Hello !
This is third version of patch set containing following patches
for Cadence ethernet controller driver.
1. 0001-net-macb-add-phylink-support.patch
Replace phylib API's with phylink API's.
2. 0002-net-macb-add-support-for-sgmii-MAC-PHY-interface.patch
This patch add support for SGMII mode.
3. 0004-net-macb-add-support-for-c45-PHY.patch
This patch is to support C45 PHY.
4. 0005-net-macb-add-support-for-high-speed-interface
This patch add support for 10G USXGMII PCS in fixed mode.
5. 0006-net-macb-parameter-added-to-cadence-ethernet-controller-DT-binding
New parameter added to Cadence ethernet controller DT binding
for USXGMII interface.
Changes in v2:
1. Dropped patch configuring TI PHY DP83867 from
Cadence PCI wrapper driver.
2. Removed code registering emulated PHY for fixed mode.
3. Code reformatting as per Andrew's and Florian's suggestions.
Changes in v3:
Based on Russell's suggestions
1. Configure MAC in mac_config only for non in-band modes
2. Handle dynamic phy_mode changes in mac_config
3. Move MAC configurations to mac_config
4. Removed seemingly redundant check for phylink handle
5. Removed code from mac_an_restart and mac_link_state
now just return -EOPNOTSUPP
Regards,
Parshuram Thombare
Parshuram Thombare (5):
net: macb: add phylink support
net: macb: add support for sgmii MAC-PHY interface
net: macb: add support for c45 PHY
net: macb: add support for high speed interface
net: macb: parameter added to cadence ethernet controller DT binding
.../devicetree/bindings/net/macb.txt | 3 +
drivers/net/ethernet/cadence/Kconfig | 2 +-
drivers/net/ethernet/cadence/macb.h | 113 +++-
drivers/net/ethernet/cadence/macb_main.c | 619 +++++++++++++-----
4 files changed, 554 insertions(+), 183 deletions(-)
--
2.17.1
This patch replace phylib API's by phylink API's.
Signed-off-by: Parshuram Thombare <[email protected]>
---
drivers/net/ethernet/cadence/Kconfig | 2 +-
drivers/net/ethernet/cadence/macb.h | 3 +
drivers/net/ethernet/cadence/macb_main.c | 304 ++++++++++++-----------
3 files changed, 166 insertions(+), 143 deletions(-)
diff --git a/drivers/net/ethernet/cadence/Kconfig b/drivers/net/ethernet/cadence/Kconfig
index 1766697c9c5a..d71411a71587 100644
--- a/drivers/net/ethernet/cadence/Kconfig
+++ b/drivers/net/ethernet/cadence/Kconfig
@@ -22,7 +22,7 @@ if NET_VENDOR_CADENCE
config MACB
tristate "Cadence MACB/GEM support"
depends on HAS_DMA
- select PHYLIB
+ select PHYLINK
---help---
The Cadence MACB ethernet interface is found on many Atmel AT32 and
AT91 parts. This driver also supports the Cadence GEM (Gigabit
diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index 00ee5e8e0ff0..35ed13236c8b 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -14,6 +14,7 @@
#include <linux/ptp_clock_kernel.h>
#include <linux/net_tstamp.h>
#include <linux/interrupt.h>
+#include <linux/phylink.h>
#if defined(CONFIG_ARCH_DMA_ADDR_T_64BIT) || defined(CONFIG_MACB_USE_HWSTAMP)
#define MACB_EXT_DESC
@@ -1227,6 +1228,8 @@ struct macb {
u32 rx_intr_mask;
struct macb_pm_data pm_data;
+ struct phylink *pl;
+ struct phylink_config pl_config;
};
#ifdef CONFIG_MACB_USE_HWSTAMP
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index c545c5b435d8..97d168dfa873 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -39,6 +39,7 @@
#include <linux/tcp.h>
#include <linux/iopoll.h>
#include <linux/pm_runtime.h>
+#include <linux/phylink.h>
#include "macb.h"
/* This structure is only used for MACB on SiFive FU540 devices */
@@ -438,115 +439,145 @@ static void macb_set_tx_clk(struct clk *clk, int speed, struct net_device *dev)
