The rk3288 MIPI DSI is a Synopsys DesignWare MIPI DSI host controller
IP. This series adds support for a Synopsys DesignWare MIPI DSI host
controller DRM bridge driver and a rockchip MIPI DSI specific DRM
driver.
This series also includes a DRM panel driver for BOE TV080WUM-NL0 panel.
This panel only use the MIPI DSI video mode.
The MIPI DSI feature is tested on rk3288 evb board, backport them to
chrome os kernel v3.14, and it can display normally.
This patchset is base on the patchset from [email protected].
<http://www.spinics.net/lists/dri-devel/msg77181.html>
Changes in v5:
- change the mipidsi clk to SCLK_MIPIDSI_24M
- modify the mipidsi clk name to SCLK_MIPIDSI_24M
Adviced by Thierry
- use hyphens instead of underscore
- use encoder in drm_bridge
- reformatting the dptdin table
- use readx_poll_timeout to check register
- use msleep to wait
- add a comment to explain how to program phy
- change the program code to symbolic names
- check this for validity of find_panel and clk_prepare_enable
- eliminate the configuration clock
- some optimization for coding style
- modify the clk name to SCLK_MIPIDSI_24M
- add a blank line befor lcd_en
Changes in v4:
- use clk_round_rate to check the clock rate in vop_crtc_mode_fixup
- remove the cfg clk
- remove gpr property from example, since it is noused now.
- add the description about ports
- eliminate some warnning
Changes in v3:
- move the dw_mipi_dsi.txt to Documentation/devicetree/bindings/display/bridge
- move dw_mipi_dsi_rockchip.txt to bindings/display/rockchip/
Changes in v2:
- add the mipi clk id in a single patch
Chris Zhong (9):
clk: rockchip: add id for mipidsi sclk on rk3288
clk: rockchip: add mipidsi clocks on rk3288
drm/rockchip: return a true clock rate to adjusted_mode
drm: bridge: allow some funcs to be optional
drm/bridge: Add Synopsys DesignWare MIPI DSI host controller driver
drm: rockchip: Support Synopsys DesignWare MIPI DSI host controller
Documentation: dt-bindings: Add bindings for rk3288 DW MIPI DSI driver
ARM: dts: rockchip: add rk3288 mipi_dsi nodes
ARM: dts: rockchip: add support mipi panel tv080wum-nl0 for rk3288-evb
Liu Ying (2):
drm/dsi: Add a helper to get bits per pixel of MIPI DSI pixel format
Documentation: dt-bindings: Add bindings for DW MIPI DSI
.../bindings/display/bridge/dw_mipi_dsi.txt | 74 ++
.../display/rockchip/dw_mipi_dsi_rockchip.txt | 56 +
arch/arm/boot/dts/rk3288-evb.dtsi | 20 +-
arch/arm/boot/dts/rk3288.dtsi | 39 +
drivers/clk/rockchip/clk-rk3288.c | 2 +-
drivers/gpu/drm/bridge/Kconfig | 10 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/dw-mipi-dsi.c | 1084 ++++++++++++++++++++
drivers/gpu/drm/drm_bridge.c | 6 +-
drivers/gpu/drm/rockchip/Kconfig | 10 +
drivers/gpu/drm/rockchip/Makefile | 1 +
drivers/gpu/drm/rockchip/dw_mipi_dsi_rockchip.c | 249 +++++
drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 8 +
include/drm/bridge/dw_mipi_dsi.h | 28 +
include/drm/drm_mipi_dsi.h | 14 +
include/dt-bindings/clock/rk3288-cru.h | 1 +
16 files changed, 1599 insertions(+), 4 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt
create mode 100644 Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
create mode 100644 drivers/gpu/drm/bridge/dw-mipi-dsi.c
create mode 100644 drivers/gpu/drm/rockchip/dw_mipi_dsi_rockchip.c
create mode 100644 include/drm/bridge/dw_mipi_dsi.h
--
2.6.3
Adds a new id for the sclk supplying the mipidsi on rk3288 socs.
Signed-off-by: Chris Zhong <[email protected]>
---
Changes in v5:
- change the mipidsi clk to SCLK_MIPIDSI_24M
Changes in v4: None
Changes in v3: None
Changes in v2:
- add the mipi clk id in a single patch
include/dt-bindings/clock/rk3288-cru.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/include/dt-bindings/clock/rk3288-cru.h b/include/dt-bindings/clock/rk3288-cru.h
index c719aac..14c759c 100644
--- a/include/dt-bindings/clock/rk3288-cru.h
+++ b/include/dt-bindings/clock/rk3288-cru.h
@@ -86,6 +86,7 @@
#define SCLK_USBPHY480M_SRC 122
#define SCLK_PVTM_CORE 123
#define SCLK_PVTM_GPU 124
+#define SCLK_MIPIDSI_24M 125
#define SCLK_MAC 151
#define SCLK_MACREF_OUT 152
--
2.6.3
sclk_mipidsi_24m is the gating of mipi dsi phy.
Signed-off-by: Chris Zhong <[email protected]>
Acked-by: Stephen Boyd <[email protected]>
---
Changes in v5:
- modify the mipidsi clk name to SCLK_MIPIDSI_24M
Changes in v4: None
Changes in v3: None
Changes in v2: None
drivers/clk/rockchip/clk-rk3288.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/clk/rockchip/clk-rk3288.c b/drivers/clk/rockchip/clk-rk3288.c
index 9040878..bee96e7 100644
--- a/drivers/clk/rockchip/clk-rk3288.c
+++ b/drivers/clk/rockchip/clk-rk3288.c
@@ -709,7 +709,7 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
GATE(SCLK_LCDC_PWM1, "sclk_lcdc_pwm1", "xin24m", 0, RK3288_CLKGATE_CON(13), 11, GFLAGS),
GATE(SCLK_PVTM_CORE, "sclk_pvtm_core", "xin24m", 0, RK3288_CLKGATE_CON(5), 9, GFLAGS),
GATE(SCLK_PVTM_GPU, "sclk_pvtm_gpu", "xin24m", 0, RK3288_CLKGATE_CON(5), 10, GFLAGS),
- GATE(0, "sclk_mipidsi_24m", "xin24m", 0, RK3288_CLKGATE_CON(5), 15, GFLAGS),
+ GATE(SCLK_MIPIDSI_24M, "sclk_mipidsi_24m", "xin24m", 0, RK3288_CLKGATE_CON(5), 15, GFLAGS),
/* sclk_gpu gates */
GATE(ACLK_GPU, "aclk_gpu", "sclk_gpu", 0, RK3288_CLKGATE_CON(18), 0, GFLAGS),
--
2.6.3
Since the mipi dsi driver need to use the clock of vop to make the
calculation of Blanking. But sometimes the clock driver can not set a
accurate clock_rate for vop, get it by clk_round_rate before mode_set,
so we can get the true value.
Signed-off-by: Chris Zhong <[email protected]>
Acked-by: Mark Yao <[email protected]>
---
Changes in v5: None
Changes in v4:
- use clk_round_rate to check the clock rate in vop_crtc_mode_fixup
Changes in v3: None
Changes in v2: None
drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index 5d8ae5e..eff545b 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -1136,9 +1136,14 @@ static bool vop_crtc_mode_fixup(struct drm_crtc *crtc,
const struct drm_display_mode *mode,
struct drm_display_mode *adjusted_mode)
{
+ struct vop *vop = to_vop(crtc);
+
if (adjusted_mode->htotal == 0 || adjusted_mode->vtotal == 0)
return false;
+ adjusted_mode->clock =
+ clk_round_rate(vop->dclk, mode->clock * 1000) / 1000;
+
return true;
}
--
2.6.3
From: Liu Ying <[email protected]>
Signed-off-by: Liu Ying <[email protected]>
Acked-by: Thierry Reding <[email protected]>
Signed-off-by: Chris Zhong <[email protected]>
---
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
include/drm/drm_mipi_dsi.h | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/include/drm/drm_mipi_dsi.h b/include/drm/drm_mipi_dsi.h
index f1d8d0d..3662021 100644
--- a/include/drm/drm_mipi_dsi.h
+++ b/include/drm/drm_mipi_dsi.h
@@ -163,6 +163,20 @@ static inline struct mipi_dsi_device *to_mipi_dsi_device(struct device *dev)
return container_of(dev, struct mipi_dsi_device, dev);
}
+static inline int mipi_dsi_pixel_format_to_bpp(enum mipi_dsi_pixel_format fmt)
+{
+ switch (fmt) {
+ case MIPI_DSI_FMT_RGB888:
+ case MIPI_DSI_FMT_RGB666:
+ return 24;
+ case MIPI_DSI_FMT_RGB666_PACKED:
+ return 18;
+ case MIPI_DSI_FMT_RGB565:
+ return 16;
+ }
+ return -EINVAL;
+}
+
struct mipi_dsi_device *of_find_mipi_dsi_device_by_node(struct device_node *np);
int mipi_dsi_attach(struct mipi_dsi_device *dsi);
int mipi_dsi_detach(struct mipi_dsi_device *dsi);
--
2.6.3
Check the validity of post_disable/pre_enable in bridge->funcs before
call them.
