From: John Crispin <[email protected]>
Add a driver to setup the USB phy on Mediatek/Ralink SoCs.
The driver sets up power and host mode, but also needs to
configure PHY registers for the MT7628 and MT7688.
Signed-off-by: John Crispin <[email protected]>
Signed-off-by: Harvey Hunt <[email protected]>
Cc: [email protected]
Cc: [email protected]
---
Changes in V7
* Create ralink sub directory
* Switch from io{read,write}32 to {read,write}l
* Update copyright year
* Remove MIPS specific header
* Use regmap to access sysctl registers
* Parse syscon phandle to get regmap
* Select CONFIG_MFD_SYSCON
* Remove depends on MIPS
* Rearrange probe function
Changes in V6
* Add binding for MT7628
* Configure PHY registers for MT76{2,8}8
Changes in V5
* Depend on MIPS
Changes in V4
* Remove Allwinner from comment
* Depend on COMPILE_TEST
Changes in V3
* Separate DT bindings
* Update Kconfig text
* Modify John's email address
* Rebase onto v4.13-rc3
Changes in V2
* remove refcounting
* drop empty functions
* dont use static globals
* use explicit compatible strings
drivers/phy/Kconfig | 1 +
drivers/phy/Makefile | 1 +
drivers/phy/ralink/Kconfig | 11 ++
drivers/phy/ralink/Makefile | 1 +
drivers/phy/ralink/phy-ralink-usb.c | 249 ++++++++++++++++++++++++++++++++++++
5 files changed, 263 insertions(+)
create mode 100644 drivers/phy/ralink/Kconfig
create mode 100644 drivers/phy/ralink/Makefile
create mode 100644 drivers/phy/ralink/phy-ralink-usb.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index c1807d4..3792fd7 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -55,6 +55,7 @@ source "drivers/phy/hisilicon/Kconfig"
source "drivers/phy/marvell/Kconfig"
source "drivers/phy/motorola/Kconfig"
source "drivers/phy/qualcomm/Kconfig"
+source "drivers/phy/ralink/Kconfig"
source "drivers/phy/renesas/Kconfig"
source "drivers/phy/rockchip/Kconfig"
source "drivers/phy/samsung/Kconfig"
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index f252201..db9174d 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -18,6 +18,7 @@ obj-y += broadcom/ \
marvell/ \
motorola/ \
qualcomm/ \
+ ralink/ \
samsung/ \
st/ \
ti/
diff --git a/drivers/phy/ralink/Kconfig b/drivers/phy/ralink/Kconfig
new file mode 100644
index 0000000..b17635b
--- /dev/null
+++ b/drivers/phy/ralink/Kconfig
@@ -0,0 +1,11 @@
+#
+# PHY drivers for Ralink platforms.
+#
+config PHY_RALINK_USB
+ tristate "Ralink USB PHY driver"
+ depends on RALINK || COMPILE_TEST
+ select GENERIC_PHY
+ select MFD_SYSCON
+ help
+ This option enables support for the Ralink USB PHY found inside
+ RT3352, MT7620, MT7628 and MT7688.
