These series of patches add companion_grf_quirk and otg_mux_irq_quirk for
rockchip usb2-phy. In addition, this change also add rv1108 usb2-phy support.
Changes from v1:
- Send the dt-bindings as a separate patch and cc devicetree list.
Frank Wang (5):
phy: rockchip-inno-usb2: add companion grf quirk
dt-bindings: phy-rockchip-inno-usb2: add companion grf quirk
phy: rockchip-inno-usb2: add otg mux irq quirk
dt-bindings: phy-rockchip-inno-usb2: add otg mux irq quirk
phy: rockchip-inno-usb2: add support of usb2-phy for rv1108 SoCs
.../bindings/phy/phy-rockchip-inno-usb2.txt | 10 +
drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 223 ++++++++++++++++-----
2 files changed, 182 insertions(+), 51 deletions(-)
--
2.0.0
Add rockchip,usbgrf and rockchip,companion_grf_quirk to support
the registers of usb-phy that are distributed in grf and usbgrf
on some special Rockchip SoCs (e.g RV1108).
Signed-off-by: Frank Wang <[email protected]>
---
Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
index 84d59b0..ddf868a 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
@@ -18,6 +18,10 @@ Optional properties:
usb-phy output 480m and xin24m.
Refer to clk/clock-bindings.txt for generic clock
consumer properties.
+ - rockchip,usbgrf : phandle to the syscon managing the "usb general
+ register files".
+ - rockchip,companion_grf_quirk : when set driver will request
+ "rockchip,usbgrf" phandle as one companion-grf.
Required nodes : a sub-node is required for each port the phy provides.
The sub-node name is used to identify host or otg port,
--
2.0.0
The otg-id/otg-bvalid/linestate irqs are multiplexed to one irq in
otg-port on some Rockchip SoCs (e.g RV1108), this patch add a quirk
to support this mux irq feature.
Signed-off-by: Frank Wang <[email protected]>
---
drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 68 ++++++++++++++++++++++-----
1 file changed, 55 insertions(+), 13 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
index 23a0652..bebf23f 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
@@ -172,6 +172,8 @@ struct rockchip_usb2phy_cfg {
* @vbus_attached: otg device vbus status.
* @bvalid_irq: IRQ number assigned for vbus valid rise detection.
* @ls_irq: IRQ number assigned for linestate detection.
+ * @otg_mux_irq: IRQ number which multiplex otg-id/otg-bvalid/linestate
+ * irqs to one irq in otg-port.
* @mutex: for register updating in sm_work.
* @chg_work: charge detect work.
* @otg_sm_work: OTG state machine work.
@@ -189,6 +191,7 @@ struct rockchip_usb2phy_port {
bool vbus_attached;
int bvalid_irq;
int ls_irq;
+ int otg_mux_irq;
struct mutex mutex;
struct delayed_work chg_work;
struct delayed_work otg_sm_work;
@@ -228,6 +231,7 @@ struct rockchip_usb2phy {
const struct rockchip_usb2phy_cfg *phy_cfg;
struct rockchip_usb2phy_port ports[USB2PHY_NUM_PORTS];
unsigned int companion_grf_quirk:1;
+ unsigned int otg_mux_irq_quirk:1;
};
static inline struct regmap *get_reg_base(struct rockchip_usb2phy *rphy)
@@ -935,6 +939,17 @@ static irqreturn_t rockchip_usb2phy_bvalid_irq(int irq, void *data)
return IRQ_HANDLED;
}
+static irqreturn_t rockchip_usb2phy_otg_mux_irq(int irq, void *data)
+{
+ struct rockchip_usb2phy_port *rport = data;
+ struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
+
+ if (property_enabled(rphy->grf, &rport->port_cfg->bvalid_det_st))