netdev_err(dev, "adjusting tx_clk failed.\n");
}
-static void macb_handle_link_change(struct net_device *dev)
+static void gem_phylink_validate(struct phylink_config *pl_config,
+ unsigned long *supported,
+ struct phylink_link_state *state)
{
- struct macb *bp = netdev_priv(dev);
- struct phy_device *phydev = dev->phydev;
- unsigned long flags;
- int status_change = 0;
+ struct net_device *netdev = to_net_dev(pl_config->dev);
+ struct macb *bp = netdev_priv(netdev);
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+ switch (state->interface) {
+ case PHY_INTERFACE_MODE_GMII:
+ case PHY_INTERFACE_MODE_RGMII:
+ if (bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE) {
+ phylink_set(mask, 1000baseT_Full);
+ phylink_set(mask, 1000baseX_Full);
+ if (!(bp->caps & MACB_CAPS_NO_GIGABIT_HALF)) {
+ phylink_set(mask, 1000baseT_Half);
+ phylink_set(mask, 1000baseT_Half);
+ }
+ }
+ /* fallthrough */
+ case PHY_INTERFACE_MODE_MII:
+ case PHY_INTERFACE_MODE_RMII:
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+ break;
+ default:
+ break;
+ }
- spin_lock_irqsave(&bp->lock, flags);
+ linkmode_and(supported, supported, mask);
+ linkmode_and(state->advertising, state->advertising, mask);
- if (phydev->link) {
- if ((bp->speed != phydev->speed) ||
- (bp->duplex != phydev->duplex)) {
- u32 reg;
+}
- reg = macb_readl(bp, NCFGR);
- reg &= ~(MACB_BIT(SPD) | MACB_BIT(FD));
- if (macb_is_gem(bp))
- reg &= ~GEM_BIT(GBE);
+static int gem_phylink_mac_link_state(struct phylink_config *pl_config,
+ struct phylink_link_state *state)
+{
+ return -EOPNOTSUPP;
+}
- if (phydev->duplex)
- reg |= MACB_BIT(FD);
- if (phydev->speed == SPEED_100)
- reg |= MACB_BIT(SPD);
- if (phydev->speed == SPEED_1000 &&
- bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE)
- reg |= GEM_BIT(GBE);
+static void gem_mac_config(struct phylink_config *pl_config, unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct net_device *netdev = to_net_dev(pl_config->dev);
+ struct macb *bp = netdev_priv(netdev);
+ unsigned long flags;
- macb_or_gem_writel(bp, NCFGR, reg);
+ spin_lock_irqsave(&bp->lock, flags);
- bp->speed = phydev->speed;
- bp->duplex = phydev->duplex;
- status_change = 1;
- }
- }
+ if (!phylink_autoneg_inband(mode) &&
+ (bp->speed != state->speed ||
+ bp->duplex != state->duplex)) {
+ u32 reg;
- if (phydev->link != bp->link) {
- if (!phydev->link) {
- bp->speed = 0;
- bp->duplex = -1;
+ reg = macb_readl(bp, NCFGR);
+ reg &= ~(MACB_BIT(SPD) | MACB_BIT(FD));
+ if (macb_is_gem(bp))
+ reg &= ~GEM_BIT(GBE);
+ if (state->duplex)
+ reg |= MACB_BIT(FD);
+
+ switch (state->speed) {
+ case SPEED_1000:
+ reg |= GEM_BIT(GBE);
+ break;
+ case SPEED_100:
+ reg |= MACB_BIT(SPD);
+ break;
+ default:
+ break;
}
- bp->link = phydev->link;
+ macb_or_gem_writel(bp, NCFGR, reg);
+
+ bp->speed = state->speed;
+ bp->duplex = state->duplex;
- status_change = 1;
+ if (state->link)
+ macb_set_tx_clk(bp->tx_clk, state->speed, netdev);
}
spin_unlock_irqrestore(&bp->lock, flags);
+}
- if (status_change) {
- if (phydev->link) {
- /* Update the TX clock rate if and only if the link is
- * up and there has been a link change.
- */
- macb_set_tx_clk(bp->tx_clk, phydev->speed, dev);
+static void gem_mac_link_up(struct phylink_config *pl_config, unsigned int mode,
+ phy_interface_t interface, struct phy_device *phy)
+{
+ struct net_device *netdev = to_net_dev(pl_config->dev);
+ struct macb *bp = netdev_priv(netdev);
- netif_carrier_on(dev);
- netdev_info(dev, "link up (%d/%s)\n",
- phydev->speed,
- phydev->duplex == DUPLEX_FULL ?
