
> + * @regmap: pointer to struct regmap.
> + * @dev: pointer to struct device.
> + * @base: base address for the ADC peripheral.
> + * @nchannels: number of VADC channels.
> + * @chan_props: array of VADC channel properties.
> + * @iio_chans: array of IIO channels specification.
> + * @are_ref_measured: are reference points measured.
> + * @poll_eoc: use polling instead of interrupt.
> + * @complete: VADC result notification after interrupt is received.
> + * @graph: store parameters for calibration.
> + */
> +struct vadc_priv {
> + struct regmap *regmap;
> + struct device *dev;
> + u16 base;
> + unsigned int nchannels;
> + struct vadc_channel_prop *chan_props;
> + struct iio_chan_spec *iio_chans;
> + bool are_ref_measured;
> + bool poll_eoc;
> + struct completion complete;
> + struct vadc_linear_graph graph[2];
> +};
> +
> +static const struct vadc_prescale_ratio vadc_prescale_ratios[] = {
> + {.num = 1, .den = 1},
> + {.num = 1, .den = 3},
> + {.num = 1, .den = 4},
> + {.num = 1, .den = 6},
> + {.num = 1, .den = 20},
> + {.num = 1, .den = 8},
> + {.num = 10, .den = 81},
> + {.num = 1, .den = 10}
> +};
> +
> +static int vadc_read(struct vadc_priv *vadc, u16 offset, u8 *data)
> +{
> + return regmap_bulk_read(vadc->regmap, vadc->base + offset, data, 1);
> +}
> +
> +static int vadc_write(struct vadc_priv *vadc, u16 offset, u8 data)
> +{
> + return regmap_write(vadc->regmap, vadc->base + offset, data);
> +}
> +
> +static int vadc_reset(struct vadc_priv *vadc)
> +{
> + u8 data;
> + int ret;
> +
> + ret = vadc_write(vadc, VADC_ACCESS, VADC_ACCESS_DATA);
> + if (ret)
> + return ret;
> +
> + ret = vadc_read(vadc, VADC_PERH_RESET_CTL3, &data);
> + if (ret)
> + return ret;
> +
> + ret = vadc_write(vadc, VADC_ACCESS, VADC_ACCESS_DATA);
> + if (ret)
> + return ret;
> +
> + data |= VADC_FOLLOW_WARM_RB;
> +
> + return vadc_write(vadc, VADC_PERH_RESET_CTL3, data);
> +}
> +
> +static int vadc_set_state(struct vadc_priv *vadc, bool state)
> +{
> + return vadc_write(vadc, VADC_EN_CTL1, state ? VADC_EN_CTL1_SET : 0);
> +}
> +
> +static void vadc_show_status(struct vadc_priv *vadc)
> +{
> + u8 mode, sta1, chan, dig, en, req;
> + int ret;
> +
> + ret = vadc_read(vadc, VADC_MODE_CTL, &mode);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_ADC_DIG_PARAM, &dig);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_ADC_CH_SEL_CTL, &chan);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_CONV_REQ, &req);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_STATUS1, &sta1);
> + if (ret)
> + return;
> +
> + ret = vadc_read(vadc, VADC_EN_CTL1, &en);
> + if (ret)
> + return;
> +
> + dev_err(vadc->dev,
> + "mode:%02x en:%02x chan:%02x dig:%02x req:%02x sta1:%02x\n",
> + mode, en, chan, dig, req, sta1);
> +}
> +
> +static int vadc_configure(struct vadc_priv *vadc,
> + struct vadc_channel_prop *prop)
> +{
> + u8 decimation, mode_ctrl;
> + int ret;
> +
> + /* Mode selection */
> + mode_ctrl = (VADC_OP_MODE_NORMAL << VADC_OP_MODE_SHIFT) |
> + VADC_ADC_TRIM_EN | VADC_AMUX_TRIM_EN;
> + ret = vadc_write(vadc, VADC_MODE_CTL, mode_ctrl);
> + if (ret)
> + return ret;
> +
> + /* Channel selection */
> + ret = vadc_write(vadc, VADC_ADC_CH_SEL_CTL, prop->channel);
> + if (ret)
> + return ret;
> +
> + /* Digital parameter setup */
> + decimation = prop->decimation << VADC_ADC_DIG_DEC_RATIO_SEL_SHIFT;
> + ret = vadc_write(vadc, VADC_ADC_DIG_PARAM, decimation);
> + if (ret)
> + return ret;
> +
> + /* HW settle time delay */
> + ret = vadc_write(vadc, VADC_HW_SETTLE_DELAY, prop->hw_settle_time);
> + if (ret)
> + return ret;
> +
> + ret = vadc_write(vadc, VADC_FAST_AVG_CTL, prop->avg_samples);
> + if (ret)
> + return ret;
> +
> + if (prop->avg_samples)
> + ret = vadc_write(vadc, VADC_FAST_AVG_EN, VADC_FAST_AVG_EN_SET);
> + else
> + ret = vadc_write(vadc, VADC_FAST_AVG_EN, 0);
> +
> + return ret;
> +}
> +
> +static int vadc_poll_wait_eoc(struct vadc_priv *vadc, unsigned int interval_us)
> +{
