Add ZynqMP PM driver. PM driver provides power management
support for ZynqMP.
This patch series is based on top of Xilinx firmware patch set:
https://patchwork.kernel.org/cover/10598195/
v4:
- Minor fixes to address v3 review comments
v3:
- Updated DT bindings as per v2 review comments
v2:
- Rebased on top of latest firmware driver patch series
- Updated driver to use shared interrupt instead of mailbox
Rajan Vaja (3):
dt-bindings: soc: Add ZynqMP PM bindings
firmware: xilinx: Implement ZynqMP power management APIs
drivers: soc: xilinx: Add ZynqMP PM driver
.../bindings/power/reset/xlnx,zynqmp-power.txt | 22 +++
drivers/firmware/xilinx/zynqmp.c | 29 ++++
drivers/soc/xilinx/Kconfig | 11 ++
drivers/soc/xilinx/Makefile | 1 +
drivers/soc/xilinx/zynqmp_power.c | 178 +++++++++++++++++++++
include/linux/firmware/xlnx-zynqmp.h | 20 +++
6 files changed, 261 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
create mode 100644 drivers/soc/xilinx/zynqmp_power.c
--
2.7.4
From: Rajan Vaja <[email protected]>
Add documentation to describe Xilinx ZynqMP power management
bindings.
Signed-off-by: Rajan Vaja <[email protected]>
Signed-off-by: Jolly Shah <[email protected]>
---
.../bindings/power/reset/xlnx,zynqmp-power.txt | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
diff --git a/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt b/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
new file mode 100644
index 0000000..925d17d
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
@@ -0,0 +1,22 @@
+--------------------------------------------------------------------
+Device Tree Bindings for the Xilinx Zynq MPSoC Power Management
+--------------------------------------------------------------------
+The zynqmp-power node describes the power management configurations.
+It will control remote suspend/shutdown interfaces.
+
+Required properties:
+ - compatible: Must contain: "xlnx,zynqmp-power"
+ - interrupts: Interrupt specifier
+
+-------
+Example
+-------
+
+firmware {
+ zynqmp_firmware: zynqmp-firmware {
+ zynqmp_power: zynqmp-power {
+ compatible = "xlnx,zynqmp-power";
+ interrupts = <0 35 4>;
+ };
+ };
+};
--
2.7.4
From: Rajan Vaja <[email protected]>
Add ZynqMP PM driver. PM driver provides power management
support for ZynqMP.
Signed-off-by: Rajan Vaja <[email protected]>
Signed-off-by: Jolly Shah <[email protected]>
---
drivers/soc/xilinx/Kconfig | 11 +++
drivers/soc/xilinx/Makefile | 1 +
drivers/soc/xilinx/zynqmp_power.c | 178 ++++++++++++++++++++++++++++++++++++++
3 files changed, 190 insertions(+)
create mode 100644 drivers/soc/xilinx/zynqmp_power.c
diff --git a/drivers/soc/xilinx/Kconfig b/drivers/soc/xilinx/Kconfig
index 687c8f3..5025e0e 100644
--- a/drivers/soc/xilinx/Kconfig
+++ b/drivers/soc/xilinx/Kconfig
@@ -17,4 +17,15 @@ config XILINX_VCU
To compile this driver as a module, choose M here: the
module will be called xlnx_vcu.
+config ZYNQMP_POWER
+ bool "Enable Xilinx Zynq MPSoC Power Management driver"
+ depends on PM && ARCH_ZYNQMP
+ default y
+ help
+ Say yes to enable power management support for ZyqnMP SoC.
+ This driver uses firmware driver as an interface for power
+ management request to firmware. It registers isr to handle
+ power management callbacks from firmware.
+ If in doubt, say N.
+
endmenu
diff --git a/drivers/soc/xilinx/Makefile b/drivers/soc/xilinx/Makefile
index dee8fd5..428b9db 100644
--- a/drivers/soc/xilinx/Makefile
+++ b/drivers/soc/xilinx/Makefile
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0
obj-$(CONFIG_XILINX_VCU) += xlnx_vcu.o
+obj-$(CONFIG_ZYNQMP_POWER) += zynqmp_power.o
diff --git a/drivers/soc/xilinx/zynqmp_power.c b/drivers/soc/xilinx/zynqmp_power.c
new file mode 100644
index 0000000..771cb59
--- /dev/null
+++ b/drivers/soc/xilinx/zynqmp_power.c
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Xilinx Zynq MPSoC Power Management
+ *
+ * Copyright (C) 2014-2018 Xilinx, Inc.
