From: Alex Smith <[email protected]>
Add device tree nodes for the NEMC and BCH to the JZ4780 device tree,
and make use of them in the Ci20 device tree to add a node for the
board's NAND.
Note that since the pinctrl driver is not yet upstream, this includes
neither pin configuration nor busy/write-protect GPIO pins for the
NAND. Use of the NAND relies on the boot loader to have left the pins
configured in a usable state, which should be the case when booted
from the NAND.
Signed-off-by: Alex Smith <[email protected]>
Cc: Zubair Lutfullah Kakakhel <[email protected]>
Cc: David Woodhouse <[email protected]>
Cc: Brian Norris <[email protected]>
Cc: Paul Burton <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Signed-off-by: Harvey Hunt <[email protected]>
---
v9 -> v10:
- No change.
v8 -> v9:
- Represent the partition table as a subnode of a NAND chip.
v7 -> v8:
- Describe the NAND chips as children nodes of the NAND controller.
- Remove ingenic, prefix from ECC settings.
- Renamed some ECC settings.
v6 -> v7:
- Add nand-ecc-mode to DT.
- Add nand-on-flash-bbt to DT.
v4 -> v5:
- New patch adding DT nodes for the NAND so that the driver can be
tested.
arch/mips/boot/dts/ingenic/ci20.dts | 63 ++++++++++++++++++++++++++++++++++
arch/mips/boot/dts/ingenic/jz4780.dtsi | 26 ++++++++++++++
2 files changed, 89 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index 9fcb9e7..782258c 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -42,3 +42,66 @@
&uart4 {
status = "okay";
};
+
+&nemc {
+ status = "okay";
+
+ nandc: nand-controller@1 {
+ compatible = "ingenic,jz4780-nand";
+ reg = <1 0 0x1000000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ingenic,bch-controller = <&bch>;
+
+ ingenic,nemc-tAS = <10>;
+ ingenic,nemc-tAH = <5>;
+ ingenic,nemc-tBP = <10>;
+ ingenic,nemc-tAW = <15>;
+ ingenic,nemc-tSTRV = <100>;
+
+ nand@1 {
+ reg = <1>;
+
+ nand-ecc-step-size = <1024>;
+ nand-ecc-strength = <24>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+
+ partitions {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ partition@0 {
+ label = "u-boot-spl";
+ reg = <0x0 0x0 0x0 0x800000>;
+ };
+
+ partition@0x800000 {
+ label = "u-boot";
+ reg = <0x0 0x800000 0x0 0x200000>;
+ };
+
+ partition@0xa00000 {
+ label = "u-boot-env";
+ reg = <0x0 0xa00000 0x0 0x200000>;
+ };
+
+ partition@0xc00000 {
+ label = "boot";
+ reg = <0x0 0xc00000 0x0 0x4000000>;
+ };
+
+ partition@0x8c00000 {
+ label = "system";
+ reg = <0x0 0x4c00000 0x1 0xfb400000>;
+ };
+ };
+ };
+ };
+};
+
+&bch {
+ status = "okay";
+};
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
index 65389f6..b868b42 100644
--- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -108,4 +108,30 @@
status = "disabled";
};
+
+ nemc: nemc@13410000 {
+ compatible = "ingenic,jz4780-nemc";
+ reg = <0x13410000 0x10000>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <1 0 0x1b000000 0x1000000
+ 2 0 0x1a000000 0x1000000
+ 3 0 0x19000000 0x1000000
+ 4 0 0x18000000 0x1000000
+ 5 0 0x17000000 0x1000000
+ 6 0 0x16000000 0x1000000>;
+
+ clocks = <&cgu JZ4780_CLK_NEMC>;
+
+ status = "disabled";
+ };
+
+ bch: bch@134d0000 {
+ compatible = "ingenic,jz4780-bch";
+ reg = <0x134d0000 0x10000>;
+
+ clocks = <&cgu JZ4780_CLK_BCH>;
+
+ status = "disabled";
+ };
};
--
2.6.4
On Thu, 24 Dec 2015 12:20:15 +0000
Harvey Hunt <[email protected]> wrote:
> From: Alex Smith <[email protected]>
>
> Add device tree nodes for the NEMC and BCH to the JZ4780 device tree,
> and make use of them in the Ci20 device tree to add a node for the
> board's NAND.