- "Full" : "Half");
- } else {
- netif_carrier_off(dev);
- netdev_info(dev, "link down\n");
- }
- }
+ bp->link = 1;
+ /* Enable TX and RX */
+ macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(RE) | MACB_BIT(TE));
+}
+
+static void gem_mac_link_down(struct phylink_config *pl_config,
+ unsigned int mode, phy_interface_t interface)
+{
+ struct net_device *netdev = to_net_dev(pl_config->dev);
+ struct macb *bp = netdev_priv(netdev);
+
+ bp->link = 0;
+ /* Disable TX and RX */
+ macb_writel(bp, NCR,
+ macb_readl(bp, NCR) & ~(MACB_BIT(RE) | MACB_BIT(TE)));
}
+static const struct phylink_mac_ops gem_phylink_ops = {
+ .validate = gem_phylink_validate,
+ .mac_link_state = gem_phylink_mac_link_state,
+ .mac_config = gem_mac_config,
+ .mac_link_up = gem_mac_link_up,
+ .mac_link_down = gem_mac_link_down,
+};
+
/* based on au1000_eth. c*/
static int macb_mii_probe(struct net_device *dev)
{
struct macb *bp = netdev_priv(dev);
struct phy_device *phydev;
struct device_node *np;
- int ret, i;
+ int ret;
np = bp->pdev->dev.of_node;
ret = 0;
- if (np) {
- if (of_phy_is_fixed_link(np)) {
- bp->phy_node = of_node_get(np);
- } else {
- bp->phy_node = of_parse_phandle(np, "phy-handle", 0);
- /* fallback to standard phy registration if no
- * phy-handle was found nor any phy found during
- * dt phy registration
- */
- if (!bp->phy_node && !phy_find_first(bp->mii_bus)) {
- for (i = 0; i < PHY_MAX_ADDR; i++) {
- phydev = mdiobus_scan(bp->mii_bus, i);
- if (IS_ERR(phydev) &&
- PTR_ERR(phydev) != -ENODEV) {
- ret = PTR_ERR(phydev);
- break;
- }
- }
-
- if (ret)
- return -ENODEV;
- }
- }
+ bp->pl_config.dev = &dev->dev;
+ bp->pl_config.type = PHYLINK_NETDEV;
+ bp->pl = phylink_create(&bp->pl_config, of_fwnode_handle(np),
+ bp->phy_interface, &gem_phylink_ops);
+ if (IS_ERR(bp->pl)) {
+ netdev_err(dev,
+ "error creating PHYLINK: %ld\n", PTR_ERR(bp->pl));
+ return PTR_ERR(bp->pl);
}
- if (bp->phy_node) {
- phydev = of_phy_connect(dev, bp->phy_node,
- &macb_handle_link_change, 0,
- bp->phy_interface);
- if (!phydev)
- return -ENODEV;
- } else {
+ ret = phylink_of_phy_connect(bp->pl, np, 0);
+ if (ret == -ENODEV && bp->mii_bus) {
phydev = phy_find_first(bp->mii_bus);
if (!phydev) {
netdev_err(dev, "no PHY found\n");
@@ -554,29 +585,18 @@ static int macb_mii_probe(struct net_device *dev)
}
/* attach the mac to the phy */
- ret = phy_connect_direct(dev, phydev, &macb_handle_link_change,
- bp->phy_interface);
+ ret = phylink_connect_phy(bp->pl, phydev);
if (ret) {
netdev_err(dev, "Could not attach to PHY\n");
return ret;
}
}
- /* mask with MAC supported features */
- if (macb_is_gem(bp) && bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE)
- phy_set_max_speed(phydev, SPEED_1000);
- else
- phy_set_max_speed(phydev, SPEED_100);
-
- if (bp->caps & MACB_CAPS_NO_GIGABIT_HALF)
- phy_remove_link_mode(phydev,
- ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
-
bp->link = 0;
bp->speed = 0;
bp->duplex = -1;
- return 0;
+ return ret;
}
static int macb_mii_init(struct macb *bp)
@@ -604,17 +624,7 @@ static int macb_mii_init(struct macb *bp)
dev_set_drvdata(&bp->dev->dev, bp->mii_bus);
np = bp->pdev->dev.of_node;
- if (np && of_phy_is_fixed_link(np)) {
- if (of_phy_register_fixed_link(np) < 0) {
- dev_err(&bp->pdev->dev,
- "broken fixed-link specification %pOF\n", np);
- goto err_out_free_mdiobus;
- }
-
- err = mdiobus_register(bp->mii_bus);
- } else {
