Replace the incorrect Cyrix-specific macro calls with the correct
setCx86() and getCx86() calls. Also remove the unused setCx86_old(),
getCx86_old() and their related comments in the code.
Matthew Whitehead (2):
x86/CPU: Use correct macros for Cyrix calls on Geode processors
x86/CPU: Remove {get,set}Cx86_old macros used for Cyrix processors
arch/x86/include/asm/processor-cyrix.h | 21 ---------------------
arch/x86/kernel/cpu/cyrix.c | 14 +++++++-------
2 files changed, 7 insertions(+), 28 deletions(-)
--
1.8.3.1
There are comments in processor-cyrix.h advising you to _not_ make calls
using the deprecated macros in this style:
setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x80);
This is because it expands the macro into a non-functioning calling
sequence. The calling order must be:
outb(CX86_CCR2, 0x22);
inb(0x23);
From the comments:
* When using the old macros a line like
* setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
* gets expanded to:
* do {
* outb((CX86_CCR2), 0x22);
* outb((({
* outb((CX86_CCR2), 0x22);
* inb(0x23);
* }) | 0x88), 0x23);
* } while (0);
The new macros fix this problem, so use them instead. Tested on an
actual Geode processor.
Signed-off-by: Matthew Whitehead <[email protected]>
---
arch/x86/kernel/cpu/cyrix.c | 14 +++++++-------
1 file changed, 7 insertions(+), 7 deletions(-)
diff --git a/arch/x86/kernel/cpu/cyrix.c b/arch/x86/kernel/cpu/cyrix.c
index d12226f..1d9b8aa 100644
--- a/arch/x86/kernel/cpu/cyrix.c
+++ b/arch/x86/kernel/cpu/cyrix.c
@@ -124,7 +124,7 @@ static void set_cx86_reorder(void)
setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */
/* Load/Store Serialize to mem access disable (=reorder it) */
- setCx86_old(CX86_PCR0, getCx86_old(CX86_PCR0) & ~0x80);
+ setCx86(CX86_PCR0, getCx86(CX86_PCR0) & ~0x80);
/* set load/store serialize from 1GB to 4GB */
ccr3 |= 0xe0;
setCx86(CX86_CCR3, ccr3);
@@ -135,11 +135,11 @@ static void set_cx86_memwb(void)
pr_info("Enable Memory-Write-back mode on Cyrix/NSC processor.\n");
/* CCR2 bit 2: unlock NW bit */
- setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) & ~0x04);
+ setCx86(CX86_CCR2, getCx86(CX86_CCR2) & ~0x04);
/* set 'Not Write-through' */
write_cr0(read_cr0() | X86_CR0_NW);
/* CCR2 bit 2: lock NW bit and set WT1 */
- setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) | 0x14);
+ setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x14);
}
/*
@@ -153,14 +153,14 @@ static void geode_configure(void)
local_irq_save(flags);
/* Suspend on halt power saving and enable #SUSP pin */
- setCx86_old(CX86_CCR2, getCx86_old(CX86_CCR2) | 0x88);
+ setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
ccr3 = getCx86(CX86_CCR3);
setCx86(CX86_CCR3, (ccr3 & 0x0f) | 0x10); /* enable MAPEN */
/* FPU fast, DTE cache, Mem bypass */
- setCx86_old(CX86_CCR4, getCx86_old(CX86_CCR4) | 0x38);
+ setCx86(CX86_CCR4, getCx86(CX86_CCR4) | 0x38);
setCx86(CX86_CCR3, ccr3); /* disable MAPEN */
set_cx86_memwb();
@@ -296,7 +296,7 @@ static void init_cyrix(struct cpuinfo_x86 *c)
/* GXm supports extended cpuid levels 'ala' AMD */
if (c->cpuid_level == 2) {
/* Enable cxMMX extensions (GX1 Datasheet 54) */
- setCx86_old(CX86_CCR7, getCx86_old(CX86_CCR7) | 1);
+ setCx86(CX86_CCR7, getCx86(CX86_CCR7) | 1);
/*
* GXm : 0x30 ... 0x5f GXm datasheet 51
@@ -319,7 +319,7 @@ static void init_cyrix(struct cpuinfo_x86 *c)
if (dir1 > 7) {
dir0_msn++; /* M II */
/* Enable MMX extensions (App note 108) */
- setCx86_old(CX86_CCR7, getCx86_old(CX86_CCR7)|1);
+ setCx86(CX86_CCR7, getCx86(CX86_CCR7)|1);
} else {
/* A 6x86MX - it has the bug. */
set_cpu_bug(c, X86_BUG_COMA);
--
1.8.3.1
The getCx86_old() and setCx86_old() macros have been replaced with
correctly working getCx86() and setCx86(), so remove these unused macros.
Signed-off-by: Matthew Whitehead <[email protected]>
---
arch/x86/include/asm/processor-cyrix.h | 21 ---------------------
1 file changed, 21 deletions(-)
diff --git a/arch/x86/include/asm/processor-cyrix.h b/arch/x86/include/asm/processor-cyrix.h
index aaedd73..df700a6 100644
--- a/arch/x86/include/asm/processor-cyrix.h
+++ b/arch/x86/include/asm/processor-cyrix.h
@@ -3,19 +3,6 @@
* NSC/Cyrix CPU indexed register access. Must be inlined instead of
* macros to ensure correct access ordering
* Access order is always 0x22 (=offset), 0x23 (=value)
- *
- * When using the old macros a line like
- * setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
- * gets expanded to:
- * do {
- * outb((CX86_CCR2), 0x22);
- * outb((({
- * outb((CX86_CCR2), 0x22);
- * inb(0x23);
- * }) | 0x88), 0x23);
- * } while (0);
- *
- * which in fact violates the access order (= 0x22, 0x22, 0x23, 0x23).
*/
static inline u8 getCx86(u8 reg)
@@ -29,11 +16,3 @@ static inline void setCx86(u8 reg, u8 data)
outb(reg, 0x22);
outb(data, 0x23);
}
-
-#define getCx86_old(reg) ({ outb((reg), 0x22); inb(0x23); })
-
-#define setCx86_old(reg, data) do { \
- outb((reg), 0x22); \
- outb((data), 0x23); \
-} while (0)
-
--
1.8.3.1