diff --git a/drivers/phy/ralink/Makefile b/drivers/phy/ralink/Makefile
new file mode 100644
index 0000000..5c9e326
--- /dev/null
+++ b/drivers/phy/ralink/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_PHY_RALINK_USB) += phy-ralink-usb.o
diff --git a/drivers/phy/ralink/phy-ralink-usb.c b/drivers/phy/ralink/phy-ralink-usb.c
new file mode 100644
index 0000000..cade326
--- /dev/null
+++ b/drivers/phy/ralink/phy-ralink-usb.c
@@ -0,0 +1,249 @@
+/*
+ * Copyright (C) 2017 John Crispin <[email protected]>
+ *
+ * Based on code from
+ * Allwinner Technology Co., Ltd. <http://www.allwinnertech.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#define RT_SYSC_REG_SYSCFG1 0x014
+#define RT_SYSC_REG_CLKCFG1 0x030
+#define RT_SYSC_REG_USB_PHY_CFG 0x05c
+
+#define OFS_U2_PHY_AC0 0x800
+#define OFS_U2_PHY_AC1 0x804
+#define OFS_U2_PHY_AC2 0x808
+#define OFS_U2_PHY_ACR0 0x810
+#define OFS_U2_PHY_ACR1 0x814
+#define OFS_U2_PHY_ACR2 0x818
+#define OFS_U2_PHY_ACR3 0x81C
+#define OFS_U2_PHY_ACR4 0x820
+#define OFS_U2_PHY_AMON0 0x824
+#define OFS_U2_PHY_DCR0 0x860
+#define OFS_U2_PHY_DCR1 0x864
+#define OFS_U2_PHY_DTM0 0x868
+#define OFS_U2_PHY_DTM1 0x86C
+
+#define RT_RSTCTRL_UDEV BIT(25)
+#define RT_RSTCTRL_UHST BIT(22)
+#define RT_SYSCFG1_USB0_HOST_MODE BIT(10)
+
+#define MT7620_CLKCFG1_UPHY0_CLK_EN BIT(25)
+#define MT7620_CLKCFG1_UPHY1_CLK_EN BIT(22)
+#define RT_CLKCFG1_UPHY1_CLK_EN BIT(20)
+#define RT_CLKCFG1_UPHY0_CLK_EN BIT(18)
+
+#define USB_PHY_UTMI_8B60M BIT(1)
+#define UDEV_WAKEUP BIT(0)
+
+struct ralink_usb_phy {
+ struct reset_control *rstdev;
+ struct reset_control *rsthost;
+ u32 clk;
+ struct phy *phy;
+ void __iomem *base;
+ struct regmap *sysctl;
+};
+
+static void u2_phy_w32(struct ralink_usb_phy *phy, u32 val, u32 reg)
+{
+ writel(val, phy->base + reg);
+}
+
+static u32 u2_phy_r32(struct ralink_usb_phy *phy, u32 reg)
+{
+ return readl(phy->base + reg);
+}
+
+static void ralink_usb_phy_init(struct ralink_usb_phy *phy)
+{
+ u2_phy_r32(phy, OFS_U2_PHY_AC2);
+ u2_phy_r32(phy, OFS_U2_PHY_ACR0);
+ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+
+ u2_phy_w32(phy, 0x00ffff02, OFS_U2_PHY_DCR0);
+ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+ u2_phy_w32(phy, 0x00555502, OFS_U2_PHY_DCR0);
+ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+ u2_phy_w32(phy, 0x00aaaa02, OFS_U2_PHY_DCR0);
+ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+ u2_phy_w32(phy, 0x00000402, OFS_U2_PHY_DCR0);
+ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+ u2_phy_w32(phy, 0x0048086a, OFS_U2_PHY_AC0);
+ u2_phy_w32(phy, 0x4400001c, OFS_U2_PHY_AC1);
+ u2_phy_w32(phy, 0xc0200000, OFS_U2_PHY_ACR3);
+ u2_phy_w32(phy, 0x02000000, OFS_U2_PHY_DTM0);
+}
+
+static int ralink_usb_phy_power_on(struct phy *_phy)
+{
+ struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
+ u32 t;
+
+ /* enable the phy */
+ regmap_update_bits(phy->sysctl, RT_SYSC_REG_CLKCFG1,
+ phy->clk, phy->clk);
+
+ /* setup host mode */
+ regmap_update_bits(phy->sysctl, RT_SYSC_REG_SYSCFG1,
+ RT_SYSCFG1_USB0_HOST_MODE,
+ RT_SYSCFG1_USB0_HOST_MODE);
+
+ /* deassert the reset lines */
+ reset_control_deassert(phy->rsthost);
+ reset_control_deassert(phy->rstdev);
+
+ /*
+ * The SDK kernel had a delay of 100ms. however on device
+ * testing showed that 10ms is enough
+ */
+ mdelay(10);
+
+ if (phy->base)
+ ralink_usb_phy_init(phy);
