In some cases the hardware that the bootloader has left configured
depends on RPMH power domains for their operation up until the point
where the related Linux device driver probes and can inherit that
configuration, or power down the hardware gracefully.
Unfortunately as Linux probes the releavant drivers in sequence there
are periods during the Linux boot flow where either the genpd refcount
will reach 0, or worse where the active performance_state votes does not
meet the requirements of the state that the hardware was left in.
One specific example of this is during boot of e.g. SM8150/SC8180X,
where the display clock controller probes, without any particular
performance state needs (to access its registers). This will drop the
MMCX rail to MIN_SVS, which isn't sufficient to sustain the clock rates
that the later probing MDP is configured to. This results in an
unrecoverable system state.
Handle both these cases by keeping the RPMH power-domais that are
referenced voted for highest state, until sync_state indicates that all
devices referencing the RPMH power-domain driver has been probed.
Signed-off-by: Bjorn Andersson <[email protected]>
---
drivers/soc/qcom/rpmhpd.c | 35 ++++++++++++++++++++++++++++++++++-
1 file changed, 34 insertions(+), 1 deletion(-)
diff --git a/drivers/soc/qcom/rpmhpd.c b/drivers/soc/qcom/rpmhpd.c
index 092f6ab09acf..494bb6c75ed7 100644
--- a/drivers/soc/qcom/rpmhpd.c
+++ b/drivers/soc/qcom/rpmhpd.c
@@ -39,6 +39,7 @@
* @res_name: Resource name used for cmd-db lookup
* @addr: Resource address as looped up using resource name from
* cmd-db
+ * @state_synced: Indicator that sync_state has been invoked for the rpmhpd resource
*/
struct rpmhpd {
struct device *dev;
@@ -54,6 +55,7 @@ struct rpmhpd {
bool enabled;
const char *res_name;
u32 addr;
+ bool state_synced;
};
struct rpmhpd_desc {
@@ -493,7 +495,13 @@ static int rpmhpd_aggregate_corner(struct rpmhpd *pd, unsigned int corner)
unsigned int this_active_corner = 0, this_sleep_corner = 0;
unsigned int peer_active_corner = 0, peer_sleep_corner = 0;
- to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
+ if (pd->state_synced) {
+ to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
+ } else {
+ /* Clamp to highest corner if sync_state hasn't happened */
+ this_active_corner = pd->level_count - 1;
+ this_sleep_corner = pd->level_count - 1;
+ }
if (peer && peer->enabled)
to_active_sleep(peer, peer->corner, &peer_active_corner,
@@ -708,11 +716,36 @@ static int rpmhpd_probe(struct platform_device *pdev)
return of_genpd_add_provider_onecell(pdev->dev.of_node, data);
}
+static void rpmhpd_sync_state(struct device *dev)
+{
+ const struct rpmhpd_desc *desc = of_device_get_match_data(dev);
+ struct rpmhpd **rpmhpds = desc->rpmhpds;
+ unsigned int corner;
+ struct rpmhpd *pd;
+ unsigned int i;
+
+ mutex_lock(&rpmhpd_lock);
+ for (i = 0; i < desc->num_pds; i++) {
+ pd = rpmhpds[i];
+ if (!pd)
+ continue;
+
+ pd->state_synced = true;
+ if (pd->enabled)
+ corner = max(pd->corner, pd->enable_corner);
+ else
+ corner = 0;
+ rpmhpd_aggregate_corner(pd, corner);
+ }
+ mutex_unlock(&rpmhpd_lock);
+}
+
static struct platform_driver rpmhpd_driver = {
.driver = {
.name = "qcom-rpmhpd",
.of_match_table = rpmhpd_match_table,
.suppress_bind_attrs = true,
+ .sync_state = rpmhpd_sync_state,
},
.probe = rpmhpd_probe,
};
--
2.35.1
On 06/08/2022 18:50, Bjorn Andersson wrote:
> In some cases the hardware that the bootloader has left configured
> depends on RPMH power domains for their operation up until the point
> where the related Linux device driver probes and can inherit that
> configuration, or power down the hardware gracefully.
