2014-11-22 15:24:21

by Beniamino Galvani

[permalink] [raw]
Subject: [PATCH v3 0/4] spi: Add support for Amlogic Meson SPIFC

Hi,

this patchset adds a driver for the SPIFC (SPI flash controller)
available in Amlogic Meson6 and Meson8 SoCs. The driver has been
tested on a Meson8 based device to communicate with a Macronix
mx25l1606e serial flash.

Changes since v2 [ https://lkml.org/lkml/2014/11/17/669 ]:
- introduce spi_transfer_is_last() helper instead of using a flag
in spi_transfer structure
- rebase DTS patch on arm-soc

Changes since v1 [ https://lkml.org/lkml/2014/11/9/35 ]:
- decrease busy wait timeout
- remove check on xfer->speed_hz value in meson_spifc_transfer_one()
- implement transfer_one() instead of transfer_one_message()
- remove useless memset of devdata
- use fixed regmap config
- implement PM operations
- don't set master->bus_num
- allow modular build of the driver

Beniamino Galvani (4):
spi: core: Add spi_transfer_is_last() helper
spi: meson: Add device tree bindings documentation for SPIFC
spi: meson: Add support for Amlogic Meson SPIFC
ARM: dts: meson: add node for SPIFC

.../devicetree/bindings/spi/spi-meson.txt | 22 +
arch/arm/boot/dts/meson.dtsi | 9 +
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-meson-spifc.c | 462 +++++++++++++++++++++
include/linux/spi/spi.h | 6 +
6 files changed, 507 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spi/spi-meson.txt
create mode 100644 drivers/spi/spi-meson-spifc.c

--
1.9.1


2014-11-22 15:24:27

by Beniamino Galvani

[permalink] [raw]
Subject: [PATCH v3 2/4] spi: meson: Add device tree bindings documentation for SPIFC

This adds documentation of device tree bindings for the Amlogic Meson
SPIFC (SPI Flash Controller).

Signed-off-by: Beniamino Galvani <[email protected]>
---
.../devicetree/bindings/spi/spi-meson.txt | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spi/spi-meson.txt

diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt
new file mode 100644
index 0000000..bb52a86
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-meson.txt
@@ -0,0 +1,22 @@
+Amlogic Meson SPI controllers
+
+* SPIFC (SPI Flash Controller)
+
+The Meson SPIFC is a controller optimized for communication with SPI
+NOR memories, without DMA support and a 64-byte unified transmit /
+receive buffer.
+
+Required properties:
+ - compatible: should be "amlogic,meson6-spifc"
+ - reg: physical base address and length of the controller registers
+ - clocks: phandle of the input clock for the baud rate generator
+ - #address-cells: should be 1
+ - #size-cells: should be 0
+
+ spi@c1108c80 {
+ compatible = "amlogic,meson6-spifc";
+ reg = <0xc1108c80 0x80>;
+ clocks = <&clk81>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
--
1.9.1

2014-11-22 15:24:30

by Beniamino Galvani

[permalink] [raw]
Subject: [PATCH v3 3/4] spi: meson: Add support for Amlogic Meson SPIFC

This is a driver for the Amlogic Meson SPIFC (SPI flash controller),
which is one of the two SPI controllers available on the SoC. It
doesn't support DMA and has a 64-byte unified transmit/receive buffer.

The device is optimized for interfacing with SPI NOR memories and
allows the execution of standard operations such as read, page
program, sector erase, etc. in a simplified way, toggling a bit in a
dedicated register. The driver doesn't use those predefined commands
and relies only on custom transfers.

Signed-off-by: Beniamino Galvani <[email protected]>
---
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-meson-spifc.c | 462 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 470 insertions(+)
create mode 100644 drivers/spi/spi-meson-spifc.c

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 98de207..0373c37 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -308,6 +308,13 @@ config SPI_FSL_ESPI
From MPC8536, 85xx platform uses the controller, and all P10xx,
P20xx, P30xx,P40xx, P50xx uses this controller.

