Hello,
this is a new driver for Western Digital WD7193, WD7197 and WD7296 PCI SCSI
controllers based on WD33C296A chip. These nice cards never worked good with
Linux.
It's based on old and ugly wd719x driver written back in 2.0 days, then hacked
to 2.2 and finally to 2.4 kernels. Most of the code is rewritten: from ~4100
lines to ~1200.
I've tested the driver on a WD7193 card with some hard drives and CD-ROMs:
QUANTUM LP240S GM240S01X 4.6
IBM 0663L12 e g
IBM DORS-32160 WA0A
SONY CD-ROM CDU-55S 1.0t
SONY CD-ROM CDU-415 1.1g
The card supports TCQ and linked commands (for cmd_per_lun > 1?) but I don't
know how it should be implemented in a driver.
Device/bus/host resets seem to work fine when tested by sg_reset.
But don't know how to test command abort.
The card requires firmware that can be cut out of the Windows NT driver that
can be downloaded from WD at:
http://support.wdc.com/product/download.asp?groupid=801&sid=27&lang=en
There is no license anywhere in the file or on the page - so I guess that the
firmware cannot be added to linux-firmware.
This script that downloads and extracts the firmware is in Documentation/
--
Ondrej Zary
Add documentation and script to obtain required firmware.
Signed-off-by: Ondrej Zary <[email protected]>
---
Documentation/scsi/wd719x.txt | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
create mode 100644 Documentation/scsi/wd719x.txt
diff --git a/Documentation/scsi/wd719x.txt b/Documentation/scsi/wd719x.txt
new file mode 100644
index 0000000..0816b02
--- /dev/null
+++ b/Documentation/scsi/wd719x.txt
@@ -0,0 +1,21 @@
+Driver for Western Digital WD7193, WD7197 and WD7296 SCSI cards
+---------------------------------------------------------------
+
+The card requires firmware that can be cut out of the Windows NT driver that
+can be downloaded from WD at:
+http://support.wdc.com/product/download.asp?groupid=801&sid=27&lang=en
+
+There is no license anywhere in the file or on the page - so the firmware
+probably cannot be added to linux-firmware.
+
+This script downloads and extracts the firmware, creating wd719x-risc.bin and
+d719x-wcs.bin files. Put them in /lib/firmware/.
+
+#!/bin/sh
+wget http://support.wdc.com/download/archive/pciscsi.exe
+lha xi pciscsi.exe pci-scsi.exe
+lha xi pci-scsi.exe nt/wd7296a.sys
+rm pci-scsi.exe
+dd if=wd7296a.sys of=wd719x-risc.bin bs=1 skip=5760 count=14336
+dd if=wd7296a.sys of=wd719x-wcs.bin bs=1 skip=20096 count=514
+rm wd7296a.sys
--
Ondrej Zary
Introduce wd719x, a driver for Western Digital WD7193, WD7197 and WD7296 PCI
SCSI controllers based on WD33C296A chip.
Tested with WD7193 card.
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Ondrej Zary <[email protected]>
---
drivers/scsi/Kconfig | 8 +
drivers/scsi/Makefile | 1 +
drivers/scsi/wd719x.c | 997 +++++++++++++++++++++++++++++++++++++++++++++++++
drivers/scsi/wd719x.h | 249 ++++++++++++
4 files changed, 1255 insertions(+)
create mode 100644 drivers/scsi/wd719x.c
create mode 100644 drivers/scsi/wd719x.h
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 3a820f6..fd81d14 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -1451,6 +1451,14 @@ config SCSI_NSP32
To compile this driver as a module, choose M here: the
module will be called nsp32.
+config SCSI_WD719X
+ tristate "Western Digital WD7193/7197/7296 support"
+ depends on PCI && SCSI
+ select EEPROM_93CX6
+ ---help---
+ This is a driver for Western Digital WD7193, WD7197 and WD7296 PCI
+ SCSI controllers (based on WD33C296A chip).
+
config SCSI_DEBUG
tristate "SCSI debugging host simulator"
depends on SCSI
diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile
index 59f1ce6..d8bfca5 100644
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -143,6 +143,7 @@ obj-$(CONFIG_SCSI_VIRTIO) += virtio_scsi.o
obj-$(CONFIG_VMWARE_PVSCSI) += vmw_pvscsi.o
obj-$(CONFIG_XEN_SCSI_FRONTEND) += xen-scsifront.o
obj-$(CONFIG_HYPERV_STORAGE) += hv_storvsc.o
+obj-$(CONFIG_SCSI_WD719X) += wd719x.o
obj-$(CONFIG_ARM) += arm/
diff --git a/drivers/scsi/wd719x.c b/drivers/scsi/wd719x.c
new file mode 100644
index 0000000..23bb5a3
--- /dev/null
+++ b/drivers/scsi/wd719x.c
@@ -0,0 +1,997 @@
+/*
+ * Driver for Western Digital WD7193, WD7197 and WD7296 SCSI cards
+ * Copyright 2013 Ondrej Zary
+ *
+ * Original driver by
+ * Aaron Dewell <[email protected]>
+ * Gaerti <[email protected]>
+ *
+ * HW documentation available in book:
+ *
+ * SPIDER Command Protocol
+ * by Chandru M. Sippy
+ * SCSI Storage Products (MCP)
+ * Western Digital Corporation
+ * 09-15-95
+ *
+ * http://web.archive.org/web/20070717175254/http://sun1.rrzn.uni-hannover.de/gaertner.juergen/wd719x/Linux/Docu/Spider/
+ */
+
+/*
+ * Driver workflow:
+ * 1. SCSI command is transformed to SCB (Spider Control Block) by the
+ * queuecommand function.
+ * 2. The address of the SCB is stored in a list to be able to access it, if
+ * something goes wrong.
+ * 3. The address of the SCB is written to the Controller, which loads the SCB
+ * via BM-DMA and processes it.
+ * 4. After it has finished, it generates an interrupt, and sets registers.
