This series adds support for hisilicon stub clock driver. On hi6220,
the bootloader needs load the firmware image and set info for OPPs;
after run into kernel, the stub clock driver is used to communicate
w/t firmware for cpu dynamic frequency scaling.
In patch series v1/v2, the stub clock driver simply writes request in
sram and send ipc to firmware; For patch series v3, the firmware has
been upgraded to use mailbox, so stub clock driver will call standard
mailbox APIs to request mailbox channel and send message to firmware.
Patch 4 adds stub clock node into dts and it references mailbox with
phandle, so patch 4 will depend on mailbox driver's patch series [1].
These patches have been tested on 96board hikey and is used by cpufreq
driver.
Changes from v3:
* Patch "clk: hisi: refine parameter checking for init" [2] has been
applied to clk-next, so skip it in v4
* According to Stephen Boyd's review, fix and refine stub clock driver
* The stub clock driver depends on mailbox channel's initialization, so
mailbox init firstly with core_initcall() and use subsys_initcall()
for stub clock driver
Changes from v2:
* Use platform_device's probe for clock's initialization
* Use mailbox channel for clock frequency change
Changes from v1:
* Refine parameter checking for init flow
* Remove unnecessary debugging info
* Modify to check spinlock pointer when register clocks
[1] http://archive.arm.linux.org.uk/lurker/message/20150803.011307.1062b247.en.html
[2] http://archive.arm.linux.org.uk/lurker/message/20150803.011334.4b6f2fc7.en.html
Leo Yan (4):
dt-bindings: arm: Hi6220: add doc for SRAM controller
dt-bindings: clk: Hi6220: Document stub clock driver
clk: Hi6220: add stub clock driver
arm64: dts: add Hi6220's stub clock node
.../bindings/arm/hisilicon/hisilicon.txt | 18 ++
.../devicetree/bindings/clock/hi6220-clock.txt | 19 +-
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 23 ++
drivers/clk/hisilicon/Kconfig | 2 +-
drivers/clk/hisilicon/Makefile | 2 +-
drivers/clk/hisilicon/clk-hi6220-stub.c | 276 +++++++++++++++++++++
6 files changed, 337 insertions(+), 3 deletions(-)
create mode 100644 drivers/clk/hisilicon/clk-hi6220-stub.c
--
1.9.1
Document "hisilicon,hi6220-sramctrl" for SRAM controller.
Signed-off-by: Leo Yan <[email protected]>
---
.../devicetree/bindings/arm/hisilicon/hisilicon.txt | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
index c431c67..c733e28 100644
--- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
@@ -127,6 +127,24 @@ Example:
#clock-cells = <1>;
};
+
+Hisilicon Hi6220 SRAM controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-sramctrl", "syscon"
+- reg : Register address and size
+
+Hisilicon's SoCs use sram for multiple purpose; on Hi6220 there have several
+SRAM banks for power management, modem, security, etc. Further, use "syscon"
+managing the common sram which can be shared by multiple modules.
+
+Example:
+ /*for Hi6220*/
+ sram: sram@fff80000 {
+ compatible = "hisilicon,hi6220-sramctrl", "syscon";
+ reg = <0x0 0xfff80000 0x0 0x12000>;
+ };
+
-----------------------------------------------------------------------
Hisilicon HiP01 system controller
--
1.9.1
Document the new compatible for stub clock driver which is used for CPU
and DDR's dynamic frequency scaling.
Signed-off-by: Leo Yan <[email protected]>
---
.../devicetree/bindings/clock/hi6220-clock.txt | 19 ++++++++++++++++++-
1 file changed, 18 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/clock/hi6220-clock.txt b/Documentation/devicetree/bindings/clock/hi6220-clock.txt
index 259e30a..e4d5fea 100644
--- a/Documentation/devicetree/bindings/clock/hi6220-clock.txt
+++ b/Documentation/devicetree/bindings/clock/hi6220-clock.txt
@@ -15,19 +15,36 @@ Required Properties:
- "hisilicon,hi6220-sysctrl"
- "hisilicon,hi6220-mediactrl"
- "hisilicon,hi6220-pmctrl"
+ - "hisilicon,hi6220-stub-clk"
- reg: physical base address of the controller and length of memory mapped
region.