+config SPI_MESON_SPIFC
+ tristate "Amlogic Meson SPIFC controller"
+ depends on ARCH_MESON || COMPILE_TEST
+ help
+ This enables master mode support for the SPIFC (SPI flash
+ controller) available in Amlogic Meson SoCs.
+
config SPI_OC_TINY
tristate "OpenCores tiny SPI"
depends on GPIOLIB
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 37dc2e7..6b9d2ac 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_SPI_GPIO) += spi-gpio.o
obj-$(CONFIG_SPI_IMG_SPFI) += spi-img-spfi.o
obj-$(CONFIG_SPI_IMX) += spi-imx.o
obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o
+obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o
obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mpc512x-psc.o
obj-$(CONFIG_SPI_MPC52xx_PSC) += spi-mpc52xx-psc.o
obj-$(CONFIG_SPI_MPC52xx) += spi-mpc52xx.o
diff --git a/drivers/spi/spi-meson-spifc.c b/drivers/spi/spi-meson-spifc.c
new file mode 100644
index 0000000..f536476
--- /dev/null
+++ b/drivers/spi/spi-meson-spifc.c
@@ -0,0 +1,462 @@
+/*
+ * Driver for Amlogic Meson SPI flash controller (SPIFC)
+ *
+ * Copyright (C) 2014 Beniamino Galvani <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+#include <linux/types.h>
+
+/* register map */
+#define REG_CMD 0x00
+#define REG_ADDR 0x04
+#define REG_CTRL 0x08
+#define REG_CTRL1 0x0c
+#define REG_STATUS 0x10
+#define REG_CTRL2 0x14
+#define REG_CLOCK 0x18
+#define REG_USER 0x1c
+#define REG_USER1 0x20
+#define REG_USER2 0x24
+#define REG_USER3 0x28
+#define REG_USER4 0x2c
+#define REG_SLAVE 0x30
+#define REG_SLAVE1 0x34
+#define REG_SLAVE2 0x38
+#define REG_SLAVE3 0x3c
+#define REG_C0 0x40
+#define REG_B8 0x60
+#define REG_MAX 0x7c
+
+/* register fields */
+#define CMD_USER BIT(18)
+#define CTRL_ENABLE_AHB BIT(17)
+#define CLOCK_SOURCE BIT(31)
+#define CLOCK_DIV_SHIFT 12
+#define CLOCK_DIV_MASK (0x3f << CLOCK_DIV_SHIFT)
+#define CLOCK_CNT_HIGH_SHIFT 6
+#define CLOCK_CNT_HIGH_MASK (0x3f << CLOCK_CNT_HIGH_SHIFT)
+#define CLOCK_CNT_LOW_SHIFT 0
+#define CLOCK_CNT_LOW_MASK (0x3f << CLOCK_CNT_LOW_SHIFT)
+#define USER_DIN_EN_MS BIT(0)
+#define USER_CMP_MODE BIT(2)
+#define USER_UC_DOUT_SEL BIT(27)
+#define USER_UC_DIN_SEL BIT(28)
+#define USER_UC_MASK ((BIT(5) - 1) << 27)
+#define USER1_BN_UC_DOUT_SHIFT 17
+#define USER1_BN_UC_DOUT_MASK (0xff << 16)
+#define USER1_BN_UC_DIN_SHIFT 8
+#define USER1_BN_UC_DIN_MASK (0xff << 8)
+#define USER4_CS_ACT BIT(30)
+#define SLAVE_TRST_DONE BIT(4)
+#define SLAVE_OP_MODE BIT(30)
+#define SLAVE_SW_RST BIT(31)
+
+#define SPIFC_BUFFER_SIZE 64
+
+/**
+ * struct meson_spifc
+ * @master: the SPI master
+ * @regmap: regmap for device registers
+ * @clk: input clock of the built-in baud rate generator
+ * @device: the device structure
+ */
+struct meson_spifc {
+ struct spi_master *master;
+ struct regmap *regmap;
+ struct clk *clk;
+ struct device *dev;
+};
+
+static struct regmap_config spifc_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = REG_MAX,
+};
+
+/**
+ * meson_spifc_wait_ready() - wait for the current operation to terminate