+ *
+ * flaws:
+ * - abort/reset functions
+ *
+ * ToDo:
+ * - tagged queueing
+ */
+
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/firmware.h>
+#include <linux/eeprom_93cx6.h>
+#include <scsi/scsi_cmnd.h>
+#include <scsi/scsi_device.h>
+#include <scsi/scsi_host.h>
+#include "wd719x.h"
+
+/* low-level register access */
+static inline u8 wd719x_readb(struct wd719x *wd, u8 reg)
+{
+ return ioread8(wd->base + reg);
+}
+
+static inline u32 wd719x_readl(struct wd719x *wd, u8 reg)
+{
+ return ioread32(wd->base + reg);
+}
+
+static inline void wd719x_writeb(struct wd719x *wd, u8 reg, u8 val)
+{
+ iowrite8(val, wd->base + reg);
+}
+
+static inline void wd719x_writew(struct wd719x *wd, u8 reg, u16 val)
+{
+ iowrite16(val, wd->base + reg);
+}
+
+static inline void wd719x_writel(struct wd719x *wd, u8 reg, u32 val)
+{
+ iowrite32(val, wd->base + reg);
+}
+
+/* wait until the command register is ready */
+static inline int wd719x_wait_ready(struct wd719x *wd)
+{
+ int i = 0;
+
+ do {
+ if (wd719x_readb(wd, WD719X_AMR_COMMAND) == WD719X_CMD_READY)
+ return 0;
+ udelay(1);
+ } while (i++ < WD719X_WAIT_FOR_CMD_READY);
+
+ dev_err(&wd->pdev->dev, "command register is not ready: 0x%02x\n",
+ wd719x_readb(wd, WD719X_AMR_COMMAND));
+
+ return -ETIMEDOUT;
+}
+
+/* poll interrupt status register until command finishes */
+static inline int wd719x_wait_done(struct wd719x *wd, int timeout)
+{
+ u8 status;
+
+ while (timeout > 0) {
+ status = wd719x_readb(wd, WD719X_AMR_INT_STATUS);
+ if (status)
+ break;
+ timeout--;
+ udelay(1);
+ }
+
+ if (timeout <= 0) {
+ dev_err(&wd->pdev->dev, "direct command timed out\n");
+ return -ETIMEDOUT;
+ }
+
+ if (status != WD719X_INT_NOERRORS) {
+ dev_err(&wd->pdev->dev, "direct command failed, status 0x%02x, SUE 0x%02x\n",
+ status, wd719x_readb(wd, WD719X_AMR_SCB_ERROR));
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int wd719x_direct_cmd(struct wd719x *wd, u8 opcode, u8 dev, u8 lun,
+ u8 tag, dma_addr_t data, int timeout)
+{
+ int ret = 0;
+
+ /* clear interrupt status register (allow command register to clear) */
+ wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
+
+ /* Wait for the Command register to become free */
+ if (wd719x_wait_ready(wd))
+ return -ETIMEDOUT;
+
+ /* make sure we get NO interrupts */
+ dev |= WD719X_DISABLE_INT;
+ wd719x_writeb(wd, WD719X_AMR_CMD_PARAM, dev);
+ wd719x_writeb(wd, WD719X_AMR_CMD_PARAM_2, lun);
+ wd719x_writeb(wd, WD719X_AMR_CMD_PARAM_3, tag);
+ if (data)
+ wd719x_writel(wd, WD719X_AMR_SCB_IN, data);
+
+ /* clear interrupt status register again */
+ wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
+
+ /* Now, write the command */
+ wd719x_writeb(wd, WD719X_AMR_COMMAND, opcode);
+
+ if (timeout) /* wait for the command to complete */
+ ret = wd719x_wait_done(wd, timeout);
+
+ /* clear interrupt status register (clean up) */
+ if (opcode != WD719X_CMD_READ_FIRMVER)
+ wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
+
+ return ret;
+}
+
+static void wd719x_destroy(struct wd719x *wd)
+{
+ struct wd719x_scb *scb;
+
+ /* stop the RISC */
+ if (wd719x_direct_cmd(wd, WD719X_CMD_SLEEP, 0, 0, 0, 0,
+ WD719X_WAIT_FOR_RISC))
+ dev_warn(&wd->pdev->dev, "RISC sleep command failed\n");
+ /* disable RISC */
+ wd719x_writeb(wd, WD719X_PCI_MODE_SELECT, 0);
+
+ /* free all SCBs */
+ list_for_each_entry(scb, &wd->active_scbs, list)
+ pci_free_consistent(wd->pdev, sizeof(struct wd719x_scb), scb,
+ scb->phys);
+ list_for_each_entry(scb, &wd->free_scbs, list)
+ pci_free_consistent(wd->pdev, sizeof(struct wd719x_scb), scb,
+ scb->phys);
+ /* free internal buffers */
+ pci_free_consistent(wd->pdev, wd->fw_size, wd->fw_virt, wd->fw_phys);
+ wd->fw_virt = NULL;
+ pci_free_consistent(wd->pdev, WD719X_HASH_TABLE_SIZE, wd->hash_virt,
+ wd->hash_phys);
+ wd->hash_virt = NULL;
+ pci_free_consistent(wd->pdev, sizeof(struct wd719x_host_param),
+ wd->params, wd->params_phys);
+ wd->params = NULL;
+ free_irq(wd->pdev->irq, wd);
+}
+
+/* finish a SCSI command, mark SCB (if any) as free, unmap buffers */
+static void wd719x_finish_cmd(struct scsi_cmnd *cmd, int result)
+{
+ struct wd719x *wd = shost_priv(cmd->device->host);
+ struct wd719x_scb *scb = (struct wd719x_scb *) cmd->host_scribble;
+
+ if (scb) {
+ list_move(&scb->list, &wd->free_scbs);
+ dma_unmap_single(&wd->pdev->dev, cmd->SCp.dma_handle,
+ SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE);
+ scsi_dma_unmap(cmd);
+ }
+ cmd->result = result << 16;
+ cmd->scsi_done(cmd);
+}
+
+/* Build a SCB and send it to the card */
+static int wd719x_queuecommand(struct Scsi_Host *sh, struct scsi_cmnd *cmd)
+{
+ int i, count_sg;
+ unsigned long flags;
+ struct wd719x_scb *scb;
+ struct wd719x *wd = shost_priv(sh);
+ dma_addr_t phys;
+
+ cmd->host_scribble = NULL;
+
+ /* get a free SCB - either from existing ones or allocate a new one */
+ spin_lock_irqsave(wd->sh->host_lock, flags);
+ scb = list_first_entry_or_null(&wd->free_scbs, struct wd719x_scb, list);
+ if (scb) {
+ list_del(&scb->list);
+ phys = scb->phys;
+ } else {
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+ scb = pci_alloc_consistent(wd->pdev, sizeof(struct wd719x_scb),
+ &phys);
+ spin_lock_irqsave(wd->sh->host_lock, flags);
+ if (!scb) {
+ dev_err(&wd->pdev->dev, "unable to allocate SCB\n");
+ wd719x_finish_cmd(cmd, DID_ERROR);
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+ return 0;
+ }
+ }
+ memset(scb, 0, sizeof(struct wd719x_scb));
+ list_add(&scb->list, &wd->active_scbs);
+
+ scb->phys = phys;
+ scb->cmd = cmd;
+ cmd->host_scribble = (char *) scb;
+
+ scb->CDB_tag = 0; /* Tagged queueing not supported yet */
+ scb->devid = cmd->device->id;
+ scb->lun = cmd->device->lun;
+
+ /* copy the command */
+ memcpy(scb->CDB, cmd->cmnd, cmd->cmd_len);
+
+ /* map sense buffer */
+ scb->sense_buf_length = SCSI_SENSE_BUFFERSIZE;
+ cmd->SCp.dma_handle = dma_map_single(&wd->pdev->dev, cmd->sense_buffer,
+ SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE);
+ dma_cache_sync(&wd->pdev->dev, cmd->sense_buffer,
+ SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE);
+ scb->sense_buf = cpu_to_le32(cmd->SCp.dma_handle);
+
+ /* request autosense */
+ scb->SCB_options |= WD719X_SCB_FLAGS_AUTO_REQUEST_SENSE;
+
+ /* check direction */
+ if (cmd->sc_data_direction == DMA_TO_DEVICE)