>
> Unfortunately as Linux probes the releavant drivers in sequence there
> are periods during the Linux boot flow where either the genpd refcount
> will reach 0, or worse where the active performance_state votes does not
> meet the requirements of the state that the hardware was left in.
>
> One specific example of this is during boot of e.g. SM8150/SC8180X,
> where the display clock controller probes, without any particular
> performance state needs (to access its registers). This will drop the
> MMCX rail to MIN_SVS, which isn't sufficient to sustain the clock rates
> that the later probing MDP is configured to. This results in an
> unrecoverable system state.
>
> Handle both these cases by keeping the RPMH power-domais that are
> referenced voted for highest state, until sync_state indicates that all
> devices referencing the RPMH power-domain driver has been probed.
>
> Signed-off-by: Bjorn Andersson <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
> ---
> drivers/soc/qcom/rpmhpd.c | 35 ++++++++++++++++++++++++++++++++++-
> 1 file changed, 34 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/soc/qcom/rpmhpd.c b/drivers/soc/qcom/rpmhpd.c
> index 092f6ab09acf..494bb6c75ed7 100644
> --- a/drivers/soc/qcom/rpmhpd.c
> +++ b/drivers/soc/qcom/rpmhpd.c
> @@ -39,6 +39,7 @@
> * @res_name: Resource name used for cmd-db lookup
> * @addr: Resource address as looped up using resource name from
> * cmd-db
> + * @state_synced: Indicator that sync_state has been invoked for the rpmhpd resource
> */
> struct rpmhpd {
> struct device *dev;
> @@ -54,6 +55,7 @@ struct rpmhpd {
> bool enabled;
> const char *res_name;
> u32 addr;
> + bool state_synced;
> };
>
> struct rpmhpd_desc {
> @@ -493,7 +495,13 @@ static int rpmhpd_aggregate_corner(struct rpmhpd *pd, unsigned int corner)
> unsigned int this_active_corner = 0, this_sleep_corner = 0;
> unsigned int peer_active_corner = 0, peer_sleep_corner = 0;
>
> - to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> + if (pd->state_synced) {
> + to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> + } else {
> + /* Clamp to highest corner if sync_state hasn't happened */
> + this_active_corner = pd->level_count - 1;
> + this_sleep_corner = pd->level_count - 1;
> + }
>
> if (peer && peer->enabled)
> to_active_sleep(peer, peer->corner, &peer_active_corner,
> @@ -708,11 +716,36 @@ static int rpmhpd_probe(struct platform_device *pdev)
> return of_genpd_add_provider_onecell(pdev->dev.of_node, data);
> }
>
> +static void rpmhpd_sync_state(struct device *dev)
> +{
> + const struct rpmhpd_desc *desc = of_device_get_match_data(dev);
> + struct rpmhpd **rpmhpds = desc->rpmhpds;
> + unsigned int corner;
> + struct rpmhpd *pd;
> + unsigned int i;
> +
> + mutex_lock(&rpmhpd_lock);
> + for (i = 0; i < desc->num_pds; i++) {
> + pd = rpmhpds[i];
> + if (!pd)
> + continue;
> +
> + pd->state_synced = true;
> + if (pd->enabled)
> + corner = max(pd->corner, pd->enable_corner);
> + else
> + corner = 0;
> + rpmhpd_aggregate_corner(pd, corner);
> + }
> + mutex_unlock(&rpmhpd_lock);
> +}
> +
> static struct platform_driver rpmhpd_driver = {
> .driver = {
> .name = "qcom-rpmhpd",
> .of_match_table = rpmhpd_match_table,
> .suppress_bind_attrs = true,
> + .sync_state = rpmhpd_sync_state,
> },
> .probe = rpmhpd_probe,
> };
--
With best wishes
Dmitry
On 6.08.2022 17:50, Bjorn Andersson wrote:
> In some cases the hardware that the bootloader has left configured
> depends on RPMH power domains for their operation up until the point
> where the related Linux device driver probes and can inherit that
> configuration, or power down the hardware gracefully.
