From: Thor Thayer <[email protected]>
Improve the Arria10 and Stratix10 error injection routine
by reading the data and changing just 1 bit before writing
back out. Previous routine would overwrite the first bytes
to 0 then change 1 bit but this method is less intrusive.
Signed-off-by: Thor Thayer <[email protected]>
---
drivers/edac/altera_edac.c | 30 +++++++++++++-----------------
drivers/edac/altera_edac.h | 2 +-
2 files changed, 14 insertions(+), 18 deletions(-)
diff --git a/drivers/edac/altera_edac.c b/drivers/edac/altera_edac.c
index 5ff263850cc7..acb3006df631 100644
--- a/drivers/edac/altera_edac.c
+++ b/drivers/edac/altera_edac.c
@@ -1762,28 +1762,24 @@ static ssize_t altr_edac_a10_device_trig2(struct file *file,
if (trig_type == ALTR_UE_TRIGGER_CHAR) {
writel(priv->ue_set_mask, set_addr);
} else {
- /* Setup write of 0 to first 4 bytes */
- writel(0x0, drvdata->base + ECC_BLK_WDATA0_OFST);
- writel(0x0, drvdata->base + ECC_BLK_WDATA1_OFST);
- writel(0x0, drvdata->base + ECC_BLK_WDATA2_OFST);
- writel(0x0, drvdata->base + ECC_BLK_WDATA3_OFST);
- /* Setup write of 4 bytes */
+ /* Setup read/write of 4 bytes */
writel(ECC_WORD_WRITE, drvdata->base + ECC_BLK_DBYTECTRL_OFST);
/* Setup Address to 0 */
- writel(0x0, drvdata->base + ECC_BLK_ADDRESS_OFST);
- /* Setup accctrl to write & data override */
- writel(ECC_WRITE_DOVR, drvdata->base + ECC_BLK_ACCCTRL_OFST);
- /* Kick it. */
- writel(ECC_XACT_KICK, drvdata->base + ECC_BLK_STARTACC_OFST);
- /* Setup accctrl to read & ecc override */
- writel(ECC_READ_EOVR, drvdata->base + ECC_BLK_ACCCTRL_OFST);
+ writel(0, drvdata->base + ECC_BLK_ADDRESS_OFST);
+ /* Setup accctrl to read & ecc & data override */
+ writel(ECC_READ_EDOVR, drvdata->base + ECC_BLK_ACCCTRL_OFST);
/* Kick it. */
writel(ECC_XACT_KICK, drvdata->base + ECC_BLK_STARTACC_OFST);
/* Setup write for single bit change */
- writel(0x1, drvdata->base + ECC_BLK_WDATA0_OFST);
- writel(0x0, drvdata->base + ECC_BLK_WDATA1_OFST);
- writel(0x0, drvdata->base + ECC_BLK_WDATA2_OFST);
- writel(0x0, drvdata->base + ECC_BLK_WDATA3_OFST);
+ writel(readl(drvdata->base + ECC_BLK_RDATA0_OFST) ^ 0x1,
+ drvdata->base + ECC_BLK_WDATA0_OFST);
+ writel(readl(drvdata->base + ECC_BLK_RDATA1_OFST),
+ drvdata->base + ECC_BLK_WDATA1_OFST);
+ writel(readl(drvdata->base + ECC_BLK_RDATA2_OFST),
+ drvdata->base + ECC_BLK_WDATA2_OFST);
+ writel(readl(drvdata->base + ECC_BLK_RDATA3_OFST),
+ drvdata->base + ECC_BLK_WDATA3_OFST);
+
/* Copy Read ECC to Write ECC */
writel(readl(drvdata->base + ECC_BLK_RECC0_OFST),
drvdata->base + ECC_BLK_WECC0_OFST);
diff --git a/drivers/edac/altera_edac.h b/drivers/edac/altera_edac.h
index 60513f201ffb..1532ec9c3510 100644
--- a/drivers/edac/altera_edac.h
+++ b/drivers/edac/altera_edac.h
@@ -321,7 +321,7 @@ struct altr_sdram_mc_data {
#define ECC_BLK_STARTACC_OFST 0x7C
#define ECC_XACT_KICK 0x10000
-#define ECC_WORD_WRITE 0xF
+#define ECC_WORD_WRITE 0xFF
#define ECC_WRITE_DOVR 0x101
#define ECC_WRITE_EDOVR 0x103
#define ECC_READ_EOVR 0x2
--
2.7.4
From: Thor Thayer <[email protected]>
The FIFO memory and ECC initialization doesn't need to be
done as a separate operation early in the startup.
Improve the Arria10 and Stratix10 peripheral FIFO init
by initializing memory and enabling ECC as part of the
device driver initialization.
