The Amlogic Meson GXL SoCs have an internal RMII PHY that is muxed with the
external RGMII pins.
In order to support switching between the two PHYs links, extended registers
size for mdio-mux-mmioreg must be added.
The DT related patches submitted as RFC in [3] will be sent in a separate
patchset due to multiple patchsets and DTSI migrations.
Changes since v2 RFC patchset at : [3]
- Change phy Kconfig/Makefile alphabetic order
- GXL dtsi cleanup
Changes since original RFC patchset at : [2]
- Remove meson8b experimental phy switching
- Switch to mdio-mux-mmioreg with extennded size support
- Add internal phy support for S905x and p231
- Add external PHY support for p230
[1] http://lkml.kernel.org/r/[email protected]
[2] http://lkml.kernel.org/r/[email protected]
[3] http://lkml.kernel.org/r/[email protected]
Neil Armstrong (2):
net: mdio-mux-mmioreg: Add support for 16bit and 32bit register sizes
net: phy: Add Meson GXL Internal PHY driver
.../devicetree/bindings/net/mdio-mux-mmioreg.txt | 4 +-
drivers/net/phy/Kconfig | 5 ++
drivers/net/phy/Makefile | 1 +
drivers/net/phy/mdio-mux-mmioreg.c | 60 ++++++++++++----
drivers/net/phy/meson-gxl.c | 81 ++++++++++++++++++++++
5 files changed, 136 insertions(+), 15 deletions(-)
create mode 100644 drivers/net/phy/meson-gxl.c
--
1.9.1
Add driver for the Internal RMII PHY found in the Amlogic Meson GXL SoCs.
This PHY seems to only implement some standard registers and need some
workarounds to provide autoneg values from vendor registers.
Some magic values are currently used to configure the PHY, and this a
temporary setup until clarification about these registers names and
registers fields are provided by Amlogic.
Signed-off-by: Neil Armstrong <[email protected]>
---
drivers/net/phy/Kconfig | 5 +++
drivers/net/phy/Makefile | 1 +
drivers/net/phy/meson-gxl.c | 81 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 87 insertions(+)
create mode 100644 drivers/net/phy/meson-gxl.c
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 2651c8d..b48943a 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -264,6 +264,11 @@ config MARVELL_PHY
---help---
Currently has a driver for the 88E1011S
+config MESON_GXL_PHY
+ tristate "Amlogic Meson GXL Internal PHY"
+ ---help---
+ Currently has a driver for the Amlogic Meson GXL Internal PHY
+
config MICREL_PHY
tristate "Micrel PHYs"
---help---
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index e58667d..3cd5af7 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -41,6 +41,7 @@ obj-$(CONFIG_INTEL_XWAY_PHY) += intel-xway.o
obj-$(CONFIG_LSI_ET1011C_PHY) += et1011c.o
obj-$(CONFIG_LXT_PHY) += lxt.o
obj-$(CONFIG_MARVELL_PHY) += marvell.o
+obj-$(CONFIG_MESON_GXL_PHY) += meson-gxl.o
obj-$(CONFIG_MICREL_KS8995MA) += spi_ks8995.o
obj-$(CONFIG_MICREL_PHY) += micrel.o
obj-$(CONFIG_MICROCHIP_PHY) += microchip.o
diff --git a/drivers/net/phy/meson-gxl.c b/drivers/net/phy/meson-gxl.c
new file mode 100644
index 0000000..1ea69b7
--- /dev/null
+++ b/drivers/net/phy/meson-gxl.c
@@ -0,0 +1,81 @@
+/*
+ * Amlogic Meson GXL Internal PHY Driver
+ *
+ * Copyright (C) 2015 Amlogic, Inc. All rights reserved.
+ * Copyright (C) 2016 BayLibre, SAS. All rights reserved.