Signed-off-by: Chris Zhong <[email protected]>
---
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
drivers/gpu/drm/drm_bridge.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/drm_bridge.c b/drivers/gpu/drm/drm_bridge.c
index 6b8f721..8f29330 100644
--- a/drivers/gpu/drm/drm_bridge.c
+++ b/drivers/gpu/drm/drm_bridge.c
@@ -223,7 +223,8 @@ void drm_bridge_post_disable(struct drm_bridge *bridge)
if (!bridge)
return;
- bridge->funcs->post_disable(bridge);
+ if (bridge->funcs->post_disable)
+ bridge->funcs->post_disable(bridge);
drm_bridge_post_disable(bridge->next);
}
@@ -273,7 +274,8 @@ void drm_bridge_pre_enable(struct drm_bridge *bridge)
drm_bridge_pre_enable(bridge->next);
- bridge->funcs->pre_enable(bridge);
+ if (bridge->funcs->pre_enable)
+ bridge->funcs->pre_enable(bridge);
}
EXPORT_SYMBOL(drm_bridge_pre_enable);
--
2.6.3
From: Liu Ying <[email protected]>
This patch adds device tree bindings for Synopsys DesignWare MIPI DSI
host controller DRM bridge driver.
Signed-off-by: Liu Ying <[email protected]>
Signed-off-by: Chris Zhong <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
Changes in v5: None
Changes in v4:
- remove the cfg clk
- remove gpr property from example, since it is noused now.
- add the description about ports
Changes in v3:
- move the dw_mipi_dsi.txt to Documentation/devicetree/bindings/display/bridge
Changes in v2: None
.../bindings/display/bridge/dw_mipi_dsi.txt | 74 ++++++++++++++++++++++
1 file changed, 74 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt
diff --git a/Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt b/Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt
new file mode 100644
index 0000000..2e1d197
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt
@@ -0,0 +1,74 @@
+Device-Tree bindings for Synopsys DesignWare MIPI DSI host controller
+
+The controller is a digital core that implements all protocol functions
+defined in the MIPI DSI specification, providing an interface between
+the system and the MIPI DPHY, and allowing communication with a MIPI DSI
+compliant display.
+
+Required properties:
+ - #address-cells: Should be <1>.
+ - #size-cells: Should be <0>.
+ - compatible: The first compatible string should be "fsl,imx6q-mipi-dsi"
+ for i.MX6q/sdl SoCs. For other SoCs, please refer to their specific
+ device tree binding documentations. A common compatible string
+ "snps,dw-mipi-dsi" should be appended for all SoCs.
+ - reg: Represent the physical address range of the controller.
+ - interrupts: Represent the controller's interrupt to the CPU(s).
+ - clocks, clock-names: Phandles to the controller's pll reference
+ clock(ref) and APB clock(pclk), as described in [1].
+ - port@[X]: SoC specific port nodes with endpoint definitions as defined
+ in Documentation/devicetree/bindings/media/video-interfaces.txt,
+ please refer to the SoC specific binding document:
+ * Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi-rockchip.txt
+
+
+For more required properties, please refer to relevant device tree binding
+documentations which describe the controller embedded in specific SoCs.
+
+Required sub-nodes:
+ - A node to represent a DSI peripheral as described in [2].
+
+For more required sub-nodes, please refer to relevant device tree binding
+documentations which describe the controller embedded in specific SoCs.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/display/mipi-dsi-bus.txt
+
+example:
+ mipi_dsi: mipi@021e0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-mipi-dsi", "snps,dw-mipi-dsi";
+ reg = <0x021e0000 0x4000>;
+ interrupts = <0 102 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_MIPI_CORE_CFG>,
+ <&clks IMX6QDL_CLK_MIPI_IPG>;
+ clock-names = "ref", "pclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ mipi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_mipi>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ mipi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_mipi>;
+ };
+ };
+ };
+
+ panel {
+ compatible = "truly,tft480800-16-e-dsi";
+ reg = <0>;
+ /* ... */
+ };
+ };
--
2.6.3
add Synopsys DesignWare MIPI DSI host controller driver support.
Signed-off-by: Chris Zhong <[email protected]>
Signed-off-by: Liu Ying <[email protected]>
---
Changes in v5:
Adviced by Thierry
- use hyphens instead of underscore
- use encoder in drm_bridge
- reformatting the dptdin table
- use readx_poll_timeout to check register
- use msleep to wait
- add a comment to explain how to program phy
- change the program code to symbolic names
- check this for validity of find_panel and clk_prepare_enable
- eliminate the configuration clock
- some optimization for coding style
Changes in v4:
- eliminate some warnning
Changes in v3: None
Changes in v2: None
drivers/gpu/drm/bridge/Kconfig | 10 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/dw-mipi-dsi.c | 1084 ++++++++++++++++++++++++++++++++++
include/drm/bridge/dw_mipi_dsi.h | 28 +
4 files changed, 1123 insertions(+)
create mode 100644 drivers/gpu/drm/bridge/dw-mipi-dsi.c
create mode 100644 include/drm/bridge/dw_mipi_dsi.h
diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index 6dddd39..d9ca7b4 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -22,6 +22,16 @@ config DRM_DW_HDMI_AHB_AUDIO
Designware HDMI block. This is used in conjunction with
the i.MX6 HDMI driver.
+config DRM_DW_MIPI_DSI
+ tristate "Synopsys DesignWare MIPI DSI host controller bridge"
+ depends on DRM
+ select DRM_KMS_HELPER
+ select DRM_MIPI_DSI
+ select DRM_PANEL
+ help
+ Choose this if you want to use the Synopsys DesignWare MIPI DSI host
+ controller bridge. If M is selected, the module will be
+ called dw-mipi-dsi.
config DRM_NXP_PTN3460
tristate "NXP PTN3460 DP/LVDS bridge"
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index d4e28be..96c54af 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -2,5 +2,6 @@ ccflags-y := -Iinclude/drm
obj-$(CONFIG_DRM_DW_HDMI) += dw_hdmi.o
obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw_hdmi-ahb-audio.o
+obj-$(CONFIG_DRM_DW_MIPI_DSI) += dw-mipi-dsi.o
obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
diff --git a/drivers/gpu/drm/bridge/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/dw-mipi-dsi.c
new file mode 100644
index 0000000..26b96e8
--- /dev/null
+++ b/drivers/gpu/drm/bridge/dw-mipi-dsi.c
@@ -0,0 +1,1084 @@
+/*
+ * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/iopoll.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <drm/bridge/dw_mipi_dsi.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+#include <video/mipi_display.h>
+
+#define DSI_VERSION 0x00
+
+#define DSI_PWR_UP 0x04
+#define RESET 0
+#define POWERUP BIT(0)
+
+#define DSI_CLKMGR_CFG 0x08