+ * @spifc: the Meson SPI device
+ * Return: 0 on success, a negative value on error
+ */
+static int meson_spifc_wait_ready(struct meson_spifc *spifc)
+{
+ unsigned long deadline = jiffies + msecs_to_jiffies(5);
+ u32 data;
+
+ do {
+ regmap_read(spifc->regmap, REG_SLAVE, &data);
+ if (data & SLAVE_TRST_DONE)
+ return 0;
+ cond_resched();
+ } while (!time_after(jiffies, deadline));
+
+ return -ETIMEDOUT;
+}
+
+/**
+ * meson_spifc_drain_buffer() - copy data from device buffer to memory
+ * @spifc: the Meson SPI device
+ * @buf: the destination buffer
+ * @len: number of bytes to copy
+ */
+static void meson_spifc_drain_buffer(struct meson_spifc *spifc, u8 *buf,
+ int len)
+{
+ u32 data;
+ int i = 0;
+
+ while (i < len) {
+ regmap_read(spifc->regmap, REG_C0 + i, &data);
+
+ if (len - i >= 4) {
+ *((u32 *)buf) = data;
+ buf += 4;
+ } else {
+ memcpy(buf, &data, len - i);
+ break;
+ }
+ i += 4;
+ }
+}
+
+/**
+ * meson_spifc_fill_buffer() - copy data from memory to device buffer
+ * @spifc: the Meson SPI device
+ * @buf: the source buffer
+ * @len: number of bytes to copy
+ */
+static void meson_spifc_fill_buffer(struct meson_spifc *spifc, const u8 *buf,
+ int len)
+{
+ u32 data;
+ int i = 0;
+
+ while (i < len) {
+ if (len - i >= 4)
+ data = *(u32 *)buf;
+ else
+ memcpy(&data, buf, len - i);
+
+ regmap_write(spifc->regmap, REG_C0 + i, data);
+
+ buf += 4;
+ i += 4;
+ }
+}
+
+/**
+ * meson_spifc_setup_speed() - program the clock divider
+ * @spifc: the Meson SPI device
+ * @speed: desired speed in Hz
+ */
+void meson_spifc_setup_speed(struct meson_spifc *spifc, u32 speed)
+{
+ unsigned long parent, value;
+ int n;
+
+ parent = clk_get_rate(spifc->clk);
+ n = max_t(int, parent / speed - 1, 1);
+
+ dev_dbg(spifc->dev, "parent %lu, speed %u, n %d\n", parent,
+ speed, n);
+
+ value = (n << CLOCK_DIV_SHIFT) & CLOCK_DIV_MASK;
+ value |= (n << CLOCK_CNT_LOW_SHIFT) & CLOCK_CNT_LOW_MASK;
+ value |= (((n + 1) / 2 - 1) << CLOCK_CNT_HIGH_SHIFT) &
+ CLOCK_CNT_HIGH_MASK;
+
+ regmap_write(spifc->regmap, REG_CLOCK, value);
+}
+
+/**
+ * meson_spifc_txrx() - transfer a chunk of data
+ * @spifc: the Meson SPI device
+ * @xfer: the current SPI transfer
+ * @offset: offset of the data to transfer
+ * @len: length of the data to transfer
+ * @last_xfer: whether this is the last transfer of the message
+ * @last_chunk: whether this is the last chunk of the transfer
+ * Return: 0 on success, a negative value on error
+ */
+static int meson_spifc_txrx(struct meson_spifc *spifc,
+ struct spi_transfer *xfer,
+ int offset, int len, bool last_xfer,
+ bool last_chunk)
+{
+ bool keep_cs = true;
+ int ret;
+
+ if (xfer->tx_buf)
+ meson_spifc_fill_buffer(spifc, xfer->tx_buf + offset, len);
+
+ /* enable DOUT stage */
+ regmap_update_bits(spifc->regmap, REG_USER, USER_UC_MASK,
+ USER_UC_DOUT_SEL);
+ regmap_write(spifc->regmap, REG_USER1,
+ (8 * len - 1) << USER1_BN_UC_DOUT_SHIFT);
+
+ /* enable data input during DOUT */
