Rewrite the blackfin CAN driver into common style
V4 changes: remove unused variable in patch 2/2
V3 changes: remove redundant cast in patch 2/2
V2 changes: split patch into two parts
V1 changes: rewrite code into common style
Signed-off-by: Aaron Wu <[email protected]>
---
drivers/net/can/bfin_can.c | 126 +++++++++++++++++++++-----------------------
1 file changed, 60 insertions(+), 66 deletions(-)
diff --git a/drivers/net/can/bfin_can.c b/drivers/net/can/bfin_can.c
index 417d5099..0a5eff4 100644
--- a/drivers/net/can/bfin_can.c
+++ b/drivers/net/can/bfin_can.c
@@ -78,8 +78,8 @@ static int bfin_can_set_bittiming(struct net_device *dev)
if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
timing |= SAM;
- bfin_write(®->clock, clk);
- bfin_write(®->timing, timing);
+ writew(clk, ®->clock);
+ writew(timing, ®->timing);
netdev_info(dev, "setting CLOCK=0x%04x TIMING=0x%04x\n", clk, timing);
@@ -94,16 +94,14 @@ static void bfin_can_set_reset_mode(struct net_device *dev)
int i;
/* disable interrupts */
- bfin_write(®->mbim1, 0);
- bfin_write(®->mbim2, 0);
- bfin_write(®->gim, 0);
+ writew(0, ®->mbim1);
+ writew(0, ®->mbim2);
+ writew(0, ®->gim);
/* reset can and enter configuration mode */
- bfin_write(®->control, SRS | CCR);
- SSYNC();
- bfin_write(®->control, CCR);
- SSYNC();
- while (!(bfin_read(®->control) & CCA)) {
+ writew(SRS | CCR, ®->control);
+ writew(CCR, ®->control);
+ while (!(readw(®->control) & CCA)) {
udelay(10);
if (--timeout == 0) {
netdev_err(dev, "fail to enter configuration mode\n");
@@ -116,34 +114,33 @@ static void bfin_can_set_reset_mode(struct net_device *dev)
* by writing to CAN Mailbox Configuration Registers 1 and 2
* For all bits: 0 - Mailbox disabled, 1 - Mailbox enabled
*/
- bfin_write(®->mc1, 0);
- bfin_write(®->mc2, 0);
+ writew(0, ®->mc1);
+ writew(0, ®->mc2);
/* Set Mailbox Direction */
- bfin_write(®->md1, 0xFFFF); /* mailbox 1-16 are RX */
- bfin_write(®->md2, 0); /* mailbox 17-32 are TX */
+ writew(0xFFFF, ®->md1); /* mailbox 1-16 are RX */
+ writew(0, ®->md2); /* mailbox 17-32 are TX */
/* RECEIVE_STD_CHL */
for (i = 0; i < 2; i++) {
- bfin_write(®->chl[RECEIVE_STD_CHL + i].id0, 0);
- bfin_write(®->chl[RECEIVE_STD_CHL + i].id1, AME);
- bfin_write(®->chl[RECEIVE_STD_CHL + i].dlc, 0);
- bfin_write(®->msk[RECEIVE_STD_CHL + i].amh, 0x1FFF);
- bfin_write(®->msk[RECEIVE_STD_CHL + i].aml, 0xFFFF);
+ writew(0, ®->chl[RECEIVE_STD_CHL + i].id0);
+ writew(AME, ®->chl[RECEIVE_STD_CHL + i].id1);
+ writew(0, ®->chl[RECEIVE_STD_CHL + i].dlc);
+ writew(0x1FFF, ®->msk[RECEIVE_STD_CHL + i].amh);
+ writew(0xFFFF, ®->msk[RECEIVE_STD_CHL + i].aml);
}
/* RECEIVE_EXT_CHL */
for (i = 0; i < 2; i++) {
- bfin_write(®->chl[RECEIVE_EXT_CHL + i].id0, 0);
- bfin_write(®->chl[RECEIVE_EXT_CHL + i].id1, AME | IDE);
- bfin_write(®->chl[RECEIVE_EXT_CHL + i].dlc, 0);
- bfin_write(®->msk[RECEIVE_EXT_CHL + i].amh, 0x1FFF);
- bfin_write(®->msk[RECEIVE_EXT_CHL + i].aml, 0xFFFF);
+ writew(0, ®->chl[RECEIVE_EXT_CHL + i].id0);
+ writew(AME | IDE, ®->chl[RECEIVE_EXT_CHL + i].id1);