> + unsigned int count, retry;
> + u8 sta1;
> + int ret;
> +
> + retry = interval_us / VADC_CONV_TIME_MIN_US;
> +
> + for (count = 0; count < retry; count++) {
> + ret = vadc_read(vadc, VADC_STATUS1, &sta1);
> + if (ret)
> + return ret;
> +
> + sta1 &= VADC_STATUS1_REQ_STS_EOC_MASK;
> + if (sta1 == VADC_STATUS1_EOC)
> + return 0;
> +
> + usleep_range(VADC_CONV_TIME_MIN_US, VADC_CONV_TIME_MAX_US);
> + }
> +
> + vadc_show_status(vadc);
> +
> + return -ETIMEDOUT;
> +}
> +
> +static int vadc_read_result(struct vadc_priv *vadc, u16 *data)
> +{
> + int ret;
> +
> + ret = regmap_bulk_read(vadc->regmap, vadc->base + VADC_DATA, data, 2);
> + if (ret)
> + return ret;
> +
> + *data = clamp_t(u16, *data, VADC_MIN_ADC_CODE, VADC_MAX_ADC_CODE);
> + return 0;
> +}
> +
> +static struct vadc_channel_prop *vadc_get_channel(struct vadc_priv *vadc,
> + unsigned int num)
> +{
> + unsigned int i;
> +
> + for (i = 0; i < vadc->nchannels; i++)
> + if (vadc->chan_props[i].channel == num)
> + return &vadc->chan_props[i];
> +
> + dev_dbg(vadc->dev, "no such channel %02x\n", num);
> +
> + return NULL;
> +}
> +
> +static int vadc_do_conversion(struct vadc_priv *vadc,
> + struct vadc_channel_prop *prop, u16 *data)
> +{
> + unsigned int timeout;
> + int ret;
> +
> + ret = vadc_configure(vadc, prop);
> + if (ret)
> + return ret;
> +
> + if (!vadc->poll_eoc)
> + reinit_completion(&vadc->complete);
> +
> + ret = vadc_set_state(vadc, true);
> + if (ret)
> + return ret;
> +
> + ret = vadc_write(vadc, VADC_CONV_REQ, VADC_CONV_REQ_SET);
> + if (ret)
> + goto err_disable;
> +
> + timeout = BIT(prop->avg_samples) * VADC_CONV_TIME_MIN_US * 2;
> +
> + if (vadc->poll_eoc) {
> + ret = vadc_poll_wait_eoc(vadc, timeout);
> + } else {
> + ret = wait_for_completion_timeout(&vadc->complete, timeout);
> + if (!ret) {
> + ret = -ETIMEDOUT;
> + goto err_disable;
> + }
> +
> + /* Double check conversion status */
> + ret = vadc_poll_wait_eoc(vadc, VADC_CONV_TIME_MIN_US);
> + if (ret)
> + goto err_disable;
> + }
> +
> + ret = vadc_read_result(vadc, data);
> +
> +err_disable:
> + vadc_set_state(vadc, false);
> + if (ret)
> + dev_err(vadc->dev, "conversion failed\n");
> +
> + return ret;
> +}
> +
> +static int vadc_measure_ref_points(struct vadc_priv *vadc)
> +{
> + struct vadc_channel_prop *prop;
> + u16 read_1, read_2;
> + int ret;
> +
> + vadc->graph[VADC_CALIB_RATIOMETRIC].dx = VADC_RATIOMETRIC_RANGE_UV;
> + vadc->graph[VADC_CALIB_ABSOLUTE].dx = VADC_ABSOLUTE_RANGE_UV;
> +
> + prop = vadc_get_channel(vadc, VADC_REF_1250MV);
> + ret = vadc_do_conversion(vadc, prop, &read_1);
> + if (ret)
> + goto err;
> +
> + /* Try with buffered 625mV channel first */
> + prop = vadc_get_channel(vadc, VADC_SPARE1);
> + if (!prop)
> + prop = vadc_get_channel(vadc, VADC_REF_625MV);
> +
> + ret = vadc_do_conversion(vadc, prop, &read_2);
> + if (ret)
> + goto err;
> +
> + if (read_1 == read_2) {
> + ret = -EINVAL;
> + goto err;
> + }
> +
> + vadc->graph[VADC_CALIB_ABSOLUTE].dy = read_1 - read_2;
> + vadc->graph[VADC_CALIB_ABSOLUTE].vref = read_1;
> + vadc->graph[VADC_CALIB_ABSOLUTE].gnd = read_2;
> +
> + /* Ratiometric calibration */
> + prop = vadc_get_channel(vadc, VADC_VDD_VADC);
> + ret = vadc_do_conversion(vadc, prop, &read_1);
> + if (ret)
> + goto err;
> +
> + prop = vadc_get_channel(vadc, VADC_GND_REF);
> + ret = vadc_do_conversion(vadc, prop, &read_2);
> + if (ret)
> + goto err;
> +
> + if (read_1 == read_2) {
> + ret = -EINVAL;
> + goto err;
> + }
> +
> + vadc->graph[VADC_CALIB_RATIOMETRIC].dy = read_1 - read_2;
> + vadc->graph[VADC_CALIB_RATIOMETRIC].vref = read_1;
> + vadc->graph[VADC_CALIB_RATIOMETRIC].gnd = read_2;
> +err:
> + if (ret)
> + dev_err(vadc->dev, "measure reference points failed\n");
> +
> + return ret;
> +}
> +
> +static s32 vadc_calibrate(struct vadc_priv *vadc,
> + const struct vadc_channel_prop *prop, u16 adc_code)
> +{
> + const struct vadc_prescale_ratio *prescale;
> + s32 voltage;
> +
> + voltage = adc_code - vadc->graph[prop->calibration].gnd;