+ scb->SCB_options |= WD719X_SCB_FLAGS_CHECK_DIRECTION
+ | WD719X_SCB_FLAGS_PCI_TO_SCSI;
+ else if (cmd->sc_data_direction == DMA_FROM_DEVICE)
+ scb->SCB_options |= WD719X_SCB_FLAGS_CHECK_DIRECTION;
+
+ /* Scather/gather */
+ count_sg = scsi_dma_map(cmd);
+ if (count_sg < 0) {
+ wd719x_finish_cmd(cmd, DID_ERROR);
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+ return 0;
+ }
+ BUG_ON(count_sg > WD719X_SG);
+
+ if (count_sg) {
+ struct scatterlist *sg;
+
+ scb->data_length = cpu_to_le32(count_sg *
+ sizeof(struct wd719x_sglist));
+ scb->data_p = cpu_to_le32(scb->phys +
+ offsetof(struct wd719x_scb, sg_list));
+
+ scsi_for_each_sg(cmd, sg, count_sg, i) {
+ scb->sg_list[i].ptr = cpu_to_le32(sg_dma_address(sg));
+ scb->sg_list[i].length = cpu_to_le32(sg_dma_len(sg));
+ }
+ scb->SCB_options |= WD719X_SCB_FLAGS_DO_SCATTER_GATHER;
+ } else { /* zero length */
+ scb->data_length = 0;
+ scb->data_p = 0;
+ }
+
+ /* check if the Command register is free */
+ if (wd719x_readb(wd, WD719X_AMR_COMMAND) != WD719X_CMD_READY) {
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+ return SCSI_MLQUEUE_HOST_BUSY;
+ }
+
+ /* write pointer to the AMR */
+ wd719x_writel(wd, WD719X_AMR_SCB_IN, scb->phys);
+ /* send SCB opcode */
+ wd719x_writeb(wd, WD719X_AMR_COMMAND, WD719X_CMD_PROCESS_SCB);
+
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+
+ return 0;
+}
+
+static int wd719x_chip_init(struct wd719x *wd)
+{
+ int i, ret;
+ u32 risc_init[3];
+ const struct firmware *fw_wcs, *fw_risc;
+ const char fwname_wcs[] = "wd719x-wcs.bin";
+ const char fwname_risc[] = "wd719x-risc.bin";
+
+ memset(wd->hash_virt, 0, WD719X_HASH_TABLE_SIZE);
+
+ /* WCS (sequencer) firmware */
+ ret = request_firmware(&fw_wcs, fwname_wcs, &wd->pdev->dev);
+ if (ret) {
+ dev_err(&wd->pdev->dev, "Unable to load firmware %s: %d\n",
+ fwname_wcs, ret);
+ return ret;
+ }
+ /* RISC firmware */
+ ret = request_firmware(&fw_risc, fwname_risc, &wd->pdev->dev);
+ if (ret) {
+ dev_err(&wd->pdev->dev, "Unable to load firmware %s: %d\n",
+ fwname_risc, ret);
+ release_firmware(fw_wcs);
+ return ret;
+ }
+ wd->fw_size = ALIGN(fw_wcs->size, 4) + fw_risc->size;
+
+ if (!wd->fw_virt)
+ wd->fw_virt = pci_alloc_consistent(wd->pdev, wd->fw_size,
+ &wd->fw_phys);
+ if (!wd->fw_virt) {
+ ret = -ENOMEM;
+ goto wd719x_init_end;
+ }
+
+ /* make a fresh copy of WCS and RISC code */
+ memcpy(wd->fw_virt, fw_wcs->data, fw_wcs->size);
+ memcpy(wd->fw_virt + ALIGN(fw_wcs->size, 4), fw_risc->data,
+ fw_risc->size);
+
+ /* Reset the Spider Chip and adapter itself */
+ wd719x_writeb(wd, WD719X_PCI_PORT_RESET, WD719X_PCI_RESET);
+ udelay(WD719X_WAIT_FOR_RISC);
+ /* Clear PIO mode bits set by BIOS */
+ wd719x_writeb(wd, WD719X_AMR_CMD_PARAM, 0);
+ /* ensure RISC is not running */
+ wd719x_writeb(wd, WD719X_PCI_MODE_SELECT, 0);
+ /* ensure command port is ready */
+ wd719x_writeb(wd, WD719X_AMR_COMMAND, 0);
+ if (wd719x_wait_ready(wd)) {
+ ret = -ETIMEDOUT;
+ goto wd719x_init_end;
+ }
+
+ /* Transfer the first 2K words of RISC code to kick start the uP */
+ risc_init[0] = wd->fw_phys; /* WCS FW */
+ risc_init[1] = wd->fw_phys + ALIGN(fw_wcs->size, 4); /* RISC FW */
+ risc_init[2] = wd->hash_phys; /* hash table */
+
+ /* clear DMA status */
+ wd719x_writeb(wd, WD719X_PCI_CHANNEL2_3STATUS, 0);
+
+ /* address to read firmware from */
+ wd719x_writel(wd, WD719X_PCI_EXTERNAL_ADDR, risc_init[1]);
+ /* base address to write firmware to (on card) */
+ wd719x_writew(wd, WD719X_PCI_INTERNAL_ADDR, WD719X_PRAM_BASE_ADDR);
+ /* size: first 2K words */
+ wd719x_writew(wd, WD719X_PCI_DMA_TRANSFER_SIZE, 2048 * 2);
+ /* start DMA */
+ wd719x_writeb(wd, WD719X_PCI_CHANNEL2_3CMD, WD719X_START_CHANNEL2_3DMA);
+
+ /* wait for DMA to complete */
+ i = WD719X_WAIT_FOR_RISC;
+ while (i-- > 0) {
+ u8 status = wd719x_readb(wd, WD719X_PCI_CHANNEL2_3STATUS);
+ if (status == WD719X_START_CHANNEL2_3DONE)
+ break;
+ if (status == WD719X_START_CHANNEL2_3ABORT) {
+ dev_warn(&wd->pdev->dev, "RISC bootstrap failed: DMA aborted\n");
+ ret = -EIO;
+ goto wd719x_init_end;
+ }
+ udelay(1);
+ }
+ if (i < 1) {
+ dev_warn(&wd->pdev->dev, "RISC bootstrap failed: DMA timeout\n");
+ ret = -ETIMEDOUT;
+ goto wd719x_init_end;
+ }
+
+ /* firmware is loaded, now initialize and wake up the RISC */
+ /* write RISC initialization long words to Spider */
+ wd719x_writel(wd, WD719X_AMR_SCB_IN, risc_init[0]);
+ wd719x_writel(wd, WD719X_AMR_SCB_IN + 4, risc_init[1]);
+ wd719x_writel(wd, WD719X_AMR_SCB_IN + 8, risc_init[2]);
+
+ /* disable interrupts during initialization of RISC */
+ wd719x_writeb(wd, WD719X_AMR_CMD_PARAM, WD719X_DISABLE_INT);
+
+ /* issue INITIALIZE RISC comand */
+ wd719x_writeb(wd, WD719X_AMR_COMMAND, WD719X_CMD_INIT_RISC);
+ /* enable advanced mode (wake up RISC) */
+ wd719x_writeb(wd, WD719X_PCI_MODE_SELECT, WD719X_ENABLE_ADVANCE_MODE);
+ udelay(WD719X_WAIT_FOR_RISC);
+
+ ret = wd719x_wait_done(wd, WD719X_WAIT_FOR_RISC);
+ /* clear interrupt status register */
+ wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
+ if (ret) {
+ dev_warn(&wd->pdev->dev, "Unable to initialize RISC\n");
+ goto wd719x_init_end;
+ }
+ /* RISC is up and running */
+
+ /* Read FW version from RISC */
+ ret = wd719x_direct_cmd(wd, WD719X_CMD_READ_FIRMVER, 0, 0, 0, 0,
+ WD719X_WAIT_FOR_RISC);
+ if (ret) {
+ dev_warn(&wd->pdev->dev, "Unable to read firmware version\n");
+ goto wd719x_init_end;
+ }
+ dev_info(&wd->pdev->dev, "RISC initialized with firmware version %.2x.%.2x\n",
+ wd719x_readb(wd, WD719X_AMR_SCB_OUT + 1),
+ wd719x_readb(wd, WD719X_AMR_SCB_OUT));
+
+ /* RESET SCSI bus */
+ ret = wd719x_direct_cmd(wd, WD719X_CMD_BUSRESET, 0, 0, 0, 0,
+ WD719X_WAIT_FOR_SCSI_RESET);
+ if (ret) {
+ dev_warn(&wd->pdev->dev, "SCSI bus reset failed\n");
+ goto wd719x_init_end;
+ }
+
+ /* use HostParameter structure to set Spider's Host Parameter Block */
+ ret = wd719x_direct_cmd(wd, WD719X_CMD_SET_PARAM, 0,
+ sizeof(struct wd719x_host_param), 0,
+ wd->params_phys, WD719X_WAIT_FOR_RISC);
+ if (ret) {
+ dev_warn(&wd->pdev->dev, "Failed to set HOST PARAMETERS\n");
+ goto wd719x_init_end;
+ }
+
+ /* initiate SCAM (does nothing if disabled in BIOS) */
+ /* bug?: we should pass a mask of static IDs which we don't have */
+ ret = wd719x_direct_cmd(wd, WD719X_CMD_INIT_SCAM, 0, 0, 0, 0,