>
> Unfortunately as Linux probes the releavant drivers in sequence there
> are periods during the Linux boot flow where either the genpd refcount
> will reach 0, or worse where the active performance_state votes does not
> meet the requirements of the state that the hardware was left in.
>
> One specific example of this is during boot of e.g. SM8150/SC8180X,
> where the display clock controller probes, without any particular
> performance state needs (to access its registers). This will drop the
> MMCX rail to MIN_SVS, which isn't sufficient to sustain the clock rates
> that the later probing MDP is configured to. This results in an
> unrecoverable system state.
>
> Handle both these cases by keeping the RPMH power-domais that are
> referenced voted for highest state, until sync_state indicates that all
> devices referencing the RPMH power-domain driver has been probed.
>
> Signed-off-by: Bjorn Andersson <[email protected]>
> ---
Must have been fun to debug..
Reviewed-by: Konrad Dybcio <[email protected]>
Konrad
> drivers/soc/qcom/rpmhpd.c | 35 ++++++++++++++++++++++++++++++++++-
> 1 file changed, 34 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/soc/qcom/rpmhpd.c b/drivers/soc/qcom/rpmhpd.c
> index 092f6ab09acf..494bb6c75ed7 100644
> --- a/drivers/soc/qcom/rpmhpd.c
> +++ b/drivers/soc/qcom/rpmhpd.c
> @@ -39,6 +39,7 @@
> * @res_name: Resource name used for cmd-db lookup
> * @addr: Resource address as looped up using resource name from
> * cmd-db
> + * @state_synced: Indicator that sync_state has been invoked for the rpmhpd resource
> */
> struct rpmhpd {
> struct device *dev;
> @@ -54,6 +55,7 @@ struct rpmhpd {
> bool enabled;
> const char *res_name;
> u32 addr;
> + bool state_synced;
> };
>
> struct rpmhpd_desc {
> @@ -493,7 +495,13 @@ static int rpmhpd_aggregate_corner(struct rpmhpd *pd, unsigned int corner)
> unsigned int this_active_corner = 0, this_sleep_corner = 0;
> unsigned int peer_active_corner = 0, peer_sleep_corner = 0;
>
> - to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> + if (pd->state_synced) {
> + to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> + } else {
> + /* Clamp to highest corner if sync_state hasn't happened */
> + this_active_corner = pd->level_count - 1;
> + this_sleep_corner = pd->level_count - 1;
> + }
>
> if (peer && peer->enabled)
> to_active_sleep(peer, peer->corner, &peer_active_corner,
> @@ -708,11 +716,36 @@ static int rpmhpd_probe(struct platform_device *pdev)
> return of_genpd_add_provider_onecell(pdev->dev.of_node, data);
> }
>
> +static void rpmhpd_sync_state(struct device *dev)
> +{
> + const struct rpmhpd_desc *desc = of_device_get_match_data(dev);
> + struct rpmhpd **rpmhpds = desc->rpmhpds;
> + unsigned int corner;
> + struct rpmhpd *pd;
> + unsigned int i;
> +
> + mutex_lock(&rpmhpd_lock);
> + for (i = 0; i < desc->num_pds; i++) {
> + pd = rpmhpds[i];
> + if (!pd)
> + continue;
> +
> + pd->state_synced = true;
> + if (pd->enabled)
> + corner = max(pd->corner, pd->enable_corner);
> + else
> + corner = 0;
> + rpmhpd_aggregate_corner(pd, corner);
> + }
> + mutex_unlock(&rpmhpd_lock);
> +}
> +
> static struct platform_driver rpmhpd_driver = {
> .driver = {
> .name = "qcom-rpmhpd",
> .of_match_table = rpmhpd_match_table,
> .suppress_bind_attrs = true,
> + .sync_state = rpmhpd_sync_state,
> },
> .probe = rpmhpd_probe,
> };
On 06/08/2022 16:50, Bjorn Andersson wrote:
> In some cases the hardware that the bootloader has left configured
> depends on RPMH power domains for their operation up until the point
> where the related Linux device driver probes and can inherit that
> configuration, or power down the hardware gracefully.
