When a need raise up to use JTAG interface for system's devices
programming or CPU debugging, usually the user layer
application implements jtag protocol by bit-bang or using a
proprietary connection to vendor hardware.
This method can be slow and not generic.
We propose to implement general JTAG interface and infrastructure
to communicate with user layer application. In such way, we can
have the standard JTAG interface core part and separation from
specific HW implementation.
This allow new capability to debug the CPU or program system's
device via BMC without additional devices nor cost.
This patch purpose is to add JTAG master core infrastructure by
defining new JTAG class and provide generic JTAG interface
to allow hardware specific drivers to connect this interface.
This will enable all JTAG drivers to use the common interface
part and will have separate for hardware implementation.
The JTAG (Joint Test Action Group) core driver provides minimal generic
JTAG interface, which can be used by hardware specific JTAG master
controllers. By providing common interface for the JTAG controllers,
user space device programing is hardware independent.
Modern SoC which in use for embedded system' equipped with
internal JTAG master interface.
This interface is used for programming and debugging system's
hardware components, like CPLD, FPGA, CPU, voltage and
industrial controllers.
Firmware for such devices can be upgraded through JTAG interface during
Runtime. The JTAG standard support for multiple devices programming,
is in case their lines are daisy-chained together.
For example, systems which equipped with host CPU, BMC SoC or/and
number of programmable devices are capable to connect a pin and
select system components dynamically for programming and debugging,
This is using by the BMC which is equipped with internal SoC master
controller.
For example:
BMC JTAG master --> pin selected to CPLDs chain for programming (filed
upgrade, production)
BMC JTAG master --> pin selected to voltage monitors for programming
(field upgrade, production)
BMC JTAG master --> pin selected to host CPU (on-site debugging
and developers debugging)
For example, we can have application in user space which using calls
to JTAG driver executes CPLD programming directly from SVF file
The JTAG standard (IEEE 1149.1) defines the next connector pins:
- TDI (Test Data In);
- TDO (Test Data Out);
- TCK (Test Clock);
- TMS (Test Mode Select);
- TRST (Test Reset) (Optional);
The SoC equipped with JTAG master controller, performs
device programming on command or vector level. For example
a file in a standard SVF (Serial Vector Format) that contains
boundary scan vectors, can be used by sending each vector
to the JTAG interface and the JTAG controller will execute
the programming.
Initial version provides the system calls set for:
- SIR (Scan Instruction Register, IEEE 1149.1 Data Register scan);
- SDR (Scan Data Register, IEEE 1149.1 Instruction Register scan);
- RUNTEST (Forces the IEEE 1149.1 bus to a run state for a specified
number of clocks.
SoC which are not equipped with JTAG master interface, can be built
on top of JTAG core driver infrastructure, by applying bit-banging of
TDI, TDO, TCK and TMS pins within the hardware specific driver.
Oleksandr Shamray (4):
drivers: jtag: Add JTAG core driver
drivers: jtag: Add Aspeed SoC 24xx and 25xx families JTAG master
driver
Documentation: jtag: Add bindings for Aspeed SoC 24xx and 25xx
families JTAG master driver
Documentation: jtag: Add ABI documentation
Documentation/ABI/testing/jtag-dev | 27 +
.../devicetree/bindings/jtag/aspeed-jtag.txt | 18 +
Documentation/ioctl/ioctl-number.txt | 2 +
MAINTAINERS | 10 +
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/jtag/Kconfig | 29 +
drivers/jtag/Makefile | 2 +
drivers/jtag/jtag-aspeed.c | 782 ++++++++++++++++++++
drivers/jtag/jtag.c | 292 ++++++++
include/linux/jtag.h | 46 ++
include/uapi/linux/jtag.h | 105 +++
12 files changed, 1316 insertions(+), 0 deletions(-)
create mode 100644 Documentation/ABI/testing/jtag-dev
create mode 100644 Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
create mode 100644 drivers/jtag/Kconfig
create mode 100644 drivers/jtag/Makefile
create mode 100644 drivers/jtag/jtag-aspeed.c
create mode 100644 drivers/jtag/jtag.c
create mode 100644 include/linux/jtag.h
create mode 100644 include/uapi/linux/jtag.h
From 1583349232603917080@xxx Mon Nov 06 20:18:17 +0000 2017
X-GM-THRID: 1582902877322165890
X-Gmail-Labels: Inbox,Category Forums,HistoricalUnread
Initial patch for JTAG driver
JTAG class driver provide infrastructure to support hardware/software
JTAG platform drivers. It provide user layer API interface for flashing
and debugging external devices which equipped with JTAG interface
using standard transactions.