+ return rockchip_usb2phy_bvalid_irq(irq, data);
+ else
+ return IRQ_NONE;
+}
+
static int rockchip_usb2phy_host_port_init(struct rockchip_usb2phy *rphy,
struct rockchip_usb2phy_port *rport,
struct device_node *child_np)
@@ -1011,20 +1026,44 @@ static int rockchip_usb2phy_otg_port_init(struct rockchip_usb2phy *rphy,
rport->utmi_avalid =
of_property_read_bool(child_np, "rockchip,utmi-avalid");
- rport->bvalid_irq = of_irq_get_byname(child_np, "otg-bvalid");
- if (rport->bvalid_irq < 0) {
- dev_err(rphy->dev, "no vbus valid irq provided\n");
- ret = rport->bvalid_irq;
- goto out;
- }
+ if (rphy->otg_mux_irq_quirk) {
+ rport->otg_mux_irq = of_irq_get_byname(child_np, "otg-mux");
+ if (rport->otg_mux_irq < 0) {
+ dev_err(rphy->dev, "no otg-mux irq provided\n");
+ ret = rport->otg_mux_irq;
+ goto out;
+ }
- ret = devm_request_threaded_irq(rphy->dev, rport->bvalid_irq, NULL,
- rockchip_usb2phy_bvalid_irq,
- IRQF_ONESHOT,
- "rockchip_usb2phy_bvalid", rport);
- if (ret) {
- dev_err(rphy->dev, "failed to request otg-bvalid irq handle\n");
- goto out;
+ ret = devm_request_threaded_irq(rphy->dev, rport->otg_mux_irq,
+ NULL,
+ rockchip_usb2phy_otg_mux_irq,
+ IRQF_ONESHOT,
+ "rockchip_usb2phy_otg",
+ rport);
+ if (ret) {
+ dev_err(rphy->dev,
+ "failed to request otg-mux irq handle\n");
+ goto out;
+ }
+ } else {
+ rport->bvalid_irq = of_irq_get_byname(child_np, "otg-bvalid");
+ if (rport->bvalid_irq < 0) {
+ dev_err(rphy->dev, "no vbus valid irq provided\n");
+ ret = rport->bvalid_irq;
+ goto out;
+ }
+
+ ret = devm_request_threaded_irq(rphy->dev, rport->bvalid_irq,
+ NULL,
+ rockchip_usb2phy_bvalid_irq,
+ IRQF_ONESHOT,
+ "rockchip_usb2phy_bvalid",
+ rport);
+ if (ret) {
+ dev_err(rphy->dev,
+ "failed to request otg-bvalid irq handle\n");
+ goto out;
+ }
}
if (!IS_ERR(rphy->edev)) {
@@ -1081,6 +1120,9 @@ static int rockchip_usb2phy_probe(struct platform_device *pdev)
rphy->usbgrf = NULL;
}
+ rphy->otg_mux_irq_quirk =
+ device_property_read_bool(dev, "rockchip,otg_mux_irq_quirk");
+
if (of_property_read_u32(np, "reg", ®)) {
dev_err(dev, "the reg property is not assigned in %s node\n",
np->name);
--
2.0.0
Add rockchip,otg_mux_irq_quirk property to support the otg-id/
otg-bvalid/linestate irqs that are multiplexed to one irq in
otg-port on some special Rockchip SoCs (e.g RV1108).
Signed-off-by: Frank Wang <[email protected]>
---
Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
index ddf868a..d49572b 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
@@ -22,6 +22,8 @@ Optional properties:
register files".
- rockchip,companion_grf_quirk : when set driver will request
"rockchip,usbgrf" phandle as one companion-grf.
+ - rockchip,otg_mux_irq_quirk: set if otg-id/otg-bvalid/linestate irqs
+ are multiplexed to one irq in otg-port on some SoCs.
Required nodes : a sub-node is required for each port the phy provides.
The sub-node name is used to identify host or otg port,
@@ -36,6 +38,9 @@ Required properties (port (child) node):
* "otg-id" : for the otg id interrupt.
* "otg-bvalid" : for the otg vbus interrupt.
* "linestate" : for the host/otg linestate interrupt.
+ * "otg-mux" : otg-port interrupt, which multiplex otg-id/otg-bvalid/
+ linestate irqs to one irq. Should specify if
+ rockchip,otg_mux_irq_quirk property is set.