Signed-off-by: Thor Thayer <[email protected]>
---
drivers/edac/altera_edac.c | 162 +++++++++++++++++++++++++--------------------
1 file changed, 91 insertions(+), 71 deletions(-)
diff --git a/drivers/edac/altera_edac.c b/drivers/edac/altera_edac.c
index acb3006df631..761199175c76 100644
--- a/drivers/edac/altera_edac.c
+++ b/drivers/edac/altera_edac.c
@@ -1361,8 +1361,19 @@ static const struct edac_device_prv_data a10_l2ecc_data = {
#ifdef CONFIG_EDAC_ALTERA_ETHERNET
+static int __init socfpga_init_ethernet_ecc(struct altr_edac_device_dev *dev)
+{
+ int ret;
+
+ ret = altr_init_a10_ecc_device_type("altr,socfpga-eth-mac-ecc");
+ if (ret)
+ return ret;
+
+ return altr_check_ecc_deps(dev);
+}
+
static const struct edac_device_prv_data a10_enetecc_data = {
- .setup = altr_check_ecc_deps,
+ .setup = socfpga_init_ethernet_ecc,
.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,
@@ -1374,21 +1385,25 @@ static const struct edac_device_prv_data a10_enetecc_data = {
.inject_fops = &altr_edac_a10_device_inject2_fops,
};
-static int __init socfpga_init_ethernet_ecc(void)
-{
- return altr_init_a10_ecc_device_type("altr,socfpga-eth-mac-ecc");
-}
-
-early_initcall(socfpga_init_ethernet_ecc);
-
#endif /* CONFIG_EDAC_ALTERA_ETHERNET */
/********************** NAND Device Functions **********************/
#ifdef CONFIG_EDAC_ALTERA_NAND
+static int __init socfpga_init_nand_ecc(struct altr_edac_device_dev *device)
+{
+ int ret;
+
+ ret = altr_init_a10_ecc_device_type("altr,socfpga-nand-ecc");
+ if (ret)
+ return ret;
+
+ return altr_check_ecc_deps(device);
+}
+
static const struct edac_device_prv_data a10_nandecc_data = {
- .setup = altr_check_ecc_deps,
+ .setup = socfpga_init_nand_ecc,
.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,
@@ -1400,21 +1415,25 @@ static const struct edac_device_prv_data a10_nandecc_data = {
.inject_fops = &altr_edac_a10_device_inject_fops,
};
-static int __init socfpga_init_nand_ecc(void)
-{
- return altr_init_a10_ecc_device_type("altr,socfpga-nand-ecc");
-}
-
-early_initcall(socfpga_init_nand_ecc);
-
#endif /* CONFIG_EDAC_ALTERA_NAND */
/********************** DMA Device Functions **********************/
#ifdef CONFIG_EDAC_ALTERA_DMA
+static int __init socfpga_init_dma_ecc(struct altr_edac_device_dev *device)
+{
+ int ret;
+
+ ret = altr_init_a10_ecc_device_type("altr,socfpga-dma-ecc");
+ if (ret)
+ return ret;
+
+ return altr_check_ecc_deps(device);
+}
+
static const struct edac_device_prv_data a10_dmaecc_data = {
- .setup = altr_check_ecc_deps,
+ .setup = socfpga_init_dma_ecc,
.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,
@@ -1426,21 +1445,25 @@ static const struct edac_device_prv_data a10_dmaecc_data = {
.inject_fops = &altr_edac_a10_device_inject_fops,
};
-static int __init socfpga_init_dma_ecc(void)
-{
- return altr_init_a10_ecc_device_type("altr,socfpga-dma-ecc");
-}
-
-early_initcall(socfpga_init_dma_ecc);
-
#endif /* CONFIG_EDAC_ALTERA_DMA */
/********************** USB Device Functions **********************/
#ifdef CONFIG_EDAC_ALTERA_USB
+static int __init socfpga_init_usb_ecc(struct altr_edac_device_dev *device)
+{
+ int ret;
+
+ ret = altr_init_a10_ecc_device_type("altr,socfpga-usb-ecc");
+ if (ret)
+ return ret;
+
+ return altr_check_ecc_deps(device);
+}
+
static const struct edac_device_prv_data a10_usbecc_data = {
- .setup = altr_check_ecc_deps,
+ .setup = socfpga_init_usb_ecc,
.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,
@@ -1452,21 +1475,25 @@ static const struct edac_device_prv_data a10_usbecc_data = {
.inject_fops = &altr_edac_a10_device_inject2_fops,
};
-static int __init socfpga_init_usb_ecc(void)
-{
- return altr_init_a10_ecc_device_type("altr,socfpga-usb-ecc");
-}
-
-early_initcall(socfpga_init_usb_ecc);
-
#endif /* CONFIG_EDAC_ALTERA_USB */
/********************** QSPI Device Functions **********************/
#ifdef CONFIG_EDAC_ALTERA_QSPI
