Fix RS232/485 mode incorrect setting after S3/S4 resume for F81504/508/512
We had add RS232/485 RTS control with fecf27a373f5. But when it
resume from S3/S4, the mode register 0x40 + 0x08 * idx + 7 will
rewrite to 0x01 (RS232 mode).
This patch will modify 2 sections.
One is pci_fintek_init(), if it called when first init, it will
write mode register with 0x01. If it called from S3/S4 resume,
it's will get the relative port data and pass it to
pci_fintek_rs485_config() with NULL rs485 parameter.
The another modification is in pci_fintek_rs485_config(). It'll
re-apply old configuration when the parameter rs485 is NULL.
Signed-off-by: Peter Hung <[email protected]>
---
drivers/tty/serial/8250/8250_pci.c | 25 +++++++++++++++++++++----
1 file changed, 21 insertions(+), 4 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index e12e911..68042dd 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1705,7 +1705,9 @@ static int pci_fintek_rs485_config(struct uart_port *port,
pci_read_config_byte(pci_dev, 0x40 + 8 * *index + 7, &setting);
- if (rs485->flags & SER_RS485_ENABLED)
+ if (!rs485)
+ rs485 = &port->rs485;
+ else if (rs485->flags & SER_RS485_ENABLED)
memset(rs485->padding, 0, sizeof(rs485->padding));
else
memset(rs485, 0, sizeof(*rs485));
@@ -1733,7 +1735,10 @@ static int pci_fintek_rs485_config(struct uart_port *port,
}
pci_write_config_byte(pci_dev, 0x40 + 8 * *index + 7, setting);
- port->rs485 = *rs485;
+
+ if (rs485 != &port->rs485)
+ port->rs485 = *rs485;
+
return 0;
}
@@ -1774,6 +1779,8 @@ static int pci_fintek_init(struct pci_dev *dev)
u32 max_port, i;
u32 bar_data[3];
u8 config_base;
+ struct serial_private *priv = pci_get_drvdata(dev);
+ struct uart_8250_port *port;
switch (dev->device) {
case 0x1104: /* 4 ports */
@@ -1815,8 +1822,18 @@ static int pci_fintek_init(struct pci_dev *dev)
pci_write_config_byte(dev, config_base + 0x06, dev->irq);
- /* force init to RS232 Mode */
- pci_write_config_byte(dev, config_base + 0x07, 0x01);
+ if (priv) {
+ /* re-apply RS232/485 mode when
+ * pciserial_resume_ports()
+ */
+ port = serial8250_get_port(priv->line[i]);
+ pci_fintek_rs485_config(&port->port, NULL);
+ } else {
+ /* First init without port data
+ * force init to RS232 Mode
+ */
+ pci_write_config_byte(dev, config_base + 0x07, 0x01);
+ }
}
return max_port;
--
1.9.1