> + voltage *= vadc->graph[prop->calibration].dx;
> + voltage = voltage / vadc->graph[prop->calibration].dy;
> +
> + if (prop->calibration == VADC_CALIB_ABSOLUTE)
> + voltage += vadc->graph[prop->calibration].dx;
> +
> + if (voltage < 0)
> + voltage = 0;
> +
> + prescale = &vadc_prescale_ratios[prop->prescale];
> +
> + voltage = voltage * prescale->den;
> +
> + return voltage / prescale->num;
> +}
> +
> +static int vadc_decimation_from_dt(u32 value)
> +{
> + if (!is_power_of_2(value) || value < VADC_DECIMATION_MIN ||
> + value > VADC_DECIMATION_MAX)
> + return -EINVAL;
> +
> + return __ffs64(value / VADC_DECIMATION_MIN);
> +}
> +
> +static int vadc_prescaling_from_dt(u32 num, u32 den)
> +{
> + unsigned int pre;
> +
> + for (pre = 0; pre < ARRAY_SIZE(vadc_prescale_ratios); pre++)
> + if (vadc_prescale_ratios[pre].num == num &&
> + vadc_prescale_ratios[pre].den == den)
> + break;
> +
> + if (pre == ARRAY_SIZE(vadc_prescale_ratios))
> + return -EINVAL;
> +
> + return pre;
> +}
> +
> +static int vadc_hw_settle_time_from_dt(u32 value)
> +{
> + if ((value <= 1000 && value % 100) || (value > 1000 && value % 2000))
> + return -EINVAL;
> +
> + if (value <= 1000)
> + value /= 100;
> + else
> + value = value / 2000 + 10;
> +
> + return value;
> +}
> +
> +static int vadc_avg_samples_from_dt(u32 value)
> +{
> + if (!is_power_of_2(value) || value > VADC_AVG_SAMPLES_MAX)
> + return -EINVAL;
> +
> + return __ffs64(value);
> +}
> +
> +static int vadc_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan, int *val, int *val2,
> + long mask)
> +{
> + struct vadc_priv *vadc = iio_priv(indio_dev);
> + struct vadc_channel_prop *prop;
> + u16 adc_code;
> + int ret;
> +
> + if (!vadc->are_ref_measured) {
> + ret = vadc_measure_ref_points(vadc);
> + if (ret)
> + return ret;
> +
> + vadc->are_ref_measured = true;
> + }
> +
> + if (mask == IIO_CHAN_INFO_PROCESSED || mask == IIO_CHAN_INFO_RAW) {
> + prop = &vadc->chan_props[chan->address];
> + ret = vadc_do_conversion(vadc, prop, &adc_code);
> + if (ret)
> + return ret;
> +
> + *val = vadc_calibrate(vadc, prop, adc_code);
> + }
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_PROCESSED:
> + if (chan->type != IIO_TEMP && chan->channel != VADC_DIE_TEMP)
> + return -EINVAL;
> +
> + /* 2mV/K, return milli Celsius */
> + *val /= 2;
> + *val -= KELVINMIL_CELSIUSMIL;
> + return IIO_VAL_INT;
> + case IIO_CHAN_INFO_RAW:
> + return IIO_VAL_INT;
> + case IIO_CHAN_INFO_SCALE:
> + *val = 0;
> + *val2 = 1000;
> + return IIO_VAL_INT_PLUS_MICRO;
> + default:
> + break;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int vadc_of_xlate(struct iio_dev *indio_dev,
> + const struct of_phandle_args *iiospec)
> +{
> + struct vadc_priv *vadc = iio_priv(indio_dev);
> + unsigned int i;
> +
> + for (i = 0; i < vadc->nchannels; i++)
> + if (vadc->iio_chans[i].channel == iiospec->args[0])
> + return i;
> +
> + return -EINVAL;
> +}
> +
> +static const struct iio_info vadc_info = {
> + .read_raw = vadc_read_raw,
> + .of_xlate = vadc_of_xlate,
> + .driver_module = THIS_MODULE,
> +};
> +
> +struct vadc_channels {
> + const char *datasheet_name;
> + unsigned int prescale_index;
> + enum iio_chan_type type;
> + long info_mask;
> +};
> +
> +#define VADC_CHAN(_dname, _type, _mask, _pre) \
> + [VADC_##_dname] = { \
> + .datasheet_name = __stringify(_dname), \
> + .prescale_index = _pre, \
> + .type = _type, \
> + .info_mask = _mask \
> + }, \
> +
> +#define VADC_CHAN_TEMP(_dname, _pre) \
> + VADC_CHAN(_dname, IIO_TEMP, BIT(IIO_CHAN_INFO_PROCESSED), _pre) \
> +
> +#define VADC_CHAN_VOLT(_dname, _pre) \
> + VADC_CHAN(_dname, IIO_VOLTAGE, \
> + BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), \
> + _pre) \
> +
> +/*
> + * The array represents all possible ADC channels found in the supported PMICs.
> + * Every index in the array is equal to the channel number per datasheet. The
> + * gaps in the array should be treated as reserved channels.