- #clock-cells: should be 1.
-For example:
+Optional Properties:
+
+- hisilicon,hi6220-clk-sram: phandle to the syscon managing the SoC internal sram;
+ the driver need use the sram to pass parameters for frequency change.
+
+- mboxes: use the label reference for the mailbox as the first parameter, the
+ second parameter is the channel number.
+
+Example 1:
sys_ctrl: sys_ctrl@f7030000 {
compatible = "hisilicon,hi6220-sysctrl", "syscon";
reg = <0x0 0xf7030000 0x0 0x2000>;
#clock-cells = <1>;
};
+Example 2:
+ stub_clock: stub_clock {
+ compatible = "hisilicon,hi6220-stub-clk";
+ hisilicon,hi6220-clk-sram = <&sram>;
+ #clock-cells = <1>;
+ mboxes = <&mailbox 1>;
+ };
+
Each clock is assigned an identifier and client nodes use this identifier
to specify the clock which they consume.
--
1.9.1
On Hi6220, there have some clocks which can use mailbox channel to send
messages to power controller to change frequency; this includes CPU, GPU
and DDR clocks.
For dynamic frequency scaling, firstly need write the frequency value to
SRAM region, and then send message to mailbox to trigger power controller
to handle this requirement. This driver will use syscon APIs to pass SRAM
memory region and use common mailbox APIs for channels accessing.
This init driver will support cpu frequency change firstly.
Signed-off-by: Leo Yan <[email protected]>
---
drivers/clk/hisilicon/Kconfig | 2 +-
drivers/clk/hisilicon/Makefile | 2 +-
drivers/clk/hisilicon/clk-hi6220-stub.c | 276 ++++++++++++++++++++++++++++++++
3 files changed, 278 insertions(+), 2 deletions(-)
create mode 100644 drivers/clk/hisilicon/clk-hi6220-stub.c
diff --git a/drivers/clk/hisilicon/Kconfig b/drivers/clk/hisilicon/Kconfig
index b4165ba..2c16807 100644
--- a/drivers/clk/hisilicon/Kconfig
+++ b/drivers/clk/hisilicon/Kconfig
@@ -1,6 +1,6 @@
config COMMON_CLK_HI6220
bool "Hi6220 Clock Driver"
- depends on ARCH_HISI || COMPILE_TEST
+ depends on (ARCH_HISI || COMPILE_TEST) && MAILBOX
default ARCH_HISI
help
Build the Hisilicon Hi6220 clock driver based on the common clock framework.
diff --git a/drivers/clk/hisilicon/Makefile b/drivers/clk/hisilicon/Makefile
index 48f0116..4a1001a 100644
--- a/drivers/clk/hisilicon/Makefile
+++ b/drivers/clk/hisilicon/Makefile
@@ -7,4 +7,4 @@ obj-y += clk.o clkgate-separated.o clkdivider-hi6220.o
obj-$(CONFIG_ARCH_HI3xxx) += clk-hi3620.o
obj-$(CONFIG_ARCH_HIP04) += clk-hip04.o
obj-$(CONFIG_ARCH_HIX5HD2) += clk-hix5hd2.o
-obj-$(CONFIG_COMMON_CLK_HI6220) += clk-hi6220.o
+obj-$(CONFIG_COMMON_CLK_HI6220) += clk-hi6220.o clk-hi6220-stub.o
diff --git a/drivers/clk/hisilicon/clk-hi6220-stub.c b/drivers/clk/hisilicon/clk-hi6220-stub.c
new file mode 100644
index 0000000..9337d43
--- /dev/null
+++ b/drivers/clk/hisilicon/clk-hi6220-stub.c
@@ -0,0 +1,276 @@
+/*
+ * Hi6220 stub clock driver
+ *
+ * Copyright (c) 2015 Hisilicon Limited.