Optional properties:
- phy-supply : phandle to a regulator that provides power to VBUS.
--
2.0.0
The registers of usb-phy are distributed in grf and usbgrf on some
Rockchip SoCs (e.g RV1108), this patch add a quirk to support this
companion grf design.
Signed-off-by: Frank Wang <[email protected]>
---
drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 112 +++++++++++++++++---------
1 file changed, 74 insertions(+), 38 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
index 626883d..23a0652 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
@@ -202,6 +202,7 @@ struct rockchip_usb2phy_port {
/**
* struct rockchip_usb2phy: usb2.0 phy driver data.
* @grf: General Register Files regmap.
+ * @usbgrf: USB General Register Files regmap.
* @clk: clock struct of phy input clk.
* @clk480m: clock struct of phy output clk.
* @clk_hw: clock struct of phy output clk management.
@@ -216,6 +217,7 @@ struct rockchip_usb2phy_port {
struct rockchip_usb2phy {
struct device *dev;
struct regmap *grf;
+ struct regmap *usbgrf;
struct clk *clk;
struct clk *clk480m;
struct clk_hw clk480m_hw;
@@ -225,9 +227,15 @@ struct rockchip_usb2phy {
struct extcon_dev *edev;
const struct rockchip_usb2phy_cfg *phy_cfg;
struct rockchip_usb2phy_port ports[USB2PHY_NUM_PORTS];
+ unsigned int companion_grf_quirk:1;
};
-static inline int property_enable(struct rockchip_usb2phy *rphy,
+static inline struct regmap *get_reg_base(struct rockchip_usb2phy *rphy)
+{
+ return rphy->companion_grf_quirk ? rphy->usbgrf : rphy->grf;
+}
+
+static inline int property_enable(struct regmap *base,
const struct usb2phy_reg *reg, bool en)
{
unsigned int val, mask, tmp;
@@ -236,17 +244,17 @@ static inline int property_enable(struct rockchip_usb2phy *rphy,
mask = GENMASK(reg->bitend, reg->bitstart);
val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT);
- return regmap_write(rphy->grf, reg->offset, val);
+ return regmap_write(base, reg->offset, val);
}
-static inline bool property_enabled(struct rockchip_usb2phy *rphy,
+static inline bool property_enabled(struct regmap *base,
const struct usb2phy_reg *reg)
{
int ret;
unsigned int tmp, orig;
unsigned int mask = GENMASK(reg->bitend, reg->bitstart);
- ret = regmap_read(rphy->grf, reg->offset, &orig);
+ ret = regmap_read(base, reg->offset, &orig);
if (ret)
return false;
@@ -258,11 +266,12 @@ static int rockchip_usb2phy_clk480m_prepare(struct clk_hw *hw)
{
struct rockchip_usb2phy *rphy =
container_of(hw, struct rockchip_usb2phy, clk480m_hw);
+ struct regmap *base = get_reg_base(rphy);
int ret;
/* turn on 480m clk output if it is off */
- if (!property_enabled(rphy, &rphy->phy_cfg->clkout_ctl)) {
- ret = property_enable(rphy, &rphy->phy_cfg->clkout_ctl, true);
+ if (!property_enabled(base, &rphy->phy_cfg->clkout_ctl)) {
+ ret = property_enable(base, &rphy->phy_cfg->clkout_ctl, true);
if (ret)
return ret;
@@ -277,17 +286,19 @@ static void rockchip_usb2phy_clk480m_unprepare(struct clk_hw *hw)
{
struct rockchip_usb2phy *rphy =
container_of(hw, struct rockchip_usb2phy, clk480m_hw);
+ struct regmap *base = get_reg_base(rphy);
/* turn off 480m clk output */
- property_enable(rphy, &rphy->phy_cfg->clkout_ctl, false);
+ property_enable(base, &rphy->phy_cfg->clkout_ctl, false);
}
static int rockchip_usb2phy_clk480m_prepared(struct clk_hw *hw)
{
struct rockchip_usb2phy *rphy =
container_of(hw, struct rockchip_usb2phy, clk480m_hw);