+static int __init socfpga_init_qspi_ecc(struct altr_edac_device_dev *device)
+{
+ int ret;
+
+ ret = altr_init_a10_ecc_device_type("altr,socfpga-qspi-ecc");
+ if (ret)
+ return ret;
+
+ return altr_check_ecc_deps(device);
+}
+
static const struct edac_device_prv_data a10_qspiecc_data = {
- .setup = altr_check_ecc_deps,
+ .setup = socfpga_init_qspi_ecc,
.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,
@@ -1478,13 +1505,6 @@ static const struct edac_device_prv_data a10_qspiecc_data = {
.inject_fops = &altr_edac_a10_device_inject_fops,
};
-static int __init socfpga_init_qspi_ecc(void)
-{
- return altr_init_a10_ecc_device_type("altr,socfpga-qspi-ecc");
-}
-
-early_initcall(socfpga_init_qspi_ecc);
-
#endif /* CONFIG_EDAC_ALTERA_QSPI */
/********************* SDMMC Device Functions **********************/
@@ -1593,6 +1613,35 @@ static int altr_portb_setup(struct altr_edac_device_dev *device)
return rc;
}
+static int __init socfpga_init_sdmmc_ecc(struct altr_edac_device_dev *device)
+{
+ int rc = -ENODEV;
+ struct device_node *child;
+
+ child = of_find_compatible_node(NULL, NULL, "altr,socfpga-sdmmc-ecc");
+ if (!child)
+ return -ENODEV;
+
+ if (!of_device_is_available(child))
+ goto exit;
+
+ if (validate_parent_available(child))
+ goto exit;
+
+ /* Init portB */
+ rc = altr_init_a10_ecc_block(child, ALTR_A10_SDMMC_IRQ_MASK,
+ a10_sdmmceccb_data.ecc_enable_mask, 1);
+ if (rc)
+ goto exit;
+
+ /* Setup portB */
+ return altr_portb_setup(device);
+
+exit:
+ of_node_put(child);
+ return rc;
+}
+
static irqreturn_t altr_edac_a10_ecc_irq_portb(int irq, void *dev_id)
{
struct altr_edac_device_dev *ad = dev_id;
@@ -1617,7 +1666,7 @@ static irqreturn_t altr_edac_a10_ecc_irq_portb(int irq, void *dev_id)
}
static const struct edac_device_prv_data a10_sdmmcecca_data = {
- .setup = altr_portb_setup,
+ .setup = socfpga_init_sdmmc_ecc,
.ce_clear_mask = ALTR_A10_ECC_SERRPENA,
.ue_clear_mask = ALTR_A10_ECC_DERRPENA,
.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,
@@ -1630,7 +1679,7 @@ static const struct edac_device_prv_data a10_sdmmcecca_data = {
};
static const struct edac_device_prv_data a10_sdmmceccb_data = {
- .setup = altr_portb_setup,
+ .setup = socfpga_init_sdmmc_ecc,
.ce_clear_mask = ALTR_A10_ECC_SERRPENB,
.ue_clear_mask = ALTR_A10_ECC_DERRPENB,
.ecc_enable_mask = ALTR_A10_COMMON_ECC_EN_CTL,
@@ -1642,35 +1691,6 @@ static const struct edac_device_prv_data a10_sdmmceccb_data = {
.inject_fops = &altr_edac_a10_device_inject_fops,
};
-static int __init socfpga_init_sdmmc_ecc(void)
-{
- int rc = -ENODEV;
- struct device_node *child;
-
- if (!socfpga_is_a10() && !socfpga_is_s10())
- return -ENODEV;
-
- child = of_find_compatible_node(NULL, NULL, "altr,socfpga-sdmmc-ecc");
- if (!child) {
- edac_printk(KERN_WARNING, EDAC_DEVICE, "SDMMC node not found\n");
- return -ENODEV;
- }
-
- if (!of_device_is_available(child))
- goto exit;
-
- if (validate_parent_available(child))
- goto exit;
-
- rc = altr_init_a10_ecc_block(child, ALTR_A10_SDMMC_IRQ_MASK,
- a10_sdmmcecca_data.ecc_enable_mask, 1);
-exit:
- of_node_put(child);
- return rc;
-}
-
-early_initcall(socfpga_init_sdmmc_ecc);
-
#endif /* CONFIG_EDAC_ALTERA_SDMMC */
/********************* Arria10 EDAC Device Functions *************************/
--
2.7.4
On Tue, Mar 26, 2019 at 04:29:31PM -0500, [email protected] wrote:
> From: Thor Thayer <[email protected]>
>
> The FIFO memory and ECC initialization doesn't need to be
> done as a separate operation early in the startup.
>
> Improve the Arria10 and Stratix10 peripheral FIFO init
> by initializing memory and enabling ECC as part of the
> device driver initialization.
>
> Signed-off-by: Thor Thayer <[email protected]>
> ---
> drivers/edac/altera_edac.c | 162 +++++++++++++++++++++++++--------------------
> 1 file changed, 91 insertions(+), 71 deletions(-)
Both applied,
thanks.
--
Regards/Gruss,
Boris.
Good mailing practices for 400: avoid top-posting and trim the reply.