+ WD719X_WAIT_FOR_SCSI_RESET);
+ if (ret) {
+ dev_warn(&wd->pdev->dev, "SCAM initialization failed\n");
+ goto wd719x_init_end;
+ }
+
+ /* clear AMR_BIOS_SHARE_INT register */
+ wd719x_writeb(wd, WD719X_AMR_BIOS_SHARE_INT, 0);
+
+wd719x_init_end:
+ release_firmware(fw_wcs);
+ release_firmware(fw_risc);
+
+ return ret;
+}
+
+static int wd719x_abort(struct scsi_cmnd *cmd)
+{
+ int action, result;
+ unsigned long flags;
+ struct wd719x_scb *scb = (struct wd719x_scb *)cmd->host_scribble;
+ struct wd719x *wd = shost_priv(cmd->device->host);
+
+ dev_info(&wd->pdev->dev, "abort command, tag: %x\n", cmd->tag);
+
+ action = /*cmd->tag ? WD719X_CMD_ABORT_TAG : */WD719X_CMD_ABORT;
+
+ spin_lock_irqsave(wd->sh->host_lock, flags);
+ result = wd719x_direct_cmd(wd, action, cmd->device->id,
+ cmd->device->lun, cmd->tag, scb->phys, 0);
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+ if (result)
+ return FAILED;
+
+ return SUCCESS;
+}
+
+static int wd719x_reset(struct scsi_cmnd *cmd, u8 opcode, u8 device)
+{
+ int result;
+ unsigned long flags;
+ struct wd719x *wd = shost_priv(cmd->device->host);
+
+ dev_info(&wd->pdev->dev, "%s reset requested\n",
+ (opcode == WD719X_CMD_BUSRESET) ? "bus" : "device");
+
+ spin_lock_irqsave(wd->sh->host_lock, flags);
+ result = wd719x_direct_cmd(wd, opcode, device, 0, 0, 0,
+ WD719X_WAIT_FOR_SCSI_RESET);
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+ if (result)
+ return FAILED;
+
+ return SUCCESS;
+}
+
+static int wd719x_dev_reset(struct scsi_cmnd *cmd)
+{
+ return wd719x_reset(cmd, WD719X_CMD_RESET, cmd->device->id);
+}
+
+static int wd719x_bus_reset(struct scsi_cmnd *cmd)
+{
+ return wd719x_reset(cmd, WD719X_CMD_BUSRESET, 0);
+}
+
+static int wd719x_host_reset(struct scsi_cmnd *cmd)
+{
+ struct wd719x *wd = shost_priv(cmd->device->host);
+ struct wd719x_scb *scb, *tmp;
+ unsigned long flags;
+ int result;
+
+ dev_info(&wd->pdev->dev, "host reset requested\n");
+ spin_lock_irqsave(wd->sh->host_lock, flags);
+ /* Try to reinit the RISC */
+ if (wd719x_chip_init(wd) == 0)
+ result = SUCCESS;
+ else
+ result = FAILED;
+
+ /* flush all SCBs */
+ list_for_each_entry_safe(scb, tmp, &wd->active_scbs, list) {
+ struct scsi_cmnd *tmp_cmd = scb->cmd;
+ wd719x_finish_cmd(tmp_cmd, result);
+ }
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+
+ return result;
+}
+
+static int wd719x_biosparam(struct scsi_device *sdev, struct block_device *bdev,
+ sector_t capacity, int geom[])
+{
+ if (capacity >= 0x200000) {
+ geom[0] = 255; /* heads */
+ geom[1] = 63; /* sectors */
+ } else {
+ geom[0] = 64; /* heads */
+ geom[1] = 32; /* sectors */
+ }
+ geom[2] = sector_div(capacity, geom[0] * geom[1]); /* cylinders */
+
+ return 0;
+}
+
+/* process a SCB-completion interrupt */
+static inline void wd719x_interrupt_SCB(struct wd719x *wd,
+ union wd719x_regs regs,
+ struct wd719x_scb *scb)
+{
+ struct scsi_cmnd *cmd;
+ int result;
+
+ /* now have to find result from card */
+ switch (regs.bytes.SUE) {
+ case WD719X_SUE_NOERRORS:
+ result = DID_OK;
+ break;
+ case WD719X_SUE_REJECTED:
+ dev_err(&wd->pdev->dev, "command rejected\n");
+ result = DID_ERROR;
+ break;
+ case WD719X_SUE_SCBQFULL:
+ dev_err(&wd->pdev->dev, "SCB queue is full\n");
+ result = DID_ERROR;
+ break;
+ case WD719X_SUE_TERM:
+ dev_dbg(&wd->pdev->dev, "SCB terminated by direct command\n");
+ result = DID_ABORT; /* or DID_RESET? */
+ break;
+ case WD719X_SUE_CHAN1ABORT:
+ case WD719X_SUE_CHAN23ABORT:
+ result = DID_ABORT;
+ dev_err(&wd->pdev->dev, "DMA abort\n");
+ break;
+ case WD719X_SUE_CHAN1PAR:
+ case WD719X_SUE_CHAN23PAR:
+ result = DID_PARITY;
+ dev_err(&wd->pdev->dev, "DMA parity error\n");
+ break;
+ case WD719X_SUE_TIMEOUT:
+ result = DID_TIME_OUT;
+ dev_dbg(&wd->pdev->dev, "selection timeout\n");
+ break;
+ case WD719X_SUE_RESET:
+ dev_dbg(&wd->pdev->dev, "bus reset occured\n");
+ result = DID_RESET;
+ break;
+ case WD719X_SUE_BUSERROR:
+ dev_dbg(&wd->pdev->dev, "SCSI bus error\n");
+ result = DID_ERROR;
+ break;
+ case WD719X_SUE_WRONGWAY:
+ dev_err(&wd->pdev->dev, "wrong data transfer direction\n");
+ result = DID_ERROR;
+ break;
+ case WD719X_SUE_BADPHASE:
+ dev_err(&wd->pdev->dev, "invalid SCSI phase\n");
+ result = DID_ERROR;
+ break;
+ case WD719X_SUE_TOOLONG:
+ dev_err(&wd->pdev->dev, "record too long\n");
+ result = DID_ERROR;
+ break;
+ case WD719X_SUE_BUSFREE:
+ dev_err(&wd->pdev->dev, "unexpected bus free\n");
+ result = DID_NO_CONNECT; /* or DID_ERROR ???*/
+ break;
+ case WD719X_SUE_ARSDONE:
+ dev_dbg(&wd->pdev->dev, "auto request sense\n");
+ if (regs.bytes.SCSI == 0)
+ result = DID_OK;
+ else
+ result = DID_PARITY;
+ break;
+ case WD719X_SUE_IGNORED:
+ dev_err(&wd->pdev->dev, "target id %d ignored command\n",
+ scb->cmd->device->id);
+ result = DID_NO_CONNECT;
+ break;
+ case WD719X_SUE_WRONGTAGS:
+ dev_err(&wd->pdev->dev, "reversed tags\n");
+ result = DID_ERROR;
+ break;
+ case WD719X_SUE_BADTAGS:
+ dev_err(&wd->pdev->dev, "tag type not supported by target\n");
+ result = DID_ERROR;
+ break;
+ case WD719X_SUE_NOSCAMID:
+ dev_err(&wd->pdev->dev, "no SCAM soft ID available\n");
+ result = DID_ERROR;
+ break;
+ default:
+ dev_warn(&wd->pdev->dev, "unknown SUE error code: 0x%x\n",
+ regs.bytes.SUE);
+ result = DID_ERROR;
+ break;
+ }
+ cmd = scb->cmd;
+
+ wd719x_finish_cmd(cmd, result);
+}
+
+static irqreturn_t wd719x_interrupt(int irq, void *dev_id)
+{
+ struct wd719x *wd = dev_id;
+ union wd719x_regs regs;
+ unsigned long flags;
+ u32 SCB_out;
+
+ spin_lock_irqsave(wd->sh->host_lock, flags);
+ /* read SCB pointer back from card */
+ SCB_out = wd719x_readl(wd, WD719X_AMR_SCB_OUT);
+ /* read all status info at once */
+ regs.all = cpu_to_le32(wd719x_readl(wd, WD719X_AMR_OP_CODE));
+
+ switch (regs.bytes.INT) {
+ case WD719X_INT_NONE:
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+ return IRQ_NONE;
+ case WD719X_INT_LINKNOSTATUS:
+ dev_err(&wd->pdev->dev, "linked command completed with no status\n");
+ break;
+ case WD719X_INT_BADINT:
+ dev_err(&wd->pdev->dev, "unsolicited interrupt\n");
+ break;
+ case WD719X_INT_NOERRORS:
+ case WD719X_INT_LINKNOERRORS:
+ case WD719X_INT_ERRORSLOGGED:
+ case WD719X_INT_SPIDERFAILED:
+ /* was the cmd completed a direct or SCB command? */