>
> Unfortunately as Linux probes the releavant drivers in sequence there
> are periods during the Linux boot flow where either the genpd refcount
> will reach 0, or worse where the active performance_state votes does not
> meet the requirements of the state that the hardware was left in.
>
> One specific example of this is during boot of e.g. SM8150/SC8180X,
> where the display clock controller probes, without any particular
> performance state needs (to access its registers). This will drop the
> MMCX rail to MIN_SVS, which isn't sufficient to sustain the clock rates
> that the later probing MDP is configured to. This results in an
> unrecoverable system state.
Hi Bjorn,
Seems like my sm8150 device dies before getting this far, bah!
>
> Handle both these cases by keeping the RPMH power-domais that are
> referenced voted for highest state, until sync_state indicates that all
> devices referencing the RPMH power-domain driver has been probed.
>
> Signed-off-by: Bjorn Andersson <[email protected]>
Reviewed-by: Caleb Connolly <[email protected]>
> ---
> drivers/soc/qcom/rpmhpd.c | 35 ++++++++++++++++++++++++++++++++++-
> 1 file changed, 34 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/soc/qcom/rpmhpd.c b/drivers/soc/qcom/rpmhpd.c
> index 092f6ab09acf..494bb6c75ed7 100644
> --- a/drivers/soc/qcom/rpmhpd.c
> +++ b/drivers/soc/qcom/rpmhpd.c
> @@ -39,6 +39,7 @@
> * @res_name: Resource name used for cmd-db lookup
> * @addr: Resource address as looped up using resource name from
> * cmd-db
> + * @state_synced: Indicator that sync_state has been invoked for the rpmhpd resource
> */
> struct rpmhpd {
> struct device *dev;
> @@ -54,6 +55,7 @@ struct rpmhpd {
> bool enabled;
> const char *res_name;
> u32 addr;
> + bool state_synced;
> };
>
> struct rpmhpd_desc {
> @@ -493,7 +495,13 @@ static int rpmhpd_aggregate_corner(struct rpmhpd *pd, unsigned int corner)
> unsigned int this_active_corner = 0, this_sleep_corner = 0;
> unsigned int peer_active_corner = 0, peer_sleep_corner = 0;
>
> - to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> + if (pd->state_synced) {
> + to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> + } else {
> + /* Clamp to highest corner if sync_state hasn't happened */
> + this_active_corner = pd->level_count - 1;
> + this_sleep_corner = pd->level_count - 1;
> + }
>
> if (peer && peer->enabled)
> to_active_sleep(peer, peer->corner, &peer_active_corner,
> @@ -708,11 +716,36 @@ static int rpmhpd_probe(struct platform_device *pdev)
> return of_genpd_add_provider_onecell(pdev->dev.of_node, data);
> }
>
> +static void rpmhpd_sync_state(struct device *dev)
> +{
> + const struct rpmhpd_desc *desc = of_device_get_match_data(dev);
> + struct rpmhpd **rpmhpds = desc->rpmhpds;
> + unsigned int corner;
> + struct rpmhpd *pd;
> + unsigned int i;
> +
> + mutex_lock(&rpmhpd_lock);
> + for (i = 0; i < desc->num_pds; i++) {
> + pd = rpmhpds[i];
> + if (!pd)
> + continue;
> +
> + pd->state_synced = true;
> + if (pd->enabled)
> + corner = max(pd->corner, pd->enable_corner);
> + else
> + corner = 0;
> + rpmhpd_aggregate_corner(pd, corner);
> + }
> + mutex_unlock(&rpmhpd_lock);
> +}
> +
> static struct platform_driver rpmhpd_driver = {
> .driver = {
> .name = "qcom-rpmhpd",
> .of_match_table = rpmhpd_match_table,
> .suppress_bind_attrs = true,
> + .sync_state = rpmhpd_sync_state,
> },
> .probe = rpmhpd_probe,
> };
> --
> 2.35.1
>
--
Kind Regards,
Caleb
On 8/6/2022 9:20 PM, Bjorn Andersson wrote:
> In some cases the hardware that the bootloader has left configured
> depends on RPMH power domains for their operation up until the point
> where the related Linux device driver probes and can inherit that
> configuration, or power down the hardware gracefully.