+ struct regmap *base = get_reg_base(rphy);
- return property_enabled(rphy, &rphy->phy_cfg->clkout_ctl);
+ return property_enabled(base, &rphy->phy_cfg->clkout_ctl);
}
static unsigned long
@@ -409,13 +420,13 @@ static int rockchip_usb2phy_init(struct phy *phy)
if (rport->mode != USB_DR_MODE_HOST &&
rport->mode != USB_DR_MODE_UNKNOWN) {
/* clear bvalid status and enable bvalid detect irq */
- ret = property_enable(rphy,
+ ret = property_enable(rphy->grf,
&rport->port_cfg->bvalid_det_clr,
true);
if (ret)
goto out;
- ret = property_enable(rphy,
+ ret = property_enable(rphy->grf,
&rport->port_cfg->bvalid_det_en,
true);
if (ret)
@@ -429,11 +440,13 @@ static int rockchip_usb2phy_init(struct phy *phy)
}
} else if (rport->port_id == USB2PHY_PORT_HOST) {
/* clear linestate and enable linestate detect irq */
- ret = property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
+ ret = property_enable(rphy->grf,
+ &rport->port_cfg->ls_det_clr, true);
if (ret)
goto out;
- ret = property_enable(rphy, &rport->port_cfg->ls_det_en, true);
+ ret = property_enable(rphy->grf,
+ &rport->port_cfg->ls_det_en, true);
if (ret)
goto out;
@@ -449,6 +462,7 @@ static int rockchip_usb2phy_power_on(struct phy *phy)
{
struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
+ struct regmap *base = get_reg_base(rphy);
int ret;
dev_dbg(&rport->phy->dev, "port power on\n");
@@ -460,7 +474,7 @@ static int rockchip_usb2phy_power_on(struct phy *phy)
if (ret)
return ret;
- ret = property_enable(rphy, &rport->port_cfg->phy_sus, false);
+ ret = property_enable(base, &rport->port_cfg->phy_sus, false);
if (ret)
return ret;
@@ -475,6 +489,7 @@ static int rockchip_usb2phy_power_off(struct phy *phy)
{
struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
+ struct regmap *base = get_reg_base(rphy);
int ret;
dev_dbg(&rport->phy->dev, "port power off\n");
@@ -482,7 +497,7 @@ static int rockchip_usb2phy_power_off(struct phy *phy)
if (rport->suspended)
return 0;
- ret = property_enable(rphy, &rport->port_cfg->phy_sus, true);
+ ret = property_enable(base, &rport->port_cfg->phy_sus, true);
if (ret)
return ret;
@@ -526,11 +541,11 @@ static void rockchip_usb2phy_otg_sm_work(struct work_struct *work)
bool vbus_attach, sch_work, notify_charger;
if (rport->utmi_avalid)
- vbus_attach =
- property_enabled(rphy, &rport->port_cfg->utmi_avalid);
+ vbus_attach = property_enabled(rphy->grf,
+ &rport->port_cfg->utmi_avalid);
else
- vbus_attach =
- property_enabled(rphy, &rport->port_cfg->utmi_bvalid);
+ vbus_attach = property_enabled(rphy->grf,
+ &rport->port_cfg->utmi_bvalid);
sch_work = false;
notify_charger = false;
@@ -650,22 +665,28 @@ static const char *chg_to_string(enum power_supply_type chg_type)
static void rockchip_chg_enable_dcd(struct rockchip_usb2phy *rphy,
bool en)
{
- property_enable(rphy, &rphy->phy_cfg->chg_det.rdm_pdwn_en, en);
- property_enable(rphy, &rphy->phy_cfg->chg_det.idp_src_en, en);
+ struct regmap *base = get_reg_base(rphy);
+
+ property_enable(base, &rphy->phy_cfg->chg_det.rdm_pdwn_en, en);
+ property_enable(base, &rphy->phy_cfg->chg_det.idp_src_en, en);
}
static void rockchip_chg_enable_primary_det(struct rockchip_usb2phy *rphy,
bool en)
{
- property_enable(rphy, &rphy->phy_cfg->chg_det.vdp_src_en, en);
- property_enable(rphy, &rphy->phy_cfg->chg_det.idm_sink_en, en);
+ struct regmap *base = get_reg_base(rphy);