+ if (regs.bytes.OPC == WD719X_CMD_PROCESS_SCB) {
+ struct wd719x_scb *scb;
+ list_for_each_entry(scb, &wd->active_scbs, list)
+ if (SCB_out == scb->phys)
+ break;
+ if (SCB_out == scb->phys)
+ wd719x_interrupt_SCB(wd, regs, scb);
+ else
+ dev_err(&wd->pdev->dev, "card returned invalid SCB pointer\n");
+ } else
+ dev_warn(&wd->pdev->dev, "direct command 0x%x completed\n",
+ regs.bytes.OPC);
+ break;
+ case WD719X_INT_PIOREADY:
+ dev_err(&wd->pdev->dev, "card indicates PIO data ready but we never use PIO\n");
+ /* interrupt will not be cleared until all data is read */
+ break;
+ default:
+ dev_err(&wd->pdev->dev, "unknown interrupt reason: %d\n",
+ regs.bytes.INT);
+
+ }
+ /* clear interrupt so another can happen */
+ wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE);
+ spin_unlock_irqrestore(wd->sh->host_lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+static void wd719x_eeprom_reg_read(struct eeprom_93cx6 *eeprom)
+{
+ struct wd719x *wd = eeprom->data;
+ u8 reg = wd719x_readb(wd, WD719X_PCI_GPIO_DATA);
+
+ eeprom->reg_data_out = reg & WD719X_EE_DO;
+}
+
+static void wd719x_eeprom_reg_write(struct eeprom_93cx6 *eeprom)
+{
+ struct wd719x *wd = eeprom->data;
+ u8 reg = 0;
+
+ if (eeprom->reg_data_in)
+ reg |= WD719X_EE_DI;
+ if (eeprom->reg_data_clock)
+ reg |= WD719X_EE_CLK;
+ if (eeprom->reg_chip_select)
+ reg |= WD719X_EE_CS;
+
+ wd719x_writeb(wd, WD719X_PCI_GPIO_DATA, reg);
+}
+
+/* read config from EEPROM so it can be downloaded by the RISC on (re-)init */
+static void wd719x_read_eeprom(struct wd719x *wd)
+{
+ struct eeprom_93cx6 eeprom;
+ u8 gpio;
+ struct wd719x_eeprom_header header;
+
+ eeprom.data = wd;
+ eeprom.register_read = wd719x_eeprom_reg_read;
+ eeprom.register_write = wd719x_eeprom_reg_write;
+ eeprom.width = PCI_EEPROM_WIDTH_93C46;
+
+ /* set all outputs to low */
+ wd719x_writeb(wd, WD719X_PCI_GPIO_DATA, 0);
+ /* configure GPIO pins */
+ gpio = wd719x_readb(wd, WD719X_PCI_GPIO_CONTROL);
+ /* GPIO outputs */
+ gpio &= (~(WD719X_EE_CLK | WD719X_EE_DI | WD719X_EE_CS));
+ /* GPIO input */
+ gpio |= WD719X_EE_DO;
+ wd719x_writeb(wd, WD719X_PCI_GPIO_CONTROL, gpio);
+
+ /* read EEPROM header */
+ eeprom_93cx6_multireadb(&eeprom, 0, (u8 *)&header, sizeof(header));
+
+ if (header.sig1 == 'W' && header.sig2 == 'D')
+ eeprom_93cx6_multireadb(&eeprom, header.cfg_offset,
+ (u8 *)wd->params,
+ sizeof(struct wd719x_host_param));
+ else { /* default EEPROM values */
+ dev_warn(&wd->pdev->dev, "EEPROM signature is invalid (0x%02x 0x%02x), using default values\n",
+ header.sig1, header.sig2);
+ wd->params->ch_1_th = 0x10; /* 16 DWs = 64 B */
+ wd->params->scsi_conf = 0x4c; /* 48ma, spue, parity check */
+ wd->params->own_scsi_id = 0x07; /* ID 7, SCAM disabled */
+ wd->params->sel_timeout = 0x4d; /* 250 ms */
+ wd->params->sleep_timer = 0x01;
+ wd->params->cdb_size = cpu_to_le16(0x5555); /* all 6 B */
+ wd->params->scsi_pad = 0x1b;
+ if (wd->type == WD719X_TYPE_7193) /* narrow card - disable */
+ wd->params->wide = cpu_to_le32(0x00000000);
+ else /* initiate & respond to WIDE messages */
+ wd->params->wide = cpu_to_le32(0xffffffff);
+ wd->params->sync = cpu_to_le32(0xffffffff);
+ wd->params->soft_mask = 0x00; /* all disabled */
+ wd->params->unsol_mask = 0x00; /* all disabled */
+ }
+ /* disable TAGGED messages */
+ wd->params->tag_en = cpu_to_le16(0x0000);
+}
+
+/* Read card type from GPIO bits 1 and 3 */
+static enum wd719x_card_type wd719x_detect_type(struct wd719x *wd)
+{
+ u8 card = wd719x_readb(wd, WD719X_PCI_GPIO_CONTROL);
+
+ card |= WD719X_GPIO_ID_BITS;
+ wd719x_writeb(wd, WD719X_PCI_GPIO_CONTROL, card);
+ card = wd719x_readb(wd, WD719X_PCI_GPIO_DATA) & WD719X_GPIO_ID_BITS;
+ switch (card) {
+ case 0x08:
+ return WD719X_TYPE_7193;
+ case 0x02:
+ return WD719X_TYPE_7197;
+ case 0x00:
+ return WD719X_TYPE_7296;
+ default:
+ dev_warn(&wd->pdev->dev, "unknown card type 0x%x\n", card);
+ return WD719X_TYPE_UNKNOWN;
+ }
+}
+
+static int wd719x_board_found(struct Scsi_Host *sh)
+{
+ struct wd719x *wd = shost_priv(sh);
+ char *card_types[] = { "Unknown card", "WD7193", "WD7197", "WD7296" };
+ int ret;
+
+ INIT_LIST_HEAD(&wd->active_scbs);
+ INIT_LIST_HEAD(&wd->free_scbs);
+
+ sh->base = pci_resource_start(wd->pdev, 0);
+
+ wd->type = wd719x_detect_type(wd);
+
+ wd->sh = sh;
+ sh->irq = wd->pdev->irq;
+ wd->fw_virt = NULL;
+
+ /* memory area for host (EEPROM) parameters */
+ wd->params = pci_alloc_consistent(wd->pdev,
+ sizeof(struct wd719x_host_param),
+ &wd->params_phys);
+ if (!wd->params) {
+ dev_warn(&wd->pdev->dev, "unable to allocate parameter buffer\n");
+ return -ENOMEM;
+ }
+
+ /* memory area for the RISC for hash table of outstanding requests */
+ wd->hash_virt = pci_alloc_consistent(wd->pdev, WD719X_HASH_TABLE_SIZE,
+ &wd->hash_phys);
+ if (!wd->hash_virt) {
+ dev_warn(&wd->pdev->dev, "unable to allocate hash buffer\n");
+ ret = -ENOMEM;
+ goto fail_free_params;
+ }
+
+ ret = request_irq(wd->pdev->irq, wd719x_interrupt, IRQF_SHARED,
+ "wd719x", wd);
+ if (ret) {
+ dev_warn(&wd->pdev->dev, "unable to assign IRQ %d\n",
+ wd->pdev->irq);
+ goto fail_free_hash;
+ }
+
+ /* read parameters from EEPROM */
+ wd719x_read_eeprom(wd);
+
+ ret = wd719x_chip_init(wd);
+ if (ret)
+ goto fail_free_irq;
+
+ sh->this_id = wd->params->own_scsi_id & WD719X_EE_SCSI_ID_MASK;
+
+ dev_info(&wd->pdev->dev, "%s at I/O 0x%lx, IRQ %u, SCSI ID %d\n",
+ card_types[wd->type], sh->base, sh->irq, sh->this_id);
+
+ return 0;
+
+fail_free_irq:
+ free_irq(wd->pdev->irq, wd);
+fail_free_hash:
+ pci_free_consistent(wd->pdev, WD719X_HASH_TABLE_SIZE, wd->hash_virt,
+ wd->hash_phys);
+fail_free_params:
+ pci_free_consistent(wd->pdev, sizeof(struct wd719x_host_param),
+ wd->params, wd->params_phys);
+
+ return ret;
+}
+
+static struct scsi_host_template wd719x_template = {
+ .name = "Western Digital 719x",
+ .queuecommand = wd719x_queuecommand,
+ .eh_abort_handler = wd719x_abort,
+ .eh_device_reset_handler = wd719x_dev_reset,
+ .eh_bus_reset_handler = wd719x_bus_reset,
+ .eh_host_reset_handler = wd719x_host_reset,
+ .bios_param = wd719x_biosparam,
+ .proc_name = "wd719x",
+ .can_queue = 255,
+ .this_id = 7,
+ .sg_tablesize = WD719X_SG,
+ .cmd_per_lun = WD719X_CMD_PER_LUN,
+ .use_clustering = ENABLE_CLUSTERING,
+};
+
+static int wd719x_pci_probe(struct pci_dev *pdev, const struct pci_device_id *d)