+ *
+ * Davorin Mista <[email protected]>
+ * Jolly Shah <[email protected]>
+ * Rajan Vaja <[email protected]>
+ */
+
+#include <linux/mailbox_client.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/reboot.h>
+#include <linux/suspend.h>
+
+#include <linux/firmware/xlnx-zynqmp.h>
+
+enum pm_suspend_mode {
+ PM_SUSPEND_MODE_FIRST = 0,
+ PM_SUSPEND_MODE_STD = PM_SUSPEND_MODE_FIRST,
+ PM_SUSPEND_MODE_POWER_OFF,
+};
+
+#define PM_SUSPEND_MODE_FIRST PM_SUSPEND_MODE_STD
+
+static const char *const suspend_modes[] = {
+ [PM_SUSPEND_MODE_STD] = "standard",
+ [PM_SUSPEND_MODE_POWER_OFF] = "power-off",
+};
+
+static enum pm_suspend_mode suspend_mode = PM_SUSPEND_MODE_STD;
+
+enum pm_api_cb_id {
+ PM_INIT_SUSPEND_CB = 30,
+ PM_ACKNOWLEDGE_CB,
+ PM_NOTIFY_CB,
+};
+
+static void zynqmp_pm_get_callback_data(u32 *buf)
+{
+ zynqmp_pm_invoke_fn(GET_CALLBACK_DATA, 0, 0, 0, 0, buf);
+}
+
+static irqreturn_t zynqmp_pm_isr(int irq, void *data)
+{
+ u32 payload[CB_PAYLOAD_SIZE];
+
+ zynqmp_pm_get_callback_data(payload);
+
+ /* First element is callback API ID, others are callback arguments */
+ if (payload[0] == PM_INIT_SUSPEND_CB) {
+ switch (payload[1]) {
+ case SUSPEND_SYSTEM_SHUTDOWN:
+ orderly_poweroff(true);
+ break;
+ case SUSPEND_POWER_REQUEST:
+ pm_suspend(PM_SUSPEND_MEM);
+ break;
+ default:
+ pr_err("%s Unsupported InitSuspendCb reason "
+ "code %d\n", __func__, payload[1]);
+ }
+ }
+
+ return IRQ_HANDLED;
+}
+
+static ssize_t suspend_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ char *s = buf;
+ int md;
+
+ for (md = PM_SUSPEND_MODE_FIRST; md < ARRAY_SIZE(suspend_modes); md++)
+ if (suspend_modes[md]) {
+ if (md == suspend_mode)
+ s += sprintf(s, "[%s] ", suspend_modes[md]);
+ else
+ s += sprintf(s, "%s ", suspend_modes[md]);
+ }
+
+ /* Convert last space to newline */
+ if (s != buf)
+ *(s - 1) = '\n';
+ return (s - buf);
+}
+
+static ssize_t suspend_mode_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ int md, ret = -EINVAL;
+ const struct zynqmp_eemi_ops *eemi_ops = zynqmp_pm_get_eemi_ops();
+
+ if (!eemi_ops || !eemi_ops->set_suspend_mode)
+ return ret;
+
+ for (md = PM_SUSPEND_MODE_FIRST; md < ARRAY_SIZE(suspend_modes); md++)
+ if (suspend_modes[md] &&
+ sysfs_streq(suspend_modes[md], buf)) {
+ ret = 0;
+ break;
+ }
+
+ if (!ret && md != suspend_mode) {
+ ret = eemi_ops->set_suspend_mode(md);
+ if (likely(!ret))
+ suspend_mode = md;
+ }
+
+ return ret ? ret : count;
+}
+
+static DEVICE_ATTR_RW(suspend_mode);
+
+static int zynqmp_pm_probe(struct platform_device *pdev)
+{
+ int ret, irq;
+ u32 pm_api_version;
+
+ const struct zynqmp_eemi_ops *eemi_ops = zynqmp_pm_get_eemi_ops();
+