+ regmap_update_bits(spifc->regmap, REG_USER, USER_DIN_EN_MS,
+ USER_DIN_EN_MS);
+
+ if (last_chunk) {
+ if (last_xfer)
+ keep_cs = xfer->cs_change;
+ else
+ keep_cs = !xfer->cs_change;
+ }
+
+ regmap_update_bits(spifc->regmap, REG_USER4, USER4_CS_ACT,
+ keep_cs ? USER4_CS_ACT : 0);
+
+ /* clear transition done bit */
+ regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_TRST_DONE, 0);
+ /* start transfer */
+ regmap_update_bits(spifc->regmap, REG_CMD, CMD_USER, CMD_USER);
+
+ ret = meson_spifc_wait_ready(spifc);
+
+ if (!ret && xfer->rx_buf)
+ meson_spifc_drain_buffer(spifc, xfer->rx_buf + offset, len);
+
+ return ret;
+}
+
+/**
+ * meson_spifc_transfer_one() - perform a single transfer
+ * @master: the SPI master
+ * @spi: the SPI device
+ * @xfer: the current SPI transfer
+ * Return: 0 on success, a negative value on error
+ */
+static int meson_spifc_transfer_one(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *xfer)
+{
+ struct meson_spifc *spifc = spi_master_get_devdata(master);
+ int len, done = 0, ret = 0;
+
+ meson_spifc_setup_speed(spifc, xfer->speed_hz);
+
+ regmap_update_bits(spifc->regmap, REG_CTRL, CTRL_ENABLE_AHB, 0);
+
+ while (done < xfer->len && !ret) {
+ len = min_t(int, xfer->len - done, SPIFC_BUFFER_SIZE);
+ ret = meson_spifc_txrx(spifc, xfer, done, len,
+ spi_transfer_is_last(master, xfer),
+ done + len >= xfer->len);
+ done += len;
+ }
+
+ regmap_update_bits(spifc->regmap, REG_CTRL, CTRL_ENABLE_AHB,
+ CTRL_ENABLE_AHB);
+
+ return ret;
+}
+
+/**
+ * meson_spifc_hw_init() - reset and initialize the SPI controller
+ * @spifc: the Meson SPI device
+ */
+static void meson_spifc_hw_init(struct meson_spifc *spifc)
+{
+ /* reset device */
+ regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_SW_RST,
+ SLAVE_SW_RST);
+ /* disable compatible mode */
+ regmap_update_bits(spifc->regmap, REG_USER, USER_CMP_MODE, 0);
+ /* set master mode */
+ regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_OP_MODE, 0);
+}
+
+static int meson_spifc_probe(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct meson_spifc *spifc;
+ struct resource *res;
+ void __iomem *base;
+ unsigned int rate;
+ int ret = 0;
+
+ master = spi_alloc_master(&pdev->dev, sizeof(struct meson_spifc));
+ if (!master)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, master);
+
+ spifc = spi_master_get_devdata(master);
+ spifc->dev = &pdev->dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(spifc->dev, res);
+ if (IS_ERR(base)) {
+ ret = PTR_ERR(base);
+ goto out_err;
+ }
+
+ spifc->regmap = devm_regmap_init_mmio(spifc->dev, base,
+ &spifc_regmap_config);
+ if (IS_ERR(spifc->regmap)) {
+ ret = PTR_ERR(spifc->regmap);
+ goto out_err;
+ }
+
+ spifc->clk = devm_clk_get(spifc->dev, NULL);
+ if (IS_ERR(spifc->clk)) {
+ dev_err(spifc->dev, "missing clock\n");
+ ret = PTR_ERR(spifc->clk);
+ goto out_err;
+ }
+
+ ret = clk_prepare_enable(spifc->clk);
+ if (ret) {
+ dev_err(spifc->dev, "can't prepare clock\n");
+ goto out_err;
+ }
+
+ rate = clk_get_rate(spifc->clk);