+ writew(0, ®->chl[RECEIVE_EXT_CHL + i].dlc);
+ writew(0x1FFF, ®->msk[RECEIVE_EXT_CHL + i].amh);
+ writew(0xFFFF, ®->msk[RECEIVE_EXT_CHL + i].aml);
}
- bfin_write(®->mc2, BIT(TRANSMIT_CHL - 16));
- bfin_write(®->mc1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
- SSYNC();
+ writew(BIT(TRANSMIT_CHL - 16), ®->mc2);
+ writew(BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL), ®->mc1);
priv->can.state = CAN_STATE_STOPPED;
}
@@ -157,9 +154,9 @@ static void bfin_can_set_normal_mode(struct net_device *dev)
/*
* leave configuration mode
*/
- bfin_write(®->control, bfin_read(®->control) & ~CCR);
+ writew(readw(®->control) & ~CCR, ®->control);
- while (bfin_read(®->status) & CCA) {
+ while (readw(®->status) & CCA) {
udelay(10);
if (--timeout == 0) {
netdev_err(dev, "fail to leave configuration mode\n");
@@ -170,26 +167,25 @@ static void bfin_can_set_normal_mode(struct net_device *dev)
/*
* clear _All_ tx and rx interrupts
*/
- bfin_write(®->mbtif1, 0xFFFF);
- bfin_write(®->mbtif2, 0xFFFF);
- bfin_write(®->mbrif1, 0xFFFF);
- bfin_write(®->mbrif2, 0xFFFF);
+ writew(0xFFFF, ®->mbtif1);
+ writew(0xFFFF, ®->mbtif2);
+ writew(0xFFFF, ®->mbrif1);
+ writew(0xFFFF, ®->mbrif2);
/*
* clear global interrupt status register
*/
- bfin_write(®->gis, 0x7FF); /* overwrites with '1' */
+ writew(0x7FF, ®->gis); /* overwrites with '1' */
/*
* Initialize Interrupts
* - set bits in the mailbox interrupt mask register
* - global interrupt mask
*/
- bfin_write(®->mbim1, BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL));
- bfin_write(®->mbim2, BIT(TRANSMIT_CHL - 16));
+ writew(BIT(RECEIVE_STD_CHL) + BIT(RECEIVE_EXT_CHL), ®->mbim1);
+ writew(BIT(TRANSMIT_CHL - 16), ®->mbim2);
- bfin_write(®->gim, EPIM | BOIM | RMLIM);
- SSYNC();
+ writew(EPIM | BOIM | RMLIM, ®->gim);
}
static void bfin_can_start(struct net_device *dev)
@@ -226,7 +222,7 @@ static int bfin_can_get_berr_counter(const struct net_device *dev,
struct bfin_can_priv *priv = netdev_priv(dev);
struct bfin_can_regs __iomem *reg = priv->membase;
- u16 cec = bfin_read(®->cec);
+ u16 cec = readw(®->cec);
bec->txerr = cec >> 8;
bec->rxerr = cec;
@@ -252,28 +248,28 @@ static int bfin_can_start_xmit(struct sk_buff *skb, struct net_device *dev)
/* fill id */
if (id & CAN_EFF_FLAG) {
- bfin_write(®->chl[TRANSMIT_CHL].id0, id);
+ writew(id, ®->chl[TRANSMIT_CHL].id0);
val = ((id & 0x1FFF0000) >> 16) | IDE;
} else
val = (id << 2);
if (id & CAN_RTR_FLAG)
val |= RTR;
- bfin_write(®->chl[TRANSMIT_CHL].id1, val | AME);
+ writew(val | AME, ®->chl[TRANSMIT_CHL].id1);
/* fill payload */
for (i = 0; i < 8; i += 2) {
val = ((7 - i) < dlc ? (data[7 - i]) : 0) +
((6 - i) < dlc ? (data[6 - i] << 8) : 0);
- bfin_write(®->chl[TRANSMIT_CHL].data[i], val);
+ writew(val, ®->chl[TRANSMIT_CHL].data[i]);
}
/* fill data length code */
- bfin_write(®->chl[TRANSMIT_CHL].dlc, dlc);
+ writew(dlc, ®->chl[TRANSMIT_CHL].dlc);
can_put_echo_skb(skb, dev, 0);
/* set transmit request */
- bfin_write(®->trs2, BIT(TRANSMIT_CHL - 16));