+
+ /* print some status info */
+ regmap_read(phy->sysctl, RT_SYSC_REG_USB_PHY_CFG, &t);
+ dev_info(&phy->phy->dev, "remote usb device wakeup %s\n",
+ (t & UDEV_WAKEUP) ? ("enabled") : ("disabled"));
+ if (t & USB_PHY_UTMI_8B60M)
+ dev_info(&phy->phy->dev, "UTMI 8bit 60MHz\n");
+ else
+ dev_info(&phy->phy->dev, "UTMI 16bit 30MHz\n");
+
+ return 0;
+}
+
+static int ralink_usb_phy_power_off(struct phy *_phy)
+{
+ struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
+
+ /* disable the phy */
+ regmap_update_bits(phy->sysctl, RT_SYSC_REG_CLKCFG1,
+ phy->clk, 0);
+
+ /* assert the reset lines */
+ reset_control_assert(phy->rstdev);
+ reset_control_assert(phy->rsthost);
+
+ return 0;
+}
+
+static struct phy_ops ralink_usb_phy_ops = {
+ .power_on = ralink_usb_phy_power_on,
+ .power_off = ralink_usb_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static const struct of_device_id ralink_usb_phy_of_match[] = {
+ {
+ .compatible = "ralink,rt3352-usbphy",
+ .data = (void *) (RT_CLKCFG1_UPHY1_CLK_EN |
+ RT_CLKCFG1_UPHY0_CLK_EN)
+ },
+ {
+ .compatible = "mediatek,mt7620-usbphy",
+ .data = (void *) (MT7620_CLKCFG1_UPHY1_CLK_EN |
+ MT7620_CLKCFG1_UPHY0_CLK_EN)
+ },
+ {
+ .compatible = "mediatek,mt7628-usbphy",
+ .data = (void *) (MT7620_CLKCFG1_UPHY1_CLK_EN |
+ MT7620_CLKCFG1_UPHY0_CLK_EN) },
+ { },
+};
+MODULE_DEVICE_TABLE(of, ralink_usb_phy_of_match);
+
+static int ralink_usb_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct phy_provider *phy_provider;
+ const struct of_device_id *match;
+ struct ralink_usb_phy *phy;
+
+ match = of_match_device(ralink_usb_phy_of_match, &pdev->dev);
+ if (!match)
+ return -ENODEV;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->clk = (int) match->data;
+ phy->base = NULL;
+
+ phy->sysctl = syscon_regmap_lookup_by_phandle(dev->of_node, "ralink,sysctl");
+ if (IS_ERR(phy->sysctl)) {
+ dev_err(dev, "failed to get sysctl registers\n");
+ return PTR_ERR(phy->sysctl);
+ }
+
+ /* The MT7628 and MT7688 require extra setup of PHY registers. */
+ if (of_device_is_compatible(dev->of_node, "mediatek,mt7628-usbphy")) {
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ phy->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(phy->base)) {
+ dev_err(dev, "failed to remap register memory\n");
+ return PTR_ERR(phy->base);
+ }
+ }
+
+ phy->rsthost = devm_reset_control_get(&pdev->dev, "host");
+ if (IS_ERR(phy->rsthost)) {
+ dev_err(dev, "host reset is missing\n");
+ return PTR_ERR(phy->rsthost);
+ }
+
+ phy->rstdev = devm_reset_control_get(&pdev->dev, "device");
+ if (IS_ERR(phy->rstdev)) {
+ dev_err(dev, "device reset is missing\n");
+ return PTR_ERR(phy->rstdev);
+ }
+
+ phy->phy = devm_phy_create(dev, NULL, &ralink_usb_phy_ops);
+ if (IS_ERR(phy->phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(phy->phy);
+ }
+ phy_set_drvdata(phy->phy, phy);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver ralink_usb_phy_driver = {
+ .probe = ralink_usb_phy_probe,
+ .driver = {
+ .of_match_table = ralink_usb_phy_of_match,
+ .name = "ralink-usb-phy",
+ }
+};
+module_platform_driver(ralink_usb_phy_driver);
+
+MODULE_DESCRIPTION("Ralink USB phy driver");
+MODULE_AUTHOR("John Crispin <[email protected]>");
+MODULE_LICENSE("GPL v2");
--
2.7.4
From: John Crispin <[email protected]>
Add a binding for the USB phy on Mediatek/Ralink SoCs.