> + */
> +static const struct vadc_channels vadc_chans[] = {
> + VADC_CHAN_VOLT(USBIN, 4)
> + VADC_CHAN_VOLT(DCIN, 4)
> + VADC_CHAN_VOLT(VCHG_SNS, 3)
> + VADC_CHAN_VOLT(SPARE1_03, 1)
> + VADC_CHAN_VOLT(USB_ID_MV, 1)
> + VADC_CHAN_VOLT(VCOIN, 1)
> + VADC_CHAN_VOLT(VBAT_SNS, 1)
> + VADC_CHAN_VOLT(VSYS, 1)
> + VADC_CHAN_TEMP(DIE_TEMP, 0)
> + VADC_CHAN_VOLT(REF_625MV, 0)
> + VADC_CHAN_VOLT(REF_1250MV, 0)
> + VADC_CHAN_VOLT(CHG_TEMP, 0)
> + VADC_CHAN_VOLT(SPARE1, 0)
> + VADC_CHAN_VOLT(SPARE2, 0)
> + VADC_CHAN_VOLT(GND_REF, 0)
> + VADC_CHAN_VOLT(VDD_VADC, 0)
> +
> + VADC_CHAN_VOLT(P_MUX1_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX2_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX3_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX4_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX5_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX6_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX7_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX8_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX9_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX10_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX11_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX12_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX13_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX14_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX15_1_1, 0)
> + VADC_CHAN_VOLT(P_MUX16_1_1, 0)
> +
> + VADC_CHAN_VOLT(P_MUX1_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX2_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX3_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX4_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX5_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX6_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX7_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX8_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX9_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX10_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX11_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX12_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX13_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX14_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX15_1_3, 1)
> + VADC_CHAN_VOLT(P_MUX16_1_3, 1)
> +
> + VADC_CHAN_VOLT(LR_MUX1_BAT_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX2_BAT_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_XO_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX4_AMUX_THM1, 0)
> + VADC_CHAN_VOLT(LR_MUX5_AMUX_THM2, 0)
> + VADC_CHAN_VOLT(LR_MUX6_AMUX_THM3, 0)
> + VADC_CHAN_VOLT(LR_MUX7_HW_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX8_AMUX_THM4, 0)
> + VADC_CHAN_VOLT(LR_MUX9_AMUX_THM5, 0)
> + VADC_CHAN_VOLT(LR_MUX10_USB_ID, 0)
> + VADC_CHAN_VOLT(AMUX_PU1, 0)
> + VADC_CHAN_VOLT(AMUX_PU2, 0)
> + VADC_CHAN_VOLT(LR_MUX3_BUF_XO_THERM, 0)
> +
> + VADC_CHAN_VOLT(LR_MUX1_PU1_BAT_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX2_PU1_BAT_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_PU1_XO_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX4_PU1_AMUX_THM1, 0)
> + VADC_CHAN_VOLT(LR_MUX5_PU1_AMUX_THM2, 0)
> + VADC_CHAN_VOLT(LR_MUX6_PU1_AMUX_THM3, 0)
> + VADC_CHAN_VOLT(LR_MUX7_PU1_AMUX_HW_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX8_PU1_AMUX_THM4, 0)
> + VADC_CHAN_VOLT(LR_MUX9_PU1_AMUX_THM5, 0)
> + VADC_CHAN_VOLT(LR_MUX10_PU1_AMUX_USB_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_BUF_PU1_XO_THERM, 0)
> +
> + VADC_CHAN_VOLT(LR_MUX1_PU2_BAT_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX2_PU2_BAT_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_PU2_XO_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX4_PU2_AMUX_THM1, 0)
> + VADC_CHAN_VOLT(LR_MUX5_PU2_AMUX_THM2, 0)
> + VADC_CHAN_VOLT(LR_MUX6_PU2_AMUX_THM3, 0)
> + VADC_CHAN_VOLT(LR_MUX7_PU2_AMUX_HW_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX8_PU2_AMUX_THM4, 0)
> + VADC_CHAN_VOLT(LR_MUX9_PU2_AMUX_THM5, 0)
> + VADC_CHAN_VOLT(LR_MUX10_PU2_AMUX_USB_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_BUF_PU2_XO_THERM, 0)
> +
> + VADC_CHAN_VOLT(LR_MUX1_PU1_PU2_BAT_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX2_PU1_PU2_BAT_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_PU1_PU2_XO_THERM, 0)
> + VADC_CHAN_VOLT(LR_MUX4_PU1_PU2_AMUX_THM1, 0)
> + VADC_CHAN_VOLT(LR_MUX5_PU1_PU2_AMUX_THM2, 0)
> + VADC_CHAN_VOLT(LR_MUX6_PU1_PU2_AMUX_THM3, 0)
> + VADC_CHAN_VOLT(LR_MUX7_PU1_PU2_AMUX_HW_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX8_PU1_PU2_AMUX_THM4, 0)
> + VADC_CHAN_VOLT(LR_MUX9_PU1_PU2_AMUX_THM5, 0)
> + VADC_CHAN_VOLT(LR_MUX10_PU1_PU2_AMUX_USB_ID, 0)
> + VADC_CHAN_VOLT(LR_MUX3_BUF_PU1_PU2_XO_THERM, 0)
> +};
> +
> +static int vadc_get_dt_channel_data(struct device *dev,
> + struct vadc_channel_prop *prop,
> + struct device_node *node)
> +{
> + const char *name = node->name;
> + u32 chan, value, varr[2];
> + int ret;
> +
> + ret = of_property_read_u32(node, "reg", &chan);
> + if (ret) {
> + dev_err(dev, "invalid channel number %s\n", name);
> + return ret;
> + }
> +
> + if (chan > VADC_CHAN_MAX || chan < VADC_CHAN_MIN) {
> + dev_err(dev, "%s invalid channel number %d\n", name, chan);