+{
+ int err;
+ struct Scsi_Host *sh;
+ struct wd719x *wd;
+
+ err = pci_enable_device(pdev);
+ if (err)
+ goto fail;
+
+ if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
+ dev_warn(&pdev->dev, "Unable to set 32-bit DMA mask\n");
+ goto disable_device;
+ }
+
+ err = pci_request_regions(pdev, "wd719x");
+ if (err)
+ goto disable_device;
+ pci_set_master(pdev);
+
+ err = -ENODEV;
+ if (pci_resource_len(pdev, 0) == 0)
+ goto release_region;
+
+ err = -ENOMEM;
+ sh = scsi_host_alloc(&wd719x_template, sizeof(struct wd719x));
+ if (!sh)
+ goto release_region;
+
+ wd = shost_priv(sh);
+ wd->base = pci_iomap(pdev, 0, 0);
+ if (!wd->base)
+ goto free_host;
+ wd->pdev = pdev;
+
+ err = wd719x_board_found(sh);
+ if (err)
+ goto unmap;
+
+ err = scsi_add_host(sh, &wd->pdev->dev);
+ if (err)
+ goto destroy;
+
+ scsi_scan_host(sh);
+
+ pci_set_drvdata(pdev, sh);
+ return 0;
+
+destroy:
+ wd719x_destroy(wd);
+unmap:
+ pci_iounmap(pdev, wd->base);
+free_host:
+ scsi_host_put(sh);
+release_region:
+ pci_release_regions(pdev);
+disable_device:
+ pci_disable_device(pdev);
+fail:
+ return err;
+}
+
+
+static void wd719x_pci_remove(struct pci_dev *pdev)
+{
+ struct Scsi_Host *sh = pci_get_drvdata(pdev);
+ struct wd719x *wd = shost_priv(sh);
+
+ scsi_remove_host(sh);
+ wd719x_destroy(wd);
+ pci_iounmap(pdev, wd->base);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+
+ scsi_host_put(sh);
+}
+
+static DEFINE_PCI_DEVICE_TABLE(wd719x_pci_table) = {
+ { PCI_DEVICE(PCI_VENDOR_ID_WD, 0x3296) },
+ {}
+};
+
+MODULE_DEVICE_TABLE(pci, wd719x_pci_table);
+
+static struct pci_driver wd719x_pci_driver = {
+ .name = "wd719x",
+ .id_table = wd719x_pci_table,
+ .probe = wd719x_pci_probe,
+ .remove = wd719x_pci_remove,
+};
+
+static int __init wd719x_init(void)
+{
+ return pci_register_driver(&wd719x_pci_driver);
+}
+
+static void __exit wd719x_exit(void)
+{
+ pci_unregister_driver(&wd719x_pci_driver);
+}
+
+module_init(wd719x_init);
+module_exit(wd719x_exit);
+
+MODULE_DESCRIPTION("Western Digital WD7193/7197/7296 SCSI driver");
+MODULE_AUTHOR("Ondrej Zary, Aaron Dewell, Juergen Gaertner");
+MODULE_LICENSE("GPL");
+MODULE_FIRMWARE("wd719x-wcs.bin");
+MODULE_FIRMWARE("wd719x-risc.bin");
diff --git a/drivers/scsi/wd719x.h b/drivers/scsi/wd719x.h
new file mode 100644
index 0000000..185e30e
--- /dev/null
+++ b/drivers/scsi/wd719x.h
@@ -0,0 +1,249 @@
+#ifndef _WD719X_H_
+#define _WD719X_H_
+
+#define WD719X_SG 255 /* Scatter/gather size */
+#define WD719X_CMD_PER_LUN 1 /* We should be able to do linked commands, but
+ * this is 1 for now to be safe. */
+
+struct wd719x_sglist {
+ __le32 ptr;
+ __le32 length;
+} __packed;
+
+enum wd719x_card_type {
+ WD719X_TYPE_UNKNOWN = 0,
+ WD719X_TYPE_7193,
+ WD719X_TYPE_7197,
+ WD719X_TYPE_7296,
+};
+
+union wd719x_regs {
+ __le32 all; /* All Status at once */
+ struct {
+ u8 OPC; /* Opcode register */
+ u8 SCSI; /* SCSI Errors */
+ u8 SUE; /* Spider unique Errors */
+ u8 INT; /* Interrupt Status */
+ } bytes;
+};
+
+/* Spider Command Block (SCB) */
+struct wd719x_scb {
+ __le32 Int_SCB; /* 00-03 Internal SCB link pointer (must be cleared) */
+ u8 SCB_opcode; /* 04 SCB Command opcode */
+ u8 CDB_tag; /* 05 SCSI Tag byte for CDB queues (0 if untagged) */
+ u8 lun; /* 06 SCSI LUN */
+ u8 devid; /* 07 SCSI Device ID */
+ u8 CDB[16]; /* 08-23 SCSI CDB (16 bytes as defined by ANSI spec. */
+ __le32 data_p; /* 24-27 Data transfer address (or SG list address) */
+ __le32 data_length; /* 28-31 Data transfer Length (or SG list length) */
+ __le32 CDB_link; /* 32-35 SCSI CDB Link Ptr */
+ __le32 sense_buf; /* 36-39 Auto request sense buffer address */
+ u8 sense_buf_length;/* 40 Auto request sense transfer length */
+ u8 reserved; /* 41 reserved */
+ u8 SCB_options; /* 42 SCB-options */
+ u8 SCB_tag_msg; /* 43 Tagged messages options */
+ /* Not filled in by host */
+ __le32 req_ptr; /* 44-47 Ptr to Host Request returned on interrupt */
+ u8 host_opcode; /* 48 Host Command Opcode (same as AMR_00) */
+ u8 scsi_stat; /* 49 SCSI Status returned */
+ u8 ret_error; /* 50 SPIDER Unique Error Code returned (SUE) */
+ u8 int_stat; /* 51 Message u8 / Interrupt Status byte returned */
+ __le32 transferred; /* 52-55 Bytes Transferred */
+ u8 last_trans[3]; /* 56-58 Bytes Transferred in last session */
+ u8 length; /* 59 SCSI Messages Length (1-8) */
+ u8 sync_offset; /* 60 Synchronous offset */
+ u8 sync_rate; /* 61 Synchronous rate */
+ u8 flags[2]; /* 62-63 SCB specific flags (local to each thread) */
+ /* everything below is for driver use (not used by card) */
+ dma_addr_t phys; /* bus address of the SCB */
+ struct scsi_cmnd *cmd; /* a copy of the pointer we were passed */
+ struct list_head list;
+ struct wd719x_sglist sg_list[WD719X_SG] __aligned(8); /* SG list */
+} __packed;
+
+struct wd719x {
+ struct Scsi_Host *sh; /* pointer to host structure */
+ struct pci_dev *pdev;
+ void __iomem *base;
+ enum wd719x_card_type type; /* type of card */
+ void *fw_virt; /* firmware buffer CPU address */
+ dma_addr_t fw_phys; /* firmware buffer bus address */
+ size_t fw_size; /* firmware buffer size */
+ struct wd719x_host_param *params; /* host parameters (EEPROM) */
+ dma_addr_t params_phys; /* host parameters bus address */
+ void *hash_virt; /* hash table CPU address */
+ dma_addr_t hash_phys; /* hash table bus address */
+ struct list_head active_scbs;
+ struct list_head free_scbs;
+};
+
+/* timeout delays in microsecs */
+#define WD719X_WAIT_FOR_CMD_READY 500
+#define WD719X_WAIT_FOR_RISC 2000
+#define WD719X_WAIT_FOR_SCSI_RESET 3000000
+
+/* All commands except 0x00 generate an interrupt */
+#define WD719X_CMD_READY 0x00 /* Command register ready (or noop) */
+#define WD719X_CMD_INIT_RISC 0x01 /* Initialize RISC */
+/* 0x02 is reserved */
+#define WD719X_CMD_BUSRESET 0x03 /* Assert SCSI bus reset */
+#define WD719X_CMD_READ_FIRMVER 0x04 /* Read the Firmware Revision */
+#define WD719X_CMD_ECHO_BYTES 0x05 /* Echo command bytes (DW) */
+/* 0x06 is reserved */
+/* 0x07 is reserved */
+#define WD719X_CMD_GET_PARAM 0x08 /* Get programmable parameters */
+#define WD719X_CMD_SET_PARAM 0x09 /* Set programmable parameters */
+#define WD719X_CMD_SLEEP 0x0a /* Put SPIDER to sleep */