+#define TO_CLK_DIVIDSION(div) (((div) & 0xff) << 8)
+#define TX_ESC_CLK_DIVIDSION(div) (((div) & 0xff) << 0)
+
+#define DSI_DPI_VCID 0x0c
+#define DPI_VID(vid) (((vid) & 0x3) << 0)
+
+#define DSI_DPI_COLOR_CODING 0x10
+#define EN18_LOOSELY BIT(8)
+#define DPI_COLOR_CODING_16BIT_1 0x0
+#define DPI_COLOR_CODING_16BIT_2 0x1
+#define DPI_COLOR_CODING_16BIT_3 0x2
+#define DPI_COLOR_CODING_18BIT_1 0x3
+#define DPI_COLOR_CODING_18BIT_2 0x4
+#define DPI_COLOR_CODING_24BIT 0x5
+
+#define DSI_DPI_CFG_POL 0x14
+#define COLORM_ACTIVE_LOW BIT(4)
+#define SHUTD_ACTIVE_LOW BIT(3)
+#define HSYNC_ACTIVE_LOW BIT(2)
+#define VSYNC_ACTIVE_LOW BIT(1)
+#define DATAEN_ACTIVE_LOW BIT(0)
+
+#define DSI_DPI_LP_CMD_TIM 0x18
+#define OUTVACT_LPCMD_TIME(p) (((p) & 0xff) << 16)
+#define INVACT_LPCMD_TIME(p) ((p) & 0xff)
+
+#define DSI_DBI_CFG 0x20
+#define DSI_DBI_CMDSIZE 0x28
+
+#define DSI_PCKHDL_CFG 0x2c
+#define EN_CRC_RX BIT(4)
+#define EN_ECC_RX BIT(3)
+#define EN_BTA BIT(2)
+#define EN_EOTP_RX BIT(1)
+#define EN_EOTP_TX BIT(0)
+
+#define DSI_MODE_CFG 0x34
+#define ENABLE_VIDEO_MODE 0
+#define ENABLE_CMD_MODE BIT(0)
+
+#define DSI_VID_MODE_CFG 0x38
+#define FRAME_BTA_ACK BIT(14)
+#define ENABLE_LOW_POWER (0x3f << 8)
+#define ENABLE_LOW_POWER_MASK (0x3f << 8)
+#define VID_MODE_TYPE_BURST_SYNC_PULSES 0x2
+#define VID_MODE_TYPE_MASK 0x3
+
+#define DSI_VID_PKT_SIZE 0x3c
+#define VID_PKT_SIZE(p) (((p) & 0x3fff) << 0)
+#define VID_PKT_MAX_SIZE 0x3fff
+
+#define DSI_VID_HSA_TIME 0x48
+#define DSI_VID_HBP_TIME 0x4c
+#define DSI_VID_HLINE_TIME 0x50
+#define DSI_VID_VSA_LINES 0x54
+#define DSI_VID_VBP_LINES 0x58
+#define DSI_VID_VFP_LINES 0x5c
+#define DSI_VID_VACTIVE_LINES 0x60
+#define DSI_CMD_MODE_CFG 0x68
+#define MAX_RD_PKT_SIZE_LP BIT(24)
+#define DCS_LW_TX_LP BIT(19)
+#define DCS_SR_0P_TX_LP BIT(18)
+#define DCS_SW_1P_TX_LP BIT(17)
+#define DCS_SW_0P_TX_LP BIT(16)
+#define GEN_LW_TX_LP BIT(14)
+#define GEN_SR_2P_TX_LP BIT(13)
+#define GEN_SR_1P_TX_LP BIT(12)
+#define GEN_SR_0P_TX_LP BIT(11)
+#define GEN_SW_2P_TX_LP BIT(10)
+#define GEN_SW_1P_TX_LP BIT(9)
+#define GEN_SW_0P_TX_LP BIT(8)
+#define EN_ACK_RQST BIT(1)
+#define EN_TEAR_FX BIT(0)
+
+#define CMD_MODE_ALL_LP (MAX_RD_PKT_SIZE_LP | \
+ DCS_LW_TX_LP | \
+ DCS_SR_0P_TX_LP | \
+ DCS_SW_1P_TX_LP | \
+ DCS_SW_0P_TX_LP | \
+ GEN_LW_TX_LP | \
+ GEN_SR_2P_TX_LP | \
+ GEN_SR_1P_TX_LP | \
+ GEN_SR_0P_TX_LP | \
+ GEN_SW_2P_TX_LP | \
+ GEN_SW_1P_TX_LP | \
+ GEN_SW_0P_TX_LP)
+
+#define DSI_GEN_HDR 0x6c
+#define GEN_HDATA(data) (((data) & 0xffff) << 8)
+#define GEN_HDATA_MASK (0xffff << 8)
+#define GEN_HTYPE(type) (((type) & 0xff) << 0)
+#define GEN_HTYPE_MASK 0xff
+
+#define DSI_GEN_PLD_DATA 0x70
+
+#define DSI_CMD_PKT_STATUS 0x74
+#define GEN_CMD_EMPTY BIT(0)
+#define GEN_CMD_FULL BIT(1)
+#define GEN_PLD_W_EMPTY BIT(2)
+#define GEN_PLD_W_FULL BIT(3)
+#define GEN_PLD_R_EMPTY BIT(4)
+#define GEN_PLD_R_FULL BIT(5)
+#define GEN_RD_CMD_BUSY BIT(6)
+
+#define DSI_TO_CNT_CFG 0x78
+#define HSTX_TO_CNT(p) (((p) & 0xffff) << 16)
+#define LPRX_TO_CNT(p) ((p) & 0xffff)
+
+#define DSI_BTA_TO_CNT 0x8c
+
+#define DSI_LPCLK_CTRL 0x94
+#define AUTO_CLKLANE_CTRL BIT(1)
+#define PHY_TXREQUESTCLKHS BIT(0)
+
+#define DSI_PHY_TMR_LPCLK_CFG 0x98
+#define PHY_CLKHS2LP_TIME(lbcc) (((lbcc) & 0x3ff) << 16)
+#define PHY_CLKLP2HS_TIME(lbcc) ((lbcc) & 0x3ff)
+
+#define DSI_PHY_TMR_CFG 0x9c
+#define PHY_HS2LP_TIME(lbcc) (((lbcc) & 0xff) << 24)
+#define PHY_LP2HS_TIME(lbcc) (((lbcc) & 0xff) << 16)
+#define MAX_RD_TIME(lbcc) ((lbcc) & 0x7fff)
+
+#define DSI_PHY_RSTZ 0xa0
+#define PHY_DISFORCEPLL 0
+#define PHY_ENFORCEPLL BIT(3)
+#define PHY_DISABLECLK 0
+#define PHY_ENABLECLK BIT(2)
+#define PHY_RSTZ 0
+#define PHY_UNRSTZ BIT(1)
+#define PHY_SHUTDOWNZ 0
+#define PHY_UNSHUTDOWNZ BIT(0)
+
+#define DSI_PHY_IF_CFG 0xa4
+#define N_LANES(n) ((((n) - 1) & 0x3) << 0)
+#define PHY_STOP_WAIT_TIME(cycle) (((cycle) & 0xff) << 8)
+
+#define DSI_PHY_STATUS 0xb0
+#define LOCK BIT(0)
+#define STOP_STATE_CLK_LANE BIT(2)
+
+#define DSI_PHY_TST_CTRL0 0xb4
+#define PHY_TESTCLK BIT(1)
+#define PHY_UNTESTCLK 0
+#define PHY_TESTCLR BIT(0)
+#define PHY_UNTESTCLR 0
+
+#define DSI_PHY_TST_CTRL1 0xb8
+#define PHY_TESTEN BIT(16)
+#define PHY_UNTESTEN 0
+#define PHY_TESTDOUT(n) (((n) & 0xff) << 8)
+#define PHY_TESTDIN(n) (((n) & 0xff) << 0)
+
+#define DSI_INT_ST0 0xbc
+#define DSI_INT_ST1 0xc0
+#define DSI_INT_MSK0 0xc4
+#define DSI_INT_MSK1 0xc8
+
+#define PHY_STATUS_TIMEOUT_US 10000
+#define CMD_PKT_STATUS_TIMEOUT_US 20000
+
+#define BYPASS_VCO_RANGE BIT(7)
+#define VCO_RANGE_CON_SEL(val) (((val) & 0x7) << 3)
+#define VCO_IN_CAP_CON_DEFAULT (0x0 << 1)
+#define VCO_IN_CAP_CON_LOW (0x1 << 1)
+#define VCO_IN_CAP_CON_HIGH (0x2 << 1)
+#define REF_BIAS_CUR_SEL BIT(0)
+
+#define CP_CURRENT_3MA BIT(3)
+#define CP_PROGRAM_EN BIT(7)
+#define LPF_PROGRAM_EN BIT(6)
+#define LPF_RESISTORS_20_KOHM 0
+
+#define HSFREQRANGE_SEL(val) (((val) & 0x3f) << 1)
+
+#define INPUT_DIVIDER(val) ((val - 1) & 0x7f)
+#define LOW_PROGRAM_EN 0
+#define HIGH_PROGRAM_EN BIT(7)
+#define LOOP_DIV_LOW_SEL(val) ((val - 1) & 0x1f)
+#define LOOP_DIV_HIGH_SEL(val) (((val - 1) >> 5) & 0x1f)
+#define PLL_LOOP_DIV_EN BIT(5)
+#define PLL_INPUT_DIV_EN BIT(4)
+
+#define POWER_CONTROL BIT(6)
+#define INTERNAL_REG_CURRENT BIT(3)
+#define BIAS_BLOCK_ON BIT(2)
+#define BANDGAP_ON BIT(0)
+
+#define TER_RESISTOR_HIGH BIT(7)
+#define TER_RESISTOR_LOW 0
+#define LEVEL_SHIFTERS_ON BIT(6)
+#define TER_CAL_DONE BIT(5)
+#define SETRD_MAX (0x7 << 2)
+#define POWER_MANAGE BIT(1)
+#define TER_RESISTORS_ON BIT(0)
+
+#define BIASEXTR_SEL(val) ((val) & 0x7)
+#define BANDGAP_SEL(val) ((val) & 0x7)
+#define TLP_PROGRAM_EN BIT(7)
+#define THS_PRE_PROGRAM_EN BIT(7)
+#define THS_ZERO_PROGRAM_EN BIT(6)
+
+enum {
+ BANDGAP_97_07,
+ BANDGAP_98_05,
+ BANDGAP_99_02,
+ BANDGAP_100_00,
+ BANDGAP_93_17,
+ BANDGAP_94_15,
+ BANDGAP_95_12,
+ BANDGAP_96_10,
+};
+
+enum {
+ BIASEXTR_87_1,
+ BIASEXTR_91_5,
+ BIASEXTR_95_9,
+ BIASEXTR_100,
+ BIASEXTR_105_94,
+ BIASEXTR_111_88,
+ BIASEXTR_118_8,
+ BIASEXTR_127_7,
+};
+
+struct dw_mipi_dsi {
+ struct mipi_dsi_host dsi_host;
+ struct drm_connector connector;
+ struct drm_bridge *bridge;
+ struct drm_panel *panel;
+ struct device *dev;
+
+ void __iomem *base;
+
+ struct clk *pllref_clk;
+ struct clk *pclk;
+
+ unsigned int lane_mbps; /* per lane */
+ u32 channel;
+ u32 lanes;
+ u32 format;
+ u16 input_div;
+ u16 feedback_div;
+ struct drm_display_mode *mode;
+
+ const struct dw_mipi_dsi_plat_data *pdata;
+
+ bool enabled;
+};
+
+enum dw_mipi_dsi_mode {
+ DW_MIPI_DSI_CMD_MODE,
+ DW_MIPI_DSI_VID_MODE,
+};
+
+struct dphy_pll_testdin_map {
+ unsigned int max_mbps;
+ u8 testdin;
+};
+
+/* The table is based on 27MHz DPHY pll reference clock. */