> + return -EINVAL;
> + }
> +
> + /* the channel has DT description */
> + prop->channel = chan;
> +
> + ret = of_property_read_u32(node, "qcom,decimation", &value);
> + if (!ret) {
> + ret = vadc_decimation_from_dt(value);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid decimation %d\n",
> + chan, value);
> + return ret;
> + }
> + prop->decimation = ret;
> + } else {
> + prop->decimation = VADC_DEF_DECIMATION;
> + }
> +
> + ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2);
> + if (!ret) {
> + ret = vadc_prescaling_from_dt(varr[0], varr[1]);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid pre-scaling <%d %d>\n",
> + chan, varr[0], varr[1]);
> + return ret;
> + }
> + prop->prescale = ret;
> + } else {
> + prop->prescale = vadc_chans[prop->channel].prescale_index;
> + }
> +
> + ret = of_property_read_u32(node, "qcom,hw-settle-time", &value);
> + if (!ret) {
> + ret = vadc_hw_settle_time_from_dt(value);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid hw-settle-time %d us\n",
> + chan, value);
> + return ret;
> + }
> + prop->hw_settle_time = ret;
> + } else {
> + prop->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
> + }
> +
> + ret = of_property_read_u32(node, "qcom,avg-samples", &value);
> + if (!ret) {
> + ret = vadc_avg_samples_from_dt(value);
> + if (ret < 0) {
> + dev_err(dev, "%02x invalid avg-samples %d\n",
> + chan, value);
> + return ret;
> + }
> + prop->avg_samples = ret;
> + } else {
> + prop->avg_samples = VADC_DEF_AVG_SAMPLES;
> + }
> +
> + if (of_property_read_bool(node, "qcom,ratiometric"))
> + prop->calibration = VADC_CALIB_RATIOMETRIC;
> + else
> + prop->calibration = VADC_CALIB_ABSOLUTE;
> +
> + dev_dbg(dev, "%02x name %s\n", chan, name);
> +
> + return 0;
> +}
> +
> +static int vadc_get_dt_data(struct vadc_priv *vadc, struct device_node *node)
> +{
> + const struct vadc_channels *vadc_chan;
> + struct iio_chan_spec *iio_chan;
> + struct vadc_channel_prop prop;
> + struct device_node *child;
> + unsigned int index = 0;
> + int ret;
> +
> + vadc->nchannels = of_get_available_child_count(node);
> + if (!vadc->nchannels)
> + return -EINVAL;
> +
> + vadc->iio_chans = devm_kcalloc(vadc->dev, vadc->nchannels,
> + sizeof(*vadc->iio_chans), GFP_KERNEL);
> + if (!vadc->iio_chans)
> + return -ENOMEM;
> +
> + vadc->chan_props = devm_kcalloc(vadc->dev, vadc->nchannels,
> + sizeof(*vadc->chan_props), GFP_KERNEL);
> + if (!vadc->chan_props)
> + return -ENOMEM;
> +
> + iio_chan = vadc->iio_chans;
> +
> + for_each_available_child_of_node(node, child) {
> + ret = vadc_get_dt_channel_data(vadc->dev, &prop, child);
> + if (ret)
> + return ret;
> +
> + vadc->chan_props[index] = prop;
> +
> + vadc_chan = &vadc_chans[prop.channel];
> +
> + iio_chan->channel = prop.channel;
> + iio_chan->datasheet_name = vadc_chan->datasheet_name;
> + iio_chan->info_mask_separate = vadc_chan->info_mask;
> + iio_chan->type = vadc_chan->type;
> + iio_chan->indexed = 1;
> + iio_chan->address = index++;
> +
> + iio_chan++;
> + }
> +
> + /* These channels are mandatory, they are used as reference points */
> + if (!vadc_get_channel(vadc, VADC_REF_1250MV)) {
> + dev_err(vadc->dev, "Please define 1.25V channel\n");
> + return -ENODEV;
> + }
> +
> + if (!vadc_get_channel(vadc, VADC_REF_625MV)) {
> + dev_err(vadc->dev, "Please define 0.625V channel\n");
> + return -ENODEV;
> + }
> +
> + if (!vadc_get_channel(vadc, VADC_VDD_VADC)) {
> + dev_err(vadc->dev, "Please define VDD channel\n");
> + return -ENODEV;
> + }
> +
> + if (!vadc_get_channel(vadc, VADC_GND_REF)) {
> + dev_err(vadc->dev, "Please define GND channel\n");
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +static irqreturn_t vadc_isr(int irq, void *dev_id)
> +{
> + struct vadc_priv *vadc = dev_id;
> +
> + complete(&vadc->complete);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int vadc_check_revision(struct vadc_priv *vadc)
> +{
> + u8 val;
> + int ret;
> +
> + ret = vadc_read(vadc, VADC_PERPH_TYPE, &val);
> + if (ret)
> + return ret;
> +
> + if (val < VADC_PERPH_TYPE_ADC) {
> + dev_err(vadc->dev, "%d is not ADC\n", val);
> + return -ENODEV;
> + }
> +
> + ret = vadc_read(vadc, VADC_PERPH_SUBTYPE, &val);
> + if (ret)
> + return ret;
> +
> + if (val < VADC_PERPH_SUBTYPE_VADC) {
> + dev_err(vadc->dev, "%d is not VADC\n", val);
> + return -ENODEV;
> + }
> +
> + ret = vadc_read(vadc, VADC_REVISION2, &val);
> + if (ret)
> + return ret;
> +
> + if (val < VADC_REVISION2_SUPPORTED_VADC) {
> + dev_err(vadc->dev, "revision %d not supported\n", val);
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +static int vadc_probe(struct platform_device *pdev)
> +{
> + struct device_node *node = pdev->dev.of_node;
> + struct device *dev = &pdev->dev;
> + struct iio_dev *indio_dev;
> + struct vadc_priv *vadc;
> + struct regmap *regmap;
> + int ret, irq_eoc;
> + u32 res;
Since vadc->base is u16, shouldn't res be u16 as well? Also think about naming it reg, as this is the property name in DT.
> +
> + regmap = dev_get_regmap(dev->parent, NULL);
> + if (!regmap)
> + return -ENODEV;
> +
> + ret = of_property_read_u32(node, "reg", &res);
For u16, there would be of_property_read_u16().
> + if (ret < 0)
> + return -ENODEV;
Just return ret here?
