This patchset adds support for the regulators found on Qualcomm's
SPMI PMICs. The first patch is the "basic" driver that doesn't have
any non-standard features. The next 4 patches add ways to configure some
of the non-standard features that are generic but aren't supported
in the regulator framework. And the final patch adds support
for the non-standard features and some vendor specific features to
the SPMI regulator driver.
Changes since v1:
* Split driver into standard and non-standard patches to ease review
* New patches to regulator framework for non-standard features
* Added bypass support
* Namespaced macros
* Switch to set_load() ops instead of get_optimum_mode()
* Consolidated range finding code
* Used delay op to calculate how long to delay after setting voltage on FTSMPS
Stephen Boyd (6):
regulator: Add QCOM SPMI regulator driver
regulator: Add system_load constraint
regulator: Add pull down support
regulator: Add soft start support
regulator: Add input current limit support
regulator: qcom-spmi: Add vendor specific configuration
.../bindings/regulator/qcom,spmi-regulator.txt | 183 +++
.../devicetree/bindings/regulator/regulator.txt | 5 +
drivers/regulator/Kconfig | 11 +
drivers/regulator/Makefile | 1 +
drivers/regulator/core.c | 27 +
drivers/regulator/of_regulator.c | 12 +
drivers/regulator/qcom_spmi-regulator.c | 1678 ++++++++++++++++++++
include/linux/regulator/driver.h | 10 +
include/linux/regulator/machine.h | 8 +
9 files changed, 1935 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
create mode 100644 drivers/regulator/qcom_spmi-regulator.c
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Add an SPMI regulator driver for Qualcomm's PM8841, PM8941, and
PM8916 PMICs. This driver is based largely on code from
codeaurora.org[1].
[1] https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/regulator/qpnp-regulator.c?h=msm-3.10
Cc: David Collins <[email protected]>
Cc: <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
---
Changes from v1:
* Dropped custom DT properties
* Added bypass support
* Namespaced macros
* Switch to set_load() ops instead of get_optimum_mode()
.../bindings/regulator/qcom,spmi-regulator.txt | 121 ++
drivers/regulator/Kconfig | 11 +
drivers/regulator/Makefile | 1 +
drivers/regulator/qcom_spmi-regulator.c | 1384 ++++++++++++++++++++
4 files changed, 1517 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
create mode 100644 drivers/regulator/qcom_spmi-regulator.c
diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
new file mode 100644
index 000000000000..75b4604bad07
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -0,0 +1,121 @@
+Qualcomm SPMI Regulators
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,pm8841-regulators"
+ "qcom,pm8916-regulators"
+ "qcom,pm8941-regulators"
+
+- interrupts:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: List of OCP interrupts.
+
+- interrupt-names:
+ Usage: required if 'interrupts' property present
+ Value type: <string-array>
+ Definition: List of strings defining the names of the
+ interrupts in the 'interrupts' property 1-to-1.
+ Supported values are "ocp-<regulator_name>", where
+ <regulator_name> corresponds to a voltage switch
+ type regulator.
+
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_s6-supply:
+- vdd_s7-supply:
+- vdd_s8-supply:
+ Usage: optional (pm8841 only)
+ Value type: <phandle>
+ Definition: Reference to regulator supplying the input pin, as
+ described in the data sheet.
+
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_l1_l3-supply:
+- vdd_l2-supply:
+- vdd_l4_l5_l6-supply:
+- vdd_l7-supply:
+- vdd_l8_l11_l14_l15_l16-supply:
+- vdd_l9_l10_l12_l13_l17_l18-supply:
+ Usage: optional (pm8916 only)
+ Value type: <phandle>
+ Definition: Reference to regulator supplying the input pin, as
+ described in the data sheet.
+
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_l1_l3-supply:
+- vdd_l2_lvs_1_2_3-supply:
+- vdd_l4_l11-supply:
+- vdd_l5_l7-supply:
+- vdd_l6_l12_l14_l15-supply:
+- vdd_l8_l16_l18_19-supply:
+- vdd_l9_l10_l17_l22-supply:
+- vdd_l13_l20_l23_l24-supply:
+- vdd_l21-supply:
+- vin_5vs-supply:
+ Usage: optional (pm8941 only)
+ Value type: <phandle>
+ Definition: Reference to regulator supplying the input pin, as
+ described in the data sheet.
+
+
+The regulator node houses sub-nodes for each regulator within the device. Each
+sub-node is identified using the node's name, with valid values listed for each
+of the PMICs below.
+
+pm8841:
+ s1, s2, s3, s4, s5, s6, s7, s8
+
+pm8916:
+ s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+ l14, l15, l16, l17, l18
+
+pm8941:
+ s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14,
+ l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
+ mvs1, mvs2
+
+The content of each sub-node is defined by the standard binding for regulators -
+see regulator.txt - with additional custom properties described below:
+
+- regulator-initial-mode:
+ Usage: optional
+ Value type: <u32>
+ Descrption: 1 = Set initial mode to high power mode (HPM), also referred
+ to as NPM. HPM consumes more ground current than LPM, but
+ it can source significantly higher load current. HPM is not
+ available on boost type regulators. For voltage switch type
+ regulators, HPM implies that over current protection and
+ soft start are active all the time. 0 = Set initial mode to
+ low power mode (LPM).
+
+Example:
+
+ regulators {
+ compatible = "qcom,pm8941-regulators";
+ vdd_l1_l3-supply = <&s1>;
+
+ s1: s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1400000>;
+ };
+
+ ...
+
+ l1: l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ ....
+ };
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 7707b989a246..441525ab0cec 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -524,6 +524,17 @@ config REGULATOR_QCOM_SMD_RPM
Qualcomm RPM as a module. The module will be named
"qcom_smd-regulator".
+config REGULATOR_QCOM_SPMI
+ tristate "Qualcomm SPMI regulator driver"
+ depends on SPMI || COMPILE_TEST
+ help
+ If you say yes to this option, support will be included for the
+ regulators found in Qualcomm SPMI PMICs.
+
+ Say M here if you want to include support for the regulators on the
+ Qualcomm SPMI PMICs as a module. The module will be named
+ "qcom_spmi-regulator".
+
config REGULATOR_RC5T583
tristate "RICOH RC5T583 Power regulators"
depends on MFD_RC5T583
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index da9be8851e01..b737d30d1476 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -62,6 +62,7 @@ obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
+obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
obj-$(CONFIG_REGULATOR_PWM) += pwm-regulator.o
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
new file mode 100644
index 000000000000..3df635d101c4
--- /dev/null
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -0,0 +1,1384 @@
+/*
+ * Copyright (c) 2012-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/bitops.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/ktime.h>
+#include <linux/regulator/driver.h>
+#include <linux/regmap.h>
+#include <linux/list.h>
+
+/* These types correspond to unique register layouts. */
+enum spmi_regulator_logical_type {
+ SPMI_REGULATOR_LOGICAL_TYPE_SMPS,
+ SPMI_REGULATOR_LOGICAL_TYPE_LDO,
+ SPMI_REGULATOR_LOGICAL_TYPE_VS,
+ SPMI_REGULATOR_LOGICAL_TYPE_BOOST,
+ SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS,
+ SPMI_REGULATOR_LOGICAL_TYPE_BOOST_BYP,
+ SPMI_REGULATOR_LOGICAL_TYPE_LN_LDO,
+ SPMI_REGULATOR_LOGICAL_TYPE_ULT_LO_SMPS,
+ SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS,
+ SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO,
+};
+
+enum spmi_regulator_type {
+ SPMI_REGULATOR_TYPE_BUCK = 0x03,
+ SPMI_REGULATOR_TYPE_LDO = 0x04,
+ SPMI_REGULATOR_TYPE_VS = 0x05,
+ SPMI_REGULATOR_TYPE_BOOST = 0x1b,
+ SPMI_REGULATOR_TYPE_FTS = 0x1c,
+ SPMI_REGULATOR_TYPE_BOOST_BYP = 0x1f,
+ SPMI_REGULATOR_TYPE_ULT_LDO = 0x21,
+ SPMI_REGULATOR_TYPE_ULT_BUCK = 0x22,
+};
+
+enum spmi_regulator_subtype {
+ SPMI_REGULATOR_SUBTYPE_GP_CTL = 0x08,
+ SPMI_REGULATOR_SUBTYPE_RF_CTL = 0x09,
+ SPMI_REGULATOR_SUBTYPE_N50 = 0x01,
+ SPMI_REGULATOR_SUBTYPE_N150 = 0x02,
+ SPMI_REGULATOR_SUBTYPE_N300 = 0x03,
+ SPMI_REGULATOR_SUBTYPE_N600 = 0x04,
+ SPMI_REGULATOR_SUBTYPE_N1200 = 0x05,
+ SPMI_REGULATOR_SUBTYPE_N600_ST = 0x06,
+ SPMI_REGULATOR_SUBTYPE_N1200_ST = 0x07,
+ SPMI_REGULATOR_SUBTYPE_N900_ST = 0x14,
+ SPMI_REGULATOR_SUBTYPE_N300_ST = 0x15,
+ SPMI_REGULATOR_SUBTYPE_P50 = 0x08,
+ SPMI_REGULATOR_SUBTYPE_P150 = 0x09,
+ SPMI_REGULATOR_SUBTYPE_P300 = 0x0a,
+ SPMI_REGULATOR_SUBTYPE_P600 = 0x0b,
+ SPMI_REGULATOR_SUBTYPE_P1200 = 0x0c,
+ SPMI_REGULATOR_SUBTYPE_LN = 0x10,
+ SPMI_REGULATOR_SUBTYPE_LV_P50 = 0x28,
+ SPMI_REGULATOR_SUBTYPE_LV_P150 = 0x29,
+ SPMI_REGULATOR_SUBTYPE_LV_P300 = 0x2a,
+ SPMI_REGULATOR_SUBTYPE_LV_P600 = 0x2b,
+ SPMI_REGULATOR_SUBTYPE_LV_P1200 = 0x2c,
+ SPMI_REGULATOR_SUBTYPE_LV_P450 = 0x2d,
+ SPMI_REGULATOR_SUBTYPE_LV100 = 0x01,
+ SPMI_REGULATOR_SUBTYPE_LV300 = 0x02,
+ SPMI_REGULATOR_SUBTYPE_MV300 = 0x08,
+ SPMI_REGULATOR_SUBTYPE_MV500 = 0x09,
+ SPMI_REGULATOR_SUBTYPE_HDMI = 0x10,
+ SPMI_REGULATOR_SUBTYPE_OTG = 0x11,
+ SPMI_REGULATOR_SUBTYPE_5V_BOOST = 0x01,
+ SPMI_REGULATOR_SUBTYPE_FTS_CTL = 0x08,
+ SPMI_REGULATOR_SUBTYPE_FTS2p5_CTL = 0x09,
+ SPMI_REGULATOR_SUBTYPE_BB_2A = 0x01,
+ SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL1 = 0x0d,
+ SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL2 = 0x0e,
+ SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL3 = 0x0f,
+ SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL4 = 0x10,
+};
+
+enum spmi_common_regulator_registers {
+ SPMI_COMMON_REG_DIG_MAJOR_REV = 0x01,
+ SPMI_COMMON_REG_TYPE = 0x04,
+ SPMI_COMMON_REG_SUBTYPE = 0x05,
+ SPMI_COMMON_REG_VOLTAGE_RANGE = 0x40,
+ SPMI_COMMON_REG_VOLTAGE_SET = 0x41,
+ SPMI_COMMON_REG_MODE = 0x45,
+ SPMI_COMMON_REG_ENABLE = 0x46,
+ SPMI_COMMON_REG_PULL_DOWN = 0x48,
+ SPMI_COMMON_REG_SOFT_START = 0x4c,
+ SPMI_COMMON_REG_STEP_CTRL = 0x61,
+};
+
+enum spmi_vs_registers {
+ SPMI_VS_REG_OCP = 0x4a,
+ SPMI_VS_REG_SOFT_START = 0x4c,
+};
+
+enum spmi_boost_registers {
+ SPMI_BOOST_REG_CURRENT_LIMIT = 0x4a,
+};
+
+enum spmi_boost_byp_registers {
+ SPMI_BOOST_BYP_REG_CURRENT_LIMIT = 0x4b,
+};
+
+/* Used for indexing into ctrl_reg. These are offets from 0x40 */
+enum spmi_common_control_register_index {
+ SPMI_COMMON_IDX_VOLTAGE_RANGE = 0,
+ SPMI_COMMON_IDX_VOLTAGE_SET = 1,
+ SPMI_COMMON_IDX_MODE = 5,
+ SPMI_COMMON_IDX_ENABLE = 6,
+};
+
+/* Common regulator control register layout */
+#define SPMI_COMMON_ENABLE_MASK 0x80
+#define SPMI_COMMON_ENABLE 0x80
+#define SPMI_COMMON_DISABLE 0x00
+#define SPMI_COMMON_ENABLE_FOLLOW_HW_EN3_MASK 0x08
+#define SPMI_COMMON_ENABLE_FOLLOW_HW_EN2_MASK 0x04
+#define SPMI_COMMON_ENABLE_FOLLOW_HW_EN1_MASK 0x02
+#define SPMI_COMMON_ENABLE_FOLLOW_HW_EN0_MASK 0x01
+#define SPMI_COMMON_ENABLE_FOLLOW_ALL_MASK 0x0f
+
+/* Common regulator mode register layout */
+#define SPMI_COMMON_MODE_HPM_MASK 0x80
+#define SPMI_COMMON_MODE_AUTO_MASK 0x40
+#define SPMI_COMMON_MODE_BYPASS_MASK 0x20
+#define SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK 0x10
+#define SPMI_COMMON_MODE_FOLLOW_HW_EN3_MASK 0x08
+#define SPMI_COMMON_MODE_FOLLOW_HW_EN2_MASK 0x04
+#define SPMI_COMMON_MODE_FOLLOW_HW_EN1_MASK 0x02
+#define SPMI_COMMON_MODE_FOLLOW_HW_EN0_MASK 0x01
+#define SPMI_COMMON_MODE_FOLLOW_ALL_MASK 0x1f
+
+/* Common regulator pull down control register layout */
+#define SPMI_COMMON_PULL_DOWN_ENABLE_MASK 0x80
+
+/* LDO regulator current limit control register layout */
+#define SPMI_LDO_CURRENT_LIMIT_ENABLE_MASK 0x80
+
+/* LDO regulator soft start control register layout */
+#define SPMI_LDO_SOFT_START_ENABLE_MASK 0x80
+
+/* VS regulator over current protection control register layout */
+#define SPMI_VS_OCP_OVERRIDE 0x01
+#define SPMI_VS_OCP_NO_OVERRIDE 0x00
+
+/* VS regulator soft start control register layout */
+#define SPMI_VS_SOFT_START_ENABLE_MASK 0x80
+#define SPMI_VS_SOFT_START_SEL_MASK 0x03
+
+/* Boost regulator current limit control register layout */
+#define SPMI_BOOST_CURRENT_LIMIT_ENABLE_MASK 0x80
+#define SPMI_BOOST_CURRENT_LIMIT_MASK 0x07
+
+#define SPMI_VS_OCP_DEFAULT_MAX_RETRIES 10
+#define SPMI_VS_OCP_DEFAULT_RETRY_DELAY_MS 30
+#define SPMI_VS_OCP_FALL_DELAY_US 90
+#define SPMI_VS_OCP_FAULT_DELAY_US 20000
+
+#define SPMI_FTSMPS_STEP_CTRL_STEP_MASK 0x18
+#define SPMI_FTSMPS_STEP_CTRL_STEP_SHIFT 3
+#define SPMI_FTSMPS_STEP_CTRL_DELAY_MASK 0x07
+#define SPMI_FTSMPS_STEP_CTRL_DELAY_SHIFT 0
+
+/* Clock rate in kHz of the FTSMPS regulator reference clock. */
+#define SPMI_FTSMPS_CLOCK_RATE 19200
+
+/* Minimum voltage stepper delay for each step. */
+#define SPMI_FTSMPS_STEP_DELAY 8
+
+/*
+ * The ratio SPMI_FTSMPS_STEP_MARGIN_NUM/SPMI_FTSMPS_STEP_MARGIN_DEN is used to
+ * adjust the step rate in order to account for oscillator variance.