+static const struct dphy_pll_testdin_map dptdin_map[] = {
+ { 90, 0x00}, { 100, 0x10}, { 110, 0x20}, { 130, 0x01},
+ { 140, 0x11}, { 150, 0x21}, { 170, 0x02}, { 180, 0x12},
+ { 200, 0x22}, { 220, 0x03}, { 240, 0x13}, { 250, 0x23},
+ { 270, 0x04}, { 300, 0x14}, { 330, 0x05}, { 360, 0x15},
+ { 400, 0x25}, { 450, 0x06}, { 500, 0x16}, { 550, 0x07},
+ { 600, 0x17}, { 650, 0x08}, { 700, 0x18}, { 750, 0x09},
+ { 800, 0x19}, { 850, 0x29}, { 900, 0x39}, { 950, 0x0a},
+ {1000, 0x1a}, {1050, 0x2a}, {1100, 0x3a}, {1150, 0x0b},
+ {1200, 0x1b}, {1250, 0x2b}, {1300, 0x3b}, {1350, 0x0c},
+ {1400, 0x1c}, {1450, 0x2c}, {1500, 0x3c}
+};
+
+static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host)
+{
+ return container_of(host, struct dw_mipi_dsi, dsi_host);
+}
+
+static inline struct dw_mipi_dsi *con_to_dsi(struct drm_connector *con)
+{
+ return container_of(con, struct dw_mipi_dsi, connector);
+}
+
+int dw_mipi_dsi_get_encoder_pixel_format(struct drm_encoder *encoder)
+{
+ struct dw_mipi_dsi *dsi = encoder->bridge->driver_private;
+
+ return dsi->format;
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi_get_encoder_pixel_format);
+
+static int max_mbps_to_testdin(unsigned int max_mbps)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(dptdin_map); i++)
+ if (dptdin_map[i].max_mbps > max_mbps)
+ return dptdin_map[i].testdin;
+
+ return -EINVAL;
+}
+
+static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val)
+{
+ writel(val, dsi->base + reg);
+}
+
+static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg)
+{
+ return readl(dsi->base + reg);
+}
+
+/*
+ * The controller should generate 2 frames before
+ * preparing the peripheral.
+ */
+static void dw_mipi_dsi_wait_for_two_frames(struct dw_mipi_dsi *dsi)
+{
+ int refresh, two_frames;
+
+ refresh = drm_mode_vrefresh(dsi->mode);
+ two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2;
+ msleep(two_frames);
+}
+
+static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi *dsi, u8 test_code,
+ u8 test_data)
+{
+ /*
+ * With the falling edge on TESTCLK, the TESTDIN[7:0] signal content
+ * is latched internally as the current test code. Test data is
+ * programmed internally by rising edge on TESTCLK.
+ */
+ dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR);
+
+ dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_TESTEN | PHY_TESTDOUT(0) |
+ PHY_TESTDIN(test_code));
+
+ dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR);
+
+ dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_UNTESTEN | PHY_TESTDOUT(0) |
+ PHY_TESTDIN(test_data));
+
+ dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR);
+}
+
+static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi)
+{
+ int ret, testdin, vco, val;
+
+ vco = (dsi->lane_mbps < 200) ? 0 : (dsi->lane_mbps + 100) / 200;
+
+ testdin = max_mbps_to_testdin(dsi->lane_mbps);
+ if (testdin < 0) {
+ dev_err(dsi->dev,
+ "failed to get testdin for %dmbps lane clock\n",
+ dsi->lane_mbps);
+ return testdin;
+ }
+
+ dsi_write(dsi, DSI_PWR_UP, POWERUP);
+
+ dw_mipi_dsi_phy_write(dsi, 0x10, BYPASS_VCO_RANGE |
+ VCO_RANGE_CON_SEL(vco) |
+ VCO_IN_CAP_CON_LOW |
+ REF_BIAS_CUR_SEL);
+
+ dw_mipi_dsi_phy_write(dsi, 0x11, CP_CURRENT_3MA);
+ dw_mipi_dsi_phy_write(dsi, 0x12, CP_PROGRAM_EN | LPF_PROGRAM_EN |
+ LPF_RESISTORS_20_KOHM);
+
+ dw_mipi_dsi_phy_write(dsi, 0x44, HSFREQRANGE_SEL(testdin));
+
+ dw_mipi_dsi_phy_write(dsi, 0x17, INPUT_DIVIDER(dsi->input_div));
+ dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_LOW_SEL(dsi->feedback_div) |
+ LOW_PROGRAM_EN);
+ dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_HIGH_SEL(dsi->feedback_div) |
+ HIGH_PROGRAM_EN);
+ dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN);
+
+ dw_mipi_dsi_phy_write(dsi, 0x20, POWER_CONTROL | INTERNAL_REG_CURRENT |
+ BIAS_BLOCK_ON | BANDGAP_ON);
+
+ dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_LOW | TER_CAL_DONE |
+ SETRD_MAX | TER_RESISTORS_ON);
+ dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_HIGH | LEVEL_SHIFTERS_ON |
+ SETRD_MAX | POWER_MANAGE |
+ TER_RESISTORS_ON);
+
+ dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN |
+ BIASEXTR_SEL(BIASEXTR_127_7));
+ dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN |
+ BANDGAP_SEL(BANDGAP_96_10));
+
+ dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | 0xf);
+ dw_mipi_dsi_phy_write(dsi, 0x71, THS_PRE_PROGRAM_EN | 0x55);
+ dw_mipi_dsi_phy_write(dsi, 0x72, THS_ZERO_PROGRAM_EN | 0xa);
+
+ dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
+ PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
+
+ ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS,
+ val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US);
+ if (ret < 0) {
+ dev_err(dsi->dev, "failed to wait for phy lock state\n");
+ return ret;
+ }
+
+ ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS,
+ val, val & STOP_STATE_CLK_LANE, 1000,
+ PHY_STATUS_TIMEOUT_US);
+ if (ret < 0) {
+ dev_err(dsi->dev,
+ "failed to wait for phy clk lane stop state\n");
+ return ret;
+ }
+
+ return ret;
+}
+
+static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi)
+{
+ unsigned int bpp, i, pre;
+ unsigned long mpclk, pllref, tmp;
+ unsigned int m = 1, n = 1, target_mbps = 1000;
+ unsigned int max_mbps = dptdin_map[ARRAY_SIZE(dptdin_map) - 1].max_mbps;
+
+ bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+ if (bpp < 0) {
+ dev_err(dsi->dev, "failed to get bpp for pixel format %d\n",
+ dsi->format);
+ return bpp;
+ }
+
+ mpclk = DIV_ROUND_UP(dsi->mode->clock, MSEC_PER_SEC);
+ if (mpclk) {
+ /* take 1 / 0.9, since mbps must big than bandwidth of RGB */
+ tmp = mpclk * (bpp / dsi->lanes) * 10 / 9;
+ if (tmp < max_mbps)
+ target_mbps = tmp;
+ else
+ dev_err(dsi->dev, "DPHY clock frequency is out of range\n");
+ }
+
+ pllref = DIV_ROUND_UP(clk_get_rate(dsi->pllref_clk), USEC_PER_SEC);
+ tmp = pllref;
+
+ for (i = 1; i < 6; i++) {
+ pre = pllref / i;
+ if ((tmp > (target_mbps % pre)) && (target_mbps / pre < 512)) {
+ tmp = target_mbps % pre;
+ n = i;
+ m = target_mbps / pre;
+ }
+ if (tmp == 0)
+ break;
+ }
+
+ dsi->lane_mbps = pllref / n * m;
+ dsi->input_div = n;
+ dsi->feedback_div = m;
+
+ return 0;
+}
+
+static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
+ struct mipi_dsi_device *device)
+{
+ struct dw_mipi_dsi *dsi = host_to_dsi(host);
+
+ if (device->lanes > dsi->pdata->max_data_lanes) {
+ dev_err(dsi->dev, "the number of data lanes(%u) is too many\n",
+ device->lanes);
+ return -EINVAL;
+ }
+
+ if (!(device->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) ||
+ !(device->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)) {
+ dev_err(dsi->dev, "device mode is unsupported\n");
+ return -EINVAL;
+ }
+
