return type of wait_for_completion_timeout is unsigned long not int. The
return variable is renamed to reflect its use and the type adjusted to
unsigned long.
Signed-off-by: Nicholas Mc Guire <[email protected]>
---
v2: variable renamed rather than just changing the type as suggested by
Wolfram Sang <[email protected]>. Further the two separate patches
were merged as the changed are conceptually identical.
Patch was only compile tested with axm55xx_defconfig
(implies CONFIG_I2C_AXXIA=y)
Patch is against 3.19.0-rc7 (localversion-next is -next-20150204)
drivers/i2c/busses/i2c-axxia.c | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/drivers/i2c/busses/i2c-axxia.c b/drivers/i2c/busses/i2c-axxia.c
index 768a598..7e45d05 100644
--- a/drivers/i2c/busses/i2c-axxia.c
+++ b/drivers/i2c/busses/i2c-axxia.c
@@ -334,7 +334,7 @@ static int axxia_i2c_xfer_msg(struct axxia_i2c_dev *idev, struct i2c_msg *msg)
u32 int_mask = MST_STATUS_ERR | MST_STATUS_SNS;
u32 rx_xfer, tx_xfer;
u32 addr_1, addr_2;
- int ret;
+ unsigned long timeout;
if (msg->len > 255) {
dev_warn(idev->dev, "unsupported length %u\n", msg->len);
@@ -388,15 +388,15 @@ static int axxia_i2c_xfer_msg(struct axxia_i2c_dev *idev, struct i2c_msg *msg)
i2c_int_enable(idev, int_mask);
- ret = wait_for_completion_timeout(&idev->msg_complete,
- I2C_XFER_TIMEOUT);
+ timeout = wait_for_completion_timeout(&idev->msg_complete,
+ I2C_XFER_TIMEOUT);
i2c_int_disable(idev, int_mask);
if (readl(idev->base + MST_COMMAND) & CMD_BUSY)
dev_warn(idev->dev, "busy after xfer\n");
- if (ret == 0)
+ if (timeout == 0)
idev->msg_err = -ETIMEDOUT;
if (unlikely(idev->msg_err) && idev->msg_err != -ENXIO)
@@ -408,17 +408,17 @@ static int axxia_i2c_xfer_msg(struct axxia_i2c_dev *idev, struct i2c_msg *msg)
static int axxia_i2c_stop(struct axxia_i2c_dev *idev)
{
u32 int_mask = MST_STATUS_ERR | MST_STATUS_SCC;
- int ret;
+ unsigned long timeout;
reinit_completion(&idev->msg_complete);
/* Issue stop */
writel(0xb, idev->base + MST_COMMAND);
i2c_int_enable(idev, int_mask);
- ret = wait_for_completion_timeout(&idev->msg_complete,
- I2C_STOP_TIMEOUT);
+ timeout = wait_for_completion_timeout(&idev->msg_complete,
+ I2C_STOP_TIMEOUT);
i2c_int_disable(idev, int_mask);
- if (ret == 0)
+ if (timeout == 0)
return -ETIMEDOUT;
if (readl(idev->base + MST_COMMAND) & CMD_BUSY)
--
1.7.10.4