- err = of_mdiobus_register(bp->mii_bus, np);
- }
+ err = of_mdiobus_register(bp->mii_bus, np);
if (err)
goto err_out_free_fixed_link;
@@ -630,7 +640,6 @@ static int macb_mii_init(struct macb *bp)
err_out_free_fixed_link:
if (np && of_phy_is_fixed_link(np))
of_phy_deregister_fixed_link(np);
-err_out_free_mdiobus:
of_node_put(bp->phy_node);
mdiobus_free(bp->mii_bus);
err_out:
@@ -2421,12 +2430,6 @@ static int macb_open(struct net_device *dev)
/* carrier starts down */
netif_carrier_off(dev);
- /* if the phy is not yet register, retry later*/
- if (!dev->phydev) {
- err = -EAGAIN;
- goto pm_exit;
- }
-
/* RX buffers initialization */
macb_init_rx_buffer_size(bp, bufsz);
@@ -2444,7 +2447,7 @@ static int macb_open(struct net_device *dev)
macb_init_hw(bp);
/* schedule a link state check */
- phy_start(dev->phydev);
+ phylink_start(bp->pl);
netif_tx_start_all_queues(dev);
@@ -2471,8 +2474,7 @@ static int macb_close(struct net_device *dev)
for (q = 0, queue = bp->queues; q < bp->num_queues; ++q, ++queue)
napi_disable(&queue->napi);
- if (dev->phydev)
- phy_stop(dev->phydev);
+ phylink_stop(bp->pl);
spin_lock_irqsave(&bp->lock, flags);
macb_reset_hw(bp);
@@ -3161,6 +3163,23 @@ static int gem_set_rxnfc(struct net_device *netdev, struct ethtool_rxnfc *cmd)
return ret;
}
+static int gem_ethtool_get_link_ksettings(struct net_device *netdev,
+ struct ethtool_link_ksettings *cmd)
+{
+ struct macb *bp = netdev_priv(netdev);
+
+ return phylink_ethtool_ksettings_get(bp->pl, cmd);
+}
+
+static int
+gem_ethtool_set_link_ksettings(struct net_device *netdev,
+ const struct ethtool_link_ksettings *cmd)
+{
+ struct macb *bp = netdev_priv(netdev);
+
+ return phylink_ethtool_ksettings_set(bp->pl, cmd);
+}
+
static const struct ethtool_ops macb_ethtool_ops = {
.get_regs_len = macb_get_regs_len,
.get_regs = macb_get_regs,
@@ -3168,8 +3187,8 @@ static const struct ethtool_ops macb_ethtool_ops = {
.get_ts_info = ethtool_op_get_ts_info,
.get_wol = macb_get_wol,
.set_wol = macb_set_wol,
- .get_link_ksettings = phy_ethtool_get_link_ksettings,
- .set_link_ksettings = phy_ethtool_set_link_ksettings,
+ .get_link_ksettings = gem_ethtool_get_link_ksettings,
+ .set_link_ksettings = gem_ethtool_set_link_ksettings,
.get_ringparam = macb_get_ringparam,
.set_ringparam = macb_set_ringparam,
};
@@ -3182,8 +3201,8 @@ static const struct ethtool_ops gem_ethtool_ops = {
.get_ethtool_stats = gem_get_ethtool_stats,
.get_strings = gem_get_ethtool_strings,
.get_sset_count = gem_get_sset_count,
- .get_link_ksettings = phy_ethtool_get_link_ksettings,
- .set_link_ksettings = phy_ethtool_set_link_ksettings,
+ .get_link_ksettings = gem_ethtool_get_link_ksettings,
+ .set_link_ksettings = gem_ethtool_set_link_ksettings,
.get_ringparam = macb_get_ringparam,
.set_ringparam = macb_set_ringparam,
.get_rxnfc = gem_get_rxnfc,
@@ -3192,17 +3211,13 @@ static const struct ethtool_ops gem_ethtool_ops = {
static int macb_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
{
- struct phy_device *phydev = dev->phydev;
struct macb *bp = netdev_priv(dev);
if (!netif_running(dev))
return -EINVAL;
- if (!phydev)
- return -ENODEV;
-
if (!bp->ptp_info)
- return phy_mii_ioctl(phydev, rq, cmd);
+ return phylink_mii_ioctl(bp->pl, rq, cmd);
switch (cmd) {
case SIOCSHWTSTAMP:
@@ -3210,7 +3225,7 @@ static int macb_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
case SIOCGHWTSTAMP:
return bp->ptp_info->get_hwtst(dev, rq);