+ dsi->lanes = device->lanes;
+ dsi->channel = device->channel;
+ dsi->format = device->format;
+ dsi->panel = of_drm_find_panel(device->dev.of_node);
+ if (dsi->panel)
+ return drm_panel_attach(dsi->panel, &dsi->connector);
+
+ return -EINVAL;
+}
+
+static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
+ struct mipi_dsi_device *device)
+{
+ struct dw_mipi_dsi *dsi = host_to_dsi(host);
+
+ drm_panel_detach(dsi->panel);
+
+ return 0;
+}
+
+static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 val)
+{
+ int ret;
+
+ ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+ val, !(val & GEN_CMD_FULL), 1000,
+ CMD_PKT_STATUS_TIMEOUT_US);
+ if (ret < 0) {
+ dev_err(dsi->dev, "failed to get available command FIFO\n");
+ return ret;
+ }
+
+ dsi_write(dsi, DSI_GEN_HDR, val);
+
+ ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+ val, val & (GEN_CMD_EMPTY | GEN_PLD_W_EMPTY),
+ 1000, CMD_PKT_STATUS_TIMEOUT_US);
+ if (ret < 0) {
+ dev_err(dsi->dev, "failed to write command FIFO\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi,
+ const struct mipi_dsi_msg *msg)
+{
+ const u16 *tx_buf = msg->tx_buf;
+ u32 val = GEN_HDATA(*tx_buf) | GEN_HTYPE(msg->type);
+
+ if (msg->tx_len > 2) {
+ dev_err(dsi->dev, "too long tx buf length %zu for short write\n",
+ msg->tx_len);
+ return -EINVAL;
+ }
+
+ return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
+}
+
+static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi,
+ const struct mipi_dsi_msg *msg)
+{
+ const u32 *tx_buf = msg->tx_buf;
+ int len = msg->tx_len, pld_data_bytes = sizeof(*tx_buf), ret;
+ u32 val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type);
+ u32 remainder = 0;
+
+ if (msg->tx_len < 3) {
+ dev_err(dsi->dev, "wrong tx buf length %zu for long write\n",
+ msg->tx_len);
+ return -EINVAL;
+ }
+
+ while (DIV_ROUND_UP(len, pld_data_bytes)) {
+ if (len < pld_data_bytes) {
+ memcpy(&remainder, tx_buf, len);
+ dsi_write(dsi, DSI_GEN_PLD_DATA, remainder);
+ len = 0;
+ } else {
+ dsi_write(dsi, DSI_GEN_PLD_DATA, *tx_buf);
+ tx_buf++;
+ len -= pld_data_bytes;
+ }
+
+ ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS,
+ val, !(val & GEN_PLD_W_FULL), 1000,
+ CMD_PKT_STATUS_TIMEOUT_US);
+ if (ret < 0) {
+ dev_err(dsi->dev,
+ "failed to get available write payload FIFO\n");
+ return ret;
+ }
+ }
+
+ return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val);
+}
+
+static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
+ const struct mipi_dsi_msg *msg)
+{
+ struct dw_mipi_dsi *dsi = host_to_dsi(host);
+ int ret;
+
+ switch (msg->type) {
+ case MIPI_DSI_DCS_SHORT_WRITE:
+ case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
+ case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE:
+ ret = dw_mipi_dsi_dcs_short_write(dsi, msg);
+ break;
+ case MIPI_DSI_DCS_LONG_WRITE:
+ ret = dw_mipi_dsi_dcs_long_write(dsi, msg);
+ break;
+ default:
+ dev_err(dsi->dev, "unsupported message type\n");
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = {
+ .attach = dw_mipi_dsi_host_attach,
+ .detach = dw_mipi_dsi_host_detach,
+ .transfer = dw_mipi_dsi_host_transfer,
+};
+
+static enum drm_connector_status
+dw_mipi_dsi_detect(struct drm_connector *connector, bool force)
+{
+ return connector_status_connected;
+}
+
+static void dw_mipi_dsi_drm_connector_destroy(struct drm_connector *connector)
+{
+ drm_connector_unregister(connector);
+ drm_connector_cleanup(connector);
+}
+
+static struct drm_connector_funcs dw_mipi_dsi_connector_funcs = {
+ .dpms = drm_helper_connector_dpms,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .detect = dw_mipi_dsi_detect,
+ .destroy = dw_mipi_dsi_drm_connector_destroy,
+};
+
+static int dw_mipi_dsi_connector_get_modes(struct drm_connector *connector)
+{
+ struct dw_mipi_dsi *dsi = con_to_dsi(connector);
+
+ return drm_panel_get_modes(dsi->panel);
+}
+
+static enum drm_mode_status dw_mipi_dsi_mode_valid(
+ struct drm_connector *connector,
+ struct drm_display_mode *mode)
+{
+ struct dw_mipi_dsi *dsi = con_to_dsi(connector);
+
+ enum drm_mode_status mode_status = MODE_OK;
+
+ if (dsi->pdata->mode_valid)
+ mode_status = dsi->pdata->mode_valid(connector, mode);
+
+ return mode_status;
+}
+
+static struct drm_encoder *dw_mipi_dsi_connector_best_encoder(
+ struct drm_connector *connector)
+{
+ struct dw_mipi_dsi *dsi = con_to_dsi(connector);
+
+ return dsi->bridge->encoder;
+}
+
+static struct drm_connector_helper_funcs dw_mipi_dsi_connector_helper_funcs = {
+ .get_modes = dw_mipi_dsi_connector_get_modes,
+ .mode_valid = dw_mipi_dsi_mode_valid,
+ .best_encoder = dw_mipi_dsi_connector_best_encoder,
+};
+
+static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
+{
+ u32 val;
+
+ val = VID_MODE_TYPE_BURST_SYNC_PULSES | ENABLE_LOW_POWER;
+
+ dsi_write(dsi, DSI_VID_MODE_CFG, val);
+}
+
+static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi,
+ enum dw_mipi_dsi_mode mode)
+{
+ if (mode == DW_MIPI_DSI_CMD_MODE) {
+ dsi_write(dsi, DSI_PWR_UP, RESET);
+ dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
+ dsi_write(dsi, DSI_PWR_UP, POWERUP);
+ } else {
+ dsi_write(dsi, DSI_PWR_UP, RESET);
+ dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE);
+ dw_mipi_dsi_video_mode_config(dsi);
+ dsi_write(dsi, DSI_PWR_UP, POWERUP);
+ }
+}
+
+static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
+{
+ dsi_write(dsi, DSI_PWR_UP, RESET);
+ dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ);
+}
+
+static void dw_mipi_dsi_bridge_enable(struct drm_bridge *bridge)
+{
+ struct dw_mipi_dsi *dsi = bridge->driver_private;
+
+ if (dsi->enabled)
+ return;
+
+ if (clk_prepare_enable(dsi->pclk)) {
+ dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
+ return;
+ }
+
+ dw_mipi_dsi_phy_init(dsi);
+ dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
+ dw_mipi_dsi_wait_for_two_frames(dsi);
+ dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
+ if (drm_panel_prepare(dsi->panel)) {
+ dev_err(dsi->dev, "failed to prepare panel\n");
+ return;
+ }
+
+ dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
+ clk_disable_unprepare(dsi->pclk);
+
+ drm_panel_enable(dsi->panel);
+
+ dsi->enabled = true;
+}
+
+static void dw_mipi_dsi_bridge_disable(struct drm_bridge *bridge)
+{
+ struct dw_mipi_dsi *dsi = bridge->driver_private;
+
+ if (!dsi->enabled)
+ return;
+
+ drm_panel_disable(dsi->panel);
+
+ if (clk_prepare_enable(dsi->pclk)) {
+ dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
+ return;
+ }
+
+ dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
+ drm_panel_unprepare(dsi->panel);
+ dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE);
+
+ /*
+ * This is necessary to make sure the peripheral will be driven
+ * normally when the display is enabled again later.
