2016-03-04 12:38:12

by Lothar Waßmann

[permalink] [raw]
Subject: ARM: dts: imx6ul: add more functionality to i.MX6UL

[PATCHv3 1/2] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
[PATCHv3 2/2] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL mainboard

This patchset adds more functionality to the i.MX6UL machines.

Changes vs. v1:
- added patch to implement KPP clock for i.MX6UL to prevent conflicts
when this patch would go via a different tree.
- added board support for Ka-Ro electronics TX6UL module for the same
reason
- added imx6ul specific compatibles as requested by Lucas Stach

Changes vs. v2:
- dropped patches which have already been applied in the meantime
- addressed comments by Shawn Guo


2016-03-04 12:38:17

by Lothar Waßmann

[permalink] [raw]
Subject: [PATCHv3 1/2] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules

The TXUL-0010/-0011 modules are Computers On Module manufactured by
Ka-Ro electronics GmbH with the following characteristics:
Processor Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
RAM 256MB 16-bit DDR3 SDRAM
ROM 128MB NAND Flash (TXUL-0010) / 4GB eMMC (TXUL-0011)
Power supply Single 3.3 to 5V
Size 26mm SO-DIMM
Temp. Range -40°C to 85°C

Signed-off-by: Lothar Waßmann <[email protected]>
---
arch/arm/boot/dts/Makefile | 4 +-
arch/arm/boot/dts/imx6ul-tx6ul-0010.dts | 53 ++
arch/arm/boot/dts/imx6ul-tx6ul-0011.dts | 68 +++
arch/arm/boot/dts/imx6ul-tx6ul.dtsi | 973 ++++++++++++++++++++++++++++++++
4 files changed, 1097 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx6ul-tx6ul-0010.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tx6ul-0011.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tx6ul.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 072294f..a5e21ae 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -374,7 +374,9 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-sdb-reva.dtb \
imx6sx-sdb.dtb
dtb-$(CONFIG_SOC_IMX6UL) += \
- imx6ul-14x14-evk.dtb
+ imx6ul-14x14-evk.dtb \
+ imx6ul-tx6ul-0010.dtb \
+ imx6ul-tx6ul-0011.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
imx7d-sbc-imx7.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-0010.dts b/arch/arm/boot/dts/imx6ul-tx6ul-0010.dts
new file mode 100644
index 0000000..8c2f3df
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tx6ul-0010.dts
@@ -0,0 +1,53 @@
+/*
+ * Copyright 2015 Lothar Waßmann <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-tx6ul.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-0010 Module";
+ compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
+
+ aliases {
+ /delete-property/ mmc1;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-0011.dts b/arch/arm/boot/dts/imx6ul-tx6ul-0011.dts
new file mode 100644
index 0000000..d82698e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tx6ul-0011.dts
@@ -0,0 +1,68 @@
+/*
+ * Copyright 2015 Lothar Waßmann <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-tx6ul.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-0011 Module";
+ compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
+
+ aliases {
+ mmc0 = &usdhc2;
+ mmc1 = &usdhc1;
+ };
+};
+
+&gpmi {
+ status = "disabled";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <4>;
+ no-1-8-v;
+ non-removable;
+ fsl,wp-controller;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
new file mode 100644
index 0000000..437e9aa
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
@@ -0,0 +1,973 @@
+/*
+ * Copyright 2015 Lothar Waßmann <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ can0 = &can2;
+ can1 = &can1;
+ display = &display;
+ i2c0 = &i2c2;
+ i2c1 = &i2c_gpio;
+ i2c2 = &i2c1;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ lcdif_23bit_pins_a = &pinctrl_disp0_1;
+ lcdif_24bit_pins_a = &pinctrl_disp0_2;
+ pwm0 = &pwm5;
+ reg_can_xcvr = &reg_can_xcvr;
+ serial2 = &uart5;
+ serial4 = &uart3;
+ spi0 = &ecspi2;
+ spi1 = &spi_gpio;
+ stk5led = &user_led;
+ usbh1 = &usbotg2;
+ usbotg = &usbotg1;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0 0>; /* will be filled by U-Boot */
+ };
+
+ clocks {
+ mclk: mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ };
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_rst>;
+ enable-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ pwms = <&pwm5 0 500000 PWM_POLARITY_INVERTED>;
+ power-supply = <&reg_lcd_pwr>;
+ /*
+ * a poor man's way to create a 1:1 relationship between
+ * the PWM value and the actual duty cycle
+ */
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100>;
+ default-brightness-level = <50>;
+ };
+
+ i2c_gpio: i2c-gpio {
+ compatible = "i2c-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c_gpio>;
+ gpios = <
+ &gpio5 1 GPIO_ACTIVE_HIGH /* SDA */
+ &gpio5 0 GPIO_ACTIVE_HIGH /* SCL */