+ */
+#define SPMI_FTSMPS_STEP_MARGIN_NUM 4
+#define SPMI_FTSMPS_STEP_MARGIN_DEN 5
+
+/*
+ * This voltage in uV is returned by get_voltage functions when there is no way
+ * to determine the current voltage level. It is needed because the regulator
+ * framework treats a 0 uV voltage as an error.
+ */
+#define VOLTAGE_UNKNOWN 1
+
+/* VSET value to decide the range of ULT SMPS */
+#define ULT_SMPS_RANGE_SPLIT 0x60
+
+/**
+ * struct spmi_voltage_range - regulator set point voltage mapping description
+ * @min_uV: Minimum programmable output voltage resulting from
+ * set point register value 0x00
+ * @max_uV: Maximum programmable output voltage
+ * @step_uV: Output voltage increase resulting from the set point
+ * register value increasing by 1
+ * @set_point_min_uV: Minimum allowed voltage
+ * @set_point_max_uV: Maximum allowed voltage. This may be tweaked in order
+ * to pick which range should be used in the case of
+ * overlapping set points.
+ * @n_voltages: Number of preferred voltage set points present in this
+ * range
+ * @range_sel: Voltage range register value corresponding to this range
+ *
+ * The following relationships must be true for the values used in this struct:
+ * (max_uV - min_uV) % step_uV == 0
+ * (set_point_min_uV - min_uV) % step_uV == 0*
+ * (set_point_max_uV - min_uV) % step_uV == 0*
+ * n_voltages = (set_point_max_uV - set_point_min_uV) / step_uV + 1
+ *
+ * *Note, set_point_min_uV == set_point_max_uV == 0 is allowed in order to
+ * specify that the voltage range has meaning, but is not preferred.
+ */
+struct spmi_voltage_range {
+ int min_uV;
+ int max_uV;
+ int step_uV;
+ int set_point_min_uV;
+ int set_point_max_uV;
+ unsigned n_voltages;
+ u8 range_sel;
+};
+
+/*
+ * The ranges specified in the spmi_voltage_set_points struct must be listed
+ * so that range[i].set_point_max_uV < range[i+1].set_point_min_uV.
+ */
+struct spmi_voltage_set_points {
+ struct spmi_voltage_range *range;
+ int count;
+ unsigned n_voltages;
+};
+
+struct spmi_regulator {
+ struct regulator_desc desc;
+ struct device *dev;
+ struct delayed_work ocp_work;
+ struct regmap *regmap;
+ struct spmi_voltage_set_points *set_points;
+ enum spmi_regulator_logical_type logical_type;
+ int ocp_irq;
+ int ocp_count;
+ int ocp_max_retries;
+ int ocp_retry_delay_ms;
+ int hpm_min_load;
+ int slew_rate;
+ ktime_t vs_enable_time;
+ u16 base;
+ struct list_head node;
+};
+
+struct spmi_regulator_mapping {
+ enum spmi_regulator_type type;
+ enum spmi_regulator_subtype subtype;
+ enum spmi_regulator_logical_type logical_type;
+ u32 revision_min;
+ u32 revision_max;
+ struct regulator_ops *ops;
+ struct spmi_voltage_set_points *set_points;
+ int hpm_min_load;
+};
+
+struct spmi_regulator_data {
+ const char *name;
+ u16 base;
+ const char *supply;
+ const char *ocp;
+ u16 force_type;
+};
+
+#define SPMI_VREG(_type, _subtype, _dig_major_min, _dig_major_max, \
+ _logical_type, _ops_val, _set_points_val, _hpm_min_load) \
+ { \
+ .type = SPMI_REGULATOR_TYPE_##_type, \
+ .subtype = SPMI_REGULATOR_SUBTYPE_##_subtype, \
+ .revision_min = _dig_major_min, \
+ .revision_max = _dig_major_max, \
+ .logical_type = SPMI_REGULATOR_LOGICAL_TYPE_##_logical_type, \
+ .ops = &spmi_##_ops_val##_ops, \
+ .set_points = &_set_points_val##_set_points, \
+ .hpm_min_load = _hpm_min_load, \
+ }
+
+#define SPMI_VREG_VS(_subtype, _dig_major_min, _dig_major_max) \
+ { \
+ .type = SPMI_REGULATOR_TYPE_VS, \
+ .subtype = SPMI_REGULATOR_SUBTYPE_##_subtype, \
+ .revision_min = _dig_major_min, \
+ .revision_max = _dig_major_max, \
+ .logical_type = SPMI_REGULATOR_LOGICAL_TYPE_VS, \
+ .ops = &spmi_vs_ops, \
+ }
+
+#define SPMI_VOLTAGE_RANGE(_range_sel, _min_uV, _set_point_min_uV, \
+ _set_point_max_uV, _max_uV, _step_uV) \
+ { \
+ .min_uV = _min_uV, \
+ .max_uV = _max_uV, \
+ .set_point_min_uV = _set_point_min_uV, \
+ .set_point_max_uV = _set_point_max_uV, \
+ .step_uV = _step_uV, \
+ .range_sel = _range_sel, \
+ }
+
+#define DEFINE_SPMI_SET_POINTS(name) \
+struct spmi_voltage_set_points name##_set_points = { \
+ .range = name##_ranges, \
+ .count = ARRAY_SIZE(name##_ranges), \
+}
+
+/*
+ * These tables contain the physically available PMIC regulator voltage setpoint
+ * ranges. Where two ranges overlap in hardware, one of the ranges is trimmed
+ * to ensure that the setpoints available to software are monotonically
+ * increasing and unique. The set_voltage callback functions expect these
+ * properties to hold.
+ */
+static struct spmi_voltage_range pldo_ranges[] = {
+ SPMI_VOLTAGE_RANGE(2, 750000, 750000, 1537500, 1537500, 12500),
+ SPMI_VOLTAGE_RANGE(3, 1500000, 1550000, 3075000, 3075000, 25000),
+ SPMI_VOLTAGE_RANGE(4, 1750000, 3100000, 4900000, 4900000, 50000),
+};
+
+static struct spmi_voltage_range nldo1_ranges[] = {
+ SPMI_VOLTAGE_RANGE(2, 750000, 750000, 1537500, 1537500, 12500),
+};
+
+static struct spmi_voltage_range nldo2_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 375000, 0, 0, 1537500, 12500),
+ SPMI_VOLTAGE_RANGE(1, 375000, 375000, 768750, 768750, 6250),
+ SPMI_VOLTAGE_RANGE(2, 750000, 775000, 1537500, 1537500, 12500),
+};
+
+static struct spmi_voltage_range nldo3_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 375000, 375000, 1537500, 1537500, 12500),
+ SPMI_VOLTAGE_RANGE(1, 375000, 0, 0, 1537500, 12500),
+ SPMI_VOLTAGE_RANGE(2, 750000, 0, 0, 1537500, 12500),
+};
+
+static struct spmi_voltage_range ln_ldo_ranges[] = {
+ SPMI_VOLTAGE_RANGE(1, 690000, 690000, 1110000, 1110000, 60000),
+ SPMI_VOLTAGE_RANGE(0, 1380000, 1380000, 2220000, 2220000, 120000),
+};
+
+static struct spmi_voltage_range smps_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 375000, 375000, 1562500, 1562500, 12500),
+ SPMI_VOLTAGE_RANGE(1, 1550000, 1575000, 3125000, 3125000, 25000),
+};
+
+static struct spmi_voltage_range ftsmps_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 0, 350000, 1275000, 1275000, 5000),
+ SPMI_VOLTAGE_RANGE(1, 0, 1280000, 2040000, 2040000, 10000),
+};
+
+static struct spmi_voltage_range ftsmps2p5_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 80000, 350000, 1355000, 1355000, 5000),
+ SPMI_VOLTAGE_RANGE(1, 160000, 1360000, 2200000, 2200000, 10000),
+};
+
+static struct spmi_voltage_range boost_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 4000000, 4000000, 5550000, 5550000, 50000),
+};
+
+static struct spmi_voltage_range boost_byp_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 2500000, 2500000, 5200000, 5650000, 50000),
+};
+
+static struct spmi_voltage_range ult_lo_smps_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 375000, 375000, 1562500, 1562500, 12500),
+ SPMI_VOLTAGE_RANGE(1, 750000, 0, 0, 1525000, 25000),
+};
+
+static struct spmi_voltage_range ult_ho_smps_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 1550000, 1550000, 2325000, 2325000, 25000),
+};
+
+static struct spmi_voltage_range ult_nldo_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 375000, 375000, 1537500, 1537500, 12500),
+};
+
+static struct spmi_voltage_range ult_pldo_ranges[] = {
+ SPMI_VOLTAGE_RANGE(0, 1750000, 1750000, 3337500, 3337500, 12500),
+};
+
+static DEFINE_SPMI_SET_POINTS(pldo);
+static DEFINE_SPMI_SET_POINTS(nldo1);
+static DEFINE_SPMI_SET_POINTS(nldo2);
+static DEFINE_SPMI_SET_POINTS(nldo3);
+static DEFINE_SPMI_SET_POINTS(ln_ldo);
+static DEFINE_SPMI_SET_POINTS(smps);
+static DEFINE_SPMI_SET_POINTS(ftsmps);
+static DEFINE_SPMI_SET_POINTS(ftsmps2p5);
+static DEFINE_SPMI_SET_POINTS(boost);
+static DEFINE_SPMI_SET_POINTS(boost_byp);
+static DEFINE_SPMI_SET_POINTS(ult_lo_smps);
+static DEFINE_SPMI_SET_POINTS(ult_ho_smps);
+static DEFINE_SPMI_SET_POINTS(ult_nldo);
+static DEFINE_SPMI_SET_POINTS(ult_pldo);
+
+static inline int spmi_vreg_read(struct spmi_regulator *vreg, u16 addr, u8 *buf,
+ int len)
+{
+ return regmap_bulk_read(vreg->regmap, vreg->base + addr, buf, len);
+}
+
+static inline int spmi_vreg_write(struct spmi_regulator *vreg, u16 addr,
+ u8 *buf, int len)
+{
+ return regmap_bulk_write(vreg->regmap, vreg->base + addr, buf, len);
+}
+
+static int spmi_vreg_update_bits(struct spmi_regulator *vreg, u16 addr, u8 val,
+ u8 mask)
+{
+ return regmap_update_bits(vreg->regmap, vreg->base + addr, mask, val);
+}
+
+static int spmi_regulator_common_is_enabled(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ u8 reg;
+
+ spmi_vreg_read(vreg, SPMI_COMMON_REG_ENABLE, ®, 1);
+
+ return (reg & SPMI_COMMON_ENABLE_MASK) == SPMI_COMMON_ENABLE;
+}
+
+static int spmi_regulator_common_enable(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+
+ return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_ENABLE,
+ SPMI_COMMON_ENABLE, SPMI_COMMON_ENABLE_MASK);
+}
+
+static int spmi_regulator_vs_enable(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+
+ if (vreg->ocp_irq) {
+ vreg->ocp_count = 0;
+ vreg->vs_enable_time = ktime_get();
+ }
+
+ return spmi_regulator_common_enable(rdev);
+}
+
+static int spmi_regulator_common_disable(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+
+ return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_ENABLE,
+ SPMI_COMMON_DISABLE, SPMI_COMMON_ENABLE_MASK);
+}
+
+static int spmi_regulator_select_voltage(struct spmi_regulator *vreg,
+ int min_uV, int max_uV, u8 *range_sel, u8 *voltage_sel,
+ unsigned *selector)
+{
+ const struct spmi_voltage_range *range;
+ int uV = min_uV;
+ int lim_min_uV, lim_max_uV, i, range_id, range_max_uV;
+
+ /* Check if request voltage is outside of physically settable range. */
+ lim_min_uV = vreg->set_points->range[0].set_point_min_uV;
+ lim_max_uV =
+ vreg->set_points->range[vreg->set_points->count - 1].set_point_max_uV;
+
+ if (uV < lim_min_uV && max_uV >= lim_min_uV)
+ uV = lim_min_uV;
+
+ if (uV < lim_min_uV || uV > lim_max_uV) {
+ dev_err(vreg->dev,
+ "request v=[%d, %d] is outside possible v=[%d, %d]\n",
+ min_uV, max_uV, lim_min_uV, lim_max_uV);
+ return -EINVAL;
+ }
+
+ /* Find the range which uV is inside of. */
+ for (i = vreg->set_points->count - 1; i > 0; i--) {
+ range_max_uV = vreg->set_points->range[i - 1].set_point_max_uV;
+ if (uV > range_max_uV && range_max_uV > 0)
+ break;
+ }
+
+ range_id = i;
+ range = &vreg->set_points->range[range_id];
+ *range_sel = range->range_sel;
+
+ /*
+ * Force uV to be an allowed set point by applying a ceiling function to
+ * the uV value.