+
+ property_enable(base, &rphy->phy_cfg->chg_det.vdp_src_en, en);
+ property_enable(base, &rphy->phy_cfg->chg_det.idm_sink_en, en);
}
static void rockchip_chg_enable_secondary_det(struct rockchip_usb2phy *rphy,
bool en)
{
- property_enable(rphy, &rphy->phy_cfg->chg_det.vdm_src_en, en);
- property_enable(rphy, &rphy->phy_cfg->chg_det.idp_sink_en, en);
+ struct regmap *base = get_reg_base(rphy);
+
+ property_enable(base, &rphy->phy_cfg->chg_det.vdm_src_en, en);
+ property_enable(base, &rphy->phy_cfg->chg_det.idp_sink_en, en);
}
#define CHG_DCD_POLL_TIME (100 * HZ / 1000)
@@ -677,6 +698,7 @@ static void rockchip_chg_detect_work(struct work_struct *work)
struct rockchip_usb2phy_port *rport =
container_of(work, struct rockchip_usb2phy_port, chg_work.work);
struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
+ struct regmap *base = get_reg_base(rphy);
bool is_dcd, tmout, vout;
unsigned long delay;
@@ -687,7 +709,7 @@ static void rockchip_chg_detect_work(struct work_struct *work)
if (!rport->suspended)
rockchip_usb2phy_power_off(rport->phy);
/* put the controller in non-driving mode */
- property_enable(rphy, &rphy->phy_cfg->chg_det.opmode, false);
+ property_enable(base, &rphy->phy_cfg->chg_det.opmode, false);
/* Start DCD processing stage 1 */
rockchip_chg_enable_dcd(rphy, true);
rphy->chg_state = USB_CHG_STATE_WAIT_FOR_DCD;
@@ -696,7 +718,8 @@ static void rockchip_chg_detect_work(struct work_struct *work)
break;
case USB_CHG_STATE_WAIT_FOR_DCD:
/* get data contact detection status */
- is_dcd = property_enabled(rphy, &rphy->phy_cfg->chg_det.dp_det);
+ is_dcd = property_enabled(rphy->grf,
+ &rphy->phy_cfg->chg_det.dp_det);
tmout = ++rphy->dcd_retries == CHG_DCD_MAX_RETRIES;
/* stage 2 */
if (is_dcd || tmout) {
@@ -713,7 +736,8 @@ static void rockchip_chg_detect_work(struct work_struct *work)
}
break;
case USB_CHG_STATE_DCD_DONE:
- vout = property_enabled(rphy, &rphy->phy_cfg->chg_det.cp_det);
+ vout = property_enabled(rphy->grf,
+ &rphy->phy_cfg->chg_det.cp_det);
rockchip_chg_enable_primary_det(rphy, false);
if (vout) {
/* Voltage Source on DM, Probe on DP */
@@ -734,7 +758,8 @@ static void rockchip_chg_detect_work(struct work_struct *work)
}
break;
case USB_CHG_STATE_PRIMARY_DONE:
- vout = property_enabled(rphy, &rphy->phy_cfg->chg_det.dcp_det);
+ vout = property_enabled(rphy->grf,
+ &rphy->phy_cfg->chg_det.dcp_det);
/* Turn off voltage source */
rockchip_chg_enable_secondary_det(rphy, false);
if (vout)
@@ -748,7 +773,7 @@ static void rockchip_chg_detect_work(struct work_struct *work)
/* fall through */
case USB_CHG_STATE_DETECTED:
/* put the controller in normal mode */
- property_enable(rphy, &rphy->phy_cfg->chg_det.opmode, true);
+ property_enable(base, &rphy->phy_cfg->chg_det.opmode, true);
rockchip_usb2phy_otg_sm_work(&rport->otg_sm_work.work);
dev_info(&rport->phy->dev, "charger = %s\n",
chg_to_string(rphy->chg_type));
@@ -790,8 +815,7 @@ static void rockchip_usb2phy_sm_work(struct work_struct *work)
if (ret < 0)
goto next_schedule;
- ret = regmap_read(rphy->grf, rport->port_cfg->utmi_hstdet.offset,
- &uhd);
+ ret = regmap_read(rphy->grf, rport->port_cfg->utmi_hstdet.offset, &uhd);
if (ret < 0)
goto next_schedule;
@@ -845,8 +869,8 @@ static void rockchip_usb2phy_sm_work(struct work_struct *work)
* activate the linestate detection to get the next device
* plug-in irq.