default:
- return phy_mii_ioctl(phydev, rq, cmd);
+ return phylink_mii_ioctl(bp->pl, rq, cmd);
}
}
@@ -3710,7 +3725,7 @@ static int at91ether_open(struct net_device *dev)
MACB_BIT(HRESP));
/* schedule a link state check */
- phy_start(dev->phydev);
+ phylink_start(lp->pl);
netif_start_queue(dev);
@@ -4183,13 +4198,12 @@ static int macb_probe(struct platform_device *pdev)
struct clk *tsu_clk = NULL;
unsigned int queue_mask, num_queues;
bool native_io;
- struct phy_device *phydev;
struct net_device *dev;
struct resource *regs;
void __iomem *mem;
const char *mac;
struct macb *bp;
- int err, val;
+ int err, val, phy_mode;
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
mem = devm_ioremap_resource(&pdev->dev, regs);
@@ -4310,12 +4324,12 @@ static int macb_probe(struct platform_device *pdev)
macb_get_hwaddr(bp);
}
- err = of_get_phy_mode(np);
- if (err < 0)
+ phy_mode = of_get_phy_mode(np);
+ if (phy_mode < 0)
/* not found in DT, MII by default */
bp->phy_interface = PHY_INTERFACE_MODE_MII;
else
- bp->phy_interface = err;
+ bp->phy_interface = phy_mode;
/* IP specific init */
err = init(pdev);
@@ -4326,8 +4340,6 @@ static int macb_probe(struct platform_device *pdev)
if (err)
goto err_out_free_netdev;
- phydev = dev->phydev;
-
netif_carrier_off(dev);
err = register_netdev(dev);
@@ -4339,8 +4351,6 @@ static int macb_probe(struct platform_device *pdev)
tasklet_init(&bp->hresp_err_tasklet, macb_hresp_error_task,
(unsigned long)bp);
- phy_attached_info(phydev);
-
netdev_info(dev, "Cadence %s rev 0x%08x at 0x%08lx irq %d (%pM)\n",
macb_is_gem(bp) ? "GEM" : "MACB", macb_readl(bp, MID),
dev->base_addr, dev->irq, dev->dev_addr);
@@ -4351,7 +4361,9 @@ static int macb_probe(struct platform_device *pdev)
return 0;
err_out_unregister_mdio:
- phy_disconnect(dev->phydev);
+ rtnl_lock();
+ phylink_disconnect_phy(bp->pl);
+ rtnl_unlock();
mdiobus_unregister(bp->mii_bus);
of_node_put(bp->phy_node);
if (np && of_phy_is_fixed_link(np))
@@ -4385,13 +4397,18 @@ static int macb_remove(struct platform_device *pdev)
if (dev) {
bp = netdev_priv(dev);
- if (dev->phydev)
- phy_disconnect(dev->phydev);
+ if (bp->pl) {
+ rtnl_lock();
+ phylink_disconnect_phy(bp->pl);
+ rtnl_unlock();
+ }
mdiobus_unregister(bp->mii_bus);
if (np && of_phy_is_fixed_link(np))
of_phy_deregister_fixed_link(np);
dev->phydev = NULL;
mdiobus_free(bp->mii_bus);
+ if (bp->pl)
+ phylink_destroy(bp->pl);
unregister_netdev(dev);
pm_runtime_disable(&pdev->dev);
@@ -4434,8 +4451,9 @@ static int __maybe_unused macb_suspend(struct device *dev)
for (q = 0, queue = bp->queues; q < bp->num_queues;
++q, ++queue)
napi_disable(&queue->napi);
- phy_stop(netdev->phydev);
- phy_suspend(netdev->phydev);
+ phylink_stop(bp->pl);
+ if (netdev->phydev)
+ phy_suspend(netdev->phydev);
spin_lock_irqsave(&bp->lock, flags);
macb_reset_hw(bp);
spin_unlock_irqrestore(&bp->lock, flags);
@@ -4483,9 +4501,11 @@ static int __maybe_unused macb_resume(struct device *dev)
for (q = 0, queue = bp->queues; q < bp->num_queues;
++q, ++queue)
napi_enable(&queue->napi);
- phy_resume(netdev->phydev);
- phy_init_hw(netdev->phydev);
- phy_start(netdev->phydev);
+ if (netdev->phydev) {
+ phy_resume(netdev->phydev);
+ phy_init_hw(netdev->phydev);
+ }
+ phylink_start(bp->pl);
}
bp->macbgem_ops.mog_init_rings(bp);
--
2.17.1
This patch add support for SGMII interface) and
2.5Gbps MAC in Cadence ethernet controller driver.