+ >;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ ds1339: rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ status = "disabled";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ user_led: user {
+ label = "Heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led>;
+ gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_3v3_etn: regulator-3v3etn {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_ETN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy_power>;
+ gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_2v5: regulator-2v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_can_xcvr: regulator-canxcvr {
+ compatible = "regulator-fixed";
+ regulator-name = "CAN XCVR";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan_xcvr>;
+ gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ enable-active-low;
+ };
+
+ reg_lcd_pwr: regulator-lcdpwr {
+ compatible = "regulator-fixed";
+ regulator-name = "LCD POWER";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_pwr>;
+ gpio = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_usbh1_vbus: regulator-usbh1vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus &pinctrl_usbh1_oc>;
+ gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbotg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus &pinctrl_usbotg_oc>;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ spi_gpio: spi-gpio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "spi-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi_gpio>;
+ gpio-mosi = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <2>;
+ cs-gpios = <
+ &gpio1 29 GPIO_ACTIVE_HIGH
+ &gpio1 10 GPIO_ACTIVE_HIGH
+ >;
+ status = "disabled";
+
+ spi@0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <660000>;
+ };
+
+ spi@1 {
+ compatible = "spidev";
+ reg = <1>;
+ spi-max-frequency = <660000>;
+ };
+ };
+
+ sound {
+ compatible = "karo,imx6ul-tx6ul-sgtl5000",
+ "simple-audio-card";
+ simple-audio-card,name = "imx6ul-tx6ul-sgtl5000-audio";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&codec_dai>;
+ simple-audio-card,frame-master = <&codec_dai>;
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Line", "Line In",
+ "Line", "Line Out",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+
+ cpu_dai: simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ };
+
+ codec_dai: simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ };
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <&reg_can_xcvr>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <&reg_can_xcvr>;
+ status = "okay";
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <
+ &gpio1 29 GPIO_ACTIVE_HIGH
+ &gpio1 10 GPIO_ACTIVE_HIGH
+ >;
+ status = "disabled";
+
+ spidev0: spi@0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <60000000>;
+ };
+
+ spidev1: spi@1 {
+ compatible = "spidev";
+ reg = <1>;
+ spi-max-frequency = <60000000>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio &pinctrl_etnphy0_rst>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
+ phy-supply = <&reg_3v3_etn>;
+ phy-handle = <&etnphy0>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ etnphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy0_int>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+ status = "okay";
+ };
+
+ etnphy1: ethernet-phy@2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy1_int>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+ status = "okay";
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2 &pinctrl_etnphy1_rst>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ phy-supply = <&reg_3v3_etn>;
+ phy-handle = <&etnphy1>;
+ status = "disabled";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ fsl,no-blockmark-swap;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ sgtl5000: codec@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <&reg_2v5>;
+ VDDIO-supply = <&reg_3v3>;
+ clocks = <&mclk>;
+ };
+
+ polytouch: polytouch@38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_edt_ft5x06>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+
+ touchscreen: touchscreen@48 {
+ compatible = "ti,tsc2007";
+ reg = <0x48>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc2007>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <26 IRQ_TYPE_NONE>;
+ gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+ ti,x-plate-ohms = <660>;
+ wakeup-source;
+ };
+};
+
+&kpp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_kpp>;
+ /* sample keymap */
+ /* row/col 0..3 are mapped to KPP row/col 4..7 */
+ linux,keymap = <
+ MATRIX_KEY(4, 4, KEY_POWER)
+ MATRIX_KEY(4, 5, KEY_KP0)
+ MATRIX_KEY(4, 6, KEY_KP1)
+ MATRIX_KEY(4, 7, KEY_KP2)
+ MATRIX_KEY(5, 4, KEY_KP3)
+ MATRIX_KEY(5, 5, KEY_KP4)
+ MATRIX_KEY(5, 6, KEY_KP5)
+ MATRIX_KEY(5, 7, KEY_KP6)
+ MATRIX_KEY(6, 4, KEY_KP7)
+ MATRIX_KEY(6, 5, KEY_KP8)