Driver exposes set of IOCTL to user space for:
- XFER:
- SIR (Scan Instruction Register, IEEE 1149.1 Data Register scan);
- SDR (Scan Data Register, IEEE 1149.1 Instruction Register scan);
- RUNTEST (Forces the IEEE 1149.1 bus to a run state for a specified
number of clocks).
- SIOCFREQ/GIOCFREQ for setting and reading JTAG frequency.
Driver core provides set of internal APIs for allocation and
registration:
- jtag_register;
- jtag_unregister;
- jtag_alloc;
- jtag_free;
Platform driver on registration with jtag-core creates the next
entry in dev folder:
/dev/jtagX
Signed-off-by: Oleksandr Shamray <[email protected]>
Signed-off-by: Jiri Pirko <[email protected]>
---
v11->v12
Comments pointed by Greg KH <[email protected]>
- Change jtag.h licence type to
SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note
and reorder line with license in description
Chip Bilbrey <[email protected]>
- Remove Apeed reference from uapi jtag.h header
- Remove access mode from xfer and idle transactions
- Add new ioctl JTAG_SIOCMODE for set hw mode
- Add only one open per JTAG port blocking with mutex blocking
v10->v11
Notifications from kbuild test robot <[email protected]>
- include types.h headeri to jtag.h
- fix incompatible type of xfer callback
- remove rdundant class defination
- Fix return order in case of xfer error
V9->v10
Comments pointed by Greg KH <[email protected]>
- remove unnecessary alignment for pirv data
- move jtag_copy_to_user and jtag_copy_from_user code just to ioctl
- move int jtag_run_test_idle_op and jtag_xfer_op code
just to ioctl
- change return error codes to more applicable
- add missing error checks
- fix error check order in ioctl
- remove unnecessary blank lines
- add param validation to ioctl
- remove compat_ioctl
- remove only one open per JTAG port blocking.
User will care about this.
- Fix idr memory leak on jtag_exit
- change cdev device type to misc
V8->v9
Comments pointed by Arnd Bergmann <[email protected]>
- use get_user() instead of __get_user().
- change jtag->open type from int to atomic_t
- remove spinlock on jtg_open
- remove mutex on jtag_register
- add unregister_chrdev_region on jtag_init err
- add unregister_chrdev_region on jtag_exit
- remove unnecessary pointer casts
- add *data parameter to xfer function prototype
v7->v8
Comments pointed by Moritz Fischer <[email protected]>
- Fix misspelling s/friver/driver
v6->v7
Notifications from kbuild test robot <[email protected]>
- Remove include asm/types.h from jtag.h
- Add include <linux/types.h> to jtag.c
v5->v6
v4->v5
v3->v4
Comments pointed by Arnd Bergmann <[email protected]>
- change transaction pointer tdio type to __u64
- change internal status type from enum to __u32
- reorder jtag_xfer members to avoid the implied padding
- add __packed attribute to jtag_xfer and jtag_run_test_idle
v2->v3
Notifications from kbuild test robot <[email protected]>
- Change include path to <linux/types.h> in jtag.h
v1->v2
Comments pointed by Greg KH <[email protected]>
- Change license type from GPLv2/BSD to GPLv2
- Change type of variables which crossed user/kernel to __type
- Remove "default n" from Kconfig
Comments pointed by Andrew Lunn <[email protected]>
- Change list_add_tail in jtag_unregister to list_del
Comments pointed by Neil Armstrong <[email protected]>
- Add SPDX-License-Identifier instead of license text
Comments pointed by Arnd Bergmann <[email protected]>