>
> Note that since the pinctrl driver is not yet upstream, this includes
> neither pin configuration nor busy/write-protect GPIO pins for the
> NAND. Use of the NAND relies on the boot loader to have left the pins
> configured in a usable state, which should be the case when booted
> from the NAND.
>
> Signed-off-by: Alex Smith <[email protected]>
> Cc: Zubair Lutfullah Kakakhel <[email protected]>
> Cc: David Woodhouse <[email protected]>
> Cc: Brian Norris <[email protected]>
> Cc: Paul Burton <[email protected]>
> Cc: [email protected]
> Cc: [email protected]
> Cc: [email protected]
> Cc: [email protected]
> Cc: [email protected]
> Signed-off-by: Harvey Hunt <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
> ---
> v9 -> v10:
> - No change.
>
> v8 -> v9:
> - Represent the partition table as a subnode of a NAND chip.
>
> v7 -> v8:
> - Describe the NAND chips as children nodes of the NAND controller.
> - Remove ingenic, prefix from ECC settings.
> - Renamed some ECC settings.
>
> v6 -> v7:
> - Add nand-ecc-mode to DT.
> - Add nand-on-flash-bbt to DT.
>
> v4 -> v5:
> - New patch adding DT nodes for the NAND so that the driver can be
> tested.
>
> arch/mips/boot/dts/ingenic/ci20.dts | 63 ++++++++++++++++++++++++++++++++++
> arch/mips/boot/dts/ingenic/jz4780.dtsi | 26 ++++++++++++++
> 2 files changed, 89 insertions(+)
>
> diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
> index 9fcb9e7..782258c 100644
> --- a/arch/mips/boot/dts/ingenic/ci20.dts
> +++ b/arch/mips/boot/dts/ingenic/ci20.dts
> @@ -42,3 +42,66 @@
> &uart4 {
> status = "okay";
> };
> +
> +&nemc {
> + status = "okay";
> +
> + nandc: nand-controller@1 {
> + compatible = "ingenic,jz4780-nand";
> + reg = <1 0 0x1000000>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ingenic,bch-controller = <&bch>;
> +
> + ingenic,nemc-tAS = <10>;
> + ingenic,nemc-tAH = <5>;
> + ingenic,nemc-tBP = <10>;
> + ingenic,nemc-tAW = <15>;
> + ingenic,nemc-tSTRV = <100>;
> +
> + nand@1 {
> + reg = <1>;
> +
> + nand-ecc-step-size = <1024>;
> + nand-ecc-strength = <24>;
> + nand-ecc-mode = "hw";
> + nand-on-flash-bbt;
> +
> + partitions {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + partition@0 {
> + label = "u-boot-spl";
> + reg = <0x0 0x0 0x0 0x800000>;
> + };
> +
> + partition@0x800000 {
> + label = "u-boot";
> + reg = <0x0 0x800000 0x0 0x200000>;
> + };
> +
> + partition@0xa00000 {
> + label = "u-boot-env";
> + reg = <0x0 0xa00000 0x0 0x200000>;
> + };
> +
> + partition@0xc00000 {
> + label = "boot";
> + reg = <0x0 0xc00000 0x0 0x4000000>;
> + };
> +
> + partition@0x8c00000 {
> + label = "system";
> + reg = <0x0 0x4c00000 0x1 0xfb400000>;
> + };
> + };
> + };
> + };
> +};
> +
> +&bch {
> + status = "okay";
> +};
> diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
> index 65389f6..b868b42 100644
> --- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
> +++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
> @@ -108,4 +108,30 @@
>
> status = "disabled";
> };
> +
> + nemc: nemc@13410000 {
> + compatible = "ingenic,jz4780-nemc";
> + reg = <0x13410000 0x10000>;
> + #address-cells = <2>;
> + #size-cells = <1>;
> + ranges = <1 0 0x1b000000 0x1000000
> + 2 0 0x1a000000 0x1000000
> + 3 0 0x19000000 0x1000000
> + 4 0 0x18000000 0x1000000
> + 5 0 0x17000000 0x1000000
> + 6 0 0x16000000 0x1000000>;
> +
> + clocks = <&cgu JZ4780_CLK_NEMC>;
> +
> + status = "disabled";
> + };
> +
> + bch: bch@134d0000 {
> + compatible = "ingenic,jz4780-bch";
> + reg = <0x134d0000 0x10000>;
> +
> + clocks = <&cgu JZ4780_CLK_BCH>;
> +
> + status = "disabled";
> + };
> };
--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com