Signed-off-by: John Crispin <[email protected]>
Signed-off-by: Harvey Hunt <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
Changes in V7:
* Add required ralink,sysctl property
Changes in V6:
* Add MT7628 binding
* Add optional reg property
Changes in V5:
* None
Changes in V4:
* None
Changes in V3:
* Split out from first patch
.../devicetree/bindings/phy/ralink-usb-phy.txt | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt b/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
new file mode 100644
index 0000000..9d2868a
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
@@ -0,0 +1,23 @@
+Mediatek/Ralink USB PHY
+
+Required properties:
+ - compatible: "ralink,rt3352-usbphy"
+ "mediatek,mt7620-usbphy"
+ "mediatek,mt7628-usbphy"
+ - reg: required for "mediatek,mt7628-usbphy", unused otherwise
+ - #phy-cells: should be 0
+ - ralink,sysctl: a phandle to a ralink syscon register region
+ - resets: the two reset controllers for host and device
+ - reset-names: the names of the 2 reset controllers
+
+Example:
+
+usbphy: phy {
+ compatible = "mediatek,mt7628-usbphy";
+ reg = <0x10120000 0x1000>;
+ #phy-cells = <0>;
+
+ ralink,sysctl = <&sysc>;
+ resets = <&rstctrl 22 &rstctrl 25>;
+ reset-names = "host", "device";
+};
--
2.7.4
On Thursday 17 August 2017 04:03 PM, Harvey Hunt wrote:
> From: John Crispin <[email protected]>
>
> Add a binding for the USB phy on Mediatek/Ralink SoCs.
>
> Signed-off-by: John Crispin <[email protected]>
> Signed-off-by: Harvey Hunt <[email protected]>
> Cc: [email protected]
> Cc: [email protected]
> Cc: [email protected]
merged the series, thanks!
-Kishon
> ---
> Changes in V7:
> * Add required ralink,sysctl property
>
> Changes in V6:
> * Add MT7628 binding
> * Add optional reg property
>
> Changes in V5:
> * None
>
> Changes in V4:
> * None
>
> Changes in V3:
> * Split out from first patch
>
> .../devicetree/bindings/phy/ralink-usb-phy.txt | 23 ++++++++++++++++++++++
> 1 file changed, 23 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
>
> diff --git a/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt b/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
> new file mode 100644
> index 0000000..9d2868a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
> @@ -0,0 +1,23 @@
> +Mediatek/Ralink USB PHY
> +
> +Required properties:
> + - compatible: "ralink,rt3352-usbphy"
> + "mediatek,mt7620-usbphy"
> + "mediatek,mt7628-usbphy"
> + - reg: required for "mediatek,mt7628-usbphy", unused otherwise
> + - #phy-cells: should be 0
> + - ralink,sysctl: a phandle to a ralink syscon register region
> + - resets: the two reset controllers for host and device
> + - reset-names: the names of the 2 reset controllers
> +
> +Example:
> +
> +usbphy: phy {
> + compatible = "mediatek,mt7628-usbphy";
> + reg = <0x10120000 0x1000>;
> + #phy-cells = <0>;
> +
> + ralink,sysctl = <&sysc>;
> + resets = <&rstctrl 22 &rstctrl 25>;
> + reset-names = "host", "device";
> +};
>