+ */
+ msleep(120);
+
+ dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE);
+ dw_mipi_dsi_disable(dsi);
+ clk_disable_unprepare(dsi->pclk);
+
+ dsi->enabled = false;
+}
+
+static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
+{
+ dsi_write(dsi, DSI_PWR_UP, RESET);
+ dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
+ | PHY_RSTZ | PHY_SHUTDOWNZ);
+ dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) |
+ TX_ESC_CLK_DIVIDSION(7));
+ dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS);
+}
+
+static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
+ struct drm_display_mode *mode)
+{
+ u32 val = 0, color = 0;
+
+ switch (dsi->format) {
+ case MIPI_DSI_FMT_RGB888:
+ color = DPI_COLOR_CODING_24BIT;
+ break;
+ case MIPI_DSI_FMT_RGB666:
+ color = DPI_COLOR_CODING_18BIT_2 | EN18_LOOSELY;
+ break;
+ case MIPI_DSI_FMT_RGB666_PACKED:
+ color = DPI_COLOR_CODING_18BIT_1;
+ break;
+ case MIPI_DSI_FMT_RGB565:
+ color = DPI_COLOR_CODING_16BIT_1;
+ break;
+ }
+
+ if (!(mode->flags & DRM_MODE_FLAG_PVSYNC))
+ val |= VSYNC_ACTIVE_LOW;
+ if (!(mode->flags & DRM_MODE_FLAG_PHSYNC))
+ val |= HSYNC_ACTIVE_LOW;
+
+ dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel));
+ dsi_write(dsi, DSI_DPI_COLOR_CODING, color);
+ dsi_write(dsi, DSI_DPI_CFG_POL, val);
+ dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(4)
+ | INVACT_LPCMD_TIME(4));
+}
+
+static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi)
+{
+ dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA);
+}
+
+static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi,
+ struct drm_display_mode *mode)
+{
+ dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay));
+}
+
+static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
+{
+ dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000));
+ dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
+ dsi_write(dsi, DSI_CMD_MODE_CFG, CMD_MODE_ALL_LP);
+ dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
+}
+
+/* Get lane byte clock cycles. */
+static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi,
+ u32 hcomponent)
+{
+ u32 frac, lbcc;
+
+ lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8;
+
+ frac = lbcc % dsi->mode->clock;
+ lbcc = lbcc / dsi->mode->clock;
+ if (frac)
+ lbcc++;
+
+ return lbcc;
+}
+
+static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi)
+{
+ u32 htotal, hsa, hbp, lbcc;
+ struct drm_display_mode *mode = dsi->mode;
+
+ htotal = mode->htotal;
+ hsa = mode->hsync_end - mode->hsync_start;
+ hbp = mode->htotal - mode->hsync_end;
+
+ lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, htotal);
+ dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc);
+
+ lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, hsa);
+ dsi_write(dsi, DSI_VID_HSA_TIME, lbcc);
+
+ lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, hbp);
+ dsi_write(dsi, DSI_VID_HBP_TIME, lbcc);
+}
+
+static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi)
+{
+ u32 vactive, vsa, vfp, vbp;
+ struct drm_display_mode *mode = dsi->mode;
+
+ vactive = mode->vdisplay;
+ vsa = mode->vsync_end - mode->vsync_start;
+ vfp = mode->vsync_start - mode->vdisplay;
+ vbp = mode->vtotal - mode->vsync_end;
+
+ dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive);
+ dsi_write(dsi, DSI_VID_VSA_LINES, vsa);
+ dsi_write(dsi, DSI_VID_VFP_LINES, vfp);
+ dsi_write(dsi, DSI_VID_VBP_LINES, vbp);
+}
+
+static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi)
+{
+ dsi_write(dsi, DSI_PHY_TMR_CFG, PHY_HS2LP_TIME(0x40)
+ | PHY_LP2HS_TIME(0x40) | MAX_RD_TIME(10000));
+
+ dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG, PHY_CLKHS2LP_TIME(0x40)
+ | PHY_CLKLP2HS_TIME(0x40));
+}
+
+static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi)
+{
+ dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) |
+ N_LANES(dsi->lanes));
+}
+
+static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
+{
+ dsi_read(dsi, DSI_INT_ST0);
+ dsi_read(dsi, DSI_INT_ST1);
+ dsi_write(dsi, DSI_INT_MSK0, 0);
+ dsi_write(dsi, DSI_INT_MSK1, 0);
+}
+
+static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct dw_mipi_dsi *dsi = bridge->driver_private;
+ int ret;
+
+ dsi->mode = adjusted_mode;
+
+ ret = dw_mipi_dsi_get_lane_bps(dsi);
+ if (ret < 0)
+ return;
+
+ if (clk_prepare_enable(dsi->pclk)) {
+ dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__);
+ return;
+ }
+
+ dw_mipi_dsi_init(dsi);
+ dw_mipi_dsi_dpi_config(dsi, mode);
+ dw_mipi_dsi_packet_handler_config(dsi);
+ dw_mipi_dsi_video_mode_config(dsi);
+ dw_mipi_dsi_video_packet_config(dsi, mode);
+ dw_mipi_dsi_command_mode_config(dsi);
+ dw_mipi_dsi_line_timer_config(dsi);
+ dw_mipi_dsi_vertical_timing_config(dsi);
+ dw_mipi_dsi_dphy_timing_config(dsi);
+ dw_mipi_dsi_dphy_interface_config(dsi);
+ dw_mipi_dsi_clear_err(dsi);
+ dw_mipi_dsi_phy_init(dsi);
+ dw_mipi_dsi_wait_for_two_frames(dsi);
+ if (drm_panel_prepare(dsi->panel)) {
+ dev_err(dsi->dev, "failed to prepare panel\n");
+ return;
+ }
+
+ clk_disable_unprepare(dsi->pclk);
+}
+
+static bool dw_mipi_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
+ const struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ return true;
+}
+
+static const struct drm_bridge_funcs dw_mipi_dsi_bridge_funcs = {
+ .enable = dw_mipi_dsi_bridge_enable,
+ .disable = dw_mipi_dsi_bridge_disable,
+ .mode_set = dw_mipi_dsi_bridge_mode_set,
+ .mode_fixup = dw_mipi_dsi_bridge_mode_fixup,
+};
+
+static int dw_mipi_dsi_register(struct drm_device *drm, struct dw_mipi_dsi *dsi,
+ struct drm_encoder *encoder)
+{
+ struct drm_bridge *bridge;
+ int ret;
+
+ bridge = devm_kzalloc(drm->dev, sizeof(*bridge), GFP_KERNEL);
+ if (!bridge)
+ return -ENOMEM;
+
+ dsi->bridge = bridge;
+ encoder->bridge = bridge;
+ bridge->driver_private = dsi;
+ bridge->encoder = encoder;
+
+ bridge->funcs = &dw_mipi_dsi_bridge_funcs;
+ ret = drm_bridge_attach(drm, bridge);
+ if (ret) {
+ DRM_ERROR("failed to initialize bridge with drm\n");
+ return ret;
+ }
+
+
+ drm_connector_helper_add(&dsi->connector,
+ &dw_mipi_dsi_connector_helper_funcs);
+ drm_connector_init(drm, &dsi->connector, &dw_mipi_dsi_connector_funcs,
+ DRM_MODE_CONNECTOR_DSI);
+
+ drm_mode_connector_attach_encoder(&dsi->connector, encoder);
+
+ return 0;
+}
+
+int dw_mipi_dsi_bind(struct device *dev, struct device *master, void *data,
+ struct drm_encoder *encoder,
+ const struct dw_mipi_dsi_plat_data *pdata)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct resource *res;
+ struct drm_device *drm = data;
+ struct dw_mipi_dsi *dsi;
+ u32 val;
+ int ret;
+
+ dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
+ if (!dsi)
+ return -ENOMEM;
+
+ dsi->pdata = pdata;
+ dsi->dev = dev;
+ dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
+ dsi->dsi_host.dev = dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENODEV;
+
+ dsi->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(dsi->base))
+ return PTR_ERR(dsi->base);
+
+ dsi->pllref_clk = devm_clk_get(dev, "ref");
+ if (IS_ERR(dsi->pllref_clk)) {
+ ret = PTR_ERR(dsi->pllref_clk);
+ dev_err(dev, "Unable to get pll reference clock: %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(dsi->pllref_clk);
+ if (ret) {
+ dev_err(dev, "%s: Failed to enable pllref_clk\n", __func__);
+ return ret;
+ }
+
+ dsi->pclk = devm_clk_get(dev, "pclk");
+ if (IS_ERR(dsi->pclk)) {
+ ret = PTR_ERR(dsi->pclk);
+ dev_err(dev, "Unable to get pclk: %d\n", ret);
+ goto err_pllref;
+ }
+
+ ret = clk_prepare_enable(dsi->pclk);
+ if (ret) {
+ dev_err(dev, "%s: Failed to enable pclk\n", __func__);
+ return ret;
+ }
+
+ val = dsi_read(dsi, DSI_VERSION);
+ clk_disable_unprepare(dsi->pclk);
+
+ ret = dw_mipi_dsi_register(drm, dsi, encoder);
+ if (ret) {
+ dev_err(dev, "Unable to register dsi: %d\n", ret);
+ goto err_pllref;
+ }
+ dev_set_drvdata(dev, dsi);
+
+ return mipi_dsi_host_register(&dsi->dsi_host);
+
+err_pllref:
+ clk_disable_unprepare(dsi->pllref_clk);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi_bind);
+
+void dw_mipi_dsi_unbind(struct device *dev, struct device *master, void *data)
+{
+ struct dw_mipi_dsi *dsi = dev_get_drvdata(dev);
+
+ mipi_dsi_host_unregister(&dsi->dsi_host);
+ clk_disable_unprepare(dsi->pllref_clk);
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi_unbind);
+
+MODULE_DESCRIPTION("Synopsys DesignWare MIPI DSI host controller driver");
+MODULE_AUTHOR("Chris Zhong <[email protected]>");
+MODULE_LICENSE("GPL");
diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h
new file mode 100644
index 0000000..991c065
--- /dev/null
+++ b/include/drm/bridge/dw_mipi_dsi.h
@@ -0,0 +1,28 @@
+/*
+ * Copyright (C) 2014-2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ */
+
+#ifndef __DW_MIPI_DSI__
+#define __DW_MIPI_DSI__
+
+#include <drm/drmP.h>
+
+struct dw_mipi_dsi_plat_data {
+ unsigned int max_data_lanes;
+ enum drm_mode_status (*mode_valid)(struct drm_connector *connector,
+ struct drm_display_mode *mode);
+};
+
+int dw_mipi_dsi_get_encoder_pixel_format(struct drm_encoder *encoder);
+
+int dw_mipi_dsi_bind(struct device *dev, struct device *master,
+ void *data, struct drm_encoder *encoder,
+ const struct dw_mipi_dsi_plat_data *pdata);
+void dw_mipi_dsi_unbind(struct device *dev, struct device *master, void *data);
+
+#endif /* __DW_MIPI_DSI__ */
--
2.6.3
Add support for Synopsys DesignWare MIPI DSI host controller which is
embedded in the rk3288 SoCs.