- Change __copy_to_user to memdup_user
- Change __put_user to put_user
- Change type of variables to __type for compatible 32 and 64-bit systems
- Add check for maximum xfer data size
- Change lookup data mechanism to get jtag data from inode
- Add .compat_ioctl to file ops
- Add mem alignment for jtag priv data
Comments pointed by Tobias Klauser <[email protected]>
- Change function names to avoid match with variable types
- Fix description for jtag_ru_test_idle in uapi jtag.h
- Fix misprints IDEL/IDLE, trough/through
---
Documentation/ioctl/ioctl-number.txt | 2 +
MAINTAINERS | 10 ++
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/jtag/Kconfig | 16 ++
drivers/jtag/Makefile | 1 +
drivers/jtag/jtag.c | 292 ++++++++++++++++++++++++++++++++++
include/linux/jtag.h | 46 ++++++
include/uapi/linux/jtag.h | 105 ++++++++++++
9 files changed, 475 insertions(+), 0 deletions(-)
create mode 100644 drivers/jtag/Kconfig
create mode 100644 drivers/jtag/Makefile
create mode 100644 drivers/jtag/jtag.c
create mode 100644 include/linux/jtag.h
create mode 100644 include/uapi/linux/jtag.h
diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt
index 3e3fdae..1af2508 100644
--- a/Documentation/ioctl/ioctl-number.txt
+++ b/Documentation/ioctl/ioctl-number.txt
@@ -321,6 +321,8 @@ Code Seq#(hex) Include File Comments
0xB0 all RATIO devices in development:
<mailto:[email protected]>
0xB1 00-1F PPPoX <mailto:[email protected]>
+0xB2 00-0f linux/jtag.h JTAG driver
+ <mailto:[email protected]>
0xB3 00 linux/mmc/ioctl.h
0xB4 00-0F linux/gpio.h <mailto:[email protected]>
0xB5 00-0F uapi/linux/rpmsg.h <mailto:[email protected]>
diff --git a/MAINTAINERS b/MAINTAINERS
index 205d397..dfcf49c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7292,6 +7292,16 @@ L: [email protected]
S: Maintained
F: drivers/tty/serial/jsm/
+JTAG SUBSYSTEM
+M: Oleksandr Shamray <[email protected]>
+M: Vadim Pasternak <[email protected]>
+S: Maintained
+F: include/linux/jtag.h
+F: include/uapi/linux/jtag.h
+F: drivers/jtag/
+F: Documentation/devicetree/bindings/jtag/
+F: Documentation/ABI/testing/jtag-cdev
+
K10TEMP HARDWARE MONITORING DRIVER
M: Clemens Ladisch <[email protected]>
L: [email protected]
diff --git a/drivers/Kconfig b/drivers/Kconfig
index 505c676..2214678 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -208,4 +208,6 @@ source "drivers/tee/Kconfig"
source "drivers/mux/Kconfig"
+source "drivers/jtag/Kconfig"
+
endmenu
diff --git a/drivers/Makefile b/drivers/Makefile
index dfdcda0..6a2059b 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -182,3 +182,4 @@ obj-$(CONFIG_FPGA) += fpga/
obj-$(CONFIG_FSI) += fsi/
obj-$(CONFIG_TEE) += tee/
obj-$(CONFIG_MULTIPLEXER) += mux/
+obj-$(CONFIG_JTAG) += jtag/
diff --git a/drivers/jtag/Kconfig b/drivers/jtag/Kconfig
new file mode 100644
index 0000000..0fad1a3
--- /dev/null
+++ b/drivers/jtag/Kconfig
@@ -0,0 +1,16 @@
+menuconfig JTAG
+ tristate "JTAG support"
+ ---help---
+ This provides basic core functionality support for jtag class devices
+ Hardware equipped with JTAG microcontroller which can be built
+ on top of this drivers. Driver exposes the set of IOCTL to the
+ user space for:
+ SIR (Scan Instruction Register, IEEE 1149.1 Data Register scan);
+ SDR (Scan Data Register, IEEE 1149.1 Instruction Register scan);
+ RUNTEST (Forces IEEE 1149.1 bus to a run state for specified
+ number of clocks).