+ * Copyright (c) 2015 Linaro Limited.
+ *
+ * Author: Leo Yan <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mailbox_client.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+
+/* Stub clocks id */
+#define HI6220_STUB_ACPU0 0
+#define HI6220_STUB_ACPU1 1
+#define HI6220_STUB_GPU 2
+#define HI6220_STUB_DDR 5
+
+/* Mailbox message */
+#define HI6220_MBOX_MSG_LEN 8
+
+#define HI6220_MBOX_FREQ 0xA
+#define HI6220_MBOX_CMD_SET 0x3
+#define HI6220_MBOX_OBJ_AP 0x0
+
+/* CPU dynamic frequency scaling */
+#define ACPU_DFS_FREQ_MAX 0x1724
+#define ACPU_DFS_CUR_FREQ 0x17CC
+#define ACPU_DFS_FLAG 0x1B30
+#define ACPU_DFS_FREQ_REQ 0x1B34
+#define ACPU_DFS_FREQ_LMT 0x1B38
+#define ACPU_DFS_LOCK_FLAG 0xAEAEAEAE
+
+#define to_stub_clk(hw) container_of(hw, struct hi6220_stub_clk, hw)
+
+struct hi6220_stub_clk {
+ u32 id;
+
+ struct device *dev;
+ struct clk_hw hw;
+
+ struct regmap *dfs_map;
+ struct mbox_client cl;
+ struct mbox_chan *mbox;
+};
+
+struct hi6220_mbox_msg {
+ unsigned char type;
+ unsigned char cmd;
+ unsigned char obj;
+ unsigned char src;
+ unsigned char para[4];
+};
+
+union hi6220_mbox_data {
+ unsigned int data[HI6220_MBOX_MSG_LEN];
+ struct hi6220_mbox_msg msg;
+};
+
+static unsigned int hi6220_acpu_get_freq(struct hi6220_stub_clk *stub_clk)
+{
+ unsigned int freq;
+
+ regmap_read(stub_clk->dfs_map, ACPU_DFS_CUR_FREQ, &freq);
+ return freq;
+}
+
+static int hi6220_acpu_set_freq(struct hi6220_stub_clk *stub_clk,
+ unsigned int freq)
+{
+ union hi6220_mbox_data data;
+
+ /* set the frequency in sram */
+ regmap_write(stub_clk->dfs_map, ACPU_DFS_FREQ_REQ, freq);
+
+ /* compound mailbox message */
+ data.msg.type = HI6220_MBOX_FREQ;
+ data.msg.cmd = HI6220_MBOX_CMD_SET;
+ data.msg.obj = HI6220_MBOX_OBJ_AP;
+ data.msg.src = HI6220_MBOX_OBJ_AP;
+
+ mbox_send_message(stub_clk->mbox, &data);
+ return 0;
+}
+
+static int hi6220_acpu_round_freq(struct hi6220_stub_clk *stub_clk,
+ unsigned int freq)
+{
+ unsigned int limit_flag, limit_freq = UINT_MAX;
+ unsigned int max_freq;
+
+ /* check the constrained frequency */
+ regmap_read(stub_clk->dfs_map, ACPU_DFS_FLAG, &limit_flag);
+ if (limit_flag == ACPU_DFS_LOCK_FLAG)
+ regmap_read(stub_clk->dfs_map, ACPU_DFS_FREQ_LMT, &limit_freq);
+
+ /* check the supported maximum frequency */
+ regmap_read(stub_clk->dfs_map, ACPU_DFS_FREQ_MAX, &max_freq);
+
+ /* calculate the real maximum frequency */
+ max_freq = min(max_freq, limit_freq);
+
+ if (WARN_ON(freq > max_freq))
+ freq = max_freq;
+
+ return freq;
+}
+
+static unsigned long hi6220_stub_clk_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ u32 rate = 0;
+ struct hi6220_stub_clk *stub_clk = to_stub_clk(hw);
+
+ switch (stub_clk->id) {
+ case HI6220_STUB_ACPU0:
+ rate = hi6220_acpu_get_freq(stub_clk);
+
+ /* convert from kHz to Hz */
