On Tue, Feb 19, 2019 at 03:36:30PM +0800, [email protected] wrote:
> From: Min Guo <[email protected]>
>
> This adds support for MediaTek musb controller in
> host, peripheral and otg mode.
>
> Signed-off-by: Min Guo <[email protected]>
> ---
> changes in v5:
> suggested by Rob:
> 1. Modify compatible as
> - compatible : should be one of:
> "mediatek,mt-2701"
> ...
> followed by "mediatek,mtk-musb"
> 2. Add usb connector child node
>
> changes in v4:
> suggested by Sergei:
> 1. String alignment
>
> changes in v3:
> 1. no changes
>
> changes in v2:
> suggested by Bin:
> 1. Modify DRC to DRD
> suggested by Rob:
> 2. Drop the "<soc-model>-musb" in compatible
> 3. Remove phy-names
> 4. Add space after comma in clock-names
> ---
> .../devicetree/bindings/usb/mediatek,musb.txt | 54 ++++++++++++++++++++++
> 1 file changed, 54 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/mediatek,musb.txt
>
> diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> new file mode 100644
> index 0000000..0632e6e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> @@ -0,0 +1,54 @@
> +MediaTek musb DRD/OTG controller
> +-------------------------------------------
> +
> +Required properties:
> + - compatible : should be one of:
> + "mediatek,mt-2701"
That looks like a top-level SoC compatible and doesn't match the
example.
> + ...
> + followed by "mediatek,mtk-musb"
> + - reg : specifies physical base address and size of
> + the registers
> + - interrupts : interrupt used by musb controller
> + - interrupt-names : must be "mc"
Not much point in a name when there is only 1.
> + - phys : PHY specifier for the OTG phy
> + - dr_mode : should be one of "host", "peripheral" or "otg",
> + refer to usb/generic.txt
> + - clocks : a list of phandle + clock-specifier pairs, one for
> + each entry in clock-names
> + - clock-names : must contain "main", "mcu", "univpll"
> + for clocks of controller
> +
> +Optional properties:
> + - power-domains : a phandle to USB power domain node to control USB's
> + MTCMOS
> +
> +Required child nodes:
> + usb connector node as defined in bindings/connector/usb-connector.txt
> + - extcon : for VBUS and ID pin changes detection, needed when
> + supports dual-role mode
> + - vbus-supply : reference to the VBUS regulator, needed when supports
> + dual-role mode
> +
> +Example:
> +
> +usb2: usb@11200000 {
> + compatible = "mediatek,mt2701-musb",
> + "mediatek,mtk-musb";
> + reg = <0 0x11200000 0 0x1000>;
> + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-names = "mc";
> + phys = <&u2port2 PHY_TYPE_USB2>;
> + dr_mode = "otg";
> + clocks = <&pericfg CLK_PERI_USB0>,
> + <&pericfg CLK_PERI_USB0_MCU>,
> + <&pericfg CLK_PERI_USB_SLV>;
> + clock-names = "main","mcu","univpll";
> + power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
> + usb_con: connector{
> + compatible = "usb-b-connector";
> + label = "micro-USB";
> + type = "micro";
> + extcon = <&extcon_usb>;
The connector node should replace 'extcon'. Add what you need here
directly (e.g. id-gpios). What you add needs to be defined in
usb-connector.txt.
> + vbus-supply = <&usb_vbus>;
> + };
> +};
> --
> 1.9.1
>
Hi Rob,
On Fri, 2019-02-22 at 10:49 -0600, Rob Herring wrote:
> On Tue, Feb 19, 2019 at 03:36:30PM +0800, [email protected] wrote:
> > From: Min Guo <[email protected]>
> >
> > This adds support for MediaTek musb controller in
> > host, peripheral and otg mode.
> >
> > Signed-off-by: Min Guo <[email protected]>
> > ---
> > changes in v5:
> > suggested by Rob:
> > 1. Modify compatible as
> > - compatible : should be one of:
> > "mediatek,mt-2701"
> > ...