+
+ master->num_chipselect = 1;
+ master->dev.of_node = pdev->dev.of_node;
+ master->bits_per_word_mask = SPI_BPW_MASK(8);
+ master->auto_runtime_pm = true;
+ master->transfer_one = meson_spifc_transfer_one;
+ master->min_speed_hz = rate >> 6;
+ master->max_speed_hz = rate >> 1;
+
+ meson_spifc_hw_init(spifc);
+
+ pm_runtime_set_active(spifc->dev);
+ pm_runtime_enable(spifc->dev);
+
+ ret = devm_spi_register_master(spifc->dev, master);
+ if (ret) {
+ dev_err(spifc->dev, "failed to register spi master\n");
+ goto out_clk;
+ }
+
+ return 0;
+out_clk:
+ clk_disable_unprepare(spifc->clk);
+out_err:
+ spi_master_put(master);
+ return ret;
+}
+
+static int meson_spifc_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct meson_spifc *spifc = spi_master_get_devdata(master);
+
+ pm_runtime_get_sync(&pdev->dev);
+ clk_disable_unprepare(spifc->clk);
+ pm_runtime_disable(&pdev->dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int meson_spifc_suspend(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct meson_spifc *spifc = spi_master_get_devdata(master);
+ int ret;
+
+ ret = spi_master_suspend(master);
+ if (ret)
+ return ret;
+
+ if (!pm_runtime_suspended(dev))
+ clk_disable_unprepare(spifc->clk);
+
+ return 0;
+}
+
+static int meson_spifc_resume(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct meson_spifc *spifc = spi_master_get_devdata(master);
+ int ret;
+
+ if (!pm_runtime_suspended(dev)) {
+ ret = clk_prepare_enable(spifc->clk);
+ if (ret)
+ return ret;
+ }
+
+ meson_spifc_hw_init(spifc);
+
+ ret = spi_master_resume(master);
+ if (ret)
+ clk_disable_unprepare(spifc->clk);
+
+ return ret;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+#ifdef CONFIG_PM_RUNTIME
+static int meson_spifc_runtime_suspend(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct meson_spifc *spifc = spi_master_get_devdata(master);
+
+ clk_disable_unprepare(spifc->clk);
+
+ return 0;
+}
+
+static int meson_spifc_runtime_resume(struct device *dev)
+{
+ struct spi_master *master = dev_get_drvdata(dev);
+ struct meson_spifc *spifc = spi_master_get_devdata(master);
+
+ return clk_prepare_enable(spifc->clk);
+}
+#endif /* CONFIG_PM_RUNTIME */
+
+static const struct dev_pm_ops meson_spifc_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(meson_spifc_suspend, meson_spifc_resume)
+ SET_RUNTIME_PM_OPS(meson_spifc_runtime_suspend,
+ meson_spifc_runtime_resume,
+ NULL)
+};
+
+static const struct of_device_id meson_spifc_dt_match[] = {
+ { .compatible = "amlogic,meson6-spifc", },
+ { },
+};
+
+static struct platform_driver meson_spifc_driver = {
+ .probe = meson_spifc_probe,
+ .remove = meson_spifc_remove,
+ .driver = {
+ .name = "meson-spifc",
+ .of_match_table = of_match_ptr(meson_spifc_dt_match),
+ .pm = &meson_spifc_pm_ops,
+ },
+};
+
+module_platform_driver(meson_spifc_driver);
+
+MODULE_AUTHOR("Beniamino Galvani <[email protected]>");
+MODULE_DESCRIPTION("Amlogic Meson SPIFC driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1