+ rate *= 1000;
+ break;
+
+ default:
+ dev_err(stub_clk->dev, "%s: un-supported clock id %d\n",
+ __func__, stub_clk->id);
+ break;
+ }
+
+ return rate;
+}
+
+static int hi6220_stub_clk_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct hi6220_stub_clk *stub_clk = to_stub_clk(hw);
+ unsigned long new_rate = rate / 1000; /* kHz */
+ int ret = 0;
+
+ switch (stub_clk->id) {
+ case HI6220_STUB_ACPU0:
+ ret = hi6220_acpu_set_freq(stub_clk, new_rate);
+ if (ret < 0)
+ return ret;
+
+ break;
+
+ default:
+ dev_err(stub_clk->dev, "%s: un-supported clock id %d\n",
+ __func__, stub_clk->id);
+ break;
+ }
+
+ pr_debug("%s: set rate=%ldkHz\n", __func__, new_rate);
+ return ret;
+}
+
+static long hi6220_stub_clk_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ struct hi6220_stub_clk *stub_clk = to_stub_clk(hw);
+ unsigned long new_rate = rate / 1000; /* kHz */
+
+ switch (stub_clk->id) {
+ case HI6220_STUB_ACPU0:
+ new_rate = hi6220_acpu_round_freq(stub_clk, new_rate);
+
+ /* convert from kHz to Hz */
+ new_rate *= 1000;
+ break;
+
+ default:
+ dev_err(stub_clk->dev, "%s: un-supported clock id %d\n",
+ __func__, stub_clk->id);
+ break;
+ }
+
+ return new_rate;
+}
+
+static const struct clk_ops hi6220_stub_clk_ops = {
+ .recalc_rate = hi6220_stub_clk_recalc_rate,
+ .round_rate = hi6220_stub_clk_round_rate,
+ .set_rate = hi6220_stub_clk_set_rate,
+};
+
+static int hi6220_stub_clk_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct clk_init_data init;
+ struct hi6220_stub_clk *stub_clk;
+ struct clk *clk;
+ struct device_node *np = pdev->dev.of_node;
+ int ret;
+
+ stub_clk = devm_kzalloc(dev, sizeof(*stub_clk), GFP_KERNEL);
+ if (!stub_clk)
+ return -ENOMEM;
+
+ stub_clk->dfs_map = syscon_regmap_lookup_by_phandle(np,
+ "hisilicon,hi6220-clk-sram");
+ if (IS_ERR(stub_clk->dfs_map)) {
+ dev_err(dev, "failed to get sram regmap\n");
+ return PTR_ERR(stub_clk->dfs_map);
+ }
+
+ stub_clk->hw.init = &init;
+ stub_clk->dev = dev;
+ stub_clk->id = HI6220_STUB_ACPU0;
+
+ /* Use mailbox client with blocking mode */
+ stub_clk->cl.dev = dev;
+ stub_clk->cl.tx_done = NULL;
+ stub_clk->cl.tx_block = true;
+ stub_clk->cl.tx_tout = 500;
+ stub_clk->cl.knows_txdone = false;
+
+ /* Allocate mailbox channel */
+ stub_clk->mbox = mbox_request_channel(&stub_clk->cl, 0);
+ if (IS_ERR(stub_clk->mbox)) {
+ dev_err(dev, "failed get mailbox channel\n");
+ return PTR_ERR(stub_clk->mbox);
+ };
+
+ init.name = "acpu0";
+ init.ops = &hi6220_stub_clk_ops;
+ init.num_parents = 0;
+ init.flags = CLK_IS_ROOT;
+
+ clk = devm_clk_register(dev, &stub_clk->hw);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ ret = of_clk_add_provider(np, of_clk_src_simple_get, clk);
+ if (ret) {
+ dev_err(dev, "failed to register OF clock provider\n");
+ return ret;
