[v14]
* Addressed comment from Sudeep about DT compatible
* Added MAINTAINERS entry
[v13]
* Addressed comment from Sudeep about DT compatible check on init
[v12]
* Addressed comments from Sudeep and Viresh about the single init
[v11]
* Addressed comment from Russel about device_node reference
* Addressed comment from Sudeep about the late_initcall
* Transformed init into probe to take care of deferals
[v10]
* Split the series into domains
* Addressed comments from Viresh and Sudeep about logical CPU numbering.
The qcom-cpufreq-kryo driver is aimed to support different SOC versions.
The driver reads eFuse information and chooses the required OPP subset
by passing the OPP supported-hw parameter.
The series depends on the series from Viresh:
https://patchwork.kernel.org/patch/10418139/
The previous spin was here:
https://patchwork.kernel.org/patch/10424949/
Ilia Lin (2):
cpufreq: Add Kryo CPU scaling driver
dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu
.../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++
MAINTAINERS | 7 +
drivers/cpufreq/Kconfig.arm | 10 +
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/cpufreq-dt-platdev.c | 3 +
drivers/cpufreq/qcom-cpufreq-kryo.c | 212 +++++++
6 files changed, 913 insertions(+)
create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
--
1.9.1
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.
This change adds documentation for the DT bindings.
The "operating-points-v2-kryo-cpu" DT extends the "operating-points-v2"
with following parameters:
- nvmem-cells (NVMEM area containig the speedbin information)
- opp-supported-hw: A single 32 bit bitmap value,
representing compatible HW:
0: MSM8996 V3, speedbin 0
1: MSM8996 V3, speedbin 1
2: MSM8996 V3, speedbin 2
3: unused
4: MSM8996 SG, speedbin 0
5: MSM8996 SG, speedbin 1
6: MSM8996 SG, speedbin 2
7-31: unused
Signed-off-by: Ilia Lin <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
---
.../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++
1 file changed, 680 insertions(+)
create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
new file mode 100644
index 0000000..c2127b9
--- /dev/null
+++ b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
@@ -0,0 +1,680 @@
+Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings
+===================================
+
+In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
+that have KRYO processors, the CPU ferequencies subset and voltage value
+of each OPP varies based on the silicon variant in use.
+Qualcomm Technologies, Inc. Process Voltage Scaling Tables
+defines the voltage and frequency value based on the msm-id in SMEM
+and speedbin blown in the efuse combination.
+The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
+to provide the OPP framework with required information (existing HW bitmap).
+This is used to determine the voltage and frequency value for each OPP of
+operating-points-v2 table when it is parsed by the OPP framework.
+
+Required properties:
+--------------------
+In 'cpus' nodes:
+- operating-points-v2: Phandle to the operating-points-v2 table to use.
+
+In 'operating-points-v2' table:
+- compatible: Should be
+ - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996.
+- nvmem-cells: A phandle pointing to a nvmem-cells node representing the
+ efuse registers that has information about the
+ speedbin that is used to select the right frequency/voltage
+ value pair.
+ Please refer the for nvmem-cells
+ bindings Documentation/devicetree/bindings/nvmem/nvmem.txt
+ and also examples below.
+
+In every OPP node:
+- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW.