+#define WD719X_CMD_READ_INIT 0x0b /* Read initialization parameters */
+#define WD719X_CMD_RESTORE_INIT 0x0c /* Restore initialization parameters */
+/* 0x0d is reserved */
+/* 0x0e is reserved */
+/* 0x0f is reserved */
+#define WD719X_CMD_ABORT_TAG 0x10 /* Send Abort tag message to target */
+#define WD719X_CMD_ABORT 0x11 /* Send Abort message to target */
+#define WD719X_CMD_RESET 0x12 /* Send Reset message to target */
+#define WD719X_CMD_INIT_SCAM 0x13 /* Initiate SCAM */
+#define WD719X_CMD_GET_SYNC 0x14 /* Get synchronous rates */
+#define WD719X_CMD_SET_SYNC 0x15 /* Set synchronous rates */
+#define WD719X_CMD_GET_WIDTH 0x16 /* Get SCSI bus width */
+#define WD719X_CMD_SET_WIDTH 0x17 /* Set SCSI bus width */
+#define WD719X_CMD_GET_TAGS 0x18 /* Get tag flags */
+#define WD719X_CMD_SET_TAGS 0x19 /* Set tag flags */
+#define WD719X_CMD_GET_PARAM2 0x1a /* Get programmable params (format 2) */
+#define WD719X_CMD_SET_PARAM2 0x1b /* Set programmable params (format 2) */
+/* Commands with request pointers (mailbox) */
+#define WD719X_CMD_PROCESS_SCB 0x80 /* Process SCSI Control Block (SCB) */
+/* No interrupt generated on acceptance of SCB pointer */
+
+/* interrupt status defines */
+#define WD719X_INT_NONE 0x00 /* No interrupt pending */
+#define WD719X_INT_NOERRORS 0x01 /* Command completed with no errors */
+#define WD719X_INT_LINKNOERRORS 0x02 /* link cmd completed with no errors */
+#define WD719X_INT_LINKNOSTATUS 0x03 /* link cmd completed with no flag set */
+#define WD719X_INT_ERRORSLOGGED 0x04 /* cmd completed with errors logged */
+#define WD719X_INT_SPIDERFAILED 0x05 /* cmd failed without valid SCSI status */
+#define WD719X_INT_BADINT 0x80 /* unsolicited interrupt */
+#define WD719X_INT_PIOREADY 0xf0 /* data ready for PIO output */
+
+/* Spider Unique Error Codes (SUE) */
+#define WD719X_SUE_NOERRORS 0x00 /* No errors detected by SPIDER */
+#define WD719X_SUE_REJECTED 0x01 /* Command Rejected (bad opcode/param) */
+#define WD719X_SUE_SCBQFULL 0x02 /* SCB queue full */
+/* 0x03 is reserved */
+#define WD719X_SUE_TERM 0x04 /* Host terminated SCB via primative cmd */
+#define WD719X_SUE_CHAN1PAR 0x05 /* PCI Channel 1 parity error occurred */
+#define WD719X_SUE_CHAN1ABORT 0x06 /* PCI Channel 1 system abort occurred */
+#define WD719X_SUE_CHAN23PAR 0x07 /* PCI Channel 2/3 parity error occurred */
+#define WD719X_SUE_CHAN23ABORT 0x08 /* PCI Channel 2/3 system abort occurred */
+#define WD719X_SUE_TIMEOUT 0x10 /* Selection/reselection timeout */
+#define WD719X_SUE_RESET 0x11 /* SCSI bus reset occurred */
+#define WD719X_SUE_BUSERROR 0x12 /* SCSI bus error */
+#define WD719X_SUE_WRONGWAY 0x13 /* Wrong data transfer dir set by target */
+#define WD719X_SUE_BADPHASE 0x14 /* SCSI phase illegal or unexpected */
+#define WD719X_SUE_TOOLONG 0x15 /* target requested too much data */
+#define WD719X_SUE_BUSFREE 0x16 /* Unexpected SCSI bus free */
+#define WD719X_SUE_ARSDONE 0x17 /* Auto request sense executed */
+#define WD719X_SUE_IGNORED 0x18 /* SCSI message was ignored by target */
+#define WD719X_SUE_WRONGTAGS 0x19 /* Tagged SCB & tags off (or vice versa) */
+#define WD719X_SUE_BADTAGS 0x1a /* Wrong tag message type for target */
+#define WD719X_SUE_NOSCAMID 0x1b /* No SCAM soft ID available */
+
+/* code sizes */
+#define WD719X_HASH_TABLE_SIZE 4096
+
+/* Advanced Mode Registers */
+/* Regs 0x00..0x1f are for Advanced Mode of the card (RISC is running). */
+#define WD719X_AMR_COMMAND 0x00
+#define WD719X_AMR_CMD_PARAM 0x01
+#define WD719X_AMR_CMD_PARAM_2 0x02
+#define WD719X_AMR_CMD_PARAM_3 0x03
+#define WD719X_AMR_SCB_IN 0x04
+
+#define WD719X_AMR_BIOS_SHARE_INT 0x0f
+
+#define WD719X_AMR_SCB_OUT 0x18
+#define WD719X_AMR_OP_CODE 0x1c
+#define WD719X_AMR_SCSI_STATUS 0x1d
+#define WD719X_AMR_SCB_ERROR 0x1e
+#define WD719X_AMR_INT_STATUS 0x1f
+
+#define WD719X_DISABLE_INT 0x80
+
+/* SCB flags */
+#define WD719X_SCB_FLAGS_CHECK_DIRECTION 0x01
+#define WD719X_SCB_FLAGS_PCI_TO_SCSI 0x02
+#define WD719X_SCB_FLAGS_AUTO_REQUEST_SENSE 0x10
+#define WD719X_SCB_FLAGS_DO_SCATTER_GATHER 0x20
+#define WD719X_SCB_FLAGS_NO_DISCONNECT 0x40
+
+/* PCI Registers used for reset, initial code download */
+/* Regs 0x20..0x3f are for Normal (DOS) mode (RISC is asleep). */
+#define WD719X_PCI_GPIO_CONTROL 0x3C
+#define WD719X_PCI_GPIO_DATA 0x3D
+#define WD719X_PCI_PORT_RESET 0x3E
+#define WD719X_PCI_MODE_SELECT 0x3F
+
+#define WD719X_PCI_EXTERNAL_ADDR 0x60
+#define WD719X_PCI_INTERNAL_ADDR 0x64
+#define WD719X_PCI_DMA_TRANSFER_SIZE 0x66
+#define WD719X_PCI_CHANNEL2_3CMD 0x68
+#define WD719X_PCI_CHANNEL2_3STATUS 0x69
+
+#define WD719X_GPIO_ID_BITS 0x0a
+#define WD719X_PRAM_BASE_ADDR 0x00
+
+/* codes written to or read from the card */
+#define WD719X_PCI_RESET 0x01
+#define WD719X_ENABLE_ADVANCE_MODE 0x01
+
+#define WD719X_START_CHANNEL2_3DMA 0x17
+#define WD719X_START_CHANNEL2_3DONE 0x01
+#define WD719X_START_CHANNEL2_3ABORT 0x20
+
+/* 33C296 GPIO bits for EEPROM pins */
+#define WD719X_EE_DI (1 << 1)
+#define WD719X_EE_CS (1 << 2)
+#define WD719X_EE_CLK (1 << 3)
+#define WD719X_EE_DO (1 << 4)
+
+/* EEPROM contents */
+struct wd719x_eeprom_header {
+ u8 sig1;
+ u8 sig2;
+ u8 version;
+ u8 checksum;
+ u8 cfg_offset;
+ u8 cfg_size;
+ u8 setup_offset;
+ u8 setup_size;
+} __packed;
+
+#define WD719X_EE_SIG1 0
+#define WD719X_EE_SIG2 1
+#define WD719X_EE_VERSION 2
+#define WD719X_EE_CHECKSUM 3
+#define WD719X_EE_CFG_OFFSET 4
+#define WD719X_EE_CFG_SIZE 5
+#define WD719X_EE_SETUP_OFFSET 6
+#define WD719X_EE_SETUP_SIZE 7
+
+#define WD719X_EE_SCSI_ID_MASK 0xf
+
+/* SPIDER Host Parameters Block (=EEPROM configuration block) */
+struct wd719x_host_param {
+ u8 ch_1_th; /* FIFO threshold */
+ u8 scsi_conf; /* SCSI configuration */
+ u8 own_scsi_id; /* controller SCSI ID */
+ u8 sel_timeout; /* selection timeout*/
+ u8 sleep_timer; /* seep timer */
+ __le16 cdb_size;/* CDB size groups */
+ __le16 tag_en; /* Tag msg enables (ID 0-15) */
+ u8 scsi_pad; /* SCSI pad control */
+ __le32 wide; /* WIDE msg options (ID 0-15) */
+ __le32 sync; /* SYNC msg options (ID 0-15) */
+ u8 soft_mask; /* soft error mask */
+ u8 unsol_mask; /* unsolicited error mask */
+} __packed;
+
+#endif /* _WD719X_H_ */
--
Ondrej Zary
Add read-only support for EEPROMs configured in 8-bit mode (ORG pin connected
to GND).