+
+ If you want this support, you should say Y here.
+
+ To compile this driver as a module, choose M here: the module will
+ be called jtag.
diff --git a/drivers/jtag/Makefile b/drivers/jtag/Makefile
new file mode 100644
index 0000000..af37493
--- /dev/null
+++ b/drivers/jtag/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_JTAG) += jtag.o
diff --git a/drivers/jtag/jtag.c b/drivers/jtag/jtag.c
new file mode 100644
index 0000000..fbeba84
--- /dev/null
+++ b/drivers/jtag/jtag.c
@@ -0,0 +1,292 @@
+/*
+ * drivers/jtag/jtag.c
+ *
+ * Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2017 Oleksandr Shamray <[email protected]>
+ *
+ * Released under the GPLv2 only.
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <linux/cdev.h>
+#include <linux/device.h>
+#include <linux/jtag.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/miscdevice.h>
+#include <linux/module.h>
+#include <linux/rtnetlink.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <uapi/linux/jtag.h>
+
+#define JTAG_NAME "jtag0"
+#define MAX_JTAG_NAME_LEN (sizeof("jtag") + 5)
+
+struct jtag {
+ struct miscdevice miscdev;
+ struct device *dev;
+ const struct jtag_ops *ops;
+ int id;
+ bool opened;
+ struct mutex open_lock;
+ unsigned long priv[0];
+};
+
+static DEFINE_IDA(jtag_ida);
+
+void *jtag_priv(struct jtag *jtag)
+{
+ return jtag->priv;
+}
+EXPORT_SYMBOL_GPL(jtag_priv);
+
+static long jtag_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+ struct jtag *jtag = file->private_data;
+ struct jtag_run_test_idle idle;
+ struct jtag_xfer xfer;
+ u8 *xfer_data;
+ u32 data_size;
+ u32 value;
+ int err;
+
+ if (!arg)
+ return -EINVAL;
+
+ switch (cmd) {
+ case JTAG_GIOCFREQ:
+
+ if (jtag->ops->freq_get)
+ err = jtag->ops->freq_get(jtag, &value);
+ else
+ err = -EOPNOTSUPP;
+ if (err)
+ break;
+
+ if (put_user(value, (__u32 *)arg))
+ err = -EFAULT;
+ break;
+
+ case JTAG_SIOCFREQ:
+ if (get_user(value, (__u32 *)arg))
+ return -EFAULT;
+ if (value == 0)
+ return -EINVAL;
+
+ if (jtag->ops->freq_set)
+ err = jtag->ops->freq_set(jtag, value);
+ else
+ err = -EOPNOTSUPP;
+ break;
+
+ case JTAG_IOCRUNTEST:
+ if (copy_from_user(&idle, (void *)arg,
+ sizeof(struct jtag_run_test_idle)))
+ return -EFAULT;
+
+ if (idle.endstate > JTAG_STATE_PAUSEDR)
+ return -EINVAL;
+
+ if (jtag->ops->idle)
+ err = jtag->ops->idle(jtag, &idle);
+ else
+ err = -EOPNOTSUPP;
+ break;
+
+ case JTAG_IOCXFER:
+ if (copy_from_user(&xfer, (void *)arg,
+ sizeof(struct jtag_xfer)))
+ return -EFAULT;
+
+ if (xfer.length >= JTAG_MAX_XFER_DATA_LEN)
+ return -EINVAL;
+
+ if (xfer.type > JTAG_SDR_XFER)
+ return -EINVAL;
+
+ if (xfer.direction > JTAG_WRITE_XFER)
+ return -EINVAL;
+
+ if (xfer.endstate > JTAG_STATE_PAUSEDR)