+ if (!eemi_ops || !eemi_ops->get_api_version || !eemi_ops->init_finalize)
+ return -ENXIO;
+
+ eemi_ops->init_finalize();
+ eemi_ops->get_api_version(&pm_api_version);
+
+ /* Check PM API version number */
+ if (pm_api_version < ZYNQMP_PM_VERSION)
+ return -ENODEV;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq <= 0)
+ return -ENXIO;
+
+ ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, zynqmp_pm_isr,
+ IRQF_NO_SUSPEND | IRQF_ONESHOT,
+ dev_name(&pdev->dev), &pdev->dev);
+ if (ret) {
+ dev_err(&pdev->dev, "devm_request_threaded_irq '%d' failed "
+ "with %d\n", irq, ret);
+ return ret;
+ }
+
+ ret = sysfs_create_file(&pdev->dev.kobj, &dev_attr_suspend_mode.attr);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to create sysfs interface\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int zynqmp_pm_remove(struct platform_device *pdev)
+{
+ sysfs_remove_file(&pdev->dev.kobj, &dev_attr_suspend_mode.attr);
+
+ return 0;
+}
+
+static const struct of_device_id pm_of_match[] = {
+ { .compatible = "xlnx,zynqmp-power", },
+ { /* end of table */ },
+};
+MODULE_DEVICE_TABLE(of, pm_of_match);
+
+static struct platform_driver zynqmp_pm_platform_driver = {
+ .probe = zynqmp_pm_probe,
+ .remove = zynqmp_pm_remove,
+ .driver = {
+ .name = "zynqmp_power",
+ .of_match_table = pm_of_match,
+ },
+};
+module_platform_driver(zynqmp_pm_platform_driver);
--
2.7.4
From: Rajan Vaja <[email protected]>
Add Xilinx ZynqMP firmware APIs to set suspend mode
and inform firmware that master has initialized its
own power management.
Signed-off-by: Rajan Vaja <[email protected]>
Signed-off-by: Jolly Shah <[email protected]>
---
drivers/firmware/xilinx/zynqmp.c | 29 +++++++++++++++++++++++++++++
include/linux/firmware/xlnx-zynqmp.h | 20 ++++++++++++++++++++
2 files changed, 49 insertions(+)
diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
index 84b3fd2..c7a3b6c 100644
--- a/drivers/firmware/xilinx/zynqmp.c
+++ b/drivers/firmware/xilinx/zynqmp.c
@@ -428,6 +428,33 @@ static int zynqmp_pm_clock_getparent(u32 clock_id, u32 *parent_id)
return ret;
}
+/**
+ * zynqmp_pm_init_finalize() - PM call to inform firmware that the caller
+ * master has initialized its own power management
+ *
+ * This API function is to be used for notify the power management controller
+ * about the completed power management initialization.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+static int zynqmp_pm_init_finalize(void)
+{
+ return zynqmp_pm_invoke_fn(PM_PM_INIT_FINALIZE, 0, 0, 0, 0, NULL);
+}
+
+/**
+ * zynqmp_pm_set_suspend_mode() - Set system suspend mode
+ * @mode: Mode to set for system suspend
+ *
+ * This API function is used to set mode of system suspend.
