Since there are SATA controllers that configure vendor specific registers
for AXI bus, OOB timing, threshold related settings. These settings may get
reset to the default values on resetting the SATA controller.
So this patch adds the support for adding [save|restore]_initial_config
override functions for saving and restoring controller values from the driver
instead of doing it in AHCI stack
Signed-off-by: Anurag Kumar Vulisha <[email protected]>
---
drivers/ata/ahci.c | 5 ++++-
drivers/ata/ahci.h | 9 +++++++++
drivers/ata/libahci.c | 5 ++++-
drivers/ata/libahci_platform.c | 5 ++++-
drivers/ata/sata_highbank.c | 6 ++++--
5 files changed, 25 insertions(+), 5 deletions(-)
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 2fc5240..ed76c9e 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -613,7 +613,10 @@ static void ahci_pci_save_initial_config(struct pci_dev *pdev,
"Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.\n");
}
- ahci_save_initial_config(&pdev->dev, hpriv);
+ if (hpriv->save_initial_config == NULL)
+ ahci_save_initial_config(dev, hpriv);
+ else
+ hpriv->save_initial_config(dev, hpriv);
}
static int ahci_pci_reset_controller(struct ata_host *host)
diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index 5db6ab2..2929e27 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -363,6 +363,15 @@ struct ahci_host_priv {
/* only required for per-port MSI(-X) support */
int (*get_irq_vector)(struct ata_host *host,
int port);
+
+ /*
+ * Optional ahci_save_initial_config & ahci_restore_initial_config
+ * override, if not set then default ahci_save_initial_config and
+ * ahci_restore_initial_config in libahci.c will be used
+ */
+ void (*save_initial_config)(struct device *dev,
+ struct ahci_host_priv *hpriv);
+ void (*restore_initial_config)(struct ata_host *host);
};
extern int ahci_ignore_sss;
diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c
index 3159f9e..fb57525 100644
--- a/drivers/ata/libahci.c
+++ b/drivers/ata/libahci.c
@@ -940,7 +940,10 @@ int ahci_reset_controller(struct ata_host *host)
/* Some registers might be cleared on reset. Restore
* initial values.
*/
- ahci_restore_initial_config(host);
+ if (hpriv->restore_initial_config == NULL)
+ ahci_restore_initial_config(host);
+ else
+ hpriv->restore_initial_config(host);
} else
dev_info(host->dev, "skipping global host reset\n");
diff --git a/drivers/ata/libahci_platform.c b/drivers/ata/libahci_platform.c
index aaa761b..15ba5f8 100644
--- a/drivers/ata/libahci_platform.c
+++ b/drivers/ata/libahci_platform.c
@@ -523,7 +523,10 @@ int ahci_platform_init_host(struct platform_device *pdev,
/* prepare host */
pi.private_data = (void *)(unsigned long)hpriv->flags;
- ahci_save_initial_config(dev, hpriv);
+ if (hpriv->save_initial_config == NULL)
+ ahci_save_initial_config(dev, hpriv);
+ else
+ hpriv->save_initial_config(dev, hpriv);
if (hpriv->cap & HOST_CAP_NCQ)
pi.flags |= ATA_FLAG_NCQ;
diff --git a/drivers/ata/sata_highbank.c b/drivers/ata/sata_highbank.c
index aafb8cc..61af3c6 100644
--- a/drivers/ata/sata_highbank.c
+++ b/drivers/ata/sata_highbank.c
@@ -512,8 +512,10 @@ static int ahci_highbank_probe(struct platform_device *pdev)
if (rc)
return rc;
-
- ahci_save_initial_config(dev, hpriv);
+ if (hpriv->save_initial_config == NULL)
+ ahci_save_initial_config(dev, hpriv);
+ else
+ hpriv->save_initial_config(dev, hpriv);
/* prepare host */
if (hpriv->cap & HOST_CAP_NCQ)
--
2.1.1
On Tue, Mar 14, 2017 at 05:29:21PM +0530, Anurag Kumar Vulisha wrote:
> @@ -613,7 +613,10 @@ static void ahci_pci_save_initial_config(struct pci_dev *pdev,
> "Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.\n");
> }
>
> - ahci_save_initial_config(&pdev->dev, hpriv);
> + if (hpriv->save_initial_config == NULL)
> + ahci_save_initial_config(dev, hpriv);
> + else
> + hpriv->save_initial_config(dev, hpriv);
Can you just initialize hpriv->save_initial_config to
ahci_save_initial_config and let the init function override it as
necessary?
Thanks.
--
tejun