+ return -EINVAL;
+
+ data_size = DIV_ROUND_UP(xfer.length, BITS_PER_BYTE);
+ xfer_data = memdup_user(u64_to_user_ptr(xfer.tdio), data_size);
+
+ if (!xfer_data)
+ return -EFAULT;
+
+ if (jtag->ops->xfer) {
+ err = jtag->ops->xfer(jtag, &xfer, xfer_data);
+ } else {
+ kfree(xfer_data);
+ return -EOPNOTSUPP;
+ }
+
+ if (err) {
+ kfree(xfer_data);
+ return -EFAULT;
+ }
+
+ err = copy_to_user(u64_to_user_ptr(xfer.tdio),
+ (void *)(xfer_data), data_size);
+
+ if (err) {
+ kfree(xfer_data);
+ return -EFAULT;
+ }
+
+ kfree(xfer_data);
+ if (copy_to_user((void *)arg, &xfer, sizeof(struct jtag_xfer)))
+ return -EFAULT;
+ break;
+
+ case JTAG_GIOCSTATUS:
+ if (jtag->ops->status_get)
+ err = jtag->ops->status_get(jtag, &value);
+ else
+ err = -EOPNOTSUPP;
+ if (err)
+ break;
+
+ err = put_user(value, (__u32 *)arg);
+ if (err)
+ err = -EFAULT;
+ break;
+ case JTAG_SIOCMODE:
+ if (get_user(value, (__u32 *)arg))
+ return -EFAULT;
+ if (value == 0)
+ return -EINVAL;
+
+ if (jtag->ops->mode_set)
+ err = jtag->ops->mode_set(jtag, value);
+ else
+ err = -EOPNOTSUPP;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ return err;
+}
+
+static int jtag_open(struct inode *inode, struct file *file)
+{
+ struct jtag *jtag = container_of(file->private_data, struct jtag,
+ miscdev);
+
+ if (mutex_lock_interruptible(&jtag->open_lock))
+ return -ERESTARTSYS;
+
+ if (jtag->opened) {
+ mutex_unlock(&jtag->open_lock);
+ return -EINVAL;
+ }
+
+ nonseekable_open(inode, file);
+ file->private_data = jtag;
+ jtag->opened = true;
+ mutex_unlock(&jtag->open_lock);
+ return 0;
+}
+
+static int jtag_release(struct inode *inode, struct file *file)
+{
+ struct jtag *jtag = file->private_data;
+
+ mutex_lock(&jtag->open_lock);
+ jtag->opened = false;
+ mutex_unlock(&jtag->open_lock);
+ return 0;
+}
+
+static const struct file_operations jtag_fops = {
+ .owner = THIS_MODULE,
+ .open = jtag_open,
+ .release = jtag_release,
+ .llseek = noop_llseek,
+ .unlocked_ioctl = jtag_ioctl,
+};
+
+struct jtag *jtag_alloc(size_t priv_size, const struct jtag_ops *ops)
+{
+ struct jtag *jtag;
+
+ jtag = kzalloc(sizeof(*jtag) + round_up(priv_size, ARCH_DMA_MINALIGN),
+ GFP_KERNEL);
+ if (!jtag)
+ return NULL;
+
+ jtag->ops = ops;
+ return jtag;
+}
+EXPORT_SYMBOL_GPL(jtag_alloc);
+
+void jtag_free(struct jtag *jtag)
+{
+ kfree(jtag);
+}
+EXPORT_SYMBOL_GPL(jtag_free);
+
+int jtag_register(struct jtag *jtag)
+{
+ char *name;
+ int err;
+ int id;
+
+ id = ida_simple_get(&jtag_ida, 0, 0, GFP_KERNEL);
+ if (id < 0)
+ return id;
+
+ jtag->id = id;
+
+ name = kzalloc(MAX_JTAG_NAME_LEN, GFP_KERNEL);
+ if (!name) {
+ err = -ENOMEM;
+ goto err_jtag_alloc;
+ }
+