*/
- property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
- property_enable(rphy, &rport->port_cfg->ls_det_en, true);
+ property_enable(rphy->grf, &rport->port_cfg->ls_det_clr, true);
+ property_enable(rphy->grf, &rport->port_cfg->ls_det_en, true);
/*
* we don't need to rearm the delayed work when the phy port
@@ -869,14 +893,14 @@ static irqreturn_t rockchip_usb2phy_linestate_irq(int irq, void *data)
struct rockchip_usb2phy_port *rport = data;
struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
- if (!property_enabled(rphy, &rport->port_cfg->ls_det_st))
+ if (!property_enabled(rphy->grf, &rport->port_cfg->ls_det_st))
return IRQ_NONE;
mutex_lock(&rport->mutex);
/* disable linestate detect irq and clear its status */
- property_enable(rphy, &rport->port_cfg->ls_det_en, false);
- property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
+ property_enable(rphy->grf, &rport->port_cfg->ls_det_en, false);
+ property_enable(rphy->grf, &rport->port_cfg->ls_det_clr, true);
mutex_unlock(&rport->mutex);
@@ -896,13 +920,13 @@ static irqreturn_t rockchip_usb2phy_bvalid_irq(int irq, void *data)
struct rockchip_usb2phy_port *rport = data;
struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
- if (!property_enabled(rphy, &rport->port_cfg->bvalid_det_st))
+ if (!property_enabled(rphy->grf, &rport->port_cfg->bvalid_det_st))
return IRQ_NONE;
mutex_lock(&rport->mutex);
/* clear bvalid detect irq pending status */
- property_enable(rphy, &rport->port_cfg->bvalid_det_clr, true);
+ property_enable(rphy->grf, &rport->port_cfg->bvalid_det_clr, true);
mutex_unlock(&rport->mutex);
@@ -1045,6 +1069,18 @@ static int rockchip_usb2phy_probe(struct platform_device *pdev)
if (IS_ERR(rphy->grf))
return PTR_ERR(rphy->grf);
+ rphy->companion_grf_quirk =
+ device_property_read_bool(dev, "rockchip,companion_grf_quirk");
+ if (rphy->companion_grf_quirk) {
+ rphy->usbgrf =
+ syscon_regmap_lookup_by_phandle(dev->of_node,
+ "rockchip,usbgrf");
+ if (IS_ERR(rphy->usbgrf))
+ return PTR_ERR(rphy->usbgrf);
+ } else {
+ rphy->usbgrf = NULL;
+ }
+
if (of_property_read_u32(np, "reg", ®)) {
dev_err(dev, "the reg property is not assigned in %s node\n",
np->name);
--
2.0.0
This adds support usb2-phy for rv1108 SoCs and amend phy Documentation.
Signed-off-by: Frank Wang <[email protected]>
---
.../bindings/phy/phy-rockchip-inno-usb2.txt | 1 +
drivers/phy/rockchip/phy-rockchip-inno-usb2.c | 43 ++++++++++++++++++++++
2 files changed, 44 insertions(+)
diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
index d49572b..1479dda 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
@@ -6,6 +6,7 @@ Required properties (phy (parent) node):
* "rockchip,rk3328-usb2phy"
* "rockchip,rk3366-usb2phy"
* "rockchip,rk3399-usb2phy"
+ * "rockchip,rv1108-usb2phy"
- reg : the address offset of grf for usb-phy configuration.
- #clock-cells : should be 0.