>
> Unfortunately as Linux probes the releavant drivers in sequence there
> are periods during the Linux boot flow where either the genpd refcount
> will reach 0, or worse where the active performance_state votes does not
> meet the requirements of the state that the hardware was left in.
>
> One specific example of this is during boot of e.g. SM8150/SC8180X,
> where the display clock controller probes, without any particular
> performance state needs (to access its registers). This will drop the
> MMCX rail to MIN_SVS, which isn't sufficient to sustain the clock rates
> that the later probing MDP is configured to. This results in an
> unrecoverable system state.
>
> Handle both these cases by keeping the RPMH power-domais that are
> referenced voted for highest state, until sync_state indicates that all
> devices referencing the RPMH power-domain driver has been probed.
>
> Signed-off-by: Bjorn Andersson <[email protected]>
> ---
> drivers/soc/qcom/rpmhpd.c | 35 ++++++++++++++++++++++++++++++++++-
> 1 file changed, 34 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/soc/qcom/rpmhpd.c b/drivers/soc/qcom/rpmhpd.c
> index 092f6ab09acf..494bb6c75ed7 100644
> --- a/drivers/soc/qcom/rpmhpd.c
> +++ b/drivers/soc/qcom/rpmhpd.c
> @@ -39,6 +39,7 @@
> * @res_name: Resource name used for cmd-db lookup
> * @addr: Resource address as looped up using resource name from
> * cmd-db
> + * @state_synced: Indicator that sync_state has been invoked for the rpmhpd resource
> */
> struct rpmhpd {
> struct device *dev;
> @@ -54,6 +55,7 @@ struct rpmhpd {
> bool enabled;
> const char *res_name;
> u32 addr;
> + bool state_synced;
> };
>
> struct rpmhpd_desc {
> @@ -493,7 +495,13 @@ static int rpmhpd_aggregate_corner(struct rpmhpd *pd, unsigned int corner)
> unsigned int this_active_corner = 0, this_sleep_corner = 0;
> unsigned int peer_active_corner = 0, peer_sleep_corner = 0;
>
> - to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> + if (pd->state_synced) {
> + to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> + } else {
> + /* Clamp to highest corner if sync_state hasn't happened */
> + this_active_corner = pd->level_count - 1;
> + this_sleep_corner = pd->level_count - 1;
> + }
>
> if (peer && peer->enabled)
> to_active_sleep(peer, peer->corner, &peer_active_corner,
> @@ -708,11 +716,36 @@ static int rpmhpd_probe(struct platform_device *pdev)
> return of_genpd_add_provider_onecell(pdev->dev.of_node, data);
> }
>
> +static void rpmhpd_sync_state(struct device *dev)
> +{
> + const struct rpmhpd_desc *desc = of_device_get_match_data(dev);
> + struct rpmhpd **rpmhpds = desc->rpmhpds;
> + unsigned int corner;
> + struct rpmhpd *pd;
> + unsigned int i;
> +
> + mutex_lock(&rpmhpd_lock);
> + for (i = 0; i < desc->num_pds; i++) {
> + pd = rpmhpds[i];
> + if (!pd)
> + continue;
> +
> + pd->state_synced = true;
[]
> + if (pd->enabled)
> + corner = max(pd->corner, pd->enable_corner);
> + else
> + corner = 0;
> + rpmhpd_aggregate_corner(pd, corner);
can't this be
if (pd->enabled) {
corner = max(pd->corner, pd->enable_corner);
rpmhpd_aggregate_corner(pd, corner);
}
also, we do check for return value of rpmhpd_aggregate_corner() but I guess
here there isn't much different we would do even if there is an error?