Signed-off-by: Chris Zhong <[email protected]>
---
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
drivers/gpu/drm/rockchip/Kconfig | 10 +
drivers/gpu/drm/rockchip/Makefile | 1 +
drivers/gpu/drm/rockchip/dw_mipi_dsi_rockchip.c | 249 ++++++++++++++++++++++++
drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 3 +
4 files changed, 263 insertions(+)
create mode 100644 drivers/gpu/drm/rockchip/dw_mipi_dsi_rockchip.c
diff --git a/drivers/gpu/drm/rockchip/Kconfig b/drivers/gpu/drm/rockchip/Kconfig
index 35215f6..24395f3 100644
--- a/drivers/gpu/drm/rockchip/Kconfig
+++ b/drivers/gpu/drm/rockchip/Kconfig
@@ -25,3 +25,13 @@ config ROCKCHIP_DW_HDMI
for the Synopsys DesignWare HDMI driver. If you want to
enable HDMI on RK3288 based SoC, you should selet this
option.
+
+config ROCKCHIP_DW_MIPI_DSI
+ bool "Rockchip specific extensions for Synopsys DW MIPI DSI"
+ depends on DRM_ROCKCHIP
+ select DRM_DW_MIPI_DSI
+ help
+ This selects support for Rockchip SoC specific extensions
+ for the Synopsys DesignWare HDMI driver. If you want to
+ enable MIPI DSI on RK3288 based SoC, you should selet this
+ option.
diff --git a/drivers/gpu/drm/rockchip/Makefile b/drivers/gpu/drm/rockchip/Makefile
index f3d8a19..6a97059 100644
--- a/drivers/gpu/drm/rockchip/Makefile
+++ b/drivers/gpu/drm/rockchip/Makefile
@@ -6,5 +6,6 @@ rockchipdrm-y := rockchip_drm_drv.o rockchip_drm_fb.o rockchip_drm_fbdev.o \
rockchip_drm_gem.o
obj-$(CONFIG_ROCKCHIP_DW_HDMI) += dw_hdmi-rockchip.o
+obj-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw_mipi_dsi_rockchip.o
obj-$(CONFIG_DRM_ROCKCHIP) += rockchipdrm.o rockchip_drm_vop.o
diff --git a/drivers/gpu/drm/rockchip/dw_mipi_dsi_rockchip.c b/drivers/gpu/drm/rockchip/dw_mipi_dsi_rockchip.c
new file mode 100644
index 0000000..a0bb4eb
--- /dev/null
+++ b/drivers/gpu/drm/rockchip/dw_mipi_dsi_rockchip.c
@@ -0,0 +1,249 @@
+/*
+ * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/component.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/videodev2.h>
+#include <drm/bridge/dw_mipi_dsi.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_of.h>
+
+#include "rockchip_drm_drv.h"
+#include "rockchip_drm_vop.h"
+
+#define DRIVER_NAME "rockchip-mipi-dsi"
+
+#define GRF_SOC_CON6 0x025c
+#define DSI0_SEL_VOP_LIT (1 << 6)
+#define DSI1_SEL_VOP_LIT (1 << 9)
+
+struct rockchip_mipi_dsi {
+ struct drm_encoder encoder;
+ struct device *dev;
+ struct regmap *regmap;
+};
+
+static inline struct rockchip_mipi_dsi *enc_to_dsi(struct drm_encoder *enc)
+{
+ return container_of(enc, struct rockchip_mipi_dsi, encoder);
+}
+
+static struct drm_encoder_funcs rockchip_mipi_dsi_encoder_funcs = {
+ .destroy = drm_encoder_cleanup,
+};
+
+static int rockchip_mipi_parse_dt(struct rockchip_mipi_dsi *dsi)
+{
+ struct device_node *np = dsi->dev->of_node;
+
+ dsi->regmap = syscon_regmap_lookup_by_phandle(np, "rockchip,grf");
+ if (IS_ERR(dsi->regmap)) {
+ dev_err(dsi->dev, "Unable to get rockchip,grf\n");
+ return PTR_ERR(dsi->regmap);
+ }
+
+ return 0;
+}
+
+static bool rockchip_mipi_dsi_encoder_mode_fixup(struct drm_encoder *encoder,
+ const struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ return true;
+}
+
+static void rockchip_mipi_dsi_encoder_prepare(struct drm_encoder *encoder)
+{
+ u32 encoder_pix_fmt, interface_pix_fmt;
+
+ encoder_pix_fmt = dw_mipi_dsi_get_encoder_pixel_format(encoder);
+
+ switch (encoder_pix_fmt) {
+ case MIPI_DSI_FMT_RGB888:
+ interface_pix_fmt = ROCKCHIP_OUT_MODE_P888;
+ break;
+ case MIPI_DSI_FMT_RGB666:
+ interface_pix_fmt = ROCKCHIP_OUT_MODE_P666;
+ break;
+ case MIPI_DSI_FMT_RGB565:
+ interface_pix_fmt = ROCKCHIP_OUT_MODE_P565;
+ break;
+ default:
+ WARN_ON(1);
+ return;
+ }
+
+ rockchip_drm_crtc_mode_config(encoder->crtc, DRM_MODE_CONNECTOR_DSI,
+ interface_pix_fmt);
+}
+
+static void rockchip_mipi_dsi_encoder_mode_set(struct drm_encoder *encoder,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+}
+
+static void rockchip_mipi_dsi_encoder_commit(struct drm_encoder *encoder)
+{
+ struct rockchip_mipi_dsi *dsi = enc_to_dsi(encoder);
+ u32 val;
+ int mux = rockchip_drm_encoder_get_mux_id(dsi->dev->of_node, encoder);
+
+ if (mux)
+ val = DSI0_SEL_VOP_LIT | (DSI0_SEL_VOP_LIT << 16);
+ else
+ val = DSI0_SEL_VOP_LIT << 16;
+
+ regmap_write(dsi->regmap, GRF_SOC_CON6, val);
+ dev_dbg(dsi->dev, "vop %s output to dsi0\n",
+ (mux) ? "LIT" : "BIG");
+}
+
+static void rockchip_mipi_dsi_encoder_disable(struct drm_encoder *encoder)
+{
+}
+
+static struct drm_encoder_helper_funcs
+rockchip_mipi_dsi_encoder_helper_funcs = {
+ .mode_fixup = rockchip_mipi_dsi_encoder_mode_fixup,
+ .prepare = rockchip_mipi_dsi_encoder_prepare,
+ .mode_set = rockchip_mipi_dsi_encoder_mode_set,
+ .commit = rockchip_mipi_dsi_encoder_commit,
+ .disable = rockchip_mipi_dsi_encoder_disable,
+};
+
+static int rockchip_mipi_dsi_register(struct drm_device *drm,
+ struct rockchip_mipi_dsi *dsi)
+{
+ struct drm_encoder *encoder = &dsi->encoder;
+ struct device *dev = dsi->dev;
+
+ encoder->possible_crtcs = drm_of_find_possible_crtcs(drm,
+ dev->of_node);
+ /*
+ * If we failed to find the CRTC(s) which this encoder is
+ * supposed to be connected to, it's because the CRTC has
+ * not been registered yet. Defer probing, and hope that
+ * the required CRTC is added later.
+ */
+ if (encoder->possible_crtcs == 0)
+ return -EPROBE_DEFER;
+
+ drm_encoder_helper_add(&dsi->encoder,
+ &rockchip_mipi_dsi_encoder_helper_funcs);
+ drm_encoder_init(drm, &dsi->encoder, &rockchip_mipi_dsi_encoder_funcs,
+ DRM_MODE_ENCODER_DSI);
+ return 0;
+}
+
+static enum drm_mode_status rockchip_mipi_dsi_mode_valid(
+ struct drm_connector *connector,
+ struct drm_display_mode *mode)
+{
+ /*
+ * The VID_PKT_SIZE field in the DSI_VID_PKT_CFG
+ * register is 11-bit.