2014-11-22 15:24:45

by Beniamino Galvani

[permalink] [raw]
Subject: [PATCH v3 4/4] ARM: dts: meson: add node for SPIFC

This adds a node for the SPI Flash Controller to the Amlogic Meson
DTS.

Signed-off-by: Beniamino Galvani <[email protected]>
Acked-by: Mark Brown <[email protected]>
---
arch/arm/boot/dts/meson.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/meson.dtsi
index b91e430..e26d37a 100644
--- a/arch/arm/boot/dts/meson.dtsi
+++ b/arch/arm/boot/dts/meson.dtsi
@@ -135,5 +135,14 @@
#address-cells = <1>;
#size-cells = <0>;
};
+
+ spifc: spi@c1108c80 {
+ compatible = "amlogic,meson6-spifc";
+ reg = <0xc1108c80 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clk81>;
+ status = "disabled";
+ };
};
}; /* end of / */
--
1.9.1

2014-11-22 15:25:19

by Beniamino Galvani

[permalink] [raw]
Subject: [PATCH v3 1/4] spi: core: Add spi_transfer_is_last() helper

This adds the function spi_transfer_is_last() which can be used by
drivers to know whether a given transfer is the last one in the
current message.

Signed-off-by: Beniamino Galvani <[email protected]>
---
include/linux/spi/spi.h | 6 ++++++
1 file changed, 6 insertions(+)

diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 46d188a..a6ef2a8 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -1049,4 +1049,10 @@ spi_unregister_device(struct spi_device *spi)
extern const struct spi_device_id *
spi_get_device_id(const struct spi_device *sdev);

+static inline bool
+spi_transfer_is_last(struct spi_master *master, struct spi_transfer *xfer)
+{
+ return list_is_last(&xfer->transfer_list, &master->cur_msg->transfers);
+}
+
#endif /* __LINUX_SPI_H */
--
1.9.1

2014-11-24 18:56:14

by Mark Brown

[permalink] [raw]
Subject: Re: [PATCH v3 1/4] spi: core: Add spi_transfer_is_last() helper

On Sat, Nov 22, 2014 at 04:21:39PM +0100, Beniamino Galvani wrote:
> This adds the function spi_transfer_is_last() which can be used by
> drivers to know whether a given transfer is the last one in the
> current message.

Applied, thanks.


Attachments:
(No filename) (239.00 B)
signature.asc (473.00 B)
Digital signature
Download all attachments

2014-11-24 18:56:57

by Mark Brown

[permalink] [raw]
Subject: Re: [PATCH v3 2/4] spi: meson: Add device tree bindings documentation for SPIFC

On Sat, Nov 22, 2014 at 04:21:40PM +0100, Beniamino Galvani wrote:
> This adds documentation of device tree bindings for the Amlogic Meson
> SPIFC (SPI Flash Controller).

Applied, thanks.


Attachments:
(No filename) (189.00 B)
signature.asc (473.00 B)
Digital signature
Download all attachments

2014-11-24 18:57:13

by Mark Brown

[permalink] [raw]
Subject: Re: [PATCH v3 3/4] spi: meson: Add support for Amlogic Meson SPIFC

On Sat, Nov 22, 2014 at 04:21:41PM +0100, Beniamino Galvani wrote:
> This is a driver for the Amlogic Meson SPIFC (SPI flash controller),
> which is one of the two SPI controllers available on the SoC. It
> doesn't support DMA and has a 64-byte unified transmit/receive buffer.

Applied, thanks.


Attachments:
(No filename) (296.00 B)
signature.asc (473.00 B)
Digital signature
Download all attachments