> + }
> + mutex_unlock(&rpmhpd_lock);
> +}
> +
> static struct platform_driver rpmhpd_driver = {
> .driver = {
> .name = "qcom-rpmhpd",
> .of_match_table = rpmhpd_match_table,
> .suppress_bind_attrs = true,
> + .sync_state = rpmhpd_sync_state,
> },
> .probe = rpmhpd_probe,
> };
On Mon 08 Aug 03:17 CDT 2022, Rajendra Nayak wrote:
>
> On 8/6/2022 9:20 PM, Bjorn Andersson wrote:
> > In some cases the hardware that the bootloader has left configured
> > depends on RPMH power domains for their operation up until the point
> > where the related Linux device driver probes and can inherit that
> > configuration, or power down the hardware gracefully.
> >
> > Unfortunately as Linux probes the releavant drivers in sequence there
> > are periods during the Linux boot flow where either the genpd refcount
> > will reach 0, or worse where the active performance_state votes does not
> > meet the requirements of the state that the hardware was left in.
> >
> > One specific example of this is during boot of e.g. SM8150/SC8180X,
> > where the display clock controller probes, without any particular
> > performance state needs (to access its registers). This will drop the
> > MMCX rail to MIN_SVS, which isn't sufficient to sustain the clock rates
> > that the later probing MDP is configured to. This results in an
> > unrecoverable system state.
> >
> > Handle both these cases by keeping the RPMH power-domais that are
> > referenced voted for highest state, until sync_state indicates that all
> > devices referencing the RPMH power-domain driver has been probed.
> >
> > Signed-off-by: Bjorn Andersson <[email protected]>
> > ---
> > drivers/soc/qcom/rpmhpd.c | 35 ++++++++++++++++++++++++++++++++++-
> > 1 file changed, 34 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/soc/qcom/rpmhpd.c b/drivers/soc/qcom/rpmhpd.c
> > index 092f6ab09acf..494bb6c75ed7 100644
> > --- a/drivers/soc/qcom/rpmhpd.c
> > +++ b/drivers/soc/qcom/rpmhpd.c
> > @@ -39,6 +39,7 @@
> > * @res_name: Resource name used for cmd-db lookup
> > * @addr: Resource address as looped up using resource name from
> > * cmd-db
> > + * @state_synced: Indicator that sync_state has been invoked for the rpmhpd resource
> > */
> > struct rpmhpd {
> > struct device *dev;
> > @@ -54,6 +55,7 @@ struct rpmhpd {
> > bool enabled;
> > const char *res_name;
> > u32 addr;
> > + bool state_synced;
> > };
> > struct rpmhpd_desc {
> > @@ -493,7 +495,13 @@ static int rpmhpd_aggregate_corner(struct rpmhpd *pd, unsigned int corner)
> > unsigned int this_active_corner = 0, this_sleep_corner = 0;
> > unsigned int peer_active_corner = 0, peer_sleep_corner = 0;
> > - to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> > + if (pd->state_synced) {
> > + to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
> > + } else {
> > + /* Clamp to highest corner if sync_state hasn't happened */
> > + this_active_corner = pd->level_count - 1;
> > + this_sleep_corner = pd->level_count - 1;
> > + }
> > if (peer && peer->enabled)
> > to_active_sleep(peer, peer->corner, &peer_active_corner,
> > @@ -708,11 +716,36 @@ static int rpmhpd_probe(struct platform_device *pdev)
