2017-06-20 15:07:24

by Masahiro Yamada

Subject: [PATCH] clk: uniphier: provide NAND controller clock rate

This allows the NAND driver to get the clock rate via clk_get_rate().

Signed-off-by: Masahiro Yamada <[email protected]>
---

drivers/clk/uniphier/clk-uniphier-sys.c | 15 +++++++++++----
1 file changed, 11 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/uniphier/clk-uniphier-sys.c b/drivers/clk/uniphier/clk-uniphier-sys.c
index c8027d9..ad02181 100644
--- a/drivers/clk/uniphier/clk-uniphier-sys.c
+++ b/drivers/clk/uniphier/clk-uniphier-sys.c
@@ -29,11 +29,18 @@
UNIPHIER_CLK_FACTOR("sd-200m", -1, "spll", 1, 10), \
UNIPHIER_CLK_FACTOR("sd-133m", -1, "spll", 1, 15)

+/* Denali driver requires clk_x rate (clk: 50MHz, clk_x & ecc_clk: 200MHz) */
#define UNIPHIER_SLD3_SYS_CLK_NAND(idx) \
- UNIPHIER_CLK_GATE("nand", (idx), NULL, 0x2104, 2)
+ UNIPHIER_CLK_FACTOR("nand-200m", -1, "spll", 1, 8), \
+ UNIPHIER_CLK_GATE("nand", (idx), "nand-200m", 0x2104, 2)
+
+#define UNIPHIER_PRO5_SYS_CLK_NAND(idx) \
+ UNIPHIER_CLK_FACTOR("nand-200m", -1, "spll", 1, 12), \
+ UNIPHIER_CLK_GATE("nand", (idx), "nand-200m", 0x2104, 2)

#define UNIPHIER_LD11_SYS_CLK_NAND(idx) \
- UNIPHIER_CLK_GATE("nand", (idx), NULL, 0x210c, 0)
+ UNIPHIER_CLK_FACTOR("nand-200m", -1, "spll", 1, 10), \
+ UNIPHIER_CLK_GATE("nand", (idx), "nand-200m", 0x210c, 0)

#define UNIPHIER_LD11_SYS_CLK_EMMC(idx) \
UNIPHIER_CLK_GATE("emmc", (idx), NULL, 0x210c, 2)
@@ -114,7 +121,7 @@ const struct uniphier_clk_data uniphier_pro5_sys_clk_data[] = {
UNIPHIER_CLK_FACTOR("dapll2", -1, "ref", 144, 125), /* 2949.12 MHz */
UNIPHIER_CLK_FACTOR("uart", 0, "dapll2", 1, 40),
UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 48),
- UNIPHIER_SLD3_SYS_CLK_NAND(2),
+ UNIPHIER_PRO5_SYS_CLK_NAND(2),
UNIPHIER_PRO5_SYS_CLK_SD,
UNIPHIER_SLD3_SYS_CLK_STDMAC(8), /* HSC */
UNIPHIER_PRO4_SYS_CLK_GIO(12), /* PCIe, USB3 */
@@ -127,7 +134,7 @@ const struct uniphier_clk_data uniphier_pxs2_sys_clk_data[] = {
UNIPHIER_CLK_FACTOR("spll", -1, "ref", 96, 1), /* 2400 MHz */
UNIPHIER_CLK_FACTOR("uart", 0, "spll", 1, 27),
UNIPHIER_CLK_FACTOR("i2c", 1, "spll", 1, 48),
- UNIPHIER_SLD3_SYS_CLK_NAND(2),
+ UNIPHIER_PRO5_SYS_CLK_NAND(2),
UNIPHIER_PRO5_SYS_CLK_SD,
UNIPHIER_SLD3_SYS_CLK_STDMAC(8), /* HSC, RLE */
/* GIO is always clock-enabled: no function for 0x2104 bit6 */
--
2.7.4

2017-06-21 17:48:55

by Stephen Boyd

Subject: Re: [PATCH] clk: uniphier: provide NAND controller clock rate

On 06/21, Masahiro Yamada wrote:
> This allows the NAND driver to get the clock rate via clk_get_rate().
>
> Signed-off-by: Masahiro Yamada <[email protected]>
> ---

Applied to clk-next

--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project