+ writew(BIT(TRANSMIT_CHL - 16), ®->trs2);
return 0;
}
@@ -296,26 +292,26 @@ static void bfin_can_rx(struct net_device *dev, u16 isrc)
/* get id */
if (isrc & BIT(RECEIVE_EXT_CHL)) {
/* extended frame format (EFF) */
- cf->can_id = ((bfin_read(®->chl[RECEIVE_EXT_CHL].id1)
+ cf->can_id = ((readw(®->chl[RECEIVE_EXT_CHL].id1)
& 0x1FFF) << 16)
- + bfin_read(®->chl[RECEIVE_EXT_CHL].id0);
+ + readw(®->chl[RECEIVE_EXT_CHL].id0);
cf->can_id |= CAN_EFF_FLAG;
obj = RECEIVE_EXT_CHL;
} else {
/* standard frame format (SFF) */
- cf->can_id = (bfin_read(®->chl[RECEIVE_STD_CHL].id1)
+ cf->can_id = (readw(®->chl[RECEIVE_STD_CHL].id1)
& 0x1ffc) >> 2;
obj = RECEIVE_STD_CHL;
}
- if (bfin_read(®->chl[obj].id1) & RTR)
+ if (readw(®->chl[obj].id1) & RTR)
cf->can_id |= CAN_RTR_FLAG;
/* get data length code */
- cf->can_dlc = get_can_dlc(bfin_read(®->chl[obj].dlc) & 0xF);
+ cf->can_dlc = get_can_dlc(readw(®->chl[obj].dlc) & 0xF);
/* get payload */
for (i = 0; i < 8; i += 2) {
- val = bfin_read(®->chl[obj].data[i]);
+ val = readw(®->chl[obj].data[i]);
cf->data[7 - i] = (7 - i) < cf->can_dlc ? val : 0;
cf->data[6 - i] = (6 - i) < cf->can_dlc ? (val >> 8) : 0;
}
@@ -368,7 +364,7 @@ static int bfin_can_err(struct net_device *dev, u16 isrc, u16 status)
if (state != priv->can.state && (state == CAN_STATE_ERROR_WARNING ||
state == CAN_STATE_ERROR_PASSIVE)) {
- u16 cec = bfin_read(®->cec);
+ u16 cec = readw(®->cec);
u8 rxerr = cec;
u8 txerr = cec >> 8;
@@ -419,23 +415,23 @@ static irqreturn_t bfin_can_interrupt(int irq, void *dev_id)
struct net_device_stats *stats = &dev->stats;
u16 status, isrc;
- if ((irq == priv->tx_irq) && bfin_read(®->mbtif2)) {
+ if ((irq == priv->tx_irq) && readw(®->mbtif2)) {
/* transmission complete interrupt */
- bfin_write(®->mbtif2, 0xFFFF);
+ writew(0xFFFF, ®->mbtif2);
stats->tx_packets++;
- stats->tx_bytes += bfin_read(®->chl[TRANSMIT_CHL].dlc);
+ stats->tx_bytes += readw(®->chl[TRANSMIT_CHL].dlc);
can_get_echo_skb(dev, 0);
netif_wake_queue(dev);
- } else if ((irq == priv->rx_irq) && bfin_read(®->mbrif1)) {
+ } else if ((irq == priv->rx_irq) && readw(®->mbrif1)) {
/* receive interrupt */
- isrc = bfin_read(®->mbrif1);
- bfin_write(®->mbrif1, 0xFFFF);
+ isrc = readw(®->mbrif1);
+ writew(0xFFFF, ®->mbrif1);
bfin_can_rx(dev, isrc);
- } else if ((irq == priv->err_irq) && bfin_read(®->gis)) {
+ } else if ((irq == priv->err_irq) && readw(®->gis)) {
/* error interrupt */
- isrc = bfin_read(®->gis);
- status = bfin_read(®->esr);
- bfin_write(®->gis, 0x7FF);
+ isrc = readw(®->gis);
+ status = readw(®->esr);
+ writew(0x7FF, ®->gis);
bfin_can_err(dev, isrc, status);
} else {
return IRQ_NONE;
@@ -640,9 +636,8 @@ static int bfin_can_suspend(struct platform_device *pdev, pm_message_t mesg)
if (netif_running(dev)) {
/* enter sleep mode */
- bfin_write(®->control, bfin_read(®->control) | SMR);
- SSYNC();
- while (!(bfin_read(®->intr) & SMACK)) {
+ writew(readw(®->control) | SMR, ®->control);
+ while (!(readw(®->intr) & SMACK)) {
udelay(10);
if (--timeout == 0) {
netdev_err(dev, "fail to enter sleep mode\n");