- clock-output-names : specify the 480m output clock name.
diff --git a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
index bebf23f..bd405f9 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
@@ -1405,11 +1405,54 @@ static const struct rockchip_usb2phy_cfg rk3399_phy_cfgs[] = {
{ /* sentinel */ }
};
+static const struct rockchip_usb2phy_cfg rv1108_phy_cfgs[] = {
+ {
+ .reg = 0x100,
+ .num_ports = 2,
+ .clkout_ctl = { 0x108, 4, 4, 1, 0 },
+ .port_cfgs = {
+ [USB2PHY_PORT_OTG] = {
+ .phy_sus = { 0x0100, 15, 0, 0, 0x1d1 },
+ .bvalid_det_en = { 0x0680, 3, 3, 0, 1 },
+ .bvalid_det_st = { 0x0690, 3, 3, 0, 1 },
+ .bvalid_det_clr = { 0x06a0, 3, 3, 0, 1 },
+ .ls_det_en = { 0x0680, 2, 2, 0, 1 },
+ .ls_det_st = { 0x0690, 2, 2, 0, 1 },
+ .ls_det_clr = { 0x06a0, 2, 2, 0, 1 },
+ .utmi_bvalid = { 0x0804, 10, 10, 0, 1 },
+ .utmi_ls = { 0x0804, 13, 12, 0, 1 },
+ },
+ [USB2PHY_PORT_HOST] = {
+ .phy_sus = { 0x0104, 15, 0, 0, 0x1d1 },
+ .ls_det_en = { 0x0680, 4, 4, 0, 1 },
+ .ls_det_st = { 0x0690, 4, 4, 0, 1 },
+ .ls_det_clr = { 0x06a0, 4, 4, 0, 1 },
+ .utmi_ls = { 0x0804, 9, 8, 0, 1 },
+ .utmi_hstdet = { 0x0804, 7, 7, 0, 1 }
+ }
+ },
+ .chg_det = {
+ .opmode = { 0x0100, 3, 0, 5, 1 },
+ .cp_det = { 0x0804, 1, 1, 0, 1 },
+ .dcp_det = { 0x0804, 0, 0, 0, 1 },
+ .dp_det = { 0x0804, 2, 2, 0, 1 },
+ .idm_sink_en = { 0x0108, 8, 8, 0, 1 },
+ .idp_sink_en = { 0x0108, 7, 7, 0, 1 },
+ .idp_src_en = { 0x0108, 9, 9, 0, 1 },
+ .rdm_pdwn_en = { 0x0108, 10, 10, 0, 1 },
+ .vdm_src_en = { 0x0108, 12, 12, 0, 1 },
+ .vdp_src_en = { 0x0108, 11, 11, 0, 1 },
+ },
+ },
+ { /* sentinel */ }
+};
+
static const struct of_device_id rockchip_usb2phy_dt_match[] = {
{ .compatible = "rockchip,rk3228-usb2phy", .data = &rk3228_phy_cfgs },
{ .compatible = "rockchip,rk3328-usb2phy", .data = &rk3328_phy_cfgs },
{ .compatible = "rockchip,rk3366-usb2phy", .data = &rk3366_phy_cfgs },
{ .compatible = "rockchip,rk3399-usb2phy", .data = &rk3399_phy_cfgs },
+ { .compatible = "rockchip,rv1108-usb2phy", .data = &rv1108_phy_cfgs },
{}
};
MODULE_DEVICE_TABLE(of, rockchip_usb2phy_dt_match);
--
2.0.0
Hi Frank,
Am Mittwoch, 2. August 2017, 15:53:09 CEST schrieb Frank Wang:
> Add rockchip,otg_mux_irq_quirk property to support the otg-id/
> otg-bvalid/linestate irqs that are multiplexed to one irq in
> otg-port on some special Rockchip SoCs (e.g RV1108).
>
> Signed-off-by: Frank Wang <[email protected]>
> ---
> Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git
> a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt index
> ddf868a..d49572b 100644
> --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
> @@ -22,6 +22,8 @@ Optional properties:
> register files".