Signed-off-by: Parshuram Thombare <[email protected]>
---
drivers/net/ethernet/cadence/macb.h | 54 +++++++++---
drivers/net/ethernet/cadence/macb_main.c | 108 +++++++++++++++++++++--
2 files changed, 140 insertions(+), 22 deletions(-)
diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index 35ed13236c8b..0647689f9796 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -80,6 +80,7 @@
#define MACB_RBQPH 0x04D4
/* GEM register offsets. */
+#define GEM_NCR 0x0000 /* Network Control */
#define GEM_NCFGR 0x0004 /* Network Config */
#define GEM_USRIO 0x000c /* User IO */
#define GEM_DMACFG 0x0010 /* DMA Configuration */
@@ -159,6 +160,7 @@
#define GEM_PEFTN 0x01f4 /* PTP Peer Event Frame Tx Ns */
#define GEM_PEFRSL 0x01f8 /* PTP Peer Event Frame Rx Sec Low */
#define GEM_PEFRN 0x01fc /* PTP Peer Event Frame Rx Ns */
+#define GEM_PCS_CTRL 0x0200 /* PCS Control */
#define GEM_DCFG1 0x0280 /* Design Config 1 */
#define GEM_DCFG2 0x0284 /* Design Config 2 */
#define GEM_DCFG3 0x0288 /* Design Config 3 */
@@ -274,6 +276,10 @@
#define MACB_IRXFCS_OFFSET 19
#define MACB_IRXFCS_SIZE 1
+/* GEM specific NCR bitfields. */
+#define GEM_TWO_PT_FIVE_GIG_OFFSET 29
+#define GEM_TWO_PT_FIVE_GIG_SIZE 1
+
/* GEM specific NCFGR bitfields. */
#define GEM_GBE_OFFSET 10 /* Gigabit mode enable */
#define GEM_GBE_SIZE 1
@@ -326,6 +332,9 @@
#define MACB_MDIO_SIZE 1
#define MACB_IDLE_OFFSET 2 /* The PHY management logic is idle */
#define MACB_IDLE_SIZE 1
+#define MACB_DUPLEX_OFFSET 3
+#define MACB_DUPLEX_SIZE 1
+
/* Bitfields in TSR */
#define MACB_UBR_OFFSET 0 /* Used bit read */
@@ -459,11 +468,17 @@
#define MACB_REV_OFFSET 0
#define MACB_REV_SIZE 16
+/* Bitfields in PCS_CONTROL. */
+#define GEM_PCS_CTRL_RST_OFFSET 15
+#define GEM_PCS_CTRL_RST_SIZE 1
+
/* Bitfields in DCFG1. */
#define GEM_IRQCOR_OFFSET 23
#define GEM_IRQCOR_SIZE 1
#define GEM_DBWDEF_OFFSET 25
#define GEM_DBWDEF_SIZE 3
+#define GEM_NO_PCS_OFFSET 0
+#define GEM_NO_PCS_SIZE 1
/* Bitfields in DCFG2. */
#define GEM_RX_PKT_BUFF_OFFSET 20
@@ -636,19 +651,32 @@
#define MACB_MAN_CODE 2
/* Capability mask bits */
-#define MACB_CAPS_ISR_CLEAR_ON_WRITE 0x00000001
-#define MACB_CAPS_USRIO_HAS_CLKEN 0x00000002
-#define MACB_CAPS_USRIO_DEFAULT_IS_MII_GMII 0x00000004
-#define MACB_CAPS_NO_GIGABIT_HALF 0x00000008
-#define MACB_CAPS_USRIO_DISABLED 0x00000010
-#define MACB_CAPS_JUMBO 0x00000020
-#define MACB_CAPS_GEM_HAS_PTP 0x00000040
-#define MACB_CAPS_BD_RD_PREFETCH 0x00000080
-#define MACB_CAPS_NEEDS_RSTONUBR 0x00000100
-#define MACB_CAPS_FIFO_MODE 0x10000000
-#define MACB_CAPS_GIGABIT_MODE_AVAILABLE 0x20000000
-#define MACB_CAPS_SG_DISABLED 0x40000000
-#define MACB_CAPS_MACB_IS_GEM 0x80000000
+#define MACB_CAPS_ISR_CLEAR_ON_WRITE BIT(0)
+#define MACB_CAPS_USRIO_HAS_CLKEN BIT(1)
+#define MACB_CAPS_USRIO_DEFAULT_IS_MII_GMII BIT(2)