> +
> + indio_dev = devm_iio_device_alloc(dev, sizeof(*vadc));
> + if (!indio_dev)
> + return -ENOMEM;
> +
> + vadc = iio_priv(indio_dev);
> + vadc->regmap = regmap;
> + vadc->dev = dev;
> + vadc->base = res;
> + vadc->are_ref_measured = false;
> + init_completion(&vadc->complete);
> +
> + ret = vadc_check_revision(vadc);
> + if (ret)
> + return ret;
> +
> + ret = vadc_get_dt_data(vadc, node);
> + if (ret)
> + return ret;
> +
> + irq_eoc = platform_get_irq(pdev, 0);
> + if (irq_eoc < 0) {
> + if (irq_eoc == -EPROBE_DEFER || irq_eoc == -EINVAL)
> + return irq_eoc;
> + vadc->poll_eoc = true;
> + } else {
> + ret = devm_request_irq(dev, irq_eoc, vadc_isr, 0,
> + "spmi-vadc", vadc);
> + if (ret)
> + return ret;
> + }
> +
> + ret = vadc_reset(vadc);
> + if (ret) {
> + dev_err(dev, "reset failed\n");
> + return ret;
> + }
> +
> + indio_dev->dev.parent = dev;
> + indio_dev->dev.of_node = node;
> + indio_dev->name = pdev->name;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + indio_dev->info = &vadc_info;
> + indio_dev->channels = vadc->iio_chans;
> + indio_dev->num_channels = vadc->nchannels;
> +
> + return devm_iio_device_register(dev, indio_dev);
> +}
> +
> +static const struct of_device_id vadc_match_table[] = {
> + { .compatible = "qcom,spmi-vadc" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, vadc_match_table);
> +
> +static struct platform_driver vadc_driver = {
> + .driver = {
> + .name = "qcom-spmi-vadc",
> + .of_match_table = vadc_match_table,
> + },
> + .probe = vadc_probe,
> +};
> +module_platform_driver(vadc_driver);
> +
> +MODULE_ALIAS("platform:qcom-spmi-vadc");
> +MODULE_DESCRIPTION("Qualcomm SPMI PMIC voltage ADC driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_AUTHOR("Stanimir Varbanov <[email protected]>");
> +MODULE_AUTHOR("Ivan T. Ivanov <[email protected]>");
>
Hi Hartmut,
On Mon, 2014-11-10 at 22:11 +0100, Hartmut Knaack wrote:
> Ivan T. Ivanov schrieb am 03.11.2014 16:24:
> > From: Stanimir Varbanov <[email protected]>
> >
> > The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
> > 15 bits resolution and register space inside PMIC accessible across
> > SPMI bus.
> >
> > The vadc driver registers itself through IIO interface.
> Reviewing again, I got the feeling that due to the complexity of adc reads (writing to register
> to start conversion, waiting a decent time for the conversion to complete, reading the result),
> it would be beneficial to use a mutex in vadc_read_raw or its depending functions.
Hm, yes, but there is such a nice info_exist_lock :-) in core functions,
which in practice serve the same purpose.
> Also, I would want to double-check that the CPU in this type of chips is little endian.
Yes, it is.
> Besides that, a few minor issues inline.
> > +static int vadc_probe(struct platform_device *pdev)
> > +{
> > + struct device_node *node = pdev->dev.of_node;
> > + struct device *dev = &pdev->dev;
> > + struct iio_dev *indio_dev;
> > + struct vadc_priv *vadc;
> > + struct regmap *regmap;
> > + int ret, irq_eoc;
> > + u32 res;
> Since vadc->base is u16, shouldn't res be u16 as well? Also think about naming it reg, as this is
> the property name in DT.
Yes, but #address-cells for the node is 1, so I would like to keep it 32 bits.
> > +
> > + regmap = dev_get_regmap(dev->parent, NULL);
> > + if (!regmap)
> > + return -ENODEV;
> > +
> > + ret = of_property_read_u32(node, "reg", &res);
> For u16, there would be of_property_read_u16().
> > + if (ret < 0)
> > + return -ENODEV;
> Just return ret here?
I am usually trying to follow these recommendations[1]. In practice driver
core cares only for EPROBE_DEFER, ENODEV and ENXIO, while of_property_read_u32()
can return ENODATA and EOVERFLOW, which did't not make sense for the core.
Thank you,
Ivan
[1] http://www.gossamer-threads.com/lists/linux/kernel/1010603
Ivan T. Ivanov schrieb am 11.11.2014 09:21:
> Hi Hartmut,
>
> On Mon, 2014-11-10 at 22:11 +0100, Hartmut Knaack wrote:
>> Ivan T. Ivanov schrieb am 03.11.2014 16:24:
>>> From: Stanimir Varbanov <[email protected]>
>>>
>>> The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
>>> 15 bits resolution and register space inside PMIC accessible across
>>> SPMI bus.
>>>
>>> The vadc driver registers itself through IIO interface.
>> Reviewing again, I got the feeling that due to the complexity of adc reads (writing to register
>> to start conversion, waiting a decent time for the conversion to complete, reading the result),
>> it would be beneficial to use a mutex in vadc_read_raw or its depending functions.
>
> Hm, yes, but there is such a nice info_exist_lock :-) in core functions,
> which in practice serve the same purpose.
I seem to miss that. Please point me in the right direction.
>
>> Also, I would want to double-check that the CPU in this type of chips is little endian.
>
> Yes, it is.
>
>> Besides that, a few minor issues inline.
>
>>> +static int vadc_probe(struct platform_device *pdev)
>>> +{
>>> + struct device_node *node = pdev->dev.of_node;
>>> + struct device *dev = &pdev->dev;
>>> + struct iio_dev *indio_dev;
>>> + struct vadc_priv *vadc;
>>> + struct regmap *regmap;
>>> + int ret, irq_eoc;
>>> + u32 res;
>> Since vadc->base is u16, shouldn't res be u16 as well? Also think about naming it reg, as this is
>> the property name in DT.
>
> Yes, but #address-cells for the node is 1, so I would like to keep it 32 bits.
>
>>> +
>>> + regmap = dev_get_regmap(dev->parent, NULL);
>>> + if (!regmap)
>>> + return -ENODEV;
>>> +
>>> + ret = of_property_read_u32(node, "reg", &res);
>> For u16, there would be of_property_read_u16().