+ }
+
+ /* initialize buffer to zero */
+ regmap_write(stub_clk->dfs_map, ACPU_DFS_FLAG, 0x0);
+ regmap_write(stub_clk->dfs_map, ACPU_DFS_FREQ_REQ, 0x0);
+ regmap_write(stub_clk->dfs_map, ACPU_DFS_FREQ_LMT, 0x0);
+
+ dev_dbg(dev, "Registered clock '%s'\n", init.name);
+ return 0;
+}
+
+static const struct of_device_id hi6220_stub_clk_of_match[] = {
+ { .compatible = "hisilicon,hi6220-stub-clk", },
+ {}
+};
+
+static struct platform_driver hi6220_stub_clk_driver = {
+ .driver = {
+ .name = "hi6220-stub-clk",
+ .of_match_table = hi6220_stub_clk_of_match,
+ },
+ .probe = hi6220_stub_clk_probe,
+};
+
+static int __init hi6220_stub_clk_init(void)
+{
+ return platform_driver_register(&hi6220_stub_clk_driver);
+}
+subsys_initcall(hi6220_stub_clk_init);
--
1.9.1
Enable SRAM node and stub clock node for Hi6220; furthermore
add the CPU's clock so it will be used by cpufreq-dt driver.
Signed-off-by: Leo Yan <[email protected]>
---
arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index b42a9b7..94b8310 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -57,6 +57,17 @@
device_type = "cpu";
reg = <0x0 0x0>;
enable-method = "psci";
+ clocks = <&stub_clock 0>;
+ clock-latency = <0>;
+ operating-points = <
+ /* kHz */
+ 1200000 0
+ 960000 0
+ 729000 0
+ 432000 0
+ 208000 0
+ >;
+ #cooling-cells = <2>; /* min followed by max */
};
cpu1: cpu@1 {
@@ -136,6 +147,11 @@
#size-cells = <2>;
ranges;
+ sram: sram@fff80000 {
+ compatible = "hisilicon,hi6220-sramctrl", "syscon";
+ reg = <0x0 0xfff80000 0x0 0x12000>;
+ };
+
ao_ctrl: ao_ctrl@f7800000 {
compatible = "hisilicon,hi6220-aoctrl", "syscon";
reg = <0x0 0xf7800000 0x0 0x2000>;
@@ -160,6 +176,13 @@
#clock-cells = <1>;
};
+ stub_clock: stub_clock {
+ compatible = "hisilicon,hi6220-stub-clk";
+ hisilicon,hi6220-clk-sram = <&sram>;
+ #clock-cells = <1>;
+ mboxes = <&mailbox 1>;
+ };
+
uart0: uart@f8015000 { /* console */
compatible = "arm,pl011", "arm,primecell";
reg = <0x0 0xf8015000 0x0 0x1000>;
--
1.9.1
On 08/04, Leo Yan wrote:
> This series adds support for hisilicon stub clock driver. On hi6220,
> the bootloader needs load the firmware image and set info for OPPs;
> after run into kernel, the stub clock driver is used to communicate
> w/t firmware for cpu dynamic frequency scaling.
>
> In patch series v1/v2, the stub clock driver simply writes request in
> sram and send ipc to firmware; For patch series v3, the firmware has
> been upgraded to use mailbox, so stub clock driver will call standard
> mailbox APIs to request mailbox channel and send message to firmware.
>
> Patch 4 adds stub clock node into dts and it references mailbox with
> phandle, so patch 4 will depend on mailbox driver's patch series [1].
> These patches have been tested on 96board hikey and is used by cpufreq
> driver.