+#define MACB_CAPS_NO_GIGABIT_HALF BIT(3)
+#define MACB_CAPS_USRIO_DISABLED BIT(4)
+#define MACB_CAPS_JUMBO BIT(5)
+#define MACB_CAPS_GEM_HAS_PTP BIT(6)
+#define MACB_CAPS_BD_RD_PREFETCH BIT(7)
+#define MACB_CAPS_NEEDS_RSTONUBR BIT(8)
+#define MACB_CAPS_FIFO_MODE BIT(28)
+#define MACB_CAPS_GIGABIT_MODE_AVAILABLE BIT(29)
+#define MACB_CAPS_SG_DISABLED BIT(30)
+#define MACB_CAPS_MACB_IS_GEM BIT(31)
+#define MACB_CAPS_PCS BIT(24)
+#define MACB_CAPS_MACB_IS_GEM_GXL BIT(25)
+
+#define MACB_GEM7010_IDNUM 0x009
+#define MACB_GEM7014_IDNU 0x107
+#define MACB_GEM7014A_IDNUM 0x207
+#define MACB_GEM7016_IDNUM 0x10a
+#define MACB_GEM7017_IDNUM 0x00a
+#define MACB_GEM7017A_IDNUM 0x20a
+#define MACB_GEM7020_IDNUM 0x003
+#define MACB_GEM7021_IDNUM 0x00c
+#define MACB_GEM7021A_IDNUM 0x20c
+#define MACB_GEM7022_IDNUM 0x00b
/* LSO settings */
#define MACB_LSO_UFO_ENABLE 0x01
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index 97d168dfa873..f1e58801ccf5 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -403,6 +403,7 @@ static int macb_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
*/
static void macb_set_tx_clk(struct clk *clk, int speed, struct net_device *dev)
{
+ struct macb *bp = netdev_priv(dev);
long ferr, rate, rate_rounded;
if (!clk)
@@ -418,6 +419,12 @@ static void macb_set_tx_clk(struct clk *clk, int speed, struct net_device *dev)
case SPEED_1000:
rate = 125000000;
break;
+ case SPEED_2500:
+ if (bp->caps & MACB_CAPS_MACB_IS_GEM_GXL)
+ rate = 312500000;
+ else
+ rate = 125000000;
+ break;
default:
return;
}
@@ -448,15 +455,19 @@ static void gem_phylink_validate(struct phylink_config *pl_config,
__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
switch (state->interface) {
+ case PHY_INTERFACE_MODE_SGMII:
+ if (bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE) {
+ phylink_set(mask, 2500baseT_Full);
+ phylink_set(mask, 2500baseX_Full);
+ }
+ /* fallthrough */
case PHY_INTERFACE_MODE_GMII:
case PHY_INTERFACE_MODE_RGMII:
if (bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE) {
phylink_set(mask, 1000baseT_Full);
phylink_set(mask, 1000baseX_Full);
- if (!(bp->caps & MACB_CAPS_NO_GIGABIT_HALF)) {
+ if (!(bp->caps & MACB_CAPS_NO_GIGABIT_HALF))
phylink_set(mask, 1000baseT_Half);
- phylink_set(mask, 1000baseT_Half);
- }
}
/* fallthrough */
case PHY_INTERFACE_MODE_MII:
@@ -466,13 +477,19 @@ static void gem_phylink_validate(struct phylink_config *pl_config,
phylink_set(mask, 100baseT_Half);
phylink_set(mask, 100baseT_Full);
break;
+ case PHY_INTERFACE_MODE_1000BASEX:
+ case PHY_INTERFACE_MODE_2500BASEX:
+ phylink_set(mask, 1000baseT_Full);
+ phylink_set(mask, 1000baseX_Full);
+ phylink_set(mask, 2500baseT_Full);
+ phylink_set(mask, 2500baseX_Full);
+ break;
default:
break;
}
linkmode_and(supported, supported, mask);
linkmode_and(state->advertising, state->advertising, mask);