> > return of_genpd_add_provider_onecell(pdev->dev.of_node, data);
> > }
> > +static void rpmhpd_sync_state(struct device *dev)
> > +{
> > + const struct rpmhpd_desc *desc = of_device_get_match_data(dev);
> > + struct rpmhpd **rpmhpds = desc->rpmhpds;
> > + unsigned int corner;
> > + struct rpmhpd *pd;
> > + unsigned int i;
> > +
> > + mutex_lock(&rpmhpd_lock);
> > + for (i = 0; i < desc->num_pds; i++) {
> > + pd = rpmhpds[i];
> > + if (!pd)
> > + continue;
> > +
> > + pd->state_synced = true;
> []
>
> > + if (pd->enabled)
> > + corner = max(pd->corner, pd->enable_corner);
> > + else
> > + corner = 0;
> > + rpmhpd_aggregate_corner(pd, corner);
>
> can't this be
> if (pd->enabled) {
> corner = max(pd->corner, pd->enable_corner);
> rpmhpd_aggregate_corner(pd, corner);
> }
Please correct me if I'm wrong, but that would imply that if the
power-domain was disabled by all clients when we hit the sync_state we
would be left at max state until one of them tickles it again.
The way it's written here means that in addition to keeping things at
the highest corner we also keep it on until sync_state hits - but no
longer.
>
> also, we do check for return value of rpmhpd_aggregate_corner() but I guess
> here there isn't much different we would do even if there is an error?
>
You're right, ignoring the return value here means that an error would
be completely silent. There's not much we can do about it, but it might
be useful to the developer to know that this happened.
So a dev_err() seems in order.
Thanks,
Bjorn
> > + }
> > + mutex_unlock(&rpmhpd_lock);
> > +}
> > +
> > static struct platform_driver rpmhpd_driver = {
> > .driver = {
> > .name = "qcom-rpmhpd",
> > .of_match_table = rpmhpd_match_table,
> > .suppress_bind_attrs = true,
> > + .sync_state = rpmhpd_sync_state,
> > },
> > .probe = rpmhpd_probe,
> > };
On 8/10/2022 2:25 AM, Bjorn Andersson wrote:
> On Mon 08 Aug 03:17 CDT 2022, Rajendra Nayak wrote:
>
>>
>> On 8/6/2022 9:20 PM, Bjorn Andersson wrote:
>>> In some cases the hardware that the bootloader has left configured
>>> depends on RPMH power domains for their operation up until the point
>>> where the related Linux device driver probes and can inherit that
>>> configuration, or power down the hardware gracefully.
>>>
>>> Unfortunately as Linux probes the releavant drivers in sequence there
>>> are periods during the Linux boot flow where either the genpd refcount
>>> will reach 0, or worse where the active performance_state votes does not
>>> meet the requirements of the state that the hardware was left in.
>>>
>>> One specific example of this is during boot of e.g. SM8150/SC8180X,
>>> where the display clock controller probes, without any particular
>>> performance state needs (to access its registers). This will drop the
>>> MMCX rail to MIN_SVS, which isn't sufficient to sustain the clock rates
>>> that the later probing MDP is configured to. This results in an
>>> unrecoverable system state.
>>>
>>> Handle both these cases by keeping the RPMH power-domais that are
>>> referenced voted for highest state, until sync_state indicates that all
>>> devices referencing the RPMH power-domain driver has been probed.