> - rockchip,companion_grf_quirk : when set driver will request
> "rockchip,usbgrf" phandle as one companion-grf.
> + - rockchip,otg_mux_irq_quirk: set if otg-id/otg-bvalid/linestate irqs
> + are multiplexed to one irq in otg-port on some SoCs.
>
> Required nodes : a sub-node is required for each port the phy provides.
> The sub-node name is used to identify host or otg port,
> @@ -36,6 +38,9 @@ Required properties (port (child) node):
> * "otg-id" : for the otg id interrupt.
> * "otg-bvalid" : for the otg vbus interrupt.
> * "linestate" : for the host/otg linestate interrupt.
> + * "otg-mux" : otg-port interrupt, which multiplex otg-id/otg-bvalid/
> + linestate irqs to one irq. Should specify if
> + rockchip,otg_mux_irq_quirk property is set.
I'd think that should be auto-detectable in the driver without the quirk
property above?
I.e. check for the otg-mux interrupt first on probe and if can be found, you
know that this is the case, otherwise look for the regular interrupts.
Also I would write that down a bit differently, so that it doesn't confuse
people. Something similar to:
- interrupt-names : a list which should
+ Regular case:
* "otg-id" : for the otg id interrupt.
* "otg-bvalid" : for the otg vbus interrupt.
* "linestate" : for the host/otg linestate interrupt.
+ Some socs use one interrupt with the obove muxed together, so for these
+ * "otg-mux" : otg-port interrupt, which multiplex otg-id/otg-bvalid/
+ linestate irqs to one irq.
Heiko
Hi Heiko,
On 2017/8/2 19:25, Heiko Stübner wrote:
> Hi Frank,
>
> Am Mittwoch, 2. August 2017, 15:53:09 CEST schrieb Frank Wang:
>> Add rockchip,otg_mux_irq_quirk property to support the otg-id/
>> otg-bvalid/linestate irqs that are multiplexed to one irq in
>> otg-port on some special Rockchip SoCs (e.g RV1108).
>>
>> Signed-off-by: Frank Wang <[email protected]>
>> ---
>> Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt | 5 +++++
>> 1 file changed, 5 insertions(+)
>>
>> diff --git
>> a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>> b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt index
>> ddf868a..d49572b 100644
>> --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt
>> @@ -22,6 +22,8 @@ Optional properties:
>> register files".
>> - rockchip,companion_grf_quirk : when set driver will request
>> "rockchip,usbgrf" phandle as one companion-grf.
>> + - rockchip,otg_mux_irq_quirk: set if otg-id/otg-bvalid/linestate irqs
>> + are multiplexed to one irq in otg-port on some SoCs.
>>
>> Required nodes : a sub-node is required for each port the phy provides.
>> The sub-node name is used to identify host or otg port,
>> @@ -36,6 +38,9 @@ Required properties (port (child) node):
>> * "otg-id" : for the otg id interrupt.
>> * "otg-bvalid" : for the otg vbus interrupt.
>> * "linestate" : for the host/otg linestate interrupt.
>> + * "otg-mux" : otg-port interrupt, which multiplex otg-id/otg-bvalid/
>> + linestate irqs to one irq. Should specify if
>> + rockchip,otg_mux_irq_quirk property is set.
> I'd think that should be auto-detectable in the driver without the quirk
> property above?
>
> I.e. check for the otg-mux interrupt first on probe and if can be found, you
> know that this is the case, otherwise look for the regular interrupts.
>
>
> Also I would write that down a bit differently, so that it doesn't confuse
> people. Something similar to:
>
> - interrupt-names : a list which should
> + Regular case:
> * "otg-id" : for the otg id interrupt.
> * "otg-bvalid" : for the otg vbus interrupt.
> * "linestate" : for the host/otg linestate interrupt.
> + Some socs use one interrupt with the obove muxed together, so for these
> + * "otg-mux" : otg-port interrupt, which multiplex otg-id/otg-bvalid/
> + linestate irqs to one irq.
>
>
> Heiko
>
Thanks for your comments, I will fix it in next version.
BR.
Frank