+ */
+ *voltage_sel = (uV - range->min_uV + range->step_uV - 1)
+ / range->step_uV;
+ uV = *voltage_sel * range->step_uV + range->min_uV;
+
+ if (uV > max_uV) {
+ dev_err(vreg->dev,
+ "request v=[%d, %d] cannot be met by any set point; "
+ "next set point: %d\n",
+ min_uV, max_uV, uV);
+ return -EINVAL;
+ }
+
+ *selector = 0;
+ for (i = 0; i < range_id; i++)
+ *selector += vreg->set_points->range[i].n_voltages;
+ *selector += (uV - range->set_point_min_uV) / range->step_uV;
+
+ return 0;
+}
+
+static const struct spmi_voltage_range *
+spmi_regulator_find_range(struct spmi_regulator *vreg)
+{
+ u8 range_sel;
+ const struct spmi_voltage_range *range, *end;
+
+ range = vreg->set_points->range;
+ end = range + vreg->set_points->count;
+
+ spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, &range_sel, 1);
+
+ for (; range < end; range++)
+ if (range->range_sel == range_sel)
+ return range;
+
+ return NULL;
+}
+
+static int spmi_regulator_select_voltage_same_range(struct spmi_regulator *vreg,
+ int min_uV, int max_uV, u8 *range_sel, u8 *voltage_sel,
+ unsigned *selector)
+{
+ const struct spmi_voltage_range *range;
+ int uV = min_uV;
+ int i;
+
+ range = spmi_regulator_find_range(vreg);
+ if (!range)
+ goto different_range;
+
+ if (uV < range->min_uV && max_uV >= range->min_uV)
+ uV = range->min_uV;
+
+ if (uV < range->min_uV || uV > range->max_uV) {
+ /* Current range doesn't support the requested voltage. */
+ goto different_range;
+ }
+
+ /*
+ * Force uV to be an allowed set point by applying a ceiling function to
+ * the uV value.
+ */
+ *voltage_sel = DIV_ROUND_UP(uV - range->min_uV, range->step_uV);
+ uV = *voltage_sel * range->step_uV + range->min_uV;
+
+ if (uV > max_uV) {
+ /*
+ * No set point in the current voltage range is within the
+ * requested min_uV to max_uV range.
+ */
+ goto different_range;
+ }
+
+ *selector = 0;
+ for (i = 0; i < vreg->set_points->count; i++) {
+ if (uV >= vreg->set_points->range[i].set_point_min_uV
+ && uV <= vreg->set_points->range[i].set_point_max_uV)
+ *selector +=
+ (uV - vreg->set_points->range[i].set_point_min_uV)
+ / vreg->set_points->range[i].step_uV;
+ break;
+
+ *selector += vreg->set_points->range[i].n_voltages;
+ }
+
+ if (*selector >= vreg->set_points->n_voltages)
+ goto different_range;
+
+ return 0;
+
+different_range:
+ return spmi_regulator_select_voltage(vreg, min_uV, max_uV,
+ range_sel, voltage_sel, selector);
+}
+
+static int spmi_regulator_common_set_voltage(struct regulator_dev *rdev,
+ int min_uV, int max_uV, unsigned *selector)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ int ret;
+ u8 buf[2];
+ u8 range_sel, voltage_sel;
+
+ /*
+ * Favor staying in the current voltage range if possible. This avoids
+ * voltage spikes that occur when changing the voltage range.
+ */
+ ret = spmi_regulator_select_voltage_same_range(vreg, min_uV, max_uV,
+ &range_sel, &voltage_sel, selector);
+ if (ret)
+ return ret;
+
+ buf[0] = range_sel;
+ buf[1] = voltage_sel;
+ return spmi_vreg_write(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, buf, 2);
+}
+
+static int spmi_regulator_set_voltage_time_sel(struct regulator_dev *rdev,
+ unsigned int old_selector, unsigned int new_selector)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ const struct spmi_voltage_range *range;
+ int diff_uV;
+
+ range = spmi_regulator_find_range(vreg);
+ if (!range)
+ return -EINVAL;
+
+ diff_uV = abs(new_selector - old_selector) * range->step_uV;
+
+ return DIV_ROUND_UP(diff_uV, vreg->slew_rate);
+}
+
+static int spmi_regulator_common_get_voltage(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ const struct spmi_voltage_range *range;
+ u8 voltage_sel;
+
+ spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_SET, &voltage_sel, 1);
+
+ range = spmi_regulator_find_range(vreg);
+ if (!range)
+ return VOLTAGE_UNKNOWN;
+
+ return range->step_uV * voltage_sel + range->min_uV;
+}
+
+static int spmi_regulator_single_range_set_voltage(struct regulator_dev *rdev,
+ int min_uV, int max_uV, unsigned *selector)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ int ret;
+ u8 range_sel, sel;
+
+ ret = spmi_regulator_select_voltage(vreg, min_uV, max_uV, &range_sel,
+ &sel, selector);
+ if (ret) {
+ dev_err(vreg->dev, "could not set voltage, ret=%d\n", ret);
+ return ret;
+ }
+
+ /*
+ * Certain types of regulators do not have a range select register so
+ * only voltage set register needs to be written.
+ */
+ return spmi_vreg_write(vreg, SPMI_COMMON_REG_VOLTAGE_SET, &sel, 1);
+}
+
+static int spmi_regulator_single_range_get_voltage(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ const struct spmi_voltage_range *range = vreg->set_points->range;
+ u8 voltage_sel;
+
+ spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_SET, &voltage_sel, 1);
+
+ return range->step_uV * voltage_sel + range->min_uV;
+}
+
+static int spmi_regulator_ult_lo_smps_set_voltage(struct regulator_dev *rdev,
+ int min_uV, int max_uV, unsigned *selector)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ int ret;
+ u8 range_sel, voltage_sel;
+
+ /*
+ * Favor staying in the current voltage range if possible. This avoids
+ * voltage spikes that occur when changing the voltage range.
+ */
+ ret = spmi_regulator_select_voltage_same_range(vreg, min_uV, max_uV,
+ &range_sel, &voltage_sel, selector);
+ if (ret)
+ return ret;
+
+ /*
+ * Calculate VSET based on range
+ * In case of range 0: voltage_sel is a 7 bit value, can be written
+ * witout any modification.
+ * In case of range 1: voltage_sel is a 5 bit value, bits[7-5] set to
+ * [011].
+ */
+ if (range_sel == 1)
+ voltage_sel |= ULT_SMPS_RANGE_SPLIT;
+
+ ret = spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_VOLTAGE_SET,
+ voltage_sel, 0xff);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int spmi_regulator_ult_lo_smps_get_voltage(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ const struct spmi_voltage_range *range;
+ u8 voltage_sel;
+
+ spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_SET, &voltage_sel, 1);
+
+ range = spmi_regulator_find_range(vreg);
+ if (!range)
+ return VOLTAGE_UNKNOWN;
+
+ if (range->range_sel == 1)
+ voltage_sel &= ~ULT_SMPS_RANGE_SPLIT;
+
+ return range->step_uV * voltage_sel + range->min_uV;
+}
+
+static int spmi_regulator_common_list_voltage(struct regulator_dev *rdev,
+ unsigned selector)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ int uV = 0;
+ int i;
+
+ if (selector >= vreg->set_points->n_voltages)
+ return 0;
+
+ for (i = 0; i < vreg->set_points->count; i++) {
+ if (selector < vreg->set_points->range[i].n_voltages)
+ uV = selector * vreg->set_points->range[i].step_uV
+ + vreg->set_points->range[i].set_point_min_uV;
+ break;
+
+ selector -= vreg->set_points->range[i].n_voltages;
+ }
+
+ return uV;
+}
+
+static int
+spmi_regulator_common_set_bypass(struct regulator_dev *rdev, bool enable)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ u8 mask = SPMI_COMMON_MODE_BYPASS_MASK;
+ u8 val = 0;
+
+ if (enable)
+ val = mask;
+
+ return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask);
+}
+
+static int
+spmi_regulator_common_get_bypass(struct regulator_dev *rdev, bool *enable)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ u8 val;
+ int ret;
+
+ ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_MODE, &val, 1);
+ *enable = val & SPMI_COMMON_MODE_BYPASS_MASK;
+
+ return ret;
+}
+
+static unsigned int spmi_regulator_common_get_mode(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ u8 reg;
+
+ spmi_vreg_read(vreg, SPMI_COMMON_REG_MODE, ®, 1);
+
+ if (reg & SPMI_COMMON_MODE_HPM_MASK)
+ return REGULATOR_MODE_NORMAL;
+
+ return REGULATOR_MODE_IDLE;
+}
+
+static int
+spmi_regulator_common_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ u8 mask = SPMI_COMMON_MODE_HPM_MASK;
+ u8 val = 0;
+
+ if (mode == REGULATOR_MODE_NORMAL)
+ val = mask;
+
+ return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask);
+}
+
+static int
+spmi_regulator_common_set_load(struct regulator_dev *rdev, int load_uA)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ unsigned int mode;
+
+ if (load_uA >= vreg->hpm_min_load)
+ mode = REGULATOR_MODE_NORMAL;
+ else
+ mode = REGULATOR_MODE_IDLE;
+
+ return spmi_regulator_common_set_mode(rdev, mode);
+}
+
+static int spmi_regulator_vs_clear_ocp(struct spmi_regulator *vreg)
+{
+ int ret;
+
+ ret = spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_ENABLE,
+ SPMI_COMMON_DISABLE, SPMI_COMMON_ENABLE_MASK);
+
+ vreg->vs_enable_time = ktime_get();
+
+ ret = spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_ENABLE,
+ SPMI_COMMON_ENABLE, SPMI_COMMON_ENABLE_MASK);
+
+ return ret;
+}
+
+static void spmi_regulator_vs_ocp_work(struct work_struct *work)
+{
+ struct delayed_work *dwork = to_delayed_work(work);
+ struct spmi_regulator *vreg
+ = container_of(dwork, struct spmi_regulator, ocp_work);
+
+ spmi_regulator_vs_clear_ocp(vreg);
+}
+
+static irqreturn_t spmi_regulator_vs_ocp_isr(int irq, void *data)
+{
+ struct spmi_regulator *vreg = data;
+ ktime_t ocp_irq_time;
+ s64 ocp_trigger_delay_us;
+
+ ocp_irq_time = ktime_get();
+ ocp_trigger_delay_us = ktime_us_delta(ocp_irq_time,
+ vreg->vs_enable_time);
+
+ /*
+ * Reset the OCP count if there is a large delay between switch enable
+ * and when OCP triggers. This is indicative of a hotplug event as
+ * opposed to a fault.
