In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.
Signed-off-by: Niklas Cassel <[email protected]>
---
.../bindings/serial/axis,etraxfs-uart.txt | 6 +++-
drivers/tty/serial/Kconfig | 1 +
drivers/tty/serial/etraxfs-uart.c | 40 ++++++----------------
3 files changed, 16 insertions(+), 31 deletions(-)
diff --git a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt
index ebcbb62..51b3c9e 100644
--- a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt
+++ b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt
@@ -6,7 +6,7 @@ Required properties:
- interrupts: device interrupt
Optional properties:
-- {dtr,dsr,ri,cd}-gpios: specify a GPIO for DTR/DSR/RI/CD
+- {dtr,dsr,rng,dcd}-gpios: specify a GPIO for DTR/DSR/RI/DCD
line respectively.
Example:
@@ -16,4 +16,8 @@ serial@b00260000 {
reg = <0xb0026000 0x1000>;
interrupts = <68>;
status = "disabled";
+ dtr-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>;
+ dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>;
+ rng-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>;
+ dcd-gpios = <&sysgpio 3 GPIO_ACTIVE_LOW>;
};
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 15b4079..8a4b62e 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1067,6 +1067,7 @@ config SERIAL_ETRAXFS
bool "ETRAX FS serial port support"
depends on ETRAX_ARCH_V32 && OF
select SERIAL_CORE
+ select SERIAL_MCTRL_GPIO if GPIOLIB
config SERIAL_ETRAXFS_CONSOLE
bool "ETRAX FS serial console support"
diff --git a/drivers/tty/serial/etraxfs-uart.c b/drivers/tty/serial/etraxfs-uart.c
index a647605..382d434 100644
--- a/drivers/tty/serial/etraxfs-uart.c
+++ b/drivers/tty/serial/etraxfs-uart.c
@@ -10,6 +10,8 @@
#include <linux/of_address.h>
#include <hwregs/ser_defs.h>
+#include "serial_mctrl_gpio.h"
+
#define DRV_NAME "etraxfs-uart"
#define UART_NR CONFIG_ETRAX_SERIAL_PORTS
@@ -28,10 +30,7 @@ struct uart_cris_port {
void __iomem *regi_ser;
- struct gpio_desc *dtr_pin;
- struct gpio_desc *dsr_pin;
- struct gpio_desc *ri_pin;
- struct gpio_desc *cd_pin;
+ struct mctrl_gpios *gpios;
int write_ongoing;
};
@@ -396,21 +395,9 @@ static unsigned int etraxfs_uart_get_mctrl(struct uart_port *port)
ret = 0;
if (crisv32_serial_get_rts(up))
ret |= TIOCM_RTS;
- /* DTR is active low */
- if (up->dtr_pin && !gpiod_get_raw_value(up->dtr_pin))
- ret |= TIOCM_DTR;
- /* CD is active low */
- if (up->cd_pin && !gpiod_get_raw_value(up->cd_pin))
- ret |= TIOCM_CD;
- /* RI is active low */
- if (up->ri_pin && !gpiod_get_raw_value(up->ri_pin))
- ret |= TIOCM_RI;
- /* DSR is active low */
- if (up->dsr_pin && !gpiod_get_raw_value(up->dsr_pin))
- ret |= TIOCM_DSR;
if (crisv32_serial_get_cts(up))
ret |= TIOCM_CTS;
- return ret;
+ return mctrl_gpio_get(up->gpios, &ret);
}
static void etraxfs_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
@@ -418,15 +405,7 @@ static void etraxfs_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
struct uart_cris_port *up = (struct uart_cris_port *)port;
crisv32_serial_set_rts(up, mctrl & TIOCM_RTS ? 1 : 0, 0);
- /* DTR is active low */
- if (up->dtr_pin)
- gpiod_set_raw_value(up->dtr_pin, mctrl & TIOCM_DTR ? 0 : 1);
- /* RI is active low */
- if (up->ri_pin)
- gpiod_set_raw_value(up->ri_pin, mctrl & TIOCM_RNG ? 0 : 1);
- /* CD is active low */
- if (up->cd_pin)
- gpiod_set_raw_value(up->cd_pin, mctrl & TIOCM_CD ? 0 : 1);
+ mctrl_gpio_set(up->gpios, mctrl);
}
static void etraxfs_uart_break_ctl(struct uart_port *port, int break_state)
@@ -920,11 +899,12 @@ static int etraxfs_uart_probe(struct platform_device *pdev)
up->irq = irq_of_parse_and_map(np, 0);
up->regi_ser = of_iomap(np, 0);
- up->dtr_pin = devm_gpiod_get_optional(&pdev->dev, "dtr");
- up->dsr_pin = devm_gpiod_get_optional(&pdev->dev, "dsr");
- up->ri_pin = devm_gpiod_get_optional(&pdev->dev, "ri");
- up->cd_pin = devm_gpiod_get_optional(&pdev->dev, "cd");
up->port.dev = &pdev->dev;
+
+ up->gpios = mctrl_gpio_init(&pdev->dev, 0);
+ if (IS_ERR(up->gpios))
+ return PTR_ERR(up->gpios);
+
cris_serial_port_init(&up->port, dev_id);
etraxfs_uart_ports[dev_id] = up;
--
2.4.6
On Sat, Jul 25, 2015 at 2:02 AM, Niklas Cassel <[email protected]> wrote:
> In order to use the mctrl_gpio helpers, we change the DT bindings:
> ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
> However, no in-tree dts/dtsi specifies these, so no worries.
>
> Signed-off-by: Niklas Cassel <[email protected]>
Acked-by: Linus Walleij <[email protected]>
Yours,
Linus Walleij
On Sat, Jul 25, 2015 at 02:02:46AM +0200, Niklas Cassel wrote:
> In order to use the mctrl_gpio helpers, we change the DT bindings:
> ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
> However, no in-tree dts/dtsi specifies these, so no worries.
>
> Signed-off-by: Niklas Cassel <[email protected]>
Acked-by: Guenter Roeck <[email protected]>
Tested-by: Guenter Roeck <[email protected]>
Any chance to get this into -next ? The problem it fixes
still causes my crisv32 qemu tests to fail.