+ * Author: Neil Armstrong <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+#include <linux/netdevice.h>
+
+static int meson_gxl_config_init(struct phy_device *phydev)
+{
+ /* Enable Analog and DSP register Bank access by */
+ phy_write(phydev, 0x14, 0x0000);
+ phy_write(phydev, 0x14, 0x0400);
+ phy_write(phydev, 0x14, 0x0000);
+ phy_write(phydev, 0x14, 0x0400);
+
+ /* Write Analog register 23 */
+ phy_write(phydev, 0x17, 0x8E0D);
+ phy_write(phydev, 0x14, 0x4417);
+
+ /* Enable fractional PLL */
+ phy_write(phydev, 0x17, 0x0005);
+ phy_write(phydev, 0x14, 0x5C1B);
+
+ /* Program fraction FR_PLL_DIV1 */
+ phy_write(phydev, 0x17, 0x029A);
+ phy_write(phydev, 0x14, 0x5C1D);
+
+ /* Program fraction FR_PLL_DIV1 */
+ phy_write(phydev, 0x17, 0xAAAA);
+ phy_write(phydev, 0x14, 0x5C1C);
+
+ return 0;
+}
+
+static struct phy_driver meson_gxl_phy[] = {
+ {
+ .phy_id = 0x01814400,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Meson GXL Internal PHY",
+ .features = PHY_BASIC_FEATURES,
+ .flags = PHY_IS_INTERNAL,
+ .config_init = meson_gxl_config_init,
+ .config_aneg = genphy_config_aneg,
+ .aneg_done = genphy_aneg_done,
+ .read_status = genphy_read_status,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ },
+};
+
+static struct mdio_device_id __maybe_unused meson_gxl_tbl[] = {
+ { 0x01814400, 0xfffffff0 },
+ { }
+};
+
+module_phy_driver(meson_gxl_phy);
+
+MODULE_DEVICE_TABLE(mdio, meson_gxl_tbl);
+
+MODULE_DESCRIPTION("Amlogic Meson GXL Internal PHY driver");
+MODULE_AUTHOR("Baoqi wang");
+MODULE_AUTHOR("Neil Armstrong <[email protected]>");
+MODULE_LICENSE("GPL");
--
1.9.1
In order to support PHY switching on Amlogic GXL SoCs, add support for
16bit and 32bit registers sizes.
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
---
.../devicetree/bindings/net/mdio-mux-mmioreg.txt | 4 +-
drivers/net/phy/mdio-mux-mmioreg.c | 60 +++++++++++++++++-----
2 files changed, 49 insertions(+), 15 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
index 8516929..065e8bd 100644
--- a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
+++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt
@@ -3,7 +3,7 @@ Properties for an MDIO bus multiplexer controlled by a memory-mapped device
This is a special case of a MDIO bus multiplexer. A memory-mapped device,
like an FPGA, is used to control which child bus is connected. The mdio-mux
node must be a child of the memory-mapped device. The driver currently only
-supports devices with eight-bit registers.
+supports devices with 8, 16 or 32-bit registers.
Required properties in addition to the generic multiplexer properties:
@@ -11,7 +11,7 @@ Required properties in addition to the generic multiplexer properties:
- reg : integer, contains the offset of the register that controls the bus
multiplexer. The size field in the 'reg' property is the size of
- register, and must therefore be 1.
+ register, and must therefore be 1, 2, or 4.
- mux-mask : integer, contains an eight-bit mask that specifies which
bits in the register control the actual bus multiplexer. The
diff --git a/drivers/net/phy/mdio-mux-mmioreg.c b/drivers/net/phy/mdio-mux-mmioreg.c
index d0bed52..6a33646 100644
--- a/drivers/net/phy/mdio-mux-mmioreg.c
+++ b/drivers/net/phy/mdio-mux-mmioreg.c
@@ -21,7 +21,8 @@
struct mdio_mux_mmioreg_state {
void *mux_handle;
phys_addr_t phys;
- uint8_t mask;
+ unsigned int iosize;
+ unsigned int mask;
};
/*
@@ -47,17 +48,47 @@ static int mdio_mux_mmioreg_switch_fn(int current_child, int desired_child,
struct mdio_mux_mmioreg_state *s = data;
if (current_child ^ desired_child) {
- void __iomem *p = ioremap(s->phys, 1);
- uint8_t x, y;
-
+ void __iomem *p = ioremap(s->phys, s->iosize);
if (!p)
return -ENOMEM;
- x = ioread8(p);
- y = (x & ~s->mask) | desired_child;
- if (x != y) {
- iowrite8((x & ~s->mask) | desired_child, p);
- pr_debug("%s: %02x -> %02x\n", __func__, x, y);
+ switch (s->iosize) {