+ */
+ if (mode->hdisplay > 0x7ff)
+ return MODE_BAD_HVALUE;
+
+ /*
+ * The V_ACTIVE_LINES field in the DSI_VTIMING_CFG
+ * register is 11-bit.
+ */
+ if (mode->vdisplay > 0x7ff)
+ return MODE_BAD_VVALUE;
+
+ return MODE_OK;
+}
+
+static struct dw_mipi_dsi_plat_data rk3288_mipi_dsi_drv_data = {
+ .max_data_lanes = 4,
+ .mode_valid = rockchip_mipi_dsi_mode_valid,
+};
+
+static const struct of_device_id rockchip_mipi_dsi_dt_ids[] = {
+ {
+ .compatible = "rockchip,rk3288-mipi-dsi",
+ .data = &rk3288_mipi_dsi_drv_data,
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rockchip_mipi_dsi_dt_ids);
+
+static int rockchip_mipi_dsi_bind(struct device *dev, struct device *master,
+ void *data)
+{
+ const struct of_device_id *of_id =
+ of_match_device(rockchip_mipi_dsi_dt_ids, dev);
+ const struct dw_mipi_dsi_plat_data *pdata = of_id->data;
+ struct drm_device *drm = data;
+ struct rockchip_mipi_dsi *dsi;
+ int ret;
+
+ dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
+ if (!dsi)
+ return -ENOMEM;
+
+ dsi->dev = dev;
+
+ ret = rockchip_mipi_dsi_register(drm, dsi);
+ if (ret)
+ return ret;
+
+ ret = rockchip_mipi_parse_dt(dsi);
+ if (ret)
+ return ret;
+
+ dev_set_drvdata(dev, dsi);
+
+ return dw_mipi_dsi_bind(dev, master, data, &dsi->encoder, pdata);
+}
+
+static void rockchip_mipi_dsi_unbind(struct device *dev, struct device *master,
+ void *data)
+{
+ return dw_mipi_dsi_unbind(dev, master, data);
+}
+
+static const struct component_ops rockchip_mipi_dsi_ops = {
+ .bind = rockchip_mipi_dsi_bind,
+ .unbind = rockchip_mipi_dsi_unbind,
+};
+
+static int rockchip_mipi_dsi_probe(struct platform_device *pdev)
+{
+ return component_add(&pdev->dev, &rockchip_mipi_dsi_ops);
+}
+
+static int rockchip_mipi_dsi_remove(struct platform_device *pdev)
+{
+ component_del(&pdev->dev, &rockchip_mipi_dsi_ops);
+ return 0;
+}
+
+static struct platform_driver rockchip_mipi_dsi_driver = {
+ .probe = rockchip_mipi_dsi_probe,
+ .remove = rockchip_mipi_dsi_remove,
+ .driver = {
+ .of_match_table = rockchip_mipi_dsi_dt_ids,
+ .name = DRIVER_NAME,
+ },
+};
+module_platform_driver(rockchip_mipi_dsi_driver);
+
+MODULE_DESCRIPTION("ROCKCHIP MIPI DSI host controller driver");
+MODULE_AUTHOR("Chris Zhong <[email protected]>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index eff545b..bfaa31a 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -1199,6 +1199,9 @@ static int vop_crtc_mode_set(struct drm_crtc *crtc,
case DRM_MODE_CONNECTOR_HDMIA:
VOP_CTRL_SET(vop, hdmi_en, 1);
break;
+ case DRM_MODE_CONNECTOR_DSI:
+ VOP_CTRL_SET(vop, mipi_en, 1);
+ break;
default:
DRM_ERROR("unsupport connector_type[%d]\n",
vop->connector_type);
--
2.6.3
add device tree bindings for rk3288 specific Synopsys DW MIPI DSI driver
Signed-off-by: Chris Zhong <[email protected]>
Acked-by: Rob Herring <[email protected]>
---
Changes in v5: None
Changes in v4: None
Changes in v3:
- move dw_mipi_dsi_rockchip.txt to bindings/display/rockchip/
Changes in v2: None
.../display/rockchip/dw_mipi_dsi_rockchip.txt | 56 ++++++++++++++++++++++
1 file changed, 56 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
diff --git a/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
new file mode 100644
index 0000000..acd9ec9
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/rockchip/dw_mipi_dsi_rockchip.txt
@@ -0,0 +1,56 @@
+Rockchip specific extensions to the Synopsys Designware MIPI DSI
+================================
+
+Required properties:
+- compatible: "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi".
+- rockchip,grf: this soc should set GRF regs to mux vopl/vopb.
+- ports: contain a port node with endpoint definitions as defined in [1].
+ For vopb,set the reg = <0> and set the reg = <1> for vopl.
+
+For more required properties, please refer to [2].
+
+[1] Documentation/devicetree/bindings/media/video-interfaces.txt
+[2] Documentation/devicetree/bindings/display/bridge/dw_mipi_dsi.txt
+
+Example:
+ mipi_dsi: mipi@ff960000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi";
+ reg = <0xff960000 0x4000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>;
+ clock-names = "ref", "pclk";
+ rockchip,grf = <&grf>;
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ mipi_in: port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mipi_in_vopb: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&vopb_out_mipi>;
+ };
+ mipi_in_vopl: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&vopl_out_mipi>;
+ };
+ };
+ };
+
+ panel {
+ compatible ="boe,tv080wum-nl0";
+ reg = <0>;
+
+ enable-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_en>;
+ backlight = <&backlight>;
+ status = "okay";
+ };
+ };
--
2.6.3
Add a mipi_dsi node, and also add mipi_dsi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Chris Zhong <[email protected]>
---
Changes in v5:
- modify the clk name to SCLK_MIPIDSI_24M
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/boot/dts/rk3288.dtsi | 39 +++++++++++++++++++++++++++++++++++++++
1 file changed, 39 insertions(+)
diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index 6a79c9c..c48891e 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -798,6 +798,10 @@
reg = <0>;
remote-endpoint = <&hdmi_in_vopb>;
};
+ vopb_out_mipi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&mipi_in_vopb>;
+ };
};
};
@@ -831,6 +835,10 @@
reg = <0>;
remote-endpoint = <&hdmi_in_vopl>;
};
+ vopl_out_mipi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&mipi_in_vopl>;
+ };
};
};
@@ -871,6 +879,37 @@
};
};
+ mipi_dsi: mipi@ff960000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi";
+ reg = <0xff960000 0x4000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru SCLK_MIPIDSI_24M>, <&cru PCLK_MIPI_DSI0>;
+ clock-names = "ref", "pclk";
+ rockchip,grf = <&grf>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ mipi_in: port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ mipi_in_vopb: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&vopb_out_mipi>;
+ };
+ mipi_in_vopl: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&vopl_out_mipi>;
+ };
+ };
+ };
+ };
+
gic: interrupt-controller@ffc01000 {
compatible = "arm,gic-400";
interrupt-controller;
--
2.6.3
This tv080wum-nl0 panel is a mipi panel, it can use in MIPI_TX socket
of rk3288 evb board.
Signed-off-by: Chris Zhong <[email protected]>
---
Changes in v5:
- add a blank line befor lcd_en
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/arm/boot/dts/rk3288-evb.dtsi | 20 +++++++++++++++++++-
1 file changed, 19 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/rk3288-evb.dtsi b/arch/arm/boot/dts/rk3288-evb.dtsi
index f6d2e78..2014992 100644
--- a/arch/arm/boot/dts/rk3288-evb.dtsi
+++ b/arch/arm/boot/dts/rk3288-evb.dtsi
@@ -47,7 +47,7 @@
reg = <0x0 0x80000000>;
};
- backlight {
+ backlight: backlight {
compatible = "pwm-backlight";
brightness-levels = <
0 1 2 3 4 5 6 7
@@ -177,6 +177,20 @@
status = "okay";
};
+&mipi_dsi {
+ status = "okay";
+ panel {
+ compatible ="boe,tv080wum-nl0";
+ reg = <0>;
+
+ enable-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_en>;
+ backlight = <&backlight>;
+ status = "okay";
+ };
+};
+
&sdmmc {
bus-width = <4>;
cap-mmc-highspeed;
@@ -247,6 +261,10 @@
bl_en: bl-en {
rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
};
+
+ lcd_en: lcd-en {
+ rockchip,pins = <7 3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
};
buttons {
--
2.6.3
Hi Chris,
Am Donnerstag, 26. November 2015, 15:50:15 schrieb Chris Zhong:
> Adds a new id for the sclk supplying the mipidsi on rk3288 socs.
>
> Signed-off-by: Chris Zhong <[email protected]>
applied this patch to my clock-branch for 4.5, after fixing the numbering to
not conflict with the new crypto-clock.
Heiko
Hi Chris,
Am Donnerstag, 26. November 2015, 15:50:16 schrieb Chris Zhong:
> sclk_mipidsi_24m is the gating of mipi dsi phy.
>
> Signed-off-by: Chris Zhong <[email protected]>
> Acked-by: Stephen Boyd <[email protected]>
applied this to my clock branch for 4.5
Heiko