+ MATRIX_KEY(6, 6, KEY_KP9)
+ >;
+ status = "okay";
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_disp0_1>;
+ lcd-supply = <&reg_lcd_pwr>;
+ display = <&display>;
+ status = "okay";
+
+ display: display@di0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+ status = "okay";
+
+ display-timings {
+ VGA {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <48>;
+ hsync-len = <96>;
+ hfront-porch = <16>;
+ vback-porch = <31>;
+ vsync-len = <2>;
+ vfront-porch = <12>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ETV570 {
+ clock-frequency = <25200000>;
+ hactive = <640>;
+ vactive = <480>;
+ hback-porch = <114>;
+ hsync-len = <30>;
+ hfront-porch = <16>;
+ vback-porch = <32>;
+ vsync-len = <3>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0350 {
+ clock-frequency = <6413760>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <34>;
+ hsync-len = <34>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0430 {
+ clock-frequency = <9009000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <2>;
+ hsync-len = <41>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vsync-len = <10>;
+ vfront-porch = <2>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+
+ ET0500 {
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ET0700 { /* same as ET0500 */
+ clock-frequency = <33264000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hsync-len = <128>;
+ hfront-porch = <40>;
+ vback-porch = <33>;
+ vsync-len = <2>;
+ vfront-porch = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ ETQ570 {
+ clock-frequency = <6596040>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hsync-len = <30>;
+ hfront-porch = <30>;
+ vback-porch = <16>;
+ vsync-len = <3>;
+ vfront-porch = <4>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&pwm5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm5>;
+ #pwm-cells = <3>;
+ status = "okay";
+};
+
+&sai2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai2>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5 &pinctrl_uart5_rtscts>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <&reg_usbotg_vbus>;
+ dr_mode = "peripheral";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <&reg_usbh1_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_usdhc1_cd>;
+ bus-width = <4>;
+ no-1-8-v;
+ cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+ fsl,wp-controller;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ };
+
+ pinctrl_led: ledgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x0b0b0 /* LED */
+ >;
+ };
+
+ pinctrl_disp0_1: disp0grp-1 {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
+ /* PAD DISP0_DAT0 is used for the Flexcan transceiver control on STK5-v5 */
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
+ >;
+ };
+
+ pinctrl_disp0_2: disp0grp-2 {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x10
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x10
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x10
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x10
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x10
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x10
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI 0x0b0b0 /* CSPI_MOSI */
+ MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO 0x0b0b0 /* CSPI_MISO */
+ MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK 0x0b0b0 /* CSPI_SCLK */
+ >;
+ };
+
+ pinctrl_edt_ft5x06: edt-ft5x06grp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* Interrupt */
+ MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* Reset */
+ MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Wake */
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x000b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x000b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x000b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x000b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x000b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x000b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x000b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x400000b1
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x000b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x000b0
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x000b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x000b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x000b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x000b0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x000b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x400000b1
+ >;
+ };
+
+ pinctrl_enet1_mdio: enet1-mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x0b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_etnphy_power: etnphy-pwrgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x0b0b0 /* ETN PHY POWER */