+ Bitmap:
+ 0: MSM8996 V3, speedbin 0
+ 1: MSM8996 V3, speedbin 1
+ 2: MSM8996 V3, speedbin 2
+ 3: unused
+ 4: MSM8996 SG, speedbin 0
+ 5: MSM8996 SG, speedbin 1
+ 6: MSM8996 SG, speedbin 2
+ 7-31: unused
+
+Example 1:
+---------
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu@0 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU1: cpu@1 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU2: cpu@100 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU3: cpu@101 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_1>;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&CPU2>;
+ };
+
+ core1 {
+ cpu = <&CPU3>;
+ };
+ };
+ };
+ };
+
+ cluster0_opp: opp_table0 {
+ compatible = "operating-points-v2-kryo-cpu";
+ nvmem-cells = <&speedbin_efuse>;
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-422400000 {
+ opp-hz = /bits/ 64 <422400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-768000000 {
+ opp-hz = /bits/ 64 <768000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-844800000 {
+ opp-hz = /bits/ 64 <844800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-960000000 {
+ opp-hz = /bits/ 64 <960000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1228800000 {
+ opp-hz = /bits/ 64 <1228800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x72>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1497600000 {
+ opp-hz = /bits/ 64 <1497600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x4>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x20>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2188800000 {
+ opp-hz = /bits/ 64 <2188800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+ cluster1_opp: opp_table1 {
+ compatible = "operating-points-v2-kryo-cpu";
+ nvmem-cells = <&speedbin_efuse>;
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-403200000 {
+ opp-hz = /bits/ 64 <403200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-748800000 {
+ opp-hz = /bits/ 64 <748800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-806400000 {
+ opp-hz = /bits/ 64 <806400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-825600000 {
+ opp-hz = /bits/ 64 <825600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-883200000 {
+ opp-hz = /bits/ 64 <883200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-940800000 {
+ opp-hz = /bits/ 64 <940800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1248000000 {
+ opp-hz = /bits/ 64 <1248000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1555200000 {
+ opp-hz = /bits/ 64 <1555200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1632000000 {
+ opp-hz = /bits/ 64 <1632000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1670400000 {
+ opp-hz = /bits/ 64 <1670400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1708800000 {
+ opp-hz = /bits/ 64 <1708800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1747200000 {
+ opp-hz = /bits/ 64 <1747200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1785600000 {
+ opp-hz = /bits/ 64 <1785600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1804800000 {
+ opp-hz = /bits/ 64 <1804800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x6>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1824000000 {
+ opp-hz = /bits/ 64 <1824000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1900800000 {
+ opp-hz = /bits/ 64 <1900800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x74>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1920000000 {
+ opp-hz = /bits/ 64 <1920000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1977600000 {
+ opp-hz = /bits/ 64 <1977600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x30>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2054400000 {
+ opp-hz = /bits/ 64 <2054400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x30>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2073600000 {
+ opp-hz = /bits/ 64 <2073600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2150400000 {
+ opp-hz = /bits/ 64 <2150400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x31>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2246400000 {
+ opp-hz = /bits/ 64 <2246400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2342400000 {
+ opp-hz = /bits/ 64 <2342400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+....
+
+reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+....
+ smem_mem: smem-mem@86000000 {
+ reg = <0x0 0x86000000 0x0 0x200000>;
+ no-map;
+ };
+....
+};
+
+smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem_mem>;
+ hwlocks = <&tcsr_mutex 3>;
+};
+
+soc {
+....
+ qfprom: qfprom@74000 {
+ compatible = "qcom,qfprom";
+ reg = <0x00074000 0x8ff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ....
+ speedbin_efuse: speedbin@133 {
+ reg = <0x133 0x1>;
+ bits = <5 3>;
+ };
+ };
+};
--
1.9.1
In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
the CPU frequency subset and voltage value of each OPP varies
based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
defines the voltage and frequency value based on the msm-id in SMEM
and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.
Signed-off-by: Ilia Lin <[email protected]>
---
MAINTAINERS | 7 ++
drivers/cpufreq/Kconfig.arm | 10 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/cpufreq-dt-platdev.c | 3 +
drivers/cpufreq/qcom-cpufreq-kryo.c | 212 +++++++++++++++++++++++++++++++++++
5 files changed, 233 insertions(+)
create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
diff --git a/MAINTAINERS b/MAINTAINERS
index ba0adcb..648e0c8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11687,6 +11687,13 @@ F: Documentation/devicetree/bindings/media/qcom,camss.txt
F: Documentation/media/v4l-drivers/qcom_camss.rst
F: drivers/media/platform/qcom/camss-8x16/
+QUALCOMM CPUFREQ DRIVER MSM8996/APQ8096
+M: Ilia Lin <[email protected]>
+L: [email protected]
+S: Maintained
+F: Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
+F: drivers/cpufreq/qcom-cpufreq-kryo.c
+
QUALCOMM EMAC GIGABIT ETHERNET DRIVER
M: Timur Tabi <[email protected]>
L: [email protected]
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index de55c7d..0bfd40e 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -124,6 +124,16 @@ config ARM_OMAP2PLUS_CPUFREQ
depends on ARCH_OMAP2PLUS
default ARCH_OMAP2PLUS
+config ARM_QCOM_CPUFREQ_KRYO
+ bool "Qualcomm Kryo based CPUFreq"
+ depends on QCOM_QFPROM
+ depends on QCOM_SMEM
+ select PM_OPP
+ help
+ This adds the CPUFreq driver for Qualcomm Kryo SoC based boards.