>>> + if (ret < 0)
>>> + return -ENODEV;
>> Just return ret here?
>
> I am usually trying to follow these recommendations[1]. In practice driver
> core cares only for EPROBE_DEFER, ENODEV and ENXIO, while of_property_read_u32()
> can return ENODATA and EOVERFLOW, which did't not make sense for the core.
Please point me in the right direction on this one, too. It is pretty common to pass error codes up, as it is also mentioned in [1].
Yet, this thread in [1] seems more like a draft to me, as Greg K-H wrote in the end: "Fair enough, care to respin this and send it out to me for review?"
>
> Thank you,
> Ivan
>
> [1] http://www.gossamer-threads.com/lists/linux/kernel/1010603
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
On Tue, 2014-11-11 at 23:39 +0100, Hartmut Knaack wrote:
> Ivan T. Ivanov schrieb am 11.11.2014 09:21:
> > Hi Hartmut,
> >
> > On Mon, 2014-11-10 at 22:11 +0100, Hartmut Knaack wrote:
> > > Ivan T. Ivanov schrieb am 03.11.2014 16:24:
> > > > From: Stanimir Varbanov <[email protected]>
> > > >
> > > > The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
> > > > 15 bits resolution and register space inside PMIC accessible across
> > > > SPMI bus.
> > > >
> > > > The vadc driver registers itself through IIO interface.
> > > Reviewing again, I got the feeling that due to the complexity of adc reads (writing to
> > > register
> > > to start conversion, waiting a decent time for the conversion to complete, reading the
> > > result),
> > > it would be beneficial to use a mutex in vadc_read_raw or its depending functions.
> >
> > Hm, yes, but there is such a nice info_exist_lock :-) in core functions,
> > which in practice serve the same purpose.
> I seem to miss that. Please point me in the right direction.
I am referring to info_exist_lock mutex part of struct iio_dev.
It protects all operations inkern.c, no?
> > >
> > > > +
> > > > + ret = of_property_read_u32(node, "reg", &res);
> > > For u16, there would be of_property_read_u16().
> > > > + if (ret < 0)
> > > > + return -ENODEV;
> > > Just return ret here?
> >
> > I am usually trying to follow these recommendations[1]. In practice driver
> > core cares only for EPROBE_DEFER, ENODEV and ENXIO, while of_property_read_u32()
> > can return ENODATA and EOVERFLOW, which did't not make sense for the core.
> Please point me in the right direction on this one, too. It is pretty common to pass error codes
> up, as it is also mentioned in [1].
Yes, I know that is common to just pass error codes up, but in this case it did't
make too much sense, I think. Also take a look at realy_probe() and line 343.
> Yet, this thread in [1] seems more like a draft to me, as Greg K-H wrote in the end: "Fair
> enough, care to respin this and send it out to me for review?"
Yes, but it make sense to me.
Regards,
Ivan
Ivan T. Ivanov schrieb am 12.11.2014 09:55:
>
> On Tue, 2014-11-11 at 23:39 +0100, Hartmut Knaack wrote:
>> Ivan T. Ivanov schrieb am 11.11.2014 09:21:
>>> Hi Hartmut,
>>>
>>> On Mon, 2014-11-10 at 22:11 +0100, Hartmut Knaack wrote:
>>>> Ivan T. Ivanov schrieb am 03.11.2014 16:24:
>>>>> From: Stanimir Varbanov <[email protected]>
>>>>>
>>>>> The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
>>>>> 15 bits resolution and register space inside PMIC accessible across
>>>>> SPMI bus.
>>>>>
>>>>> The vadc driver registers itself through IIO interface.
>>>> Reviewing again, I got the feeling that due to the complexity of adc reads (writing to
>>>> register
>>>> to start conversion, waiting a decent time for the conversion to complete, reading the
>>>> result),
>>>> it would be beneficial to use a mutex in vadc_read_raw or its depending functions.
>>>
>>> Hm, yes, but there is such a nice info_exist_lock :-) in core functions,
>>> which in practice serve the same purpose.
>> I seem to miss that. Please point me in the right direction.
>
> I am referring to info_exist_lock mutex part of struct iio_dev.
> It protects all operations inkern.c, no?
>
Good point, thanks for helping me there.
>>>>
>>>>> +
>>>>> + ret = of_property_read_u32(node, "reg", &res);
>>>> For u16, there would be of_property_read_u16().
>>>>> + if (ret < 0)
>>>>> + return -ENODEV;
>>>> Just return ret here?
>>>
>>> I am usually trying to follow these recommendations[1]. In practice driver
>>> core cares only for EPROBE_DEFER, ENODEV and ENXIO, while of_property_read_u32()
>>> can return ENODATA and EOVERFLOW, which did't not make sense for the core.
>> Please point me in the right direction on this one, too. It is pretty common to pass error codes
>> up, as it is also mentioned in [1].
>
> Yes, I know that is common to just pass error codes up, but in this case it did't
> make too much sense, I think. Also take a look at realy_probe() and line 343.
This doesn't convince me. Actually, within the probe_failed part, it just doesn't care about ENODEV and ENXIO as long as debug messages are disabled (which apart from some developers, is default for the vast majority of devices). For all other error codes, it will at least print an info or warning about what's going wrong (and that can be a lot of help for debugging).
>
>> Yet, this thread in [1] seems more like a draft to me, as Greg K-H wrote in the end: "Fair
>> enough, care to respin this and send it out to me for review?"
>
>
>
> Yes, but it make sense to me.