>>>
>>> Signed-off-by: Bjorn Andersson <[email protected]>
>>> ---
>>> drivers/soc/qcom/rpmhpd.c | 35 ++++++++++++++++++++++++++++++++++-
>>> 1 file changed, 34 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/drivers/soc/qcom/rpmhpd.c b/drivers/soc/qcom/rpmhpd.c
>>> index 092f6ab09acf..494bb6c75ed7 100644
>>> --- a/drivers/soc/qcom/rpmhpd.c
>>> +++ b/drivers/soc/qcom/rpmhpd.c
>>> @@ -39,6 +39,7 @@
>>> * @res_name: Resource name used for cmd-db lookup
>>> * @addr: Resource address as looped up using resource name from
>>> * cmd-db
>>> + * @state_synced: Indicator that sync_state has been invoked for the rpmhpd resource
>>> */
>>> struct rpmhpd {
>>> struct device *dev;
>>> @@ -54,6 +55,7 @@ struct rpmhpd {
>>> bool enabled;
>>> const char *res_name;
>>> u32 addr;
>>> + bool state_synced;
>>> };
>>> struct rpmhpd_desc {
>>> @@ -493,7 +495,13 @@ static int rpmhpd_aggregate_corner(struct rpmhpd *pd, unsigned int corner)
>>> unsigned int this_active_corner = 0, this_sleep_corner = 0;
>>> unsigned int peer_active_corner = 0, peer_sleep_corner = 0;
>>> - to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
>>> + if (pd->state_synced) {
>>> + to_active_sleep(pd, corner, &this_active_corner, &this_sleep_corner);
>>> + } else {
>>> + /* Clamp to highest corner if sync_state hasn't happened */
>>> + this_active_corner = pd->level_count - 1;
>>> + this_sleep_corner = pd->level_count - 1;
>>> + }
>>> if (peer && peer->enabled)
>>> to_active_sleep(peer, peer->corner, &peer_active_corner,
>>> @@ -708,11 +716,36 @@ static int rpmhpd_probe(struct platform_device *pdev)
>>> return of_genpd_add_provider_onecell(pdev->dev.of_node, data);
>>> }
>>> +static void rpmhpd_sync_state(struct device *dev)
>>> +{
>>> + const struct rpmhpd_desc *desc = of_device_get_match_data(dev);
>>> + struct rpmhpd **rpmhpds = desc->rpmhpds;
>>> + unsigned int corner;
>>> + struct rpmhpd *pd;
>>> + unsigned int i;
>>> +
>>> + mutex_lock(&rpmhpd_lock);
>>> + for (i = 0; i < desc->num_pds; i++) {
>>> + pd = rpmhpds[i];
>>> + if (!pd)
>>> + continue;
>>> +
>>> + pd->state_synced = true;
>> []
>>
>>> + if (pd->enabled)
>>> + corner = max(pd->corner, pd->enable_corner);
>>> + else
>>> + corner = 0;
>>> + rpmhpd_aggregate_corner(pd, corner);
>>
>> can't this be
>> if (pd->enabled) {
>> corner = max(pd->corner, pd->enable_corner);
>> rpmhpd_aggregate_corner(pd, corner);
>> }
>
> Please correct me if I'm wrong, but that would imply that if the
> power-domain was disabled by all clients when we hit the sync_state we
> would be left at max state until one of them tickles it again.
>
> The way it's written here means that in addition to keeping things at
> the highest corner we also keep it on until sync_state hits - but no
> longer.
ah, that's right, seems like the right thing to do.
>>
>> also, we do check for return value of rpmhpd_aggregate_corner() but I guess
>> here there isn't much different we would do even if there is an error?
>>
>
> You're right, ignoring the return value here means that an error would
> be completely silent. There's not much we can do about it, but it might
> be useful to the developer to know that this happened.
>
> So a dev_err() seems in order.
>
> Thanks,
> Bjorn
>
>>> + }
>>> + mutex_unlock(&rpmhpd_lock);
>>> +}
>>> +
>>> static struct platform_driver rpmhpd_driver = {
>>> .driver = {
>>> .name = "qcom-rpmhpd",
>>> .of_match_table = rpmhpd_match_table,
>>> .suppress_bind_attrs = true,
>>> + .sync_state = rpmhpd_sync_state,
>>> },
>>> .probe = rpmhpd_probe,
>>> };