+ err = snprintf(name, MAX_JTAG_NAME_LEN, "jtag%d", id);
+ if (err < 0)
+ goto err_jtag_name;
+
+ mutex_init(&jtag->open_lock);
+ jtag->miscdev.fops = &jtag_fops;
+ jtag->miscdev.minor = MISC_DYNAMIC_MINOR;
+ jtag->miscdev.name = name;
+
+ err = misc_register(&jtag->miscdev);
+ if (err)
+ dev_err(jtag->dev, "Unable to register device\n");
+ else
+ return 0;
+ jtag->opened = false;
+
+err_jtag_name:
+ kfree(name);
+err_jtag_alloc:
+ ida_simple_remove(&jtag_ida, id);
+ return err;
+}
+EXPORT_SYMBOL_GPL(jtag_register);
+
+void jtag_unregister(struct jtag *jtag)
+{
+ misc_deregister(&jtag->miscdev);
+ kfree(jtag->miscdev.name);
+ ida_simple_remove(&jtag_ida, jtag->id);
+}
+EXPORT_SYMBOL_GPL(jtag_unregister);
+
+static void __exit jtag_exit(void)
+{
+ ida_destroy(&jtag_ida);
+}
+
+module_exit(jtag_exit);
+
+MODULE_AUTHOR("Oleksandr Shamray <[email protected]>");
+MODULE_DESCRIPTION("Generic jtag support");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/jtag.h b/include/linux/jtag.h
new file mode 100644
index 0000000..66b6389
--- /dev/null
+++ b/include/linux/jtag.h
@@ -0,0 +1,46 @@
+/* SPDX-License-Identifier: GPL-2.0
+ * include/linux/jtag.h - JTAG class driver
+ *
+ * Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2017 Oleksandr Shamray <[email protected]>
+ */
+
+#ifndef __JTAG_H
+#define __JTAG_H
+
+#include <uapi/linux/jtag.h>
+
+#ifndef ARCH_DMA_MINALIGN
+#define ARCH_DMA_MINALIGN 1
+#endif
+
+#define jtag_u64_to_ptr(arg) ((void *)(uintptr_t)arg)
+
+#define JTAG_MAX_XFER_DATA_LEN 65535
+
+struct jtag;
+/**
+ * struct jtag_ops - callbacks for jtag control functions:
+ *
+ * @freq_get: get frequency function. Filled by device driver
+ * @freq_set: set frequency function. Filled by device driver
+ * @status_get: set status function. Filled by device driver
+ * @idle: set JTAG to idle state function. Filled by device driver
+ * @xfer: send JTAG xfer function. Filled by device driver
+ */
+struct jtag_ops {
+ int (*freq_get)(struct jtag *jtag, u32 *freq);
+ int (*freq_set)(struct jtag *jtag, u32 freq);
+ int (*status_get)(struct jtag *jtag, u32 *state);
+ int (*idle)(struct jtag *jtag, struct jtag_run_test_idle *idle);
+ int (*xfer)(struct jtag *jtag, struct jtag_xfer *xfer, u8 *xfer_data);
+ int (*mode_set)(struct jtag *jtag, u32 mode_mask);
+};
+
+void *jtag_priv(struct jtag *jtag);
+int jtag_register(struct jtag *jtag);
+void jtag_unregister(struct jtag *jtag);
+struct jtag *jtag_alloc(size_t priv_size, const struct jtag_ops *ops);
+void jtag_free(struct jtag *jtag);
+
+#endif /* __JTAG_H */
diff --git a/include/uapi/linux/jtag.h b/include/uapi/linux/jtag.h
new file mode 100644
index 0000000..b6c4dde
--- /dev/null
+++ b/include/uapi/linux/jtag.h