This will be used by wd719x driver.
Signed-off-by: Ondrej Zary <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
---
drivers/misc/eeprom/eeprom_93cx6.c | 62 +++++++++++++++++++++++++++++++++++-
include/linux/eeprom_93cx6.h | 4 +++
2 files changed, 65 insertions(+), 1 deletion(-)
diff --git a/drivers/misc/eeprom/eeprom_93cx6.c b/drivers/misc/eeprom/eeprom_93cx6.c
index 0ff4b02..0cf2c9d 100644
--- a/drivers/misc/eeprom/eeprom_93cx6.c
+++ b/drivers/misc/eeprom/eeprom_93cx6.c
@@ -170,7 +170,7 @@ static void eeprom_93cx6_read_bits(struct eeprom_93cx6 *eeprom,
}
/**
- * eeprom_93cx6_read - Read multiple words from eeprom
+ * eeprom_93cx6_read - Read a word from eeprom
* @eeprom: Pointer to eeprom structure
* @word: Word index from where we should start reading
* @data: target pointer where the information will have to be stored
@@ -235,6 +235,66 @@ void eeprom_93cx6_multiread(struct eeprom_93cx6 *eeprom, const u8 word,
EXPORT_SYMBOL_GPL(eeprom_93cx6_multiread);
/**
+ * eeprom_93cx6_readb - Read a byte from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @word: Byte index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ *
+ * This function will read a byte of the eeprom data
+ * into the given data pointer.
+ */
+void eeprom_93cx6_readb(struct eeprom_93cx6 *eeprom, const u8 byte,
+ u8 *data)
+{
+ u16 command;
+ u16 tmp;
+
+ /*
+ * Initialize the eeprom register
+ */
+ eeprom_93cx6_startup(eeprom);
+
+ /*
+ * Select the read opcode and the byte to be read.
+ */
+ command = (PCI_EEPROM_READ_OPCODE << (eeprom->width + 1)) | byte;
+ eeprom_93cx6_write_bits(eeprom, command,
+ PCI_EEPROM_WIDTH_OPCODE + eeprom->width + 1);
+
+ /*
+ * Read the requested 8 bits.
+ */
+ eeprom_93cx6_read_bits(eeprom, &tmp, 8);
+ *data = tmp & 0xff;
+
+ /*
+ * Cleanup eeprom register.
+ */
+ eeprom_93cx6_cleanup(eeprom);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_readb);
+
+/**
+ * eeprom_93cx6_multireadb - Read multiple bytes from eeprom
+ * @eeprom: Pointer to eeprom structure
+ * @byte: Index from where we should start reading
+ * @data: target pointer where the information will have to be stored
+ * @words: Number of bytes that should be read.
+ *
+ * This function will read all requested bytes from the eeprom,
+ * this is done by calling eeprom_93cx6_readb() multiple times.
+ */
+void eeprom_93cx6_multireadb(struct eeprom_93cx6 *eeprom, const u8 byte,
+ u8 *data, const u16 bytes)
+{
+ unsigned int i;
+
+ for (i = 0; i < bytes; i++)
+ eeprom_93cx6_readb(eeprom, byte + i, &data[i]);
+}
+EXPORT_SYMBOL_GPL(eeprom_93cx6_multireadb);
+
+/**
* eeprom_93cx6_wren - set the write enable state
* @eeprom: Pointer to eeprom structure
* @enable: true to enable writes, otherwise disable writes
diff --git a/include/linux/eeprom_93cx6.h b/include/linux/eeprom_93cx6.h
index e50f98b..eb0b198 100644
--- a/include/linux/eeprom_93cx6.h
+++ b/include/linux/eeprom_93cx6.h
@@ -75,6 +75,10 @@ extern void eeprom_93cx6_read(struct eeprom_93cx6 *eeprom,
const u8 word, u16 *data);
extern void eeprom_93cx6_multiread(struct eeprom_93cx6 *eeprom,
const u8 word, __le16 *data, const u16 words);
+extern void eeprom_93cx6_readb(struct eeprom_93cx6 *eeprom,
+ const u8 byte, u8 *data);
+extern void eeprom_93cx6_multireadb(struct eeprom_93cx6 *eeprom,
+ const u8 byte, u8 *data, const u16 bytes);
extern void eeprom_93cx6_wren(struct eeprom_93cx6 *eeprom, bool enable);
--
Ondrej Zary
On 11/24/2014 11:24 PM, Ondrej Zary wrote:
> Introduce wd719x, a driver for Western Digital WD7193, WD7197 and WD7296 PCI
> SCSI controllers based on WD33C296A chip.
> Tested with WD7193 card.
>
> Reviewed-by: Christoph Hellwig <[email protected]>
> Signed-off-by: Ondrej Zary <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Cheers,
Hannes
--
Dr. Hannes Reinecke zSeries & Storage
[email protected] +49 911 74053 688
SUSE LINUX GmbH, Maxfeldstr. 5, 90409 N?rnberg
GF: J. Hawn, J. Guild, F. Imend?rffer, HRB 21284 (AG N?rnberg)
On 11/24/2014 11:24 PM, Ondrej Zary wrote:
> Add documentation and script to obtain required firmware.
>
> Signed-off-by: Ondrej Zary <[email protected]>
> ---
> Documentation/scsi/wd719x.txt | 21 +++++++++++++++++++++
> 1 file changed, 21 insertions(+)
> create mode 100644 Documentation/scsi/wd719x.txt
>
> diff --git a/Documentation/scsi/wd719x.txt b/Documentation/scsi/wd719x.txt
> new file mode 100644
> index 0000000..0816b02
> --- /dev/null
> +++ b/Documentation/scsi/wd719x.txt
> @@ -0,0 +1,21 @@
> +Driver for Western Digital WD7193, WD7197 and WD7296 SCSI cards
> +---------------------------------------------------------------
> +
> +The card requires firmware that can be cut out of the Windows NT driver that
> +can be downloaded from WD at:
> +http://support.wdc.com/product/download.asp?groupid=801&sid=27&lang=en
> +
> +There is no license anywhere in the file or on the page - so the firmware
> +probably cannot be added to linux-firmware.
> +
> +This script downloads and extracts the firmware, creating wd719x-risc.bin and
> +d719x-wcs.bin files. Put them in /lib/firmware/.
> +
> +#!/bin/sh
> +wget http://support.wdc.com/download/archive/pciscsi.exe
> +lha xi pciscsi.exe pci-scsi.exe
> +lha xi pci-scsi.exe nt/wd7296a.sys
> +rm pci-scsi.exe
> +dd if=wd7296a.sys of=wd719x-risc.bin bs=1 skip=5760 count=14336
> +dd if=wd7296a.sys of=wd719x-wcs.bin bs=1 skip=20096 count=514
> +rm wd7296a.sys
>
Reviewed-by: Hannes Reinecke <[email protected]>
Cheers,
Hannes
--
Dr. Hannes Reinecke zSeries & Storage
[email protected] +49 911 74053 688
SUSE LINUX GmbH, Maxfeldstr. 5, 90409 N?rnberg
GF: J. Hawn, J. Guild, F. Imend?rffer, HRB 21284 (AG N?rnberg)
Thanks, applied the series to drivers-for-3.19.
I had to add an include of <linux/interrupt.h> to make it compile on my
setup, though.