+ */
+ if (ocp_trigger_delay_us > SPMI_VS_OCP_FAULT_DELAY_US)
+ vreg->ocp_count = 0;
+
+ /* Wait for switch output to settle back to 0 V after OCP triggered. */
+ udelay(SPMI_VS_OCP_FALL_DELAY_US);
+
+ vreg->ocp_count++;
+
+ if (vreg->ocp_count == 1) {
+ /* Immediately clear the over current condition. */
+ spmi_regulator_vs_clear_ocp(vreg);
+ } else if (vreg->ocp_count <= vreg->ocp_max_retries) {
+ /* Schedule the over current clear task to run later. */
+ schedule_delayed_work(&vreg->ocp_work,
+ msecs_to_jiffies(vreg->ocp_retry_delay_ms) + 1);
+ } else {
+ dev_err(vreg->dev,
+ "OCP triggered %d times; no further retries\n",
+ vreg->ocp_count);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static struct regulator_ops spmi_smps_ops = {
+ .enable = spmi_regulator_common_enable,
+ .disable = spmi_regulator_common_disable,
+ .is_enabled = spmi_regulator_common_is_enabled,
+ .set_voltage = spmi_regulator_common_set_voltage,
+ .get_voltage = spmi_regulator_common_get_voltage,
+ .list_voltage = spmi_regulator_common_list_voltage,
+ .set_mode = spmi_regulator_common_set_mode,
+ .get_mode = spmi_regulator_common_get_mode,
+ .set_load = spmi_regulator_common_set_load,
+};
+
+static struct regulator_ops spmi_ldo_ops = {
+ .enable = spmi_regulator_common_enable,
+ .disable = spmi_regulator_common_disable,
+ .is_enabled = spmi_regulator_common_is_enabled,
+ .set_voltage = spmi_regulator_common_set_voltage,
+ .get_voltage = spmi_regulator_common_get_voltage,
+ .list_voltage = spmi_regulator_common_list_voltage,
+ .set_mode = spmi_regulator_common_set_mode,
+ .get_mode = spmi_regulator_common_get_mode,
+ .set_load = spmi_regulator_common_set_load,
+ .set_bypass = spmi_regulator_common_set_bypass,
+ .get_bypass = spmi_regulator_common_get_bypass,
+};
+
+static struct regulator_ops spmi_ln_ldo_ops = {
+ .enable = spmi_regulator_common_enable,
+ .disable = spmi_regulator_common_disable,
+ .is_enabled = spmi_regulator_common_is_enabled,
+ .set_voltage = spmi_regulator_common_set_voltage,
+ .get_voltage = spmi_regulator_common_get_voltage,
+ .list_voltage = spmi_regulator_common_list_voltage,
+ .set_bypass = spmi_regulator_common_set_bypass,
+ .get_bypass = spmi_regulator_common_get_bypass,
+};
+
+static struct regulator_ops spmi_vs_ops = {
+ .enable = spmi_regulator_vs_enable,
+ .disable = spmi_regulator_common_disable,
+ .is_enabled = spmi_regulator_common_is_enabled,
+};
+
+static struct regulator_ops spmi_boost_ops = {
+ .enable = spmi_regulator_common_enable,
+ .disable = spmi_regulator_common_disable,
+ .is_enabled = spmi_regulator_common_is_enabled,
+ .set_voltage = spmi_regulator_single_range_set_voltage,
+ .get_voltage = spmi_regulator_single_range_get_voltage,
+ .list_voltage = spmi_regulator_common_list_voltage,
+};
+
+static struct regulator_ops spmi_ftsmps_ops = {
+ .enable = spmi_regulator_common_enable,
+ .disable = spmi_regulator_common_disable,
+ .is_enabled = spmi_regulator_common_is_enabled,
+ .set_voltage = spmi_regulator_common_set_voltage,
+ .set_voltage_time_sel = spmi_regulator_set_voltage_time_sel,
+ .get_voltage = spmi_regulator_common_get_voltage,
+ .list_voltage = spmi_regulator_common_list_voltage,
+ .set_mode = spmi_regulator_common_set_mode,
+ .get_mode = spmi_regulator_common_get_mode,
+ .set_load = spmi_regulator_common_set_load,
+};
+
+static struct regulator_ops spmi_ult_lo_smps_ops = {
+ .enable = spmi_regulator_common_enable,
+ .disable = spmi_regulator_common_disable,
+ .is_enabled = spmi_regulator_common_is_enabled,
+ .set_voltage = spmi_regulator_ult_lo_smps_set_voltage,
+ .get_voltage = spmi_regulator_ult_lo_smps_get_voltage,
+ .list_voltage = spmi_regulator_common_list_voltage,
+ .set_mode = spmi_regulator_common_set_mode,
+ .get_mode = spmi_regulator_common_get_mode,
+ .set_load = spmi_regulator_common_set_load,
+};
+
+static struct regulator_ops spmi_ult_ho_smps_ops = {
+ .enable = spmi_regulator_common_enable,
+ .disable = spmi_regulator_common_disable,
+ .is_enabled = spmi_regulator_common_is_enabled,
+ .set_voltage = spmi_regulator_single_range_set_voltage,
+ .get_voltage = spmi_regulator_single_range_get_voltage,
+ .list_voltage = spmi_regulator_common_list_voltage,
+ .set_mode = spmi_regulator_common_set_mode,
+ .get_mode = spmi_regulator_common_get_mode,
+ .set_load = spmi_regulator_common_set_load,
+};
+
+static struct regulator_ops spmi_ult_ldo_ops = {
+ .enable = spmi_regulator_common_enable,
+ .disable = spmi_regulator_common_disable,
+ .is_enabled = spmi_regulator_common_is_enabled,
+ .set_voltage = spmi_regulator_single_range_set_voltage,
+ .get_voltage = spmi_regulator_single_range_get_voltage,
+ .list_voltage = spmi_regulator_common_list_voltage,
+ .set_mode = spmi_regulator_common_set_mode,
+ .get_mode = spmi_regulator_common_get_mode,
+ .set_load = spmi_regulator_common_set_load,
+ .set_bypass = spmi_regulator_common_set_bypass,
+ .get_bypass = spmi_regulator_common_get_bypass,
+};
+
+/* Maximum possible digital major revision value */
+#define INF 0xFF
+
+static const struct spmi_regulator_mapping supported_regulators[] = {
+ /* type subtype dig_min dig_max ltype ops setpoints hpm_min */
+ SPMI_VREG(BUCK, GP_CTL, 0, INF, SMPS, smps, smps, 100000),
+ SPMI_VREG(LDO, N300, 0, INF, LDO, ldo, nldo1, 10000),
+ SPMI_VREG(LDO, N600, 0, 0, LDO, ldo, nldo2, 10000),
+ SPMI_VREG(LDO, N1200, 0, 0, LDO, ldo, nldo2, 10000),
+ SPMI_VREG(LDO, N600, 1, INF, LDO, ldo, nldo3, 10000),
+ SPMI_VREG(LDO, N1200, 1, INF, LDO, ldo, nldo3, 10000),
+ SPMI_VREG(LDO, N600_ST, 0, 0, LDO, ldo, nldo2, 10000),
+ SPMI_VREG(LDO, N1200_ST, 0, 0, LDO, ldo, nldo2, 10000),
+ SPMI_VREG(LDO, N600_ST, 1, INF, LDO, ldo, nldo3, 10000),
+ SPMI_VREG(LDO, N1200_ST, 1, INF, LDO, ldo, nldo3, 10000),
+ SPMI_VREG(LDO, P50, 0, INF, LDO, ldo, pldo, 5000),
+ SPMI_VREG(LDO, P150, 0, INF, LDO, ldo, pldo, 10000),
+ SPMI_VREG(LDO, P300, 0, INF, LDO, ldo, pldo, 10000),
+ SPMI_VREG(LDO, P600, 0, INF, LDO, ldo, pldo, 10000),
+ SPMI_VREG(LDO, P1200, 0, INF, LDO, ldo, pldo, 10000),
+ SPMI_VREG(LDO, LN, 0, INF, LN_LDO, ln_ldo, ln_ldo, 0),
+ SPMI_VREG(LDO, LV_P50, 0, INF, LDO, ldo, pldo, 5000),
+ SPMI_VREG(LDO, LV_P150, 0, INF, LDO, ldo, pldo, 10000),
+ SPMI_VREG(LDO, LV_P300, 0, INF, LDO, ldo, pldo, 10000),
+ SPMI_VREG(LDO, LV_P600, 0, INF, LDO, ldo, pldo, 10000),
+ SPMI_VREG(LDO, LV_P1200, 0, INF, LDO, ldo, pldo, 10000),
+ SPMI_VREG_VS(LV100, 0, INF),
+ SPMI_VREG_VS(LV300, 0, INF),
+ SPMI_VREG_VS(MV300, 0, INF),
+ SPMI_VREG_VS(MV500, 0, INF),
+ SPMI_VREG_VS(HDMI, 0, INF),
+ SPMI_VREG_VS(OTG, 0, INF),
+ SPMI_VREG(BOOST, 5V_BOOST, 0, INF, BOOST, boost, boost, 0),
+ SPMI_VREG(FTS, FTS_CTL, 0, INF, FTSMPS, ftsmps, ftsmps, 100000),
+ SPMI_VREG(FTS, FTS2p5_CTL, 0, INF, FTSMPS, ftsmps, ftsmps2p5, 100000),
+ SPMI_VREG(BOOST_BYP, BB_2A, 0, INF, BOOST_BYP, boost, boost_byp, 0),
+ SPMI_VREG(ULT_BUCK, ULT_HF_CTL1, 0, INF, ULT_LO_SMPS, ult_lo_smps,
+ ult_lo_smps, 100000),
+ SPMI_VREG(ULT_BUCK, ULT_HF_CTL2, 0, INF, ULT_LO_SMPS, ult_lo_smps,
+ ult_lo_smps, 100000),
+ SPMI_VREG(ULT_BUCK, ULT_HF_CTL3, 0, INF, ULT_LO_SMPS, ult_lo_smps,
+ ult_lo_smps, 100000),
+ SPMI_VREG(ULT_BUCK, ULT_HF_CTL4, 0, INF, ULT_HO_SMPS, ult_ho_smps,
+ ult_ho_smps, 100000),
+ SPMI_VREG(ULT_LDO, N300_ST, 0, INF, ULT_LDO, ult_ldo, ult_nldo, 10000),
+ SPMI_VREG(ULT_LDO, N600_ST, 0, INF, ULT_LDO, ult_ldo, ult_nldo, 10000),
+ SPMI_VREG(ULT_LDO, N900_ST, 0, INF, ULT_LDO, ult_ldo, ult_nldo, 10000),
+ SPMI_VREG(ULT_LDO, N1200_ST, 0, INF, ULT_LDO, ult_ldo, ult_nldo, 10000),
+ SPMI_VREG(ULT_LDO, LV_P150, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000),
+ SPMI_VREG(ULT_LDO, LV_P300, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000),
+ SPMI_VREG(ULT_LDO, LV_P450, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000),
+ SPMI_VREG(ULT_LDO, P600, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000),
+ SPMI_VREG(ULT_LDO, P150, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000),
+ SPMI_VREG(ULT_LDO, P50, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 5000),
+};
+
+static void spmi_calculate_num_voltages(struct spmi_voltage_set_points *points)
+{
+ unsigned int n;
+ struct spmi_voltage_range *range = points->range;
+
+ for (; range < points->range + points->count; range++) {
+ n = 0;
+ if (range->set_point_max_uV) {
+ n = range->set_point_max_uV - range->set_point_min_uV;
+ n /= range->step_uV + 1;
+ }
+ range->n_voltages = n;
+ points->n_voltages += n;
+ }
+}
+
+static int spmi_regulator_match(struct spmi_regulator *vreg, u16 force_type)
+{
+ const struct spmi_regulator_mapping *mapping;
+ int ret, i;
+ u32 dig_major_rev;
+ u8 version[SPMI_COMMON_REG_SUBTYPE - SPMI_COMMON_REG_DIG_MAJOR_REV + 1];
+ u8 type, subtype;
+
+ ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_DIG_MAJOR_REV, version,
+ ARRAY_SIZE(version));
+ if (ret) {
+ dev_err(vreg->dev, "could not read version registers\n");
+ return ret;
+ }
+ dig_major_rev = version[SPMI_COMMON_REG_DIG_MAJOR_REV
+ - SPMI_COMMON_REG_DIG_MAJOR_REV];
+ if (!force_type) {
+ type = version[SPMI_COMMON_REG_TYPE -
+ SPMI_COMMON_REG_DIG_MAJOR_REV];
+ subtype = version[SPMI_COMMON_REG_SUBTYPE -
+ SPMI_COMMON_REG_DIG_MAJOR_REV];
+ } else {
+ type = force_type >> 8;
+ subtype = force_type;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(supported_regulators); i++) {
+ mapping = &supported_regulators[i];
+ if (mapping->type == type && mapping->subtype == subtype
+ && mapping->revision_min <= dig_major_rev
+ && mapping->revision_max >= dig_major_rev)
+ goto found;
+ }
+
+ dev_err(vreg->dev,
+ "unsupported regulator: name=%s type=0x%02X, subtype=0x%02X, dig major rev=0x%02X\n",
+ vreg->desc.name, type, subtype, dig_major_rev);
+
+ return -ENODEV;
+
+found:
+ vreg->logical_type = mapping->logical_type;
+ vreg->set_points = mapping->set_points;
+ vreg->hpm_min_load = mapping->hpm_min_load;
+ vreg->desc.ops = mapping->ops;
+
+ if (mapping->set_points) {
+ if (!mapping->set_points->n_voltages)
+ spmi_calculate_num_voltages(mapping->set_points);
+ vreg->desc.n_voltages = mapping->set_points->n_voltages;
+ }
+
+ return 0;
+}
+
+static int spmi_regulator_ftsmps_init_slew_rate(struct spmi_regulator *vreg)
+{
+ int ret;
+ u8 reg = 0;
+ int step, delay, slew_rate;
+ const struct spmi_voltage_range *range;
+
+ ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_STEP_CTRL, ®, 1);
+ if (ret) {
+ dev_err(vreg->dev, "spmi read failed, ret=%d\n", ret);
+ return ret;
+ }
+
+ range = spmi_regulator_find_range(vreg);
+ if (!range)
+ return -EINVAL;
+
+ step = reg & SPMI_FTSMPS_STEP_CTRL_STEP_MASK;
+ step >>= SPMI_FTSMPS_STEP_CTRL_STEP_SHIFT;
+
+ delay = reg & SPMI_FTSMPS_STEP_CTRL_DELAY_MASK;
+ delay >>= SPMI_FTSMPS_STEP_CTRL_DELAY_SHIFT;
+
+ /* slew_rate has units of uV/us */
+ slew_rate = SPMI_FTSMPS_CLOCK_RATE * range->step_uV * (1 << step);
+ slew_rate /= 1000 * (SPMI_FTSMPS_STEP_DELAY << delay);
+ slew_rate *= SPMI_FTSMPS_STEP_MARGIN_NUM;
+ slew_rate /= SPMI_FTSMPS_STEP_MARGIN_DEN;
+
+ /* Ensure that the slew rate is greater than 0 */
+ vreg->slew_rate = max(slew_rate, 1);
+
+ return ret;
+}
+
+static unsigned int spmi_regulator_of_map_mode(unsigned int mode)
+{
+ if (mode)
+ return REGULATOR_MODE_NORMAL;
+
+ return REGULATOR_MODE_IDLE;
+}
+
+static int spmi_regulator_of_parse(struct device_node *node,
+ const struct regulator_desc *desc,
+ struct regulator_config *config)
+{
+ struct spmi_regulator *vreg = config->driver_data;
+ struct device *dev = config->dev;
+ int ret;
+
+ vreg->ocp_max_retries = SPMI_VS_OCP_DEFAULT_MAX_RETRIES;
+ vreg->ocp_retry_delay_ms = SPMI_VS_OCP_DEFAULT_RETRY_DELAY_MS;
+
+ if (vreg->logical_type == SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS) {
+ ret = spmi_regulator_ftsmps_init_slew_rate(vreg);
+ if (ret)
+ return ret;
+ }
+
+ if (vreg->logical_type != SPMI_REGULATOR_LOGICAL_TYPE_VS)
+ vreg->ocp_irq = 0;
+
+ if (vreg->ocp_irq) {
+ ret = devm_request_irq(dev, vreg->ocp_irq,
+ spmi_regulator_vs_ocp_isr, IRQF_TRIGGER_RISING, "ocp",
+ vreg);
+ if (ret < 0) {
+ dev_err(dev, "failed to request irq %d, ret=%d\n",
+ vreg->ocp_irq, ret);
+ return ret;
+ }
+
+ INIT_DELAYED_WORK(&vreg->ocp_work, spmi_regulator_vs_ocp_work);
+ }
+
+ return 0;
+}
+
+static const struct spmi_regulator_data pm8941_regulators[] = {
+ { "s1", 0x1400, "vdd_s1", },
+ { "s2", 0x1700, "vdd_s2", },
+ { "s3", 0x1a00, "vdd_s3", },
+ { "l1", 0x4000, "vdd_l1_l3", },
+ { "l2", 0x4100, "vdd_l2_lvs_1_2_3", },
+ { "l3", 0x4200, "vdd_l1_l3", },
+ { "l4", 0x4300, "vdd_l4_l11", },
+ { "l5", 0x4400, "vdd_l5_l7", NULL, 0x0410 },
+ { "l6", 0x4500, "vdd_l6_l12_l14_l15", },
+ { "l7", 0x4600, "vdd_l5_l7", NULL, 0x0410 },
+ { "l8", 0x4700, "vdd_l8_l16_l18_19", },
+ { "l9", 0x4800, "vdd_l9_l10_l17_l22", },
+ { "l10", 0x4900, "vdd_l9_l10_l17_l22", },
+ { "l11", 0x4a00, "vdd_l4_l11", },
+ { "l12", 0x4b00, "vdd_l6_l12_l14_l15", },
+ { "l13", 0x4c00, "vdd_l13_l20_l23_l24", },
+ { "l14", 0x4d00, "vdd_l6_l12_l14_l15", },
+ { "l15", 0x4e00, "vdd_l6_l12_l14_l15", },
+ { "l16", 0x4f00, "vdd_l8_l16_l18_19", },
+ { "l17", 0x5000, "vdd_l9_l10_l17_l22", },
+ { "l18", 0x5100, "vdd_l8_l16_l18_19", },
+ { "l19", 0x5200, "vdd_l8_l16_l18_19", },
+ { "l20", 0x5300, "vdd_l13_l20_l23_l24", },
+ { "l21", 0x5400, "vdd_l21", },
+ { "l22", 0x5500, "vdd_l9_l10_l17_l22", },
+ { "l23", 0x5600, "vdd_l13_l20_l23_l24", },
+ { "l24", 0x5700, "vdd_l13_l20_l23_l24", },
+ { "lvs1", 0x8000, "vdd_l2_lvs_1_2_3", },
+ { "lvs2", 0x8100, "vdd_l2_lvs_1_2_3", },
+ { "lvs3", 0x8200, "vdd_l2_lvs_1_2_3", },
+ { "mvs1", 0x8300, "vin_5vs", },
+ { "mvs2", 0x8400, "vin_5vs", },
+ { }
+};
+
+static const struct spmi_regulator_data pm8841_regulators[] = {
+ { "s1", 0x1400, "vdd_s1", },
+ { "s2", 0x1700, "vdd_s2", NULL, 0x1c08 },
+ { "s3", 0x1a00, "vdd_s3", },
+ { "s4", 0x1d00, "vdd_s4", NULL, 0x1c08 },
+ { "s5", 0x2000, "vdd_s5", NULL, 0x1c08 },
+ { "s6", 0x2300, "vdd_s6", NULL, 0x1c08 },
+ { "s7", 0x2600, "vdd_s7", NULL, 0x1c08 },
+ { "s8", 0x2900, "vdd_s8", NULL, 0x1c08 },
+ { }
+};
+
+static const struct spmi_regulator_data pm8916_regulators[] = {
+ { "s1", 0x1400, "vdd_s1", },
+ { "s2", 0x1700, "vdd_s2", },
+ { "s3", 0x1a00, "vdd_s3", },
+ { "s4", 0x1d00, "vdd_s4", },
+ { "l1", 0x4000, "vdd_l1_l3", },
+ { "l2", 0x4100, "vdd_l2", },
+ { "l3", 0x4200, "vdd_l1_l3", },
+ { "l4", 0x4300, "vdd_l4_l5_l6", },
+ { "l5", 0x4400, "vdd_l4_l5_l6", },
+ { "l6", 0x4500, "vdd_l4_l5_l6", },
+ { "l7", 0x4600, "vdd_l7", },
+ { "l8", 0x4700, "vdd_l8_l11_l14_l15_l16", },
+ { "l9", 0x4800, "vdd_l9_l10_l12_l13_l17_l18", },
+ { "l10", 0x4900, "vdd_l9_l10_l12_l13_l17_l18", },
+ { "l11", 0x4a00, "vdd_l8_l11_l14_l15_l16", },
+ { "l12", 0x4b00, "vdd_l9_l10_l12_l13_l17_l18", },
+ { "l13", 0x4c00, "vdd_l9_l10_l12_l13_l17_l18", },
+ { "l14", 0x4d00, "vdd_l8_l11_l14_l15_l16", },
+ { "l15", 0x4e00, "vdd_l8_l11_l14_l15_l16", },
+ { "l16", 0x4f00, "vdd_l8_l11_l14_l15_l16", },
+ { "l17", 0x5000, "vdd_l9_l10_l12_l13_l17_l18", },
+ { "l18", 0x5100, "vdd_l9_l10_l12_l13_l17_l18", },
+ { }
+};
+
+static const struct of_device_id qcom_spmi_regulator_match[] = {
+ { .compatible = "qcom,pm8841-regulators", .data = &pm8841_regulators },
+ { .compatible = "qcom,pm8916-regulators", .data = &pm8916_regulators },
+ { .compatible = "qcom,pm8941-regulators", .data = &pm8941_regulators },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_spmi_regulator_match);
+
+static int qcom_spmi_regulator_probe(struct platform_device *pdev)
+{
+ const struct spmi_regulator_data *reg;
+ const struct of_device_id *match;
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ struct spmi_regulator *vreg;
+ struct regmap *regmap;
+ const char *name;
+ struct device *dev = &pdev->dev;
+ int ret;
+ struct list_head *vreg_list;
+
+ vreg_list = devm_kzalloc(dev, sizeof(*vreg_list), GFP_KERNEL);
+ if (!vreg_list)
+ return -ENOMEM;
+ INIT_LIST_HEAD(vreg_list);
+ platform_set_drvdata(pdev, vreg_list);
+
+ regmap = dev_get_regmap(dev->parent, NULL);
+ if (!regmap)
+ return -ENODEV;
+
+ match = of_match_device(qcom_spmi_regulator_match, &pdev->dev);
+ if (!match)
+ return -ENODEV;
+
+ for (reg = match->data; reg->name; reg++) {
+ vreg = devm_kzalloc(dev, sizeof(*vreg), GFP_KERNEL);
+ if (!vreg)
+ return -ENOMEM;
+
+ vreg->dev = dev;
+ vreg->base = reg->base;
+ vreg->regmap = regmap;
+
+ if (reg->ocp) {
+ vreg->ocp_irq = platform_get_irq_byname(pdev, reg->ocp);
+ if (vreg->ocp_irq < 0) {
+ ret = vreg->ocp_irq;
+ goto err;
+ }
+ }
+
+ vreg->desc.id = -1;
+ vreg->desc.owner = THIS_MODULE;
+ vreg->desc.type = REGULATOR_VOLTAGE;
+ vreg->desc.name = name = reg->name;
+ vreg->desc.supply_name = reg->supply;
+ vreg->desc.of_match = reg->name;
+ vreg->desc.of_parse_cb = spmi_regulator_of_parse;
+ vreg->desc.of_map_mode = spmi_regulator_of_map_mode;
+
+ ret = spmi_regulator_match(vreg, reg->force_type);
+ if (ret)
+ goto err;
+
+ config.dev = dev;
+ config.driver_data = vreg;
+ rdev = devm_regulator_register(dev, &vreg->desc, &config);
+ if (IS_ERR(rdev)) {
+ dev_err(dev, "failed to register %s\n", name);
+ ret = PTR_ERR(rdev);
+ goto err;
+ }
+
+ INIT_LIST_HEAD(&vreg->node);
+ list_add(&vreg->node, vreg_list);
+ }
+
+ return 0;
+
+err:
+ list_for_each_entry(vreg, vreg_list, node)
+ if (vreg->ocp_irq)
+ cancel_delayed_work_sync(&vreg->ocp_work);
+ return ret;
+}
+
+static int qcom_spmi_regulator_remove(struct platform_device *pdev)
+{
+ struct spmi_regulator *vreg;
+ struct list_head *vreg_list = platform_get_drvdata(pdev);
+
+ list_for_each_entry(vreg, vreg_list, node)
+ if (vreg->ocp_irq)
+ cancel_delayed_work_sync(&vreg->ocp_work);
+
+ return 0;
+}
+
+static struct platform_driver qcom_spmi_regulator_driver = {
+ .driver = {
+ .name = "qcom-spmi-regulator",
+ .of_match_table = qcom_spmi_regulator_match,
+ },
+ .probe = qcom_spmi_regulator_probe,
+ .remove = qcom_spmi_regulator_remove,
+};
+module_platform_driver(qcom_spmi_regulator_driver);
+
+MODULE_DESCRIPTION("Qualcomm SPMI PMIC regulator driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:qcom-spmi-regulator");
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Cc: <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
---
Documentation/devicetree/bindings/regulator/regulator.txt | 2 ++
drivers/regulator/core.c | 2 ++
drivers/regulator/of_regulator.c | 3 +++
include/linux/regulator/machine.h | 3 +++
4 files changed, 10 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index abb26b58c83e..553d2d0fe6d9 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -37,6 +37,8 @@ Optional properties:
- regulator-initial-mode: initial operating mode. The set of possible operating
modes depends on the capabilities of every hardware so each device binding
documentation explains which values the regulator supports.
+- regulator-system-load: Load in uA present on regulator that is not captured by
+ any consumer request.
Deprecated properties:
- regulator-compatible: If a regulator chip contains multiple
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 9dba0a3d4526..ab383dfe5386 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -678,6 +678,8 @@ static int drms_uA_update(struct regulator_dev *rdev)
list_for_each_entry(sibling, &rdev->consumer_list, list)
current_uA += sibling->uA_load;
+ current_uA += rdev->constraints->system_load;
+
if (rdev->desc->ops->set_load) {
/* set the optimum mode for our new total regulator load */
err = rdev->desc->ops->set_load(rdev, current_uA);
diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c
index 856c17d69b7e..b44da860ac22 100644
--- a/drivers/regulator/of_regulator.c
+++ b/drivers/regulator/of_regulator.c
@@ -95,6 +95,9 @@ static void of_get_regulation_constraints(struct device_node *np,
}
}
+ if (!of_property_read_u32(np, "regulator-system-load", &pval))
+ constraints->system_load = pval;
+
for (i = 0; i < ARRAY_SIZE(regulator_states); i++) {
switch (i) {
case PM_SUSPEND_MEM:
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index b07562e082c4..01526559c8c3 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -75,6 +75,7 @@ struct regulator_state {
*
* @min_uA: Smallest current consumers may set.
* @max_uA: Largest current consumers may set.
+ * @system_load: Load that isn't captured by any consumer requests.
*
* @valid_modes_mask: Mask of modes which may be configured by consumers.
* @valid_ops_mask: Operations which may be performed by consumers.
@@ -112,6 +113,8 @@ struct regulation_constraints {
int min_uA;
int max_uA;
+ int system_load;
+
/* valid regulator operating modes for this machine */
unsigned int valid_modes_mask;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Cc: <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
---
Documentation/devicetree/bindings/regulator/regulator.txt | 1 +
drivers/regulator/core.c | 8 ++++++++
drivers/regulator/of_regulator.c | 2 ++
include/linux/regulator/driver.h | 5 +++++
include/linux/regulator/machine.h | 2 ++
5 files changed, 18 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index 553d2d0fe6d9..6c79fd70ab5a 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -39,6 +39,7 @@ Optional properties:
documentation explains which values the regulator supports.
- regulator-system-load: Load in uA present on regulator that is not captured by
any consumer request.
+- regulator-pull-down: Enable pull down resistor when the regulator is disabled.
Deprecated properties:
- regulator-compatible: If a regulator chip contains multiple
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index ab383dfe5386..1d6172a9f65c 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -1051,6 +1051,14 @@ static int set_machine_constraints(struct regulator_dev *rdev,
}
}
+ if (rdev->constraints->pull_down && ops->set_pull_down) {
+ ret = ops->set_pull_down(rdev);
+ if (ret < 0) {
+ rdev_err(rdev, "failed to set pull down\n");
+ goto out;
+ }
+ }
+
print_constraints(rdev);
return 0;
out:
diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c
index b44da860ac22..237b014666fa 100644
--- a/drivers/regulator/of_regulator.c
+++ b/drivers/regulator/of_regulator.c
@@ -67,6 +67,8 @@ static void of_get_regulation_constraints(struct device_node *np,
if (!constraints->always_on) /* status change should be possible. */
constraints->valid_ops_mask |= REGULATOR_CHANGE_STATUS;
+ constraints->pull_down = of_property_read_bool(np, "regulator-pull-down");
+
if (of_property_read_bool(np, "regulator-allow-bypass"))
constraints->valid_ops_mask |= REGULATOR_CHANGE_BYPASS;
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index fffa688ac3a7..5eb85e152eb7 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -121,6 +121,9 @@ struct regulator_linear_range {
* @set_suspend_mode: Set the operating mode for the regulator when the
* system is suspended.
*
+ * @set_pull_down: Configure the regulator to pull down when the regulator
+ * is disabled.
+ *
* This struct describes regulator operations which can be implemented by
* regulator chip drivers.
*/
@@ -187,6 +190,8 @@ struct regulator_ops {
/* set regulator suspend operating mode (defined in consumer.h) */
int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode);
+
+ int (*set_pull_down) (struct regulator_dev *);
};
/*
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index 01526559c8c3..8ffb0619a03c 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -87,6 +87,7 @@ struct regulator_state {
* applied.
* @apply_uV: Apply the voltage constraint when initialising.
* @ramp_disable: Disable ramp delay when initialising or when setting voltage.
+ * @pull_down: Enable pull down when regulator is disabled.
*
* @input_uV: Input voltage for regulator when supplied by another regulator.
*
@@ -141,6 +142,7 @@ struct regulation_constraints {
unsigned boot_on:1; /* bootloader/firmware enabled regulator */
unsigned apply_uV:1; /* apply uV constraint if min == max */
unsigned ramp_disable:1; /* disable ramp delay */
+ unsigned pull_down:1; /* pull down resistor when regulator off */
};
/**
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Cc: <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
---
Documentation/devicetree/bindings/regulator/regulator.txt | 1 +
drivers/regulator/core.c | 8 ++++++++
drivers/regulator/of_regulator.c | 3 +++
include/linux/regulator/driver.h | 2 ++
include/linux/regulator/machine.h | 1 +
5 files changed, 15 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index 6c79fd70ab5a..4b1df61ccbd7 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -19,6 +19,7 @@ Optional properties:
design requires. This property describes the total system ramp time
required due to the combination of internal ramping of the regulator itself,
and board design issues such as trace capacitance and load on the supply.
+- regulator-soft-start: Enable soft start so that voltage ramps slowly
- regulator-state-mem sub-root node for Suspend-to-RAM mode
: suspend to memory, the device goes to sleep, but all data stored in memory,
only some external interrupt can wake the device.
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 1d6172a9f65c..88622fc76b81 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -1059,6 +1059,14 @@ static int set_machine_constraints(struct regulator_dev *rdev,
}
}
+ if (rdev->constraints->soft_start && ops->set_soft_start) {
+ ret = ops->set_soft_start(rdev);
+ if (ret < 0) {
+ rdev_err(rdev, "failed to set soft start\n");
+ goto out;
+ }
+ }
+
print_constraints(rdev);
return 0;
out:
diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c
index 237b014666fa..72576dd9bf7b 100644
--- a/drivers/regulator/of_regulator.c
+++ b/drivers/regulator/of_regulator.c
@@ -84,6 +84,9 @@ static void of_get_regulation_constraints(struct device_node *np,
if (!ret)
constraints->enable_time = pval;
+ constraints->soft_start = of_property_read_bool(np,
+ "regulator-soft-start");
+
if (!of_property_read_u32(np, "regulator-initial-mode", &pval)) {
if (desc && desc->of_map_mode) {
ret = desc->of_map_mode(pval);
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index 5eb85e152eb7..02e1e8d4b1bb 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -161,6 +161,8 @@ struct regulator_ops {
unsigned int old_selector,
unsigned int new_selector);
+ int (*set_soft_start) (struct regulator_dev *);
+
/* report regulator status ... most other accessors report
* control inputs, this reports results of combining inputs
* from Linux (and other sources) with the actual load.
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index 8ffb0619a03c..7f7d0a3fe1e1 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -142,6 +142,7 @@ struct regulation_constraints {
unsigned boot_on:1; /* bootloader/firmware enabled regulator */
unsigned apply_uV:1; /* apply uV constraint if min == max */
unsigned ramp_disable:1; /* disable ramp delay */
+ unsigned soft_start:1; /* ramp voltage slowly */
unsigned pull_down:1; /* pull down resistor when regulator off */
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Cc: <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
---
Documentation/devicetree/bindings/regulator/regulator.txt | 1 +
drivers/regulator/core.c | 9 +++++++++
drivers/regulator/of_regulator.c | 4 ++++
include/linux/regulator/driver.h | 3 +++
include/linux/regulator/machine.h | 2 ++
5 files changed, 19 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index 4b1df61ccbd7..e29db73e55f4 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -7,6 +7,7 @@ Optional properties:
- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops
- regulator-min-microamp: smallest current consumers may set
- regulator-max-microamp: largest current consumers may set
+- regulator-input-current-limit-microamp: maximum input current regulator allows
- regulator-always-on: boolean, regulator should never be disabled
- regulator-boot-on: bootloader/firmware enabled regulator
- regulator-allow-bypass: allow the regulator to go into bypass mode
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 88622fc76b81..46c253e85c9e 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -1008,6 +1008,15 @@ static int set_machine_constraints(struct regulator_dev *rdev,
if (ret != 0)
goto out;
+ if (rdev->constraints->ilim_uA && ops->set_input_current_limit) {
+ ret = ops->set_input_current_limit(rdev,
+ rdev->constraints->ilim_uA);
+ if (ret < 0) {
+ rdev_err(rdev, "failed to set input limit\n");
+ goto out;
+ }
+ }
+
/* do we need to setup our suspend state */
if (rdev->constraints->initial_state) {
ret = suspend_prepare(rdev, rdev->constraints->initial_state);
diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c
index 72576dd9bf7b..b41d80acbc4a 100644
--- a/drivers/regulator/of_regulator.c
+++ b/drivers/regulator/of_regulator.c
@@ -58,6 +58,10 @@ static void of_get_regulation_constraints(struct device_node *np,
if (!of_property_read_u32(np, "regulator-max-microamp", &pval))
constraints->max_uA = pval;
+ if (!of_property_read_u32(np, "regulator-input-current-limit-microamp",
+ &pval))
+ constraints->ilim_uA = pval;
+
/* Current change possible? */
if (constraints->min_uA != constraints->max_uA)
constraints->valid_ops_mask |= REGULATOR_CHANGE_CURRENT;
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index 02e1e8d4b1bb..1de82b081f5a 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -91,6 +91,7 @@ struct regulator_linear_range {
* @set_current_limit: Configure a limit for a current-limited regulator.
* The driver should select the current closest to max_uA.
* @get_current_limit: Get the configured limit for a current-limited regulator.
+ * @set_input_current_limit: Configure an input limit.
*
* @set_mode: Set the configured operating mode for the regulator.
* @get_mode: Get the configured operating mode for the regulator.
@@ -145,6 +146,8 @@ struct regulator_ops {
int min_uA, int max_uA);
int (*get_current_limit) (struct regulator_dev *);
+ int (*set_input_current_limit) (struct regulator_dev *, int lim_uA);
+
/* enable/disable regulator */
int (*enable) (struct regulator_dev *);
int (*disable) (struct regulator_dev *);
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index 7f7d0a3fe1e1..85a3b457de51 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -75,6 +75,7 @@ struct regulator_state {
*
* @min_uA: Smallest current consumers may set.
* @max_uA: Largest current consumers may set.
+ * @ilim_uA: Maximum input current.
* @system_load: Load that isn't captured by any consumer requests.
*
* @valid_modes_mask: Mask of modes which may be configured by consumers.
@@ -113,6 +114,7 @@ struct regulation_constraints {
/* current output range (inclusive) - for current control */
int min_uA;
int max_uA;
+ int ilim_uA;
int system_load;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Add support for over current protection (OCP), pin control
selection, soft start and soft start strength, auto-mode, input
current limiting, and pull down.
Cc: <[email protected]>
Signed-off-by: Stephen Boyd <[email protected]>
---
Changes from v1:
* New patch split from original SPMI regulator driver
.../bindings/regulator/qcom,spmi-regulator.txt | 62 +++++
drivers/regulator/qcom_spmi-regulator.c | 298 ++++++++++++++++++++-
2 files changed, 358 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 75b4604bad07..ab01a152e930 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -99,6 +99,68 @@ see regulator.txt - with additional custom properties described below:
soft start are active all the time. 0 = Set initial mode to
low power mode (LPM).
+- qcom,auto-mode-enable:
+ Usage: optional
+ Value type: <u32>
+ Description: 1 = Enable automatic hardware selection of regulator
+ mode (HPM vs LPM); not available on boost type
+ regulators. 0 = Disable auto mode selection.
+
+- qcom,ocp-enable:
+ Usage: optional
+ Value type: <u32>
+ Description: 1 = Allow over current protection (OCP) to be enabled for
+ voltage switch type regulators so that they latch off
+ automatically when over current is detected. OCP is
+ enabled when in HPM or auto mode. 0 = Disable OCP.
+
+- qcom,ocp-max-retries:
+ Usage: optional
+ Value type: <u32>
+ Description: Maximum number of times to try toggling a voltage switch
+ off and back on as a result of consecutive over current
+ events.
+
+- qcom,ocp-retry-delay:
+ Usage: optional
+ Value type: <u32>
+ Description: Time to delay in milliseconds between each voltage switch
+ toggle after an over current event takes place.
+
+- qcom,pin-ctrl-enable:
+ Usage: optional
+ Value type: <u32>
+ Description: Bit mask specifying which hardware pins should be used to
+ enable the regulator, if any; supported bits are:
+ 0 = ignore all hardware enable signals
+ BIT(0) = follow HW0_EN signal
+ BIT(1) = follow HW1_EN signal
+ BIT(2) = follow HW2_EN signal
+ BIT(3) = follow HW3_EN signal
+
+- qcom,pin-ctrl-hpm:
+ Usage: optional
+ Value type: <u32>
+ Description: Bit mask specifying which hardware pins should be used to
+ force the regulator into high power mode, if any;
+ supported bits are:
+ 0 = ignore all hardware enable signals
+ BIT(0) = follow HW0_EN signal
+ BIT(1) = follow HW1_EN signal
+ BIT(2) = follow HW2_EN signal
+ BIT(3) = follow HW3_EN signal
+ BIT(4) = follow PMIC awake state
+
+- qcom,vs-soft-start-strength:
+ Usage: optional
+ Value type: <u32>
+ Description: This property sets the soft start strength for voltage
+ switch type regulators; supported values are:
+ 0 = 0.05 uA
+ 1 = 0.25 uA
+ 2 = 0.55 uA
+ 3 = 0.75 uA
+
Example:
regulators {
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 3df635d101c4..f26b3b29cb04 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -26,6 +26,86 @@
#include <linux/regmap.h>
#include <linux/list.h>
+/* Pin control enable input pins. */
+#define SPMI_REGULATOR_PIN_CTRL_ENABLE_NONE 0x00
+#define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN0 0x01
+#define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN1 0x02
+#define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN2 0x04
+#define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN3 0x08
+#define SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT 0x10
+
+/* Pin control high power mode input pins. */
+#define SPMI_REGULATOR_PIN_CTRL_HPM_NONE 0x00
+#define SPMI_REGULATOR_PIN_CTRL_HPM_EN0 0x01
+#define SPMI_REGULATOR_PIN_CTRL_HPM_EN1 0x02
+#define SPMI_REGULATOR_PIN_CTRL_HPM_EN2 0x04
+#define SPMI_REGULATOR_PIN_CTRL_HPM_EN3 0x08
+#define SPMI_REGULATOR_PIN_CTRL_HPM_SLEEP_B 0x10
+#define SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT 0x20
+
+/*
+ * Used with enable parameters to specify that hardware default register values
+ * should be left unaltered.
+ */
+#define SPMI_REGULATOR_USE_HW_DEFAULT 2
+
+/* Soft start strength of a voltage switch type regulator */
+enum spmi_vs_soft_start_str {
+ SPMI_VS_SOFT_START_STR_0P05_UA = 0,
+ SPMI_VS_SOFT_START_STR_0P25_UA,
+ SPMI_VS_SOFT_START_STR_0P55_UA,
+ SPMI_VS_SOFT_START_STR_0P75_UA,
+ SPMI_VS_SOFT_START_STR_HW_DEFAULT,
+};
+
+/**
+ * struct spmi_regulator_init_data - spmi-regulator initialization data
+ * @pin_ctrl_enable: Bit mask specifying which hardware pins should be
+ * used to enable the regulator, if any
+ * Value should be an ORing of
+ * SPMI_REGULATOR_PIN_CTRL_ENABLE_* constants. If
+ * the bit specified by
+ * SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT is
+ * set, then pin control enable hardware registers
+ * will not be modified.
+ * @pin_ctrl_hpm: Bit mask specifying which hardware pins should be
+ * used to force the regulator into high power
+ * mode, if any
+ * Value should be an ORing of
+ * SPMI_REGULATOR_PIN_CTRL_HPM_* constants. If
+ * the bit specified by
+ * SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT is
+ * set, then pin control mode hardware registers
+ * will not be modified.
+ * @vs_soft_start_strength: This parameter sets the soft start strength for
+ * voltage switch type regulators. Its value
+ * should be one of SPMI_VS_SOFT_START_STR_*. If
+ * its value is SPMI_VS_SOFT_START_STR_HW_DEFAULT,
+ * then the soft start strength will be left at its
+ * default hardware value.
+ * @auto_mode_enable: 1 = Enable automatic hardware selection of regulator
+ * mode (HPM vs LPM). Auto mode is not available
+ * on boost type regulators
+ * 0 = Disable auto mode selection
+ * SPMI_REGULATOR_USE_HW_DEFAULT = do not modify
+ * auto mode state
+ * @ocp_enable: 1 = Allow over current protection (OCP) to be
+ * enabled for voltage switch type regulators so
+ * that they latch off automatically when over
+ * current is detected. OCP is enabled when in HPM
+ * or auto mode.
+ * 0 = Disable OCP
+ * QPNP_REGULATOR_USE_HW_DEFAULT = do not modify
+ * OCP state
+ */
+struct spmi_regulator_init_data {
+ unsigned pin_ctrl_enable;
+ unsigned pin_ctrl_hpm;
+ enum spmi_vs_soft_start_str vs_soft_start_strength;
+ int auto_mode_enable;
+ int ocp_enable;
+};
+
/* These types correspond to unique register layouts. */
enum spmi_regulator_logical_type {
SPMI_REGULATOR_LOGICAL_TYPE_SMPS,
@@ -824,6 +904,72 @@ spmi_regulator_common_set_load(struct regulator_dev *rdev, int load_uA)
return spmi_regulator_common_set_mode(rdev, mode);
}
+static int spmi_regulator_common_set_pull_down(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ unsigned int mask = SPMI_COMMON_PULL_DOWN_ENABLE_MASK;
+
+ return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_PULL_DOWN,
+ mask, mask);
+}
+
+static int spmi_regulator_common_set_soft_start(struct regulator_dev *rdev)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ unsigned int mask = SPMI_LDO_SOFT_START_ENABLE_MASK;
+
+ return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_SOFT_START,
+ mask, mask);
+}
+
+static int spmi_regulator_set_ilim(struct regulator_dev *rdev, int ilim_uA)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ enum spmi_regulator_logical_type type = vreg->logical_type;
+ unsigned int current_reg;
+ u8 reg;
+ u8 mask = SPMI_BOOST_CURRENT_LIMIT_MASK |
+ SPMI_BOOST_CURRENT_LIMIT_ENABLE_MASK;
+
+ if (type == SPMI_REGULATOR_LOGICAL_TYPE_BOOST)
+ current_reg = SPMI_BOOST_REG_CURRENT_LIMIT;
+ else
+ current_reg = SPMI_BOOST_BYP_REG_CURRENT_LIMIT;
+
+ switch (ilim_uA) {
+ case 0 ... 300:
+ reg = 0;
+ break;
+ case 301 ... 600:
+ reg = 1;
+ break;
+ case 601 ... 900:
+ reg = 2;
+ break;
+ case 901 ... 1200:
+ reg = 3;
+ break;
+ case 1201 ... 1500:
+ reg = 4;
+ break;
+ case 1501 ... 1800:
+ reg = 5;
+ break;
+ case 1801 ... 2100:
+ reg = 6;
+ break;
+ case 2101 ... 2400:
+ reg = 7;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ reg |= SPMI_BOOST_CURRENT_LIMIT_ENABLE_MASK;
+
+ return spmi_vreg_update_bits(vreg, current_reg, reg, mask);
+}
+
static int spmi_regulator_vs_clear_ocp(struct spmi_regulator *vreg)
{
int ret;
@@ -897,6 +1043,7 @@ static struct regulator_ops spmi_smps_ops = {
.set_mode = spmi_regulator_common_set_mode,
.get_mode = spmi_regulator_common_get_mode,
.set_load = spmi_regulator_common_set_load,
+ .set_pull_down = spmi_regulator_common_set_pull_down,
};
static struct regulator_ops spmi_ldo_ops = {
@@ -911,6 +1058,8 @@ static struct regulator_ops spmi_ldo_ops = {
.set_load = spmi_regulator_common_set_load,
.set_bypass = spmi_regulator_common_set_bypass,
.get_bypass = spmi_regulator_common_get_bypass,
+ .set_pull_down = spmi_regulator_common_set_pull_down,
+ .set_soft_start = spmi_regulator_common_set_soft_start,
};
static struct regulator_ops spmi_ln_ldo_ops = {
@@ -928,6 +1077,8 @@ static struct regulator_ops spmi_vs_ops = {
.enable = spmi_regulator_vs_enable,
.disable = spmi_regulator_common_disable,
.is_enabled = spmi_regulator_common_is_enabled,
+ .set_pull_down = spmi_regulator_common_set_pull_down,
+ .set_soft_start = spmi_regulator_common_set_soft_start,
};
static struct regulator_ops spmi_boost_ops = {
@@ -937,6 +1088,7 @@ static struct regulator_ops spmi_boost_ops = {
.set_voltage = spmi_regulator_single_range_set_voltage,
.get_voltage = spmi_regulator_single_range_get_voltage,
.list_voltage = spmi_regulator_common_list_voltage,
+ .set_input_current_limit = spmi_regulator_set_ilim,
};
static struct regulator_ops spmi_ftsmps_ops = {
@@ -950,6 +1102,7 @@ static struct regulator_ops spmi_ftsmps_ops = {
.set_mode = spmi_regulator_common_set_mode,
.get_mode = spmi_regulator_common_get_mode,
.set_load = spmi_regulator_common_set_load,
+ .set_pull_down = spmi_regulator_common_set_pull_down,
};
static struct regulator_ops spmi_ult_lo_smps_ops = {
@@ -962,6 +1115,7 @@ static struct regulator_ops spmi_ult_lo_smps_ops = {
.set_mode = spmi_regulator_common_set_mode,
.get_mode = spmi_regulator_common_get_mode,
.set_load = spmi_regulator_common_set_load,
+ .set_pull_down = spmi_regulator_common_set_pull_down,
};
static struct regulator_ops spmi_ult_ho_smps_ops = {
@@ -974,6 +1128,7 @@ static struct regulator_ops spmi_ult_ho_smps_ops = {
.set_mode = spmi_regulator_common_set_mode,
.get_mode = spmi_regulator_common_get_mode,
.set_load = spmi_regulator_common_set_load,
+ .set_pull_down = spmi_regulator_common_set_pull_down,
};
static struct regulator_ops spmi_ult_ldo_ops = {
@@ -988,6 +1143,8 @@ static struct regulator_ops spmi_ult_ldo_ops = {
.set_load = spmi_regulator_common_set_load,
.set_bypass = spmi_regulator_common_set_bypass,
.get_bypass = spmi_regulator_common_get_bypass,
+ .set_pull_down = spmi_regulator_common_set_pull_down,
+ .set_soft_start = spmi_regulator_common_set_soft_start,
};
/* Maximum possible digital major revision value */
@@ -1152,6 +1309,132 @@ static int spmi_regulator_ftsmps_init_slew_rate(struct spmi_regulator *vreg)
return ret;
}
+static int spmi_regulator_init_registers(struct spmi_regulator *vreg,
+ const struct spmi_regulator_init_data *data)
+{
+ int ret;
+ enum spmi_regulator_logical_type type;
+ u8 ctrl_reg[8], reg, mask;
+
+ type = vreg->logical_type;
+
+ ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, ctrl_reg, 8);
+ if (ret)
+ return ret;
+
+ /* Set up enable pin control. */
+ if ((type == SPMI_REGULATOR_LOGICAL_TYPE_SMPS
+ || type == SPMI_REGULATOR_LOGICAL_TYPE_LDO
+ || type == SPMI_REGULATOR_LOGICAL_TYPE_VS)
+ && !(data->pin_ctrl_enable
+ & SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT)) {
+ ctrl_reg[SPMI_COMMON_IDX_ENABLE] &=
+ ~SPMI_COMMON_ENABLE_FOLLOW_ALL_MASK;
+ ctrl_reg[SPMI_COMMON_IDX_ENABLE] |=
+ data->pin_ctrl_enable & SPMI_COMMON_ENABLE_FOLLOW_ALL_MASK;
+ }
+
+ /* Set up auto mode control. */
+ if ((type == SPMI_REGULATOR_LOGICAL_TYPE_SMPS
+ || type == SPMI_REGULATOR_LOGICAL_TYPE_LDO
+ || type == SPMI_REGULATOR_LOGICAL_TYPE_VS
+ || type == SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS)
+ && (data->auto_mode_enable != SPMI_REGULATOR_USE_HW_DEFAULT)) {
+ ctrl_reg[SPMI_COMMON_IDX_MODE] &=
+ ~SPMI_COMMON_MODE_AUTO_MASK;
+ ctrl_reg[SPMI_COMMON_IDX_MODE] |=
+ (data->auto_mode_enable ? SPMI_COMMON_MODE_AUTO_MASK : 0);
+ }
+
+ /* Set up mode pin control. */
+ if ((type == SPMI_REGULATOR_LOGICAL_TYPE_SMPS
+ || type == SPMI_REGULATOR_LOGICAL_TYPE_LDO)
+ && !(data->pin_ctrl_hpm
+ & SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT)) {
+ ctrl_reg[SPMI_COMMON_IDX_MODE] &=
+ ~SPMI_COMMON_MODE_FOLLOW_ALL_MASK;
+ ctrl_reg[SPMI_COMMON_IDX_MODE] |=
+ data->pin_ctrl_hpm & SPMI_COMMON_MODE_FOLLOW_ALL_MASK;
+ }
+
+ if (type == SPMI_REGULATOR_LOGICAL_TYPE_VS
+ && !(data->pin_ctrl_hpm & SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT)) {
+ ctrl_reg[SPMI_COMMON_IDX_MODE] &=
+ ~SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK;
+ ctrl_reg[SPMI_COMMON_IDX_MODE] |=
+ data->pin_ctrl_hpm & SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK;
+ }
+
+ if ((type == SPMI_REGULATOR_LOGICAL_TYPE_ULT_LO_SMPS
+ || type == SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS
+ || type == SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO)
+ && !(data->pin_ctrl_hpm
+ & SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT)) {
+ ctrl_reg[SPMI_COMMON_IDX_MODE] &=
+ ~SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK;
+ ctrl_reg[SPMI_COMMON_IDX_MODE] |=
+ data->pin_ctrl_hpm & SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK;
+ }
+
+ /* Write back any control register values that were modified. */
+ ret = spmi_vreg_write(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, ctrl_reg, 8);
+ if (ret)
+ return ret;
+
+ /* Set soft start strength and over current protection for VS. */
+ if (type == SPMI_REGULATOR_LOGICAL_TYPE_VS) {
+ if (data->vs_soft_start_strength
+ != SPMI_VS_SOFT_START_STR_HW_DEFAULT) {
+ reg = data->vs_soft_start_strength
+ & SPMI_VS_SOFT_START_SEL_MASK;
+ mask = SPMI_VS_SOFT_START_SEL_MASK;
+ ret = spmi_vreg_update_bits(vreg,
+ SPMI_VS_REG_SOFT_START,
+ reg, mask);
+ if (ret)
+ return ret;
+ }
+
+ if (data->ocp_enable != SPMI_REGULATOR_USE_HW_DEFAULT) {
+ reg = data->ocp_enable ? SPMI_VS_OCP_NO_OVERRIDE
+ : SPMI_VS_OCP_OVERRIDE;
+ ret = spmi_vreg_write(vreg, SPMI_VS_REG_OCP, ®, 1);
+ if (ret)
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static void spmi_regulator_get_dt_config(struct spmi_regulator *vreg,
+ struct device_node *node, struct spmi_regulator_init_data *data)
+{
+ /*
+ * Initialize configuration parameters to use hardware default in case
+ * no value is specified via device tree.
+ */
+ data->auto_mode_enable = SPMI_REGULATOR_USE_HW_DEFAULT;
+ data->ocp_enable = SPMI_REGULATOR_USE_HW_DEFAULT;
+ data->pin_ctrl_enable = SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT;
+ data->pin_ctrl_hpm = SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT;
+ data->vs_soft_start_strength = SPMI_VS_SOFT_START_STR_HW_DEFAULT;
+
+ /* These bindings are optional, so it is okay if they aren't found. */
+ of_property_read_u32(node, "qcom,auto-mode-enable",
+ &data->auto_mode_enable);
+ of_property_read_u32(node, "qcom,ocp-enable", &data->ocp_enable);
+ of_property_read_u32(node, "qcom,ocp-max-retries",
+ &vreg->ocp_max_retries);
+ of_property_read_u32(node, "qcom,ocp-retry-delay",
+ &vreg->ocp_retry_delay_ms);
+ of_property_read_u32(node, "qcom,pin-ctrl-enable",
+ &data->pin_ctrl_enable);
+ of_property_read_u32(node, "qcom,pin-ctrl-hpm", &data->pin_ctrl_hpm);
+ of_property_read_u32(node, "qcom,vs-soft-start-strength",
+ &data->vs_soft_start_strength);
+}
+
static unsigned int spmi_regulator_of_map_mode(unsigned int mode)
{
if (mode)
@@ -1164,12 +1447,23 @@ static int spmi_regulator_of_parse(struct device_node *node,
const struct regulator_desc *desc,
struct regulator_config *config)
{
+ struct spmi_regulator_init_data data = { };
struct spmi_regulator *vreg = config->driver_data;
struct device *dev = config->dev;
int ret;
- vreg->ocp_max_retries = SPMI_VS_OCP_DEFAULT_MAX_RETRIES;
- vreg->ocp_retry_delay_ms = SPMI_VS_OCP_DEFAULT_RETRY_DELAY_MS;
+ spmi_regulator_get_dt_config(vreg, node, &data);
+
+ if (!vreg->ocp_max_retries)
+ vreg->ocp_max_retries = SPMI_VS_OCP_DEFAULT_MAX_RETRIES;
+ if (!vreg->ocp_retry_delay_ms)
+ vreg->ocp_retry_delay_ms = SPMI_VS_OCP_DEFAULT_RETRY_DELAY_MS;
+
+ ret = spmi_regulator_init_registers(vreg, &data);
+ if (ret) {
+ dev_err(dev, "common initialization failed, ret=%d\n", ret);
+ return ret;
+ }
if (vreg->logical_type == SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS) {
ret = spmi_regulator_ftsmps_init_slew_rate(vreg);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
On Thu, Jun 11, 2015 at 7:37 PM, Stephen Boyd <[email protected]> wrote:
> Add support for over current protection (OCP), pin control
> selection, soft start and soft start strength, auto-mode, input
> current limiting, and pull down.
>
> Cc: <[email protected]>
> Signed-off-by: Stephen Boyd <[email protected]>
> ---
>
> Changes from v1:
> * New patch split from original SPMI regulator driver
>
> .../bindings/regulator/qcom,spmi-regulator.txt | 62 +++++
> drivers/regulator/qcom_spmi-regulator.c | 298 ++++++++++++++++++++-
> 2 files changed, 358 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
> index 75b4604bad07..ab01a152e930 100644
> --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
> +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
> @@ -99,6 +99,68 @@ see regulator.txt - with additional custom properties described below:
> soft start are active all the time. 0 = Set initial mode to
> low power mode (LPM).
>
> +- qcom,auto-mode-enable:
Auto regulator modes are fairly common. Can't we have a common property here?
> + Usage: optional
> + Value type: <u32>
This can be bool. Unless we want to have a mode property with "auto"
being one possible value.
> + Description: 1 = Enable automatic hardware selection of regulator
> + mode (HPM vs LPM); not available on boost type
> + regulators. 0 = Disable auto mode selection.
> +
> +- qcom,ocp-enable:
> + Usage: optional
> + Value type: <u32>
> + Description: 1 = Allow over current protection (OCP) to be enabled for
> + voltage switch type regulators so that they latch off
> + automatically when over current is detected. OCP is
> + enabled when in HPM or auto mode. 0 = Disable OCP.
This seems common too.
> +
> +- qcom,ocp-max-retries:
> + Usage: optional
> + Value type: <u32>
> + Description: Maximum number of times to try toggling a voltage switch
> + off and back on as a result of consecutive over current
> + events.
> +
> +- qcom,ocp-retry-delay:
> + Usage: optional
> + Value type: <u32>
> + Description: Time to delay in milliseconds between each voltage switch
> + toggle after an over current event takes place.
These 2 are perhaps less common. I hope I don't have a device that does this. :)
Rob
On Thu, Jun 11, 2015 at 05:37:02PM -0700, Stephen Boyd wrote:
> Add an SPMI regulator driver for Qualcomm's PM8841, PM8941, and
> PM8916 PMICs. This driver is based largely on code from
> codeaurora.org[1].
This doesn't apply against current code, please check and resend.
On Thu, Jun 11, 2015 at 05:37:03PM -0700, Stephen Boyd wrote:
> Some regulators have a fixed load that isn't captured by
> consumers that the kernel knows about. Add a constraint to
> support this.
Applied, thanks.
On Thu, Jun 11, 2015 at 05:37:04PM -0700, Stephen Boyd wrote:
> Some regulators need to be configured to pull down a resistor
> when the regulator is disabled. Add an op (set_pull_down) and a
> DT property + constraint to support this.
Applied, thanks.
On Thu, Jun 11, 2015 at 05:37:05PM -0700, Stephen Boyd wrote:
> Some regulators support a "soft start" feature where the voltage
> ramps up slowly when the regulator is enabled. Add an op
> (set_soft_start) and a DT property + constraint to support this.
Applied, thanks.
On Thu, Jun 11, 2015 at 05:37:06PM -0700, Stephen Boyd wrote:
> Some regulators can limit their input current (typically annotated
> as ilim). Add an op (set_input_current_limit) and a DT property +
> constraint to support this.
Applied, thanks.
On 06/11, Rob Herring wrote:
> On Thu, Jun 11, 2015 at 7:37 PM, Stephen Boyd <[email protected]> wrote:
> > Add support for over current protection (OCP), pin control
> > selection, soft start and soft start strength, auto-mode, input
> > current limiting, and pull down.
> >
> > Cc: <[email protected]>
> > Signed-off-by: Stephen Boyd <[email protected]>
> > ---
> >
> > Changes from v1:
> > * New patch split from original SPMI regulator driver
> >
> > .../bindings/regulator/qcom,spmi-regulator.txt | 62 +++++
> > drivers/regulator/qcom_spmi-regulator.c | 298 ++++++++++++++++++++-
> > 2 files changed, 358 insertions(+), 2 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
> > index 75b4604bad07..ab01a152e930 100644
> > --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
> > +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
> > @@ -99,6 +99,68 @@ see regulator.txt - with additional custom properties described below:
> > soft start are active all the time. 0 = Set initial mode to
> > low power mode (LPM).
> >
> > +- qcom,auto-mode-enable:
>
> Auto regulator modes are fairly common. Can't we have a common property here?
>
> > + Usage: optional
> > + Value type: <u32>
>
> This can be bool. Unless we want to have a mode property with "auto"
> being one possible value.
>From what I can tell we use this property as qcom,auto-mode-enable = <0>.
Put another way, that's qcom,auto-mode-disable. Should we have two
properties? Or is it better to mark all regulators explicitly with
either auto-mode-enable or the absence of such a property? The bindings
take an approach of giving all these "boolean" properties a 0 or 1 value
so that the absence of the property indicates that we should use the
default value in the hardware.
>
> > + Description: 1 = Enable automatic hardware selection of regulator
> > + mode (HPM vs LPM); not available on boost type
> > + regulators. 0 = Disable auto mode selection.
> > +
> > +- qcom,ocp-enable:
> > + Usage: optional
> > + Value type: <u32>
> > + Description: 1 = Allow over current protection (OCP) to be enabled for
> > + voltage switch type regulators so that they latch off
> > + automatically when over current is detected. OCP is
> > + enabled when in HPM or auto mode. 0 = Disable OCP.
>
> This seems common too.
Ok. I'll make up another patch for this one. Perhaps call it
regulator-over-current-protection?
>
> > +
> > +- qcom,ocp-max-retries:
> > + Usage: optional
> > + Value type: <u32>
> > + Description: Maximum number of times to try toggling a voltage switch
> > + off and back on as a result of consecutive over current
> > + events.
> > +
> > +- qcom,ocp-retry-delay:
> > + Usage: optional
> > + Value type: <u32>
> > + Description: Time to delay in milliseconds between each voltage switch
> > + toggle after an over current event takes place.
>
> These 2 are perhaps less common. I hope I don't have a device that does this. :)
>
:)
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
On 06/11/2015 08:13 PM, Rob Herring wrote:
> On Thu, Jun 11, 2015 at 7:37 PM, Stephen Boyd <[email protected]> wrote:
>> Add support for over current protection (OCP), pin control
>> selection, soft start and soft start strength, auto-mode, input
>> current limiting, and pull down.
>>
>> Cc: <[email protected]>
>> Signed-off-by: Stephen Boyd <[email protected]>
>> ---
>>
>> Changes from v1:
>> * New patch split from original SPMI regulator driver
>>
>> .../bindings/regulator/qcom,spmi-regulator.txt | 62 +++++
>> drivers/regulator/qcom_spmi-regulator.c | 298 ++++++++++++++++++++-
>> 2 files changed, 358 insertions(+), 2 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
>> index 75b4604bad07..ab01a152e930 100644
>> --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
>> +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
>> @@ -99,6 +99,68 @@ see regulator.txt - with additional custom properties described below:
>> soft start are active all the time. 0 = Set initial mode to
>> low power mode (LPM).
>>
>> +- qcom,auto-mode-enable:
> Auto regulator modes are fairly common. Can't we have a common property here?
Should we use regulator-init-mode? We could make
spmi_regulator_of_map_mode() turn "2" into REGULATOR_MODE_FAST and then
use that to enable auto mode.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
On Thu, Jun 11, 2015 at 8:13 PM, Rob Herring <[email protected]> wrote:
> On Thu, Jun 11, 2015 at 7:37 PM, Stephen Boyd <[email protected]> wrote:
>> Add support for over current protection (OCP), pin control
>> selection, soft start and soft start strength, auto-mode, input
>> current limiting, and pull down.
>>
>> Cc: <[email protected]>
>> Signed-off-by: Stephen Boyd <[email protected]>
>> ---
>>
>> Changes from v1:
>> * New patch split from original SPMI regulator driver
>>
>> .../bindings/regulator/qcom,spmi-regulator.txt | 62 +++++
>> drivers/regulator/qcom_spmi-regulator.c | 298 ++++++++++++++++++++-
>> 2 files changed, 358 insertions(+), 2 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
>> index 75b4604bad07..ab01a152e930 100644
>> --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
>> +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
>> @@ -99,6 +99,68 @@ see regulator.txt - with additional custom properties described below:
>> soft start are active all the time. 0 = Set initial mode to
>> low power mode (LPM).
>>
>> +- qcom,auto-mode-enable:
>
> Auto regulator modes are fairly common. Can't we have a common property here?
>
I went with a similar set of booleans for mode selection in the
initial rpm driver for family A, but Kumar objected to this. So there
I ended up with "qcom,force-mode" - taking an enum - instead (see
mfd/qcom-rpm.txt). It would be nice if the various regulator drivers
have similar bindings...
>> + Usage: optional
>> + Value type: <u32>
>
> This can be bool. Unless we want to have a mode property with "auto"
> being one possible value.
>
>> + Description: 1 = Enable automatic hardware selection of regulator
>> + mode (HPM vs LPM); not available on boost type
>> + regulators. 0 = Disable auto mode selection.
>> +
Regards,
Bjorn