2019-06-07 13:30:41

by Bitan Biswas

Subject: [PATCH V1 1/6] i2c: tegra: clean up macros

Clean up macros by:
1) removing unused macros
2) replace constants by macro BIT()

Signed-off-by: Bitan Biswas <[email protected]>
---
drivers/i2c/busses/i2c-tegra.c | 17 +++--------------
1 file changed, 3 insertions(+), 14 deletions(-)

diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c
index 1dbba39..00692d8 100644
--- a/drivers/i2c/busses/i2c-tegra.c
+++ b/drivers/i2c/busses/i2c-tegra.c
@@ -54,20 +54,15 @@
#define I2C_INT_STATUS 0x068
#define I2C_INT_BUS_CLR_DONE BIT(11)
#define I2C_INT_PACKET_XFER_COMPLETE BIT(7)
-#define I2C_INT_ALL_PACKETS_XFER_COMPLETE BIT(6)
-#define I2C_INT_TX_FIFO_OVERFLOW BIT(5)
-#define I2C_INT_RX_FIFO_UNDERFLOW BIT(4)
#define I2C_INT_NO_ACK BIT(3)
#define I2C_INT_ARBITRATION_LOST BIT(2)
#define I2C_INT_TX_FIFO_DATA_REQ BIT(1)
#define I2C_INT_RX_FIFO_DATA_REQ BIT(0)
#define I2C_CLK_DIVISOR 0x06c
#define I2C_CLK_DIVISOR_STD_FAST_MODE_SHIFT 16
-#define I2C_CLK_MULTIPLIER_STD_FAST_MODE 8

#define DVC_CTRL_REG1 0x000
#define DVC_CTRL_REG1_INTR_EN BIT(10)
-#define DVC_CTRL_REG2 0x004
#define DVC_CTRL_REG3 0x008
#define DVC_CTRL_REG3_SW_PROG BIT(26)
#define DVC_CTRL_REG3_I2C_DONE_INTR_EN BIT(30)
@@ -75,24 +70,21 @@
#define DVC_STATUS_I2C_DONE_INTR BIT(30)

#define I2C_ERR_NONE 0x00
-#define I2C_ERR_NO_ACK 0x01
-#define I2C_ERR_ARBITRATION_LOST 0x02
-#define I2C_ERR_UNKNOWN_INTERRUPT 0x04
+#define I2C_ERR_NO_ACK BIT(0)
+#define I2C_ERR_ARBITRATION_LOST BIT(1)
+#define I2C_ERR_UNKNOWN_INTERRUPT BIT(2)

#define PACKET_HEADER0_HEADER_SIZE_SHIFT 28
#define PACKET_HEADER0_PACKET_ID_SHIFT 16
#define PACKET_HEADER0_CONT_ID_SHIFT 12
#define PACKET_HEADER0_PROTOCOL_I2C BIT(4)

-#define I2C_HEADER_HIGHSPEED_MODE BIT(22)
#define I2C_HEADER_CONT_ON_NAK BIT(21)
-#define I2C_HEADER_SEND_START_BYTE BIT(20)
#define I2C_HEADER_READ BIT(19)
#define I2C_HEADER_10BIT_ADDR BIT(18)
#define I2C_HEADER_IE_ENABLE BIT(17)
#define I2C_HEADER_REPEAT_START BIT(16)
#define I2C_HEADER_CONTINUE_XFER BIT(15)
-#define I2C_HEADER_MASTER_ADDR_SHIFT 12
#define I2C_HEADER_SLAVE_ADDR_SHIFT 1

#define I2C_BUS_CLEAR_CNFG 0x084
@@ -106,8 +98,6 @@

#define I2C_CONFIG_LOAD 0x08C
#define I2C_MSTR_CONFIG_LOAD BIT(0)
-#define I2C_SLV_CONFIG_LOAD BIT(1)
-#define I2C_TIMEOUT_CONFIG_LOAD BIT(2)

#define I2C_CLKEN_OVERRIDE 0x090
#define I2C_MST_CORE_CLKEN_OVR BIT(0)
@@ -133,7 +123,6 @@
#define I2C_STANDARD_MODE 100000
#define I2C_FAST_MODE 400000
#define I2C_FAST_PLUS_MODE 1000000
-#define I2C_HS_MODE 3500000

/* Packet header size in bytes */
#define I2C_PACKET_HEADER_SIZE 12
--
2.7.4

2019-06-07 13:30:41

by Bitan Biswas

Subject: [PATCH V1 2/6] i2c: tegra: remove unnecessary variable init

Remove variable initializations in functions that
are followed by assignments before use

Signed-off-by: Bitan Biswas <[email protected]>
---
drivers/i2c/busses/i2c-tegra.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c
index 00692d8..f7116b7 100644
--- a/drivers/i2c/busses/i2c-tegra.c
+++ b/drivers/i2c/busses/i2c-tegra.c
@@ -689,7 +689,7 @@ static int tegra_i2c_init(struct tegra_i2c_dev *i2c_dev, bool clk_reinit)
u32 val;
int err;
u32 clk_divisor, clk_multiplier;
- u32 tsu_thd = 0;
+ u32 tsu_thd;
u8 tlow, thigh;

err = pm_runtime_get_sync(i2c_dev->dev);
@@ -1218,7 +1218,7 @@ static int tegra_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
{
struct tegra_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
int i;
- int ret = 0;
+ int ret;

ret = pm_runtime_get_sync(i2c_dev->dev);
if (ret < 0) {
@@ -1489,7 +1489,7 @@ static int tegra_i2c_probe(struct platform_device *pdev)
void __iomem *base;
phys_addr_t base_phys;
int irq;
- int ret = 0;
+ int ret;

res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base_phys = res->start;
--
2.7.4