+ >;
+ };
+
+ pinctrl_etnphy0_int: etnphy-intgrp-0 {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 /* ETN PHY INT */
+ >;
+ };
+
+ pinctrl_etnphy0_rst: etnphy-rstgrp-0 {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x0b0b0 /* ETN PHY RESET */
+ >;
+ };
+
+ pinctrl_etnphy1_int: etnphy-intgrp-1 {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA06__GPIO4_IO27 0x0b0b0 /* ETN PHY INT */
+ >;
+ };
+
+ pinctrl_etnphy1_rst: etnphy-rstgrp-1 {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA07__GPIO4_IO28 0x0b0b0 /* ETN PHY RESET */
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x0b0b0
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_flexcan_xcvr: flexcan-xcvrgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0x0b0b0 /* Flexcan XCVR enable */
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
+ >;
+ };
+
+ pinctrl_i2c_gpio: i2c-gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x4001b8b1 /* I2C SCL */
+ MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x4001b8b1 /* I2C SDA */
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__I2C2_SCL 0x4001b8b1
+ MX6UL_PAD_GPIO1_IO01__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_kpp: kppgrp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_DATA1__KPP_COL04 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__KPP_COL05 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__KPP_COL06 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__KPP_COL07 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__KPP_ROW04 0x1b0b0
+ MX6UL_PAD_ENET2_RX_EN__KPP_ROW05 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__KPP_ROW06 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__KPP_ROW07 0x1b0b0
+ >;
+ };
+
+ pinctrl_lcd_pwr: lcd-pwrgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 /* LCD Power Enable */
+ >;
+ };
+
+ pinctrl_lcd_rst: lcd-rstgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__GPIO3_IO04 0x0b0b0 /* LCD Reset */
+ >;
+ };
+
+ pinctrl_pwm5: pwm5grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DQS__PWM5_OUT 0x0b0b0
+ >;
+ };
+
+ pinctrl_sai2: sai2grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x0b0b0 /* SSI1_RXD */
+ MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x0b0b0 /* SSI1_TXD */
+ MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x0b0b0 /* SSI1_CLK */
+ MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x0b0b0 /* SSI1_FS */
+ >;
+ };
+
+ pinctrl_spi_gpio: spi-gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_JTAG_MOD__GPIO1_IO10 0x0b0b0 /* CSPI_SS */
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x0b0b0 /* CSPI_MOSI */
+ MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x0b0b0 /* CSPI_MISO */
+ MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x0b0b0 /* CSPI_SCLK */
+ >;
+ };
+
+ pinctrl_tsc2007: tsc2007grp {
+ fsl,pins = <
+ MX6UL_PAD_JTAG_TMS__GPIO1_IO11 0x1b0b0 /* Interrupt */
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart1_rtscts: uart1-rtsctsgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_RTS_B__UART1_DCE_RTS 0x0b0b0
+ MX6UL_PAD_UART1_CTS_B__UART1_DCE_CTS 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart2_rtscts: uart2-rtsctsgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x0b0b0
+ MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO04__UART5_DCE_TX 0x0b0b0
+ MX6UL_PAD_GPIO1_IO05__UART5_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart5_rtscts: uart5-rtsctsgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS 0x0b0b0
+ MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS 0x0b0b0
+ >;
+ };
+
+ pinctrl_usbh1_oc: usbh1-ocgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x17059 /* USBH1_OC */
+ >;
+ };
+
+ pinctrl_usbh1_vbus: usbh1-vbusgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x0b0b0 /* USBH1_VBUSEN */
+ >;
+ };
+
+ pinctrl_usbotg_oc: usbotg-ocgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_RTS_B__GPIO1_IO27 0x17059 /* USBOTG_OC */
+ >;
+ };
+
+ pinctrl_usbotg_vbus: usbotg-vbusgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_CTS_B__GPIO1_IO26 0x1b0b0 /* USBOTG_VBUSEN */
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1
+ >;
+ };
+
+ pinctrl_usdhc1_cd: usdhc1cdgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CE1_B__GPIO4_IO14 0x170b0 /* SD1 CD */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x070b1
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x070b1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x070b1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x070b1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x070b1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x070b1
+ /* eMMC RESET */
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
+ >;
+ };
+};
--
2.1.4