+ case sizeof(uint8_t): {
+ uint8_t x, y;
+
+ x = ioread8(p);
+ y = (x & ~s->mask) | desired_child;
+ if (x != y) {
+ iowrite8((x & ~s->mask) | desired_child, p);
+ pr_debug("%s: %02x -> %02x\n", __func__, x, y);
+ }
+
+ break;
+ }
+ case sizeof(uint16_t): {
+ uint16_t x, y;
+
+ x = ioread16(p);
+ y = (x & ~s->mask) | desired_child;
+ if (x != y) {
+ iowrite16((x & ~s->mask) | desired_child, p);
+ pr_debug("%s: %04x -> %04x\n", __func__, x, y);
+ }
+
+ break;
+ }
+ case sizeof(uint32_t): {
+ uint32_t x, y;
+
+ x = ioread32(p);
+ y = (x & ~s->mask) | desired_child;
+ if (x != y) {
+ iowrite32((x & ~s->mask) | desired_child, p);
+ pr_debug("%s: %08x -> %08x\n", __func__, x, y);
+ }
+
+ break;
+ }
}
iounmap(p);
@@ -88,8 +119,11 @@ static int mdio_mux_mmioreg_probe(struct platform_device *pdev)
}
s->phys = res.start;
- if (resource_size(&res) != sizeof(uint8_t)) {
- dev_err(&pdev->dev, "only 8-bit registers are supported\n");
+ s->iosize = resource_size(&res);
+ if (s->iosize != sizeof(uint8_t) &&
+ s->iosize != sizeof(uint16_t) &&
+ s->iosize != sizeof(uint32_t)) {
+ dev_err(&pdev->dev, "only 8/16/32-bit registers are supported\n");
return -EINVAL;
}
@@ -98,8 +132,8 @@ static int mdio_mux_mmioreg_probe(struct platform_device *pdev)
dev_err(&pdev->dev, "missing or invalid mux-mask property\n");
return -ENODEV;
}
- if (be32_to_cpup(iprop) > 255) {
- dev_err(&pdev->dev, "only 8-bit registers are supported\n");
+ if (be32_to_cpup(iprop) >= BIT(s->iosize * 8)) {
+ dev_err(&pdev->dev, "only 8/16/32-bit registers are supported\n");
return -EINVAL;
}
s->mask = be32_to_cpup(iprop);
--
1.9.1
On 11/04/2016 08:51 AM, Neil Armstrong wrote:
> Add driver for the Internal RMII PHY found in the Amlogic Meson GXL SoCs.
>
> This PHY seems to only implement some standard registers and need some
> workarounds to provide autoneg values from vendor registers.
>
> Some magic values are currently used to configure the PHY, and this a
> temporary setup until clarification about these registers names and
> registers fields are provided by Amlogic.
>
> Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
--
Florian
On 11/04/2016 08:51 AM, Neil Armstrong wrote:
> In order to support PHY switching on Amlogic GXL SoCs, add support for
> 16bit and 32bit registers sizes.
>
> Reviewed-by: Andrew Lunn <[email protected]>
> Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
--
Florian
On Fri, Nov 04, 2016 at 04:51:23PM +0100, Neil Armstrong wrote:
> Add driver for the Internal RMII PHY found in the Amlogic Meson GXL SoCs.
>
> This PHY seems to only implement some standard registers and need some
> workarounds to provide autoneg values from vendor registers.
>
> Some magic values are currently used to configure the PHY, and this a
> temporary setup until clarification about these registers names and
> registers fields are provided by Amlogic.
>
> Signed-off-by: Neil Armstrong <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Andrew
From: Neil Armstrong <[email protected]>
Date: Fri, 4 Nov 2016 16:51:21 +0100
> The Amlogic Meson GXL SoCs have an internal RMII PHY that is muxed with the
> external RGMII pins.
>
> In order to support switching between the two PHYs links, extended registers
> size for mdio-mux-mmioreg must be added.
>
> The DT related patches submitted as RFC in [3] will be sent in a separate
> patchset due to multiple patchsets and DTSI migrations.
>
> Changes since v2 RFC patchset at : [3]
> - Change phy Kconfig/Makefile alphabetic order
> - GXL dtsi cleanup
>
> Changes since original RFC patchset at : [2]
> - Remove meson8b experimental phy switching
> - Switch to mdio-mux-mmioreg with extennded size support
> - Add internal phy support for S905x and p231
> - Add external PHY support for p230
>
> [1] http://lkml.kernel.org/r/[email protected]
> [2] http://lkml.kernel.org/r/[email protected]
> [3] http://lkml.kernel.org/r/[email protected]
Series applied, thanks.