> > followed by "mediatek,mtk-musb"
> > 2. Add usb connector child node
> >
> > changes in v4:
> > suggested by Sergei:
> > 1. String alignment
> >
> > changes in v3:
> > 1. no changes
> >
> > changes in v2:
> > suggested by Bin:
> > 1. Modify DRC to DRD
> > suggested by Rob:
> > 2. Drop the "<soc-model>-musb" in compatible
> > 3. Remove phy-names
> > 4. Add space after comma in clock-names
> > ---
> > .../devicetree/bindings/usb/mediatek,musb.txt | 54 ++++++++++++++++++++++
> > 1 file changed, 54 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/usb/mediatek,musb.txt
> >
> > diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> > new file mode 100644
> > index 0000000..0632e6e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> > @@ -0,0 +1,54 @@
> > +MediaTek musb DRD/OTG controller
> > +-------------------------------------------
> > +
> > +Required properties:
> > + - compatible : should be one of:
> > + "mediatek,mt-2701"
>
> That looks like a top-level SoC compatible and doesn't match the
> example.
"mediatek,mt-2701" is an example, just to describe a specific SOC.
May I modify compatibel like:
compatible : should be "mediatek,mtk-musb"
> > + ...
> > + followed by "mediatek,mtk-musb"
> > + - reg : specifies physical base address and size of
> > + the registers
> > + - interrupts : interrupt used by musb controller
> > + - interrupt-names : must be "mc"
>
> Not much point in a name when there is only 1.
The MUSB core driver has two interrupts, one is for MAC, another for
DMA, but on MTK platform, there is only a MAC interrupt, musb core
driver uses platform_get_irq_byname(pdev, "mc") to get this interrupt
number.
> > + - phys : PHY specifier for the OTG phy
> > + - dr_mode : should be one of "host", "peripheral" or "otg",
> > + refer to usb/generic.txt
> > + - clocks : a list of phandle + clock-specifier pairs, one for
> > + each entry in clock-names
> > + - clock-names : must contain "main", "mcu", "univpll"
> > + for clocks of controller
> > +
> > +Optional properties:
> > + - power-domains : a phandle to USB power domain node to control USB's
> > + MTCMOS
> > +
> > +Required child nodes:
> > + usb connector node as defined in bindings/connector/usb-connector.txt
> > + - extcon : for VBUS and ID pin changes detection, needed when
> > + supports dual-role mode
> > + - vbus-supply : reference to the VBUS regulator, needed when supports
> > + dual-role mode
> > +
> > +Example:
> > +
> > +usb2: usb@11200000 {
> > + compatible = "mediatek,mt2701-musb",
> > + "mediatek,mtk-musb";
> > + reg = <0 0x11200000 0 0x1000>;
> > + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
> > + interrupt-names = "mc";
> > + phys = <&u2port2 PHY_TYPE_USB2>;
> > + dr_mode = "otg";
> > + clocks = <&pericfg CLK_PERI_USB0>,
> > + <&pericfg CLK_PERI_USB0_MCU>,
> > + <&pericfg CLK_PERI_USB_SLV>;
> > + clock-names = "main","mcu","univpll";
> > + power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
> > + usb_con: connector{
> > + compatible = "usb-b-connector";
> > + label = "micro-USB";
> > + type = "micro";
> > + extcon = <&extcon_usb>;
>
> The connector node should replace 'extcon'. Add what you need here
> directly (e.g. id-gpios). What you add needs to be defined in
> usb-connector.txt.
OK.
> > + vbus-supply = <&usb_vbus>;
> > + };
> > +};
> > --
> > 1.9.1
> >
Regards,
Min.
On Sun, Feb 24, 2019 at 7:36 PM Min Guo <[email protected]> wrote:
>
> Hi Rob,
> On Fri, 2019-02-22 at 10:49 -0600, Rob Herring wrote:
> > On Tue, Feb 19, 2019 at 03:36:30PM +0800, [email protected] wrote:
> > > From: Min Guo <[email protected]>
> > >
> > > This adds support for MediaTek musb controller in
> > > host, peripheral and otg mode.