+ *
+ * Return: Returns status, either success or error+reason
+ */
+static int zynqmp_pm_set_suspend_mode(u32 mode)
+{
+ return zynqmp_pm_invoke_fn(PM_SET_SUSPEND_MODE, mode, 0, 0, 0, NULL);
+}
+
static const struct zynqmp_eemi_ops eemi_ops = {
.get_api_version = zynqmp_pm_get_api_version,
.query_data = zynqmp_pm_query_data,
@@ -440,6 +467,8 @@ static const struct zynqmp_eemi_ops eemi_ops = {
.clock_getrate = zynqmp_pm_clock_getrate,
.clock_setparent = zynqmp_pm_clock_setparent,
.clock_getparent = zynqmp_pm_clock_getparent,
+ .init_finalize = zynqmp_pm_init_finalize,
+ .set_suspend_mode = zynqmp_pm_set_suspend_mode,
};
/**
diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
index 015e130..1424170 100644
--- a/include/linux/firmware/xlnx-zynqmp.h
+++ b/include/linux/firmware/xlnx-zynqmp.h
@@ -28,12 +28,21 @@
/* SMC SIP service Call Function Identifier Prefix */
#define PM_SIP_SVC 0xC2000000
#define PM_GET_TRUSTZONE_VERSION 0xa03
+#define PM_SET_SUSPEND_MODE 0xa02
+#define GET_CALLBACK_DATA 0xa01
/* Number of 32bits values in payload */
#define PAYLOAD_ARG_CNT 4U
+/* Number of arguments for a callback */
+#define CB_ARG_CNT 4
+
+/* Payload size (consists of callback API ID + arguments) */
+#define CB_PAYLOAD_SIZE (CB_ARG_CNT + 1)
+
enum pm_api_id {
PM_GET_API_VERSION = 1,
+ PM_PM_INIT_FINALIZE = 21,
PM_QUERY_DATA = 35,
PM_CLOCK_ENABLE,
PM_CLOCK_DISABLE,
@@ -73,6 +82,12 @@ enum pm_query_id {
PM_QID_CLOCK_GET_ATTRIBUTES,
};
+enum zynqmp_pm_suspend_reason {
+ SUSPEND_POWER_REQUEST = 201,
+ SUSPEND_ALERT,
+ SUSPEND_SYSTEM_SHUTDOWN,
+};
+
/**
* struct zynqmp_pm_query_data - PM query data
* @qid: query ID
@@ -99,8 +114,13 @@ struct zynqmp_eemi_ops {
int (*clock_getrate)(u32 clock_id, u64 *rate);
int (*clock_setparent)(u32 clock_id, u32 parent_id);
int (*clock_getparent)(u32 clock_id, u32 *parent_id);
+ int (*init_finalize)(void);
+ int (*set_suspend_mode)(u32 mode);
};
+int zynqmp_pm_invoke_fn(u32 pm_api_id, u32 arg0, u32 arg1,
+ u32 arg2, u32 arg3, u32 *ret_payload);
+
#if IS_REACHABLE(CONFIG_ARCH_ZYNQMP)
const struct zynqmp_eemi_ops *zynqmp_pm_get_eemi_ops(void);
#else
--
2.7.4
Ping for comments
> -----Original Message-----
> From: [email protected] [mailto:linux-kernel-
> [email protected]] On Behalf Of Jolly Shah
> Sent: Friday, September 14, 2018 12:40 PM
> To: [email protected]; [email protected]; [email protected];
> [email protected]; [email protected];
> [email protected]; [email protected]; Michal Simek
> <[email protected]>; [email protected]; [email protected]
> Cc: Rajan Vaja <[email protected]>; [email protected]; linux-arm-
> [email protected]; [email protected]; Jolly Shah
> <[email protected]>
> Subject: [PATCH v4 0/3] drivers: soc: xilinx: Add support for ZynqMP PM driver
>
> Add ZynqMP PM driver. PM driver provides power management support for
> ZynqMP.
>
> This patch series is based on top of Xilinx firmware patch set:
> https://patchwork.kernel.org/cover/10598195/
>
> v4:
> - Minor fixes to address v3 review comments
>
> v3:
> - Updated DT bindings as per v2 review comments
>
> v2:
> - Rebased on top of latest firmware driver patch series
> - Updated driver to use shared interrupt instead of mailbox
>
> Rajan Vaja (3):
> dt-bindings: soc: Add ZynqMP PM bindings
> firmware: xilinx: Implement ZynqMP power management APIs
> drivers: soc: xilinx: Add ZynqMP PM driver
>
> .../bindings/power/reset/xlnx,zynqmp-power.txt | 22 +++
> drivers/firmware/xilinx/zynqmp.c | 29 ++++
> drivers/soc/xilinx/Kconfig | 11 ++
> drivers/soc/xilinx/Makefile | 1 +
> drivers/soc/xilinx/zynqmp_power.c | 178 +++++++++++++++++++++
> include/linux/firmware/xlnx-zynqmp.h | 20 +++
> 6 files changed, 261 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt
> create mode 100644 drivers/soc/xilinx/zynqmp_power.c
>
> --
> 2.7.4