@@ -662,8 +657,7 @@ static int bfin_can_resume(struct platform_device *pdev)
if (netif_running(dev)) {
/* leave sleep mode */
- bfin_write(®->intr, 0);
- SSYNC();
+ writew(0, ®->intr);
}
return 0;
--
1.7.9.5
Rewrite the blackfin CAN driver into common style
V4 changes: remove unused variable in patch 2/2
V3 changes: remove redundant cast in patch 2/2
V2 changes: split patch into two parts
V1 changes: rewrite code into common style
Signed-off-by: Aaron Wu <[email protected]>
---
drivers/net/can/bfin_can.c | 22 ++++++++--------------
1 file changed, 8 insertions(+), 14 deletions(-)
diff --git a/drivers/net/can/bfin_can.c b/drivers/net/can/bfin_can.c
index 0a5eff4..0209c14 100644
--- a/drivers/net/can/bfin_can.c
+++ b/drivers/net/can/bfin_can.c
@@ -551,16 +551,10 @@ static int bfin_can_probe(struct platform_device *pdev)
goto exit;
}
- if (!request_mem_region(res_mem->start, resource_size(res_mem),
- dev_name(&pdev->dev))) {
- err = -EBUSY;
- goto exit;
- }
-
/* request peripheral pins */
err = peripheral_request_list(pdata, dev_name(&pdev->dev));
if (err)
- goto exit_mem_release;
+ goto exit;
dev = alloc_bfin_candev();
if (!dev) {
@@ -569,7 +563,13 @@ static int bfin_can_probe(struct platform_device *pdev)
}
priv = netdev_priv(dev);
- priv->membase = (void __iomem *)res_mem->start;
+
+ priv->membase = devm_ioremap_resource(&pdev->dev, res_mem);
+ if (IS_ERR(priv->membase)) {
+ dev_err(&pdev->dev, "Cannot map IO\n");
+ return PTR_ERR(priv->membase);
+ }
+
priv->rx_irq = rx_irq->start;
priv->tx_irq = tx_irq->start;
priv->err_irq = err_irq->start;
@@ -601,8 +601,6 @@ exit_candev_free:
free_candev(dev);
exit_peri_pin_free:
peripheral_free_list(pdata);
-exit_mem_release:
- release_mem_region(res_mem->start, resource_size(res_mem));
exit:
return err;
}
@@ -611,15 +609,11 @@ static int bfin_can_remove(struct platform_device *pdev)
{
struct net_device *dev = platform_get_drvdata(pdev);
struct bfin_can_priv *priv = netdev_priv(dev);
- struct resource *res;
bfin_can_set_reset_mode(dev);
unregister_candev(dev);
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- release_mem_region(res->start, resource_size(res));
-
peripheral_free_list(priv->pin_list);
free_candev(dev);
--
1.7.9.5
On 02/05/2015 09:28 AM, Aaron Wu wrote:
> Rewrite the blackfin CAN driver into common style
> V4 changes: remove unused variable in patch 2/2
> V3 changes: remove redundant cast in patch 2/2
> V2 changes: split patch into two parts
> V1 changes: rewrite code into common style
>
> Signed-off-by: Aaron Wu <[email protected]>
The code looks good, the patch description can be improved though.
Please replace the change history by a description what this patch does
and why. For this kind of patch a single sentence would be enough, but
rewrite into common style is to generic. (Same applies to 1/2)
Marc
--
Pengutronix e.K. | Marc Kleine-Budde |
Industrial Linux Solutions | Phone: +49-231-2826-924 |
Vertretung West/Dortmund | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |