2015-07-03 04:03:15

by Alison Wang

[permalink] [raw]
Subject: [PATCH] dts: ls1021a: audio: Add dts nodes for audio on LS1021A

This patch adds dts nodes for audio on LS1021A.

Signed-off-by: Alison Wang <[email protected]>
---
arch/arm/boot/dts/ls1021a-qds.dts | 71 +++++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/ls1021a-twr.dts | 63 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/ls1021a.dtsi | 14 ++++----
3 files changed, 142 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/ls1021a-qds.dts b/arch/arm/boot/dts/ls1021a-qds.dts
index f16a061..9533f1d 100644
--- a/arch/arm/boot/dts/ls1021a-qds.dts
+++ b/arch/arm/boot/dts/ls1021a-qds.dts
@@ -58,6 +58,57 @@
enet0_sgmii_phy = &sgmii_phy1c;
enet1_sgmii_phy = &sgmii_phy1d;
};
+
+ clocks {
+ sys_mclk: clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3p3v: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "Speaker Ext",
+ "Line", "Line In Jack";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "Microphone Jack", "Mic Bias",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "Speaker Ext", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ frame-master;
+ bitclock-master;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&codec>;
+ frame-master;
+ bitclock-master;
+ };
+ };
};

&dspi0 {
@@ -99,6 +150,7 @@
status = "okay";

pca9547: mux@77 {
+ compatible = "nxp,pca9547";
reg = <0x77>;
#address-cells = <1>;
#size-cells = <0>;
@@ -153,6 +205,21 @@
reg = <0x4c>;
};
};
+
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+
+ codec: sgtl5000@2a {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,sgtl5000";
+ reg = <0x2a>;
+ VDDA-supply = <&reg_3p3v>;
+ VDDIO-supply = <&reg_3p3v>;
+ clocks = <&sys_mclk 1>;
+ };
+ };
};
};

@@ -251,6 +318,10 @@
};
};

+&sai2 {
+ status = "okay";
+};
+
&uart0 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/ls1021a-twr.dts b/arch/arm/boot/dts/ls1021a-twr.dts
index 4b61766..a0d9ad6 100644
--- a/arch/arm/boot/dts/ls1021a-twr.dts
+++ b/arch/arm/boot/dts/ls1021a-twr.dts
@@ -56,6 +56,57 @@
enet0_sgmii_phy = &sgmii_phy2;
enet1_sgmii_phy = &sgmii_phy0;
};
+
+ clocks {
+ sys_mclk: clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3p3v: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "Speaker Ext",
+ "Line", "Line In Jack";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "Microphone Jack", "Mic Bias",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "Speaker Ext", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai1>;
+ frame-master;
+ bitclock-master;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&codec>;
+ frame-master;
+ bitclock-master;
+ };
+ };
};

&dspi1 {
@@ -99,6 +150,14 @@

&i2c1 {
status = "okay";
+ codec: sgtl5000@a {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <&reg_3p3v>;
+ VDDIO-supply = <&reg_3p3v>;
+ clocks = <&sys_mclk 1>;
+ };
};

&ifc {
@@ -138,6 +197,10 @@
};
};

+&sai1 {
+ status = "okay";
+};
+
&uart0 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi
index 6c41b10..4ad30d0 100644
--- a/arch/arm/boot/dts/ls1021a.dtsi
+++ b/arch/arm/boot/dts/ls1021a.dtsi
@@ -345,28 +345,30 @@
};

sai1: sai@2b50000 {
+ #sound-dai-cells = <0>;
compatible = "fsl,vf610-sai";
reg = <0x0 0x2b50000 0x0 0x10000>;
interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&platform_clk 1>;
- clock-names = "sai";
+ clocks = <&platform_clk 1>, <&platform_clk 1>,
+ <&platform_clk 1>, <&platform_clk 1>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
dma-names = "tx", "rx";
dmas = <&edma0 1 47>,
<&edma0 1 46>;
- big-endian;
status = "disabled";
};

sai2: sai@2b60000 {
+ #sound-dai-cells = <0>;
compatible = "fsl,vf610-sai";
reg = <0x0 0x2b60000 0x0 0x10000>;
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&platform_clk 1>;
- clock-names = "sai";
+ clocks = <&platform_clk 1>, <&platform_clk 1>,
+ <&platform_clk 1>, <&platform_clk 1>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
dma-names = "tx", "rx";
dmas = <&edma0 1 45>,
<&edma0 1 44>;
- big-endian;
status = "disabled";
};

--
2.1.0.27.g96db324


2015-07-13 14:19:47

by Shawn Guo

[permalink] [raw]
Subject: Re: [PATCH] dts: ls1021a: audio: Add dts nodes for audio on LS1021A

On Fri, Jul 03, 2015 at 11:58:32AM +0800, Alison Wang wrote:
> This patch adds dts nodes for audio on LS1021A.
>
> Signed-off-by: Alison Wang <[email protected]>
> ---
> arch/arm/boot/dts/ls1021a-qds.dts | 71 +++++++++++++++++++++++++++++++++++++++
> arch/arm/boot/dts/ls1021a-twr.dts | 63 ++++++++++++++++++++++++++++++++++
> arch/arm/boot/dts/ls1021a.dtsi | 14 ++++----
> 3 files changed, 142 insertions(+), 6 deletions(-)
>
> diff --git a/arch/arm/boot/dts/ls1021a-qds.dts b/arch/arm/boot/dts/ls1021a-qds.dts
> index f16a061..9533f1d 100644
> --- a/arch/arm/boot/dts/ls1021a-qds.dts
> +++ b/arch/arm/boot/dts/ls1021a-qds.dts
> @@ -58,6 +58,57 @@
> enet0_sgmii_phy = &sgmii_phy1c;
> enet1_sgmii_phy = &sgmii_phy1d;
> };
> +
> + clocks {
> + sys_mclk: clock {

The generic node name works only when there is a @unit-address after it.
Otherwise, when you have more clocks to add, they will have the same
node name.

But one of the device tree maintainer doesn't like the idea of "clocks"
container at all. So you may just want to put the node directly under
root with a unit node name, something like the following.

sys_mclk: clock-mclk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24576000>;
};

Shawn

> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <24576000>;
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_3p3v: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Headphone", "Headphone Jack",
> + "Speaker", "Speaker Ext",
> + "Line", "Line In Jack";
> + simple-audio-card,routing =
> + "MIC_IN", "Microphone Jack",
> + "Microphone Jack", "Mic Bias",
> + "LINE_IN", "Line In Jack",
> + "Headphone Jack", "HP_OUT",
> + "Speaker Ext", "LINE_OUT";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&sai2>;
> + frame-master;
> + bitclock-master;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&codec>;
> + frame-master;
> + bitclock-master;
> + };
> + };
> };
>
> &dspi0 {
> @@ -99,6 +150,7 @@
> status = "okay";
>
> pca9547: mux@77 {
> + compatible = "nxp,pca9547";
> reg = <0x77>;
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -153,6 +205,21 @@
> reg = <0x4c>;
> };
> };
> +
> + i2c@4 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x4>;
> +
> + codec: sgtl5000@2a {
> + #sound-dai-cells = <0>;
> + compatible = "fsl,sgtl5000";
> + reg = <0x2a>;
> + VDDA-supply = <&reg_3p3v>;
> + VDDIO-supply = <&reg_3p3v>;
> + clocks = <&sys_mclk 1>;
> + };
> + };
> };
> };
>
> @@ -251,6 +318,10 @@
> };
> };
>
> +&sai2 {
> + status = "okay";
> +};
> +
> &uart0 {
> status = "okay";
> };
> diff --git a/arch/arm/boot/dts/ls1021a-twr.dts b/arch/arm/boot/dts/ls1021a-twr.dts
> index 4b61766..a0d9ad6 100644
> --- a/arch/arm/boot/dts/ls1021a-twr.dts
> +++ b/arch/arm/boot/dts/ls1021a-twr.dts
> @@ -56,6 +56,57 @@
> enet0_sgmii_phy = &sgmii_phy2;
> enet1_sgmii_phy = &sgmii_phy0;
> };
> +
> + clocks {
> + sys_mclk: clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <24576000>;
> + };
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_3p3v: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Headphone", "Headphone Jack",
> + "Speaker", "Speaker Ext",
> + "Line", "Line In Jack";
> + simple-audio-card,routing =
> + "MIC_IN", "Microphone Jack",
> + "Microphone Jack", "Mic Bias",
> + "LINE_IN", "Line In Jack",
> + "Headphone Jack", "HP_OUT",
> + "Speaker Ext", "LINE_OUT";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&sai1>;
> + frame-master;
> + bitclock-master;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&codec>;
> + frame-master;
> + bitclock-master;
> + };
> + };
> };
>
> &dspi1 {
> @@ -99,6 +150,14 @@
>
> &i2c1 {
> status = "okay";
> + codec: sgtl5000@a {
> + #sound-dai-cells = <0>;
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + VDDA-supply = <&reg_3p3v>;
> + VDDIO-supply = <&reg_3p3v>;
> + clocks = <&sys_mclk 1>;
> + };
> };
>
> &ifc {
> @@ -138,6 +197,10 @@
> };
> };
>
> +&sai1 {
> + status = "okay";
> +};
> +
> &uart0 {
> status = "okay";
> };
> diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi
> index 6c41b10..4ad30d0 100644
> --- a/arch/arm/boot/dts/ls1021a.dtsi
> +++ b/arch/arm/boot/dts/ls1021a.dtsi
> @@ -345,28 +345,30 @@
> };
>
> sai1: sai@2b50000 {
> + #sound-dai-cells = <0>;
> compatible = "fsl,vf610-sai";
> reg = <0x0 0x2b50000 0x0 0x10000>;
> interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&platform_clk 1>;
> - clock-names = "sai";
> + clocks = <&platform_clk 1>, <&platform_clk 1>,
> + <&platform_clk 1>, <&platform_clk 1>;
> + clock-names = "bus", "mclk1", "mclk2", "mclk3";
> dma-names = "tx", "rx";
> dmas = <&edma0 1 47>,
> <&edma0 1 46>;
> - big-endian;
> status = "disabled";
> };
>
> sai2: sai@2b60000 {
> + #sound-dai-cells = <0>;
> compatible = "fsl,vf610-sai";
> reg = <0x0 0x2b60000 0x0 0x10000>;
> interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&platform_clk 1>;
> - clock-names = "sai";
> + clocks = <&platform_clk 1>, <&platform_clk 1>,
> + <&platform_clk 1>, <&platform_clk 1>;
> + clock-names = "bus", "mclk1", "mclk2", "mclk3";
> dma-names = "tx", "rx";
> dmas = <&edma0 1 45>,
> <&edma0 1 44>;
> - big-endian;
> status = "disabled";
> };
>
> --
> 2.1.0.27.g96db324
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [email protected]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>

2015-07-14 10:09:13

by Huan Wang

[permalink] [raw]
Subject: RE: [PATCH] dts: ls1021a: audio: Add dts nodes for audio on LS1021A

Shawn,

> On Fri, Jul 03, 2015 at 11:58:32AM +0800, Alison Wang wrote:
> > This patch adds dts nodes for audio on LS1021A.
> >
> > Signed-off-by: Alison Wang <[email protected]>
> > ---
> > arch/arm/boot/dts/ls1021a-qds.dts | 71
> > +++++++++++++++++++++++++++++++++++++++
> > arch/arm/boot/dts/ls1021a-twr.dts | 63
> ++++++++++++++++++++++++++++++++++
> > arch/arm/boot/dts/ls1021a.dtsi | 14 ++++----
> > 3 files changed, 142 insertions(+), 6 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/ls1021a-qds.dts
> > b/arch/arm/boot/dts/ls1021a-qds.dts
> > index f16a061..9533f1d 100644
> > --- a/arch/arm/boot/dts/ls1021a-qds.dts
> > +++ b/arch/arm/boot/dts/ls1021a-qds.dts
> > @@ -58,6 +58,57 @@
> > enet0_sgmii_phy = &sgmii_phy1c;
> > enet1_sgmii_phy = &sgmii_phy1d;
> > };
> > +
> > + clocks {
> > + sys_mclk: clock {
>
> The generic node name works only when there is a @unit-address after it.
> Otherwise, when you have more clocks to add, they will have the same
> node name.
>
> But one of the device tree maintainer doesn't like the idea of "clocks"
> container at all. So you may just want to put the node directly under
> root with a unit node name, something like the following.
>
> sys_mclk: clock-mclk {
> compatible = "fixed-clock";
> #clock-cells = <0>;
> clock-frequency = <24576000>;
> };
[Alison Wang] Thanks for your explanation and suggestion.
I will change in v2.
>
> Shawn
>
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <24576000>;
> > + };
> > + };
> > +
> > + regulators {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + reg_3p3v: regulator@0 {
> > + compatible = "regulator-fixed";
> > + reg = <0>;
> > + regulator-name = "3P3V";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > + };
> > +
> > + sound {
> > + compatible = "simple-audio-card";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,widgets =
> > + "Microphone", "Microphone Jack",
> > + "Headphone", "Headphone Jack",
> > + "Speaker", "Speaker Ext",
> > + "Line", "Line In Jack";
> > + simple-audio-card,routing =
> > + "MIC_IN", "Microphone Jack",
> > + "Microphone Jack", "Mic Bias",
> > + "LINE_IN", "Line In Jack",
> > + "Headphone Jack", "HP_OUT",
> > + "Speaker Ext", "LINE_OUT";
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&sai2>;
> > + frame-master;
> > + bitclock-master;
> > + };
> > +
> > + simple-audio-card,codec {
> > + sound-dai = <&codec>;
> > + frame-master;
> > + bitclock-master;
> > + };
> > + };
> > };
> >
> > &dspi0 {
> > @@ -99,6 +150,7 @@
> > status = "okay";
> >
> > pca9547: mux@77 {
> > + compatible = "nxp,pca9547";
> > reg = <0x77>;
> > #address-cells = <1>;
> > #size-cells = <0>;
> > @@ -153,6 +205,21 @@
> > reg = <0x4c>;
> > };
> > };
> > +
> > + i2c@4 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0x4>;
> > +
> > + codec: sgtl5000@2a {
> > + #sound-dai-cells = <0>;
> > + compatible = "fsl,sgtl5000";
> > + reg = <0x2a>;
> > + VDDA-supply = <&reg_3p3v>;
> > + VDDIO-supply = <&reg_3p3v>;
> > + clocks = <&sys_mclk 1>;
> > + };
> > + };
> > };
> > };
> >
> > @@ -251,6 +318,10 @@
> > };
> > };
> >
> > +&sai2 {
> > + status = "okay";
> > +};
> > +
> > &uart0 {
> > status = "okay";
> > };
> > diff --git a/arch/arm/boot/dts/ls1021a-twr.dts
> > b/arch/arm/boot/dts/ls1021a-twr.dts
> > index 4b61766..a0d9ad6 100644
> > --- a/arch/arm/boot/dts/ls1021a-twr.dts
> > +++ b/arch/arm/boot/dts/ls1021a-twr.dts
> > @@ -56,6 +56,57 @@
> > enet0_sgmii_phy = &sgmii_phy2;
> > enet1_sgmii_phy = &sgmii_phy0;
> > };
> > +
> > + clocks {
> > + sys_mclk: clock {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <24576000>;
> > + };
> > + };
> > +
> > + regulators {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + reg_3p3v: regulator@0 {
> > + compatible = "regulator-fixed";
> > + reg = <0>;
> > + regulator-name = "3P3V";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > + };
> > +
> > + sound {
> > + compatible = "simple-audio-card";
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,widgets =
> > + "Microphone", "Microphone Jack",
> > + "Headphone", "Headphone Jack",
> > + "Speaker", "Speaker Ext",
> > + "Line", "Line In Jack";
> > + simple-audio-card,routing =
> > + "MIC_IN", "Microphone Jack",
> > + "Microphone Jack", "Mic Bias",
> > + "LINE_IN", "Line In Jack",
> > + "Headphone Jack", "HP_OUT",
> > + "Speaker Ext", "LINE_OUT";
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&sai1>;
> > + frame-master;
> > + bitclock-master;
> > + };
> > +
> > + simple-audio-card,codec {
> > + sound-dai = <&codec>;
> > + frame-master;
> > + bitclock-master;
> > + };
> > + };
> > };
> >
> > &dspi1 {
> > @@ -99,6 +150,14 @@
> >
> > &i2c1 {
> > status = "okay";
> > + codec: sgtl5000@a {
> > + #sound-dai-cells = <0>;
> > + compatible = "fsl,sgtl5000";
> > + reg = <0x0a>;
> > + VDDA-supply = <&reg_3p3v>;
> > + VDDIO-supply = <&reg_3p3v>;
> > + clocks = <&sys_mclk 1>;
> > + };
> > };
> >
> > &ifc {
> > @@ -138,6 +197,10 @@
> > };
> > };
> >
> > +&sai1 {
> > + status = "okay";
> > +};
> > +
> > &uart0 {
> > status = "okay";
> > };
> > diff --git a/arch/arm/boot/dts/ls1021a.dtsi
> > b/arch/arm/boot/dts/ls1021a.dtsi index 6c41b10..4ad30d0 100644
> > --- a/arch/arm/boot/dts/ls1021a.dtsi
> > +++ b/arch/arm/boot/dts/ls1021a.dtsi
> > @@ -345,28 +345,30 @@
> > };
> >
> > sai1: sai@2b50000 {
> > + #sound-dai-cells = <0>;
> > compatible = "fsl,vf610-sai";
> > reg = <0x0 0x2b50000 0x0 0x10000>;
> > interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
> > - clocks = <&platform_clk 1>;
> > - clock-names = "sai";
> > + clocks = <&platform_clk 1>, <&platform_clk 1>,
> > + <&platform_clk 1>, <&platform_clk 1>;
> > + clock-names = "bus", "mclk1", "mclk2", "mclk3";
> > dma-names = "tx", "rx";
> > dmas = <&edma0 1 47>,
> > <&edma0 1 46>;
> > - big-endian;
> > status = "disabled";
> > };
> >
> > sai2: sai@2b60000 {
> > + #sound-dai-cells = <0>;
> > compatible = "fsl,vf610-sai";
> > reg = <0x0 0x2b60000 0x0 0x10000>;
> > interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> > - clocks = <&platform_clk 1>;
> > - clock-names = "sai";
> > + clocks = <&platform_clk 1>, <&platform_clk 1>,
> > + <&platform_clk 1>, <&platform_clk 1>;
> > + clock-names = "bus", "mclk1", "mclk2", "mclk3";
> > dma-names = "tx", "rx";
> > dmas = <&edma0 1 45>,
> > <&edma0 1 44>;
> > - big-endian;
> > status = "disabled";
> > };
> >
> > --
> > 2.1.0.27.g96db324
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe
> > linux-kernel" in the body of a message to [email protected]
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> > Please read the FAQ at http://www.tux.org/lkml/
> >