The To: list is everyone, so I'm not sure who is supposed to
apply these patches. I'd like to take patches 1, 2, and 3 through
the clk tree though.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
Hi Stephen,
On Tue, Aug 11, 2015 at 05:38:17PM -0700, Stephen Boyd wrote:
> On 08/04, Leo Yan wrote:
> > This series adds support for hisilicon stub clock driver. On hi6220,
> > the bootloader needs load the firmware image and set info for OPPs;
> > after run into kernel, the stub clock driver is used to communicate
> > w/t firmware for cpu dynamic frequency scaling.
> >
> > In patch series v1/v2, the stub clock driver simply writes request in
> > sram and send ipc to firmware; For patch series v3, the firmware has
> > been upgraded to use mailbox, so stub clock driver will call standard
> > mailbox APIs to request mailbox channel and send message to firmware.
> >
> > Patch 4 adds stub clock node into dts and it references mailbox with
> > phandle, so patch 4 will depend on mailbox driver's patch series [1].
> > These patches have been tested on 96board hikey and is used by cpufreq
> > driver.
>
> The To: list is everyone, so I'm not sure who is supposed to
> apply these patches. I'd like to take patches 1, 2, and 3 through
> the clk tree though.
Thanks, you could take first three patches. For patch 4, i will
re-send it after mailbox driver's patches have been merged.
Wei Xu, is this okay for you?
Thanks,
Leo Yan
On 08/04, Leo Yan wrote:
> Document "hisilicon,hi6220-sramctrl" for SRAM controller.
>
> Signed-off-by: Leo Yan <[email protected]>
> ---
Applied to clk-next
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
On 08/04, Leo Yan wrote:
> Document the new compatible for stub clock driver which is used for CPU
> and DDR's dynamic frequency scaling.
>
> Signed-off-by: Leo Yan <[email protected]>
> ---
Applied to clk-next
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
On 08/04, Leo Yan wrote:
> On Hi6220, there have some clocks which can use mailbox channel to send
> messages to power controller to change frequency; this includes CPU, GPU
> and DDR clocks.
>
> For dynamic frequency scaling, firstly need write the frequency value to
> SRAM region, and then send message to mailbox to trigger power controller
> to handle this requirement. This driver will use syscon APIs to pass SRAM
> memory region and use common mailbox APIs for channels accessing.
>
> This init driver will support cpu frequency change firstly.
>
> Signed-off-by: Leo Yan <[email protected]>
> ---
Applied to clk-next
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
On 8/12/2015 2:49 AM, Leo Yan wrote:
> Hi Stephen,
>
> On Tue, Aug 11, 2015 at 05:38:17PM -0700, Stephen Boyd wrote:
>> On 08/04, Leo Yan wrote:
>>> This series adds support for hisilicon stub clock driver. On hi6220,
>>> the bootloader needs load the firmware image and set info for OPPs;
>>> after run into kernel, the stub clock driver is used to communicate
>>> w/t firmware for cpu dynamic frequency scaling.
>>>
>>> In patch series v1/v2, the stub clock driver simply writes request in
>>> sram and send ipc to firmware; For patch series v3, the firmware has
>>> been upgraded to use mailbox, so stub clock driver will call standard
>>> mailbox APIs to request mailbox channel and send message to firmware.
>>>
>>> Patch 4 adds stub clock node into dts and it references mailbox with
>>> phandle, so patch 4 will depend on mailbox driver's patch series [1].
>>> These patches have been tested on 96board hikey and is used by cpufreq
>>> driver.
>>
>> The To: list is everyone, so I'm not sure who is supposed to
>> apply these patches. I'd like to take patches 1, 2, and 3 through
>> the clk tree though.
>
> Thanks, you could take first three patches. For patch 4, i will
> re-send it after mailbox driver's patches have been merged.
Hi Leo,
> Wei Xu, is this okay for you?
OK :)
Best Regards,
Wei
>
> Thanks,
> Leo Yan
>
> .
>