>
> Regards,
> Ivan
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
On Mon, 2014-11-17 at 23:12 +0100, Hartmut Knaack wrote:
> Ivan T. Ivanov schrieb am 12.11.2014 09:55:
> > On Tue, 2014-11-11 at 23:39 +0100, Hartmut Knaack wrote:
> > > Ivan T. Ivanov schrieb am 11.11.2014 09:21:
> > > > Hi Hartmut,
> > > >
> > > > On Mon, 2014-11-10 at 22:11 +0100, Hartmut Knaack wrote:
> > > > > Ivan T. Ivanov schrieb am 03.11.2014 16:24:
> > > > > > From: Stanimir Varbanov <[email protected]>
> > > > > >
> > > > > > The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
> > > > > > 15 bits resolution and register space inside PMIC accessible across
> > > > > > SPMI bus.
> > > > > >
> > > > > > The vadc driver registers itself through IIO interface.
> > > > > Reviewing again, I got the feeling that due to the complexity of adc reads (writing to
> > > > > register
> > > > > to start conversion, waiting a decent time for the conversion to complete, reading the
> > > > > result),
> > > > > it would be beneficial to use a mutex in vadc_read_raw or its depending functions.
> > > >
> > > > Hm, yes, but there is such a nice info_exist_lock :-) in core functions,
> > > > which in practice serve the same purpose.
> > > I seem to miss that. Please point me in the right direction.
> >
> > I am referring to info_exist_lock mutex part of struct iio_dev.
> > It protects all operations inkern.c, no?
> >
> Good point, thanks for helping me there.
I was wondering, is there a plan to improve this part of the code?
I mean to remove per device lock and use something like try_module_get(),
when clients are acquiring reference to iio channel?
> > > > > > +
> > > > > > + ret = of_property_read_u32(node, "reg", &res);
> > > > > For u16, there would be of_property_read_u16().
> > > > > > + if (ret < 0)
> > > > > > + return -ENODEV;
> > > > > Just return ret here?
> > > >
> > > > I am usually trying to follow these recommendations[1]. In practice driver
> > > > core cares only for EPROBE_DEFER, ENODEV and ENXIO, while of_property_read_u32()
> > > > can return ENODATA and EOVERFLOW, which did't not make sense for the core.
> > > Please point me in the right direction on this one, too. It is pretty common to pass error
> > > codes
> > > up, as it is also mentioned in [1].
> >
> > Yes, I know that is common to just pass error codes up, but in this case it did't
> > make too much sense, I think. Also take a look at realy_probe() and line 343.
> This doesn't convince me. Actually, within the probe_failed part, it just doesn't care about
> ENODEV and ENXIO as long as debug messages are disabled (which apart from some developers, is
> default for the vast majority of devices). For all other error codes, it will at least print an
> info or warning about what's going wrong (and that can be a lot of help for debugging).
Well, if you insist... will change it.
Thanks,
Ivan
On 18/11/14 08:23, Ivan T. Ivanov wrote:
>
> On Mon, 2014-11-17 at 23:12 +0100, Hartmut Knaack wrote:
>> Ivan T. Ivanov schrieb am 12.11.2014 09:55:
>>> On Tue, 2014-11-11 at 23:39 +0100, Hartmut Knaack wrote:
>>>> Ivan T. Ivanov schrieb am 11.11.2014 09:21:
>>>>> Hi Hartmut,
>>>>>
>>>>> On Mon, 2014-11-10 at 22:11 +0100, Hartmut Knaack wrote:
>>>>>> Ivan T. Ivanov schrieb am 03.11.2014 16:24:
>>>>>>> From: Stanimir Varbanov <[email protected]>
>>>>>>>
>>>>>>> The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
>>>>>>> 15 bits resolution and register space inside PMIC accessible across
>>>>>>> SPMI bus.
>>>>>>>
>>>>>>> The vadc driver registers itself through IIO interface.
>>>>>> Reviewing again, I got the feeling that due to the complexity of adc reads (writing to
>>>>>> register
>>>>>> to start conversion, waiting a decent time for the conversion to complete, reading the
>>>>>> result),
>>>>>> it would be beneficial to use a mutex in vadc_read_raw or its depending functions.
>>>>>
>>>>> Hm, yes, but there is such a nice info_exist_lock :-) in core functions,
>>>>> which in practice serve the same purpose.
>>>> I seem to miss that. Please point me in the right direction.
>>>
>>> I am referring to info_exist_lock mutex part of struct iio_dev.
>>> It protects all operations inkern.c, no?
>>>
>> Good point, thanks for helping me there.
>
> I was wondering, is there a plan to improve this part of the code?
No one is working on it that I know of. All patches welcome!
> I mean to remove per device lock and use something like try_module_get(),
> when clients are acquiring reference to iio channel?
That might indeed provide a more elegant solution...
(the things I don't know exist never fail to surprise me!)
>
>>>>>>> +
>>>>>>> + ret = of_property_read_u32(node, "reg", &res);
>>>>>> For u16, there would be of_property_read_u16().
>>>>>>> + if (ret < 0)
>>>>>>> + return -ENODEV;
>>>>>> Just return ret here?
>>>>>
>>>>> I am usually trying to follow these recommendations[1]. In practice driver
>>>>> core cares only for EPROBE_DEFER, ENODEV and ENXIO, while of_property_read_u32()
>>>>> can return ENODATA and EOVERFLOW, which did't not make sense for the core.
>>>> Please point me in the right direction on this one, too. It is pretty common to pass error
>>>> codes
>>>> up, as it is also mentioned in [1].
>>>
>>> Yes, I know that is common to just pass error codes up, but in this case it did't
>>> make too much sense, I think. Also take a look at realy_probe() and line 343.
>> This doesn't convince me. Actually, within the probe_failed part, it just doesn't care about
>> ENODEV and ENXIO as long as debug messages are disabled (which apart from some developers, is
>> default for the vast majority of devices). For all other error codes, it will at least print an
>> info or warning about what's going wrong (and that can be a lot of help for debugging).
>
> Well, if you insist... will change it.
>
> Thanks,
> Ivan
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>