2016-03-04 12:38:39

by Lothar Waßmann

[permalink] [raw]
Subject: [PATCHv3 2/2] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL mainboard

Signed-off-by: Lothar Waßmann <[email protected]>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts | 271 +++++++++++++++++++++++++++
2 files changed, 273 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a5e21ae..9f6af0f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -376,7 +376,8 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-14x14-evk.dtb \
imx6ul-tx6ul-0010.dtb \
- imx6ul-tx6ul-0011.dtb
+ imx6ul-tx6ul-0011.dtb \
+ imx6ul-tx6ul-mainboard.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
imx7d-sbc-imx7.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts b/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
new file mode 100644
index 0000000..d25899b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
@@ -0,0 +1,271 @@
+/*
+ * Copyright 2015 Lothar Waßmann <[email protected]>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-tx6ul.dtsi"
+
+/ {
+ model = "Ka-Ro electronics TXUL-0010 Module on TXUL Mainboard";
+ compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
+
+ aliases {
+ lcdif_24bit_pins_a = &pinctrl_disp0_3;
+ mmc0 = &usdhc1;
+ /delete-property/ mmc1;
+ serial2 = &uart3;
+ serial4 = &uart5;
+ };
+ /delete-node/ sound;
+};
+
+&can1 {
+ xceiver-supply = <&reg_3v3>;
+};
+
+&can2 {
+ xceiver-supply = <&reg_3v3>;
+};
+
+&ds1339 {
+ status = "disabled";
+};
+
+&fec1 {
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_etnphy0_rst>;
+ /delete-node/ mdio;
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio &pinctrl_etnphy1_rst>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ phy-supply = <&reg_3v3_etn>;
+ phy-handle = <&etnphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ etnphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy0_int>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&gpio5 5 IRQ_TYPE_EDGE_FALLING>;
+ status = "okay";
+ };
+
+ etnphy1: ethernet-phy@2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_etnphy1_int>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+ interrupts-extended = <&gpio4 27 IRQ_TYPE_EDGE_FALLING>;
+ status = "okay";
+ };
+ };
+};
+
+&i2c_gpio {
+ status = "disabled";
+};
+
+&i2c2 {
+ /delete-node/ codec@0a;
+ /delete-node/ touchscreen@48;
+
+ rtc: mcp7940x@6f {
+ compatible = "microchip,mcp7940x";
+ reg = <0x6f>;
+ };
+};
+
+&kpp {
+ status = "disabled";
+};
+
+&lcdif {
+ pinctrl-0 = <&pinctrl_disp0_3>;
+};
+
+&reg_usbotg_vbus{
+ status = "disabled";
+};
+
+&usdhc1 {
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ non-removable;
+ /delete-property/ cd-gpios;
+ cap-sdio-irq;
+};
+
+&uart1 {
+ pinctrl-0 = <&pinctrl_uart1>;
+ /delete-property/ fsl,uart-has-rtscts;
+};
+
+&uart2 {
+ pinctrl-0 = <&pinctrl_uart2>;
+ /delete-property/ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart6>;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart7>;
+ status = "okay";
+};
+
+&uart8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart8>;
+ status = "disabled"; /* conflicts with LCDIF */
+};
+
+&iomuxc {
+ hoggrp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x0b0b0 /* WLAN_RESET */
+ >;
+ };
+
+ pinctrl_disp0_3: disp0grp-3 {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x10 /* LSCLK */
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x10 /* OE_ACD */
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x10 /* HSYNC */
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x10
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x10
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x10
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x10
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x10
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x10
+ /* LCD_DATA08..09 not wired */
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x10
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x10
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x10
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x10
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x10
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x10
+ /* LCD_DATA16..17 not wired */
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x10
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x10
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x10
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x10
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x10
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x10
+ >;
+ };
+
+ pinctrl_enet2_mdio: enet2-mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x0b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x0b0b0
+ MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart6: uart6grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__UART6_DCE_TX 0x0b0b0
+ MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart7: uart7grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA16__UART7_DCE_TX 0x0b0b0
+ MX6UL_PAD_LCD_DATA17__UART7_DCE_RX 0x0b0b0
+ >;
+ };
+
+ pinctrl_uart8: uart8grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA20__UART8_DCE_TX 0x0b0b0
+ MX6UL_PAD_LCD_DATA21__UART8_DCE_RX 0x0b0b0
+ >;
+ };
+};
--
2.1.4

2016-03-30 11:43:48

by Shawn Guo

[permalink] [raw]
Subject: Re: ARM: dts: imx6ul: add more functionality to i.MX6UL

On Fri, Mar 04, 2016 at 01:37:21PM +0100, Lothar Wa?mann wrote:
> [PATCHv3 1/2] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL modules
> [PATCHv3 2/2] ARM: dts: imx6ul: add support for Ka-Ro electronics TXUL mainboard

Applied both, thanks.

>
> This patchset adds more functionality to the i.MX6UL machines.
>
> Changes vs. v1:
> - added patch to implement KPP clock for i.MX6UL to prevent conflicts
> when this patch would go via a different tree.
> - added board support for Ka-Ro electronics TX6UL module for the same
> reason
> - added imx6ul specific compatibles as requested by Lucas Stach
>
> Changes vs. v2:
> - dropped patches which have already been applied in the meantime
> - addressed comments by Shawn Guo
>
>