> > >
> > > Signed-off-by: Min Guo <[email protected]>
> > > ---
> > > changes in v5:
> > > suggested by Rob:
> > > 1. Modify compatible as
> > > - compatible : should be one of:
> > > "mediatek,mt-2701"
> > > ...
> > > followed by "mediatek,mtk-musb"
> > > 2. Add usb connector child node
> > >
> > > changes in v4:
> > > suggested by Sergei:
> > > 1. String alignment
> > >
> > > changes in v3:
> > > 1. no changes
> > >
> > > changes in v2:
> > > suggested by Bin:
> > > 1. Modify DRC to DRD
> > > suggested by Rob:
> > > 2. Drop the "<soc-model>-musb" in compatible
> > > 3. Remove phy-names
> > > 4. Add space after comma in clock-names
> > > ---
> > > .../devicetree/bindings/usb/mediatek,musb.txt | 54 ++++++++++++++++++++++
> > > 1 file changed, 54 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/usb/mediatek,musb.txt
> > >
> > > diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> > > new file mode 100644
> > > index 0000000..0632e6e
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> > > @@ -0,0 +1,54 @@
> > > +MediaTek musb DRD/OTG controller
> > > +-------------------------------------------
> > > +
> > > +Required properties:
> > > + - compatible : should be one of:
> > > + "mediatek,mt-2701"
> >
> > That looks like a top-level SoC compatible and doesn't match the
> > example.
> "mediatek,mt-2701" is an example, just to describe a specific SOC.
> May I modify compatibel like:
> compatible : should be "mediatek,mtk-musb"
No, you should fix the example adding "mediatek,mtk-musb".
Rob
Hi Rob,
On Mon, 2019-03-04 at 11:42 -0600, Rob Herring wrote:
> On Sun, Feb 24, 2019 at 7:36 PM Min Guo <[email protected]> wrote:
> >
> > Hi Rob,
> > On Fri, 2019-02-22 at 10:49 -0600, Rob Herring wrote:
> > > On Tue, Feb 19, 2019 at 03:36:30PM +0800, [email protected] wrote:
> > > > From: Min Guo <[email protected]>
> > > >
> > > > This adds support for MediaTek musb controller in
> > > > host, peripheral and otg mode.
> > > >
> > > > Signed-off-by: Min Guo <[email protected]>
> > > > ---
> > > > changes in v5:
> > > > suggested by Rob:
> > > > 1. Modify compatible as
> > > > - compatible : should be one of:
> > > > "mediatek,mt-2701"
> > > > ...
> > > > followed by "mediatek,mtk-musb"
> > > > 2. Add usb connector child node
> > > >
> > > > changes in v4:
> > > > suggested by Sergei:
> > > > 1. String alignment
> > > >
> > > > changes in v3:
> > > > 1. no changes
> > > >
> > > > changes in v2:
> > > > suggested by Bin:
> > > > 1. Modify DRC to DRD
> > > > suggested by Rob:
> > > > 2. Drop the "<soc-model>-musb" in compatible
> > > > 3. Remove phy-names
> > > > 4. Add space after comma in clock-names
> > > > ---
> > > > .../devicetree/bindings/usb/mediatek,musb.txt | 54 ++++++++++++++++++++++
> > > > 1 file changed, 54 insertions(+)
> > > > create mode 100644 Documentation/devicetree/bindings/usb/mediatek,musb.txt
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> > > > new file mode 100644
> > > > index 0000000..0632e6e
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
> > > > @@ -0,0 +1,54 @@
> > > > +MediaTek musb DRD/OTG controller
> > > > +-------------------------------------------
> > > > +
> > > > +Required properties:
> > > > + - compatible : should be one of:
> > > > + "mediatek,mt-2701"
> > >
> > > That looks like a top-level SoC compatible and doesn't match the
> > > example.
> > "mediatek,mt-2701" is an example, just to describe a specific SOC.
> > May I modify compatibel like:
> > compatible : should be "mediatek,mtk-musb"
>
> No, you should fix the example adding "mediatek,mtk-musb".
OK.
> Rob
Regards,
Min.