+
+ If in doubt, say N.
+
config ARM_S3C_CPUFREQ
bool
help
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 8d24ade..fb4a2ec 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += mvebu-cpufreq.o
obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o
obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o
obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o
+obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq-kryo.o
obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o
obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o
obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o
diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index 3b585e4..77d6ab8 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -118,6 +118,9 @@
{ .compatible = "nvidia,tegra124", },
+ { .compatible = "qcom,apq8096", },
+ { .compatible = "qcom,msm8996", },
+
{ .compatible = "st,stih407", },
{ .compatible = "st,stih410", },
diff --git a/drivers/cpufreq/qcom-cpufreq-kryo.c b/drivers/cpufreq/qcom-cpufreq-kryo.c
new file mode 100644
index 0000000..d049fe4
--- /dev/null
+++ b/drivers/cpufreq/qcom-cpufreq-kryo.c
@@ -0,0 +1,212 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+/*
+ * In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
+ * the CPU frequency subset and voltage value of each OPP varies
+ * based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
+ * defines the voltage and frequency value based on the msm-id in SMEM
+ * and speedbin blown in the efuse combination.
+ * The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
+ * to provide the OPP framework with required information.
+ * This is used to determine the voltage and frequency value for each OPP of
+ * operating-points-v2 table when it is parsed by the OPP framework.
+ */
+
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+#include <linux/soc/qcom/smem.h>
+
+#define MSM_ID_SMEM 137
+
+enum _msm_id {
+ MSM8996V3 = 0xF6ul,
+ APQ8096V3 = 0x123ul,
+ MSM8996SG = 0x131ul,
+ APQ8096SG = 0x138ul,
+};
+
+enum _msm8996_version {
+ MSM8996_V3,
+ MSM8996_SG,
+ NUM_OF_MSM8996_VERSIONS,
+};
+
+static enum _msm8996_version __init qcom_cpufreq_kryo_get_msm_id(void)
+{
+ size_t len;
+ u32 *msm_id;
+ enum _msm8996_version version;
+
+ msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, MSM_ID_SMEM, &len);
+ if (IS_ERR(msm_id))
+ return NUM_OF_MSM8996_VERSIONS;
+
+ /* The first 4 bytes are format, next to them is the actual msm-id */
+ msm_id++;
+
+ switch ((enum _msm_id)*msm_id) {
+ case MSM8996V3:
+ case APQ8096V3:
+ version = MSM8996_V3;
+ break;
+ case MSM8996SG:
+ case APQ8096SG:
+ version = MSM8996_SG;
+ break;
+ default:
+ version = NUM_OF_MSM8996_VERSIONS;
+ }
+
+ return version;
+}
+
+static int qcom_cpufreq_kryo_probe(struct platform_device *pdev)
+{
+ struct opp_table *opp_tables[NR_CPUS] = {0};
+ struct platform_device *cpufreq_dt_pdev;
+ enum _msm8996_version msm8996_version;
+ struct nvmem_cell *speedbin_nvmem;
+ struct device_node *np;
+ struct device *cpu_dev;
+ unsigned cpu;
+ u8 *speedbin;
+ u32 versions;
+ size_t len;
+ int ret;
+
+ cpu_dev = get_cpu_device(0);
+ if (NULL == cpu_dev)
+ ret = -ENODEV;
+
+ msm8996_version = qcom_cpufreq_kryo_get_msm_id();
+ if (NUM_OF_MSM8996_VERSIONS == msm8996_version) {
+ dev_err(cpu_dev, "Not Snapdragon 820/821!");
+ return -ENODEV;
+ }
+
+ np = dev_pm_opp_of_get_opp_desc_node(cpu_dev);
+ if (IS_ERR(np))
+ return PTR_ERR(np);
+
+ ret = of_device_is_compatible(np, "operating-points-v2-kryo-cpu");
+ if (!ret) {
+ of_node_put(np);
+ return -ENOENT;
+ }
+