@@ -0,0 +1,105 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note
+ * include/uapi/linux/jtag.h - JTAG class driver uapi
+ *
+ * Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2017 Oleksandr Shamray <[email protected]>
+ */
+
+#ifndef __UAPI_LINUX_JTAG_H
+#define __UAPI_LINUX_JTAG_H
+
+#include <linux/types.h>
+/*
+ * JTAG_XFER_HW_MODE: JTAG hardware mode. Used to set HW drived or bitbang
+ * mode. This is bitmask param of ioctl JTAG_SIOCMODE command
+ */
+#define JTAG_XFER_HW_MODE 1
+
+/**
+ * enum jtag_endstate:
+ *
+ * @JTAG_STATE_IDLE: JTAG state machine IDLE state
+ * @JTAG_STATE_PAUSEIR: JTAG state machine PAUSE_IR state
+ * @JTAG_STATE_PAUSEDR: JTAG state machine PAUSE_DR state
+ */
+enum jtag_endstate {
+ JTAG_STATE_IDLE,
+ JTAG_STATE_PAUSEIR,
+ JTAG_STATE_PAUSEDR,
+};
+
+/**
+ * enum jtag_xfer_type:
+ *
+ * @JTAG_SIR_XFER: SIR transfer
+ * @JTAG_SDR_XFER: SDR transfer
+ */
+enum jtag_xfer_type {
+ JTAG_SIR_XFER,
+ JTAG_SDR_XFER,
+};
+
+/**
+ * enum jtag_xfer_direction:
+ *
+ * @JTAG_READ_XFER: read transfer
+ * @JTAG_WRITE_XFER: write transfer
+ */
+enum jtag_xfer_direction {
+ JTAG_READ_XFER,
+ JTAG_WRITE_XFER,
+};
+
+/**
+ * struct jtag_run_test_idle - forces JTAG state machine to
+ * RUN_TEST/IDLE state
+ *
+ * @reset: 0 - run IDLE/PAUSE from current state
+ * 1 - go through TEST_LOGIC/RESET state before IDLE/PAUSE
+ * @end: completion flag
+ * @tck: clock counter
+ *
+ * Structure represents interface to JTAG device for jtag idle
+ * execution.
+ */
+struct jtag_run_test_idle {
+ __u8 reset;
+ __u8 endstate;
+ __u8 tck;
+};
+
+/**
+ * struct jtag_xfer - jtag xfer:
+ *
+ * @type: transfer type
+ * @direction: xfer direction
+ * @length: xfer bits len
+ * @tdio : xfer data array
+ * @endir: xfer end state
+ *
+ * Structure represents interface to JTAG device for jtag sdr xfer
+ * execution.
+ */
+struct jtag_xfer {
+ __u8 type;
+ __u8 direction;
+ __u8 endstate;
+ __u32 length;
+ __u64 tdio;
+};
+
+/* ioctl interface */
+#define __JTAG_IOCTL_MAGIC 0xb2
+
+#define JTAG_IOCRUNTEST _IOW(__JTAG_IOCTL_MAGIC, 0,\
+ struct jtag_run_test_idle)
+#define JTAG_SIOCFREQ _IOW(__JTAG_IOCTL_MAGIC, 1, unsigned int)
+#define JTAG_GIOCFREQ _IOR(__JTAG_IOCTL_MAGIC, 2, unsigned int)
+#define JTAG_IOCXFER _IOWR(__JTAG_IOCTL_MAGIC, 3, struct jtag_xfer)
+#define JTAG_GIOCSTATUS _IOWR(__JTAG_IOCTL_MAGIC, 4, enum jtag_endstate)
+#define JTAG_SIOCMODE _IOW(__JTAG_IOCTL_MAGIC, 5, unsigned int)
+
+#define JTAG_FIRST_MINOR 0
+#define JTAG_MAX_DEVICES 32
+
+#endif /* __UAPI_LINUX_JTAG_H */
--
1.7.1
From 1582940698393177770@xxx Thu Nov 02 08:04:48 +0000 2017
X-GM-THRID: 1582020059610310290
X-Gmail-Labels: Inbox,Category Forums,HistoricalUnread