+ speedbin_nvmem = of_nvmem_cell_get(np, NULL);
+ of_node_put(np);
+ if (IS_ERR(speedbin_nvmem)) {
+ dev_err(cpu_dev, "Could not get nvmem cell: %ld\n",
+ PTR_ERR(speedbin_nvmem));
+ return PTR_ERR(speedbin_nvmem);
+ }
+
+ speedbin = nvmem_cell_read(speedbin_nvmem, &len);
+ nvmem_cell_put(speedbin_nvmem);
+
+ switch (msm8996_version) {
+ case MSM8996_V3:
+ versions = 1 << (unsigned int)(*speedbin);
+ break;
+ case MSM8996_SG:
+ versions = 1 << ((unsigned int)(*speedbin) + 4);
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ for_each_possible_cpu(cpu) {
+ cpu_dev = get_cpu_device(cpu);
+ if (NULL == cpu_dev) {
+ ret = -ENODEV;
+ goto free_opp;
+ }
+
+ opp_tables[cpu] = dev_pm_opp_set_supported_hw(cpu_dev,
+ &versions, 1);
+ if (IS_ERR(opp_tables[cpu])) {
+ ret = PTR_ERR(opp_tables[cpu]);
+ dev_err(cpu_dev, "Failed to set supported hardware\n");
+ goto free_opp;
+ }
+ }
+
+ cpufreq_dt_pdev = platform_device_register_simple("cpufreq-dt", -1,
+ NULL, 0);
+ if (!IS_ERR(cpufreq_dt_pdev))
+ return 0;
+
+ ret = PTR_ERR(cpufreq_dt_pdev);
+ dev_err(cpu_dev, "Failed to register platform device\n");
+
+free_opp:
+ for_each_possible_cpu(cpu) {
+ if (IS_ERR_OR_NULL(opp_tables[cpu]))
+ break;
+ dev_pm_opp_put_supported_hw(opp_tables[cpu]);
+ }
+
+ return ret;
+}
+
+static struct platform_driver qcom_cpufreq_kryo_driver = {
+ .probe = qcom_cpufreq_kryo_probe,
+ .driver = {
+ .name = "qcom-cpufreq-kryo",
+ },
+};
+
+static const struct of_device_id qcom_cpufreq_kryo_match_list[] __initconst = {
+ { .compatible = "qcom,apq8096", },
+ { .compatible = "qcom,msm8996", },
+};
+
+/*
+ * Since the driver depends on smem and nvmem drivers, which may
+ * return EPROBE_DEFER, all the real activity is done in the probe,
+ * which may be defered as well. The init here is only registering
+ * the driver and the platform device.
+ */
+static int __init qcom_cpufreq_kryo_init(void)
+{
+ struct device_node *np = of_find_node_by_path("/");
+ const struct of_device_id *match;
+ int ret;
+
+ if (!np)
+ return -ENODEV;
+
+ match = of_match_node(qcom_cpufreq_kryo_match_list, np);
+ of_node_put(np);
+ if (!match)
+ return -ENODEV;
+
+ ret = platform_driver_register(&qcom_cpufreq_kryo_driver);
+ if (unlikely(ret < 0))
+ return ret;
+
+ ret = PTR_ERR_OR_ZERO(platform_device_register_simple(
+ "qcom-cpufreq-kryo", -1, NULL, 0));
+ if (0 == ret)
+ return 0;
+
+ platform_driver_unregister(&qcom_cpufreq_kryo_driver);
+ return ret;
+}
+module_init(qcom_cpufreq_kryo_init);
+
+MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
On 25-05-18, 15:41, Ilia Lin wrote:
> In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
> the CPU frequency subset and voltage value of each OPP varies
> based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
> defines the voltage and frequency value based on the msm-id in SMEM
> and speedbin blown in the efuse combination.
> The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
> to provide the OPP framework with required information.
> This is used to determine the voltage and frequency value for each OPP of
> operating-points-v2 table when it is parsed by the OPP framework.
>
> Signed-off-by: Ilia Lin <[email protected]>
> ---
> MAINTAINERS | 7 ++
> drivers/cpufreq/Kconfig.arm | 10 ++
> drivers/cpufreq/Makefile | 1 +
> drivers/cpufreq/cpufreq-dt-platdev.c | 3 +
> drivers/cpufreq/qcom-cpufreq-kryo.c | 212 +++++++++++++++++++++++++++++++++++
> 5 files changed, 233 insertions(+)
> create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
Acked-by: Viresh Kumar <[email protected]>
--
viresh