-
}
static int gem_phylink_mac_link_state(struct phylink_config *pl_config,
@@ -486,23 +503,54 @@ static void gem_mac_config(struct phylink_config *pl_config, unsigned int mode,
{
struct net_device *netdev = to_net_dev(pl_config->dev);
struct macb *bp = netdev_priv(netdev);
+ bool change_interface = bp->phy_interface != state->interface;
unsigned long flags;
spin_lock_irqsave(&bp->lock, flags);
+ if (change_interface) {
+ if (bp->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ bp->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ bp->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
+ gem_writel(bp, NCFGR, ~GEM_BIT(SGMIIEN) &
+ ~GEM_BIT(PCSSEL) &
+ gem_readl(bp, NCFGR));
+ gem_writel(bp, NCR, ~GEM_BIT(TWO_PT_FIVE_GIG) &
+ gem_readl(bp, NCR));
+ gem_writel(bp, PCS_CTRL, gem_readl(bp, PCS_CTRL) |
+ GEM_BIT(PCS_CTRL_RST));
+ }
+ bp->phy_interface = state->interface;
+ }
+
if (!phylink_autoneg_inband(mode) &&
(bp->speed != state->speed ||
- bp->duplex != state->duplex)) {
+ bp->duplex != state->duplex ||
+ change_interface)) {
u32 reg;
reg = macb_readl(bp, NCFGR);
reg &= ~(MACB_BIT(SPD) | MACB_BIT(FD));
if (macb_is_gem(bp))
reg &= ~GEM_BIT(GBE);
+ macb_or_gem_writel(bp, NCFGR, reg);
+
+ if (bp->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ bp->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ bp->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
+ gem_writel(bp, NCFGR, GEM_BIT(SGMIIEN) |
+ GEM_BIT(PCSSEL) |
+ gem_readl(bp, NCFGR));
+
+ reg = macb_readl(bp, NCFGR);
if (state->duplex)
reg |= MACB_BIT(FD);
switch (state->speed) {
+ case SPEED_2500:
+ gem_writel(bp, NCR, GEM_BIT(TWO_PT_FIVE_GIG) |
+ gem_readl(bp, NCR));
+ break;
case SPEED_1000:
reg |= GEM_BIT(GBE);
break;
@@ -593,8 +641,8 @@ static int macb_mii_probe(struct net_device *dev)
}
bp->link = 0;
- bp->speed = 0;
- bp->duplex = -1;
+ bp->speed = SPEED_UNKNOWN;
+ bp->duplex = DUPLEX_UNKNOWN;
return ret;
}
@@ -3343,6 +3391,22 @@ static void macb_configure_caps(struct macb *bp,
dcfg = gem_readl(bp, DCFG1);
if (GEM_BFEXT(IRQCOR, dcfg) == 0)
bp->caps |= MACB_CAPS_ISR_CLEAR_ON_WRITE;
+ if (GEM_BFEXT(NO_PCS, dcfg) == 0)
+ bp->caps |= MACB_CAPS_PCS;
+ switch (MACB_BFEXT(IDNUM, macb_readl(bp, MID))) {
+ case MACB_GEM7016_IDNUM:
+ case MACB_GEM7017_IDNUM:
+ case MACB_GEM7017A_IDNUM:
+ case MACB_GEM7020_IDNUM:
+ case MACB_GEM7021_IDNUM:
+ case MACB_GEM7021A_IDNUM:
+ case MACB_GEM7022_IDNUM:
+ bp->caps |= MACB_CAPS_USRIO_DISABLED;
+ bp->caps |= MACB_CAPS_MACB_IS_GEM_GXL;
+ break;
+ default:
+ break;
+ }
dcfg = gem_readl(bp, DCFG2);
if ((dcfg & (GEM_BIT(RX_PKT_BUFF) | GEM_BIT(TX_PKT_BUFF))) == 0)
bp->caps |= MACB_CAPS_FIFO_MODE;
@@ -4325,11 +4389,37 @@ static int macb_probe(struct platform_device *pdev)
}
phy_mode = of_get_phy_mode(np);
- if (phy_mode < 0)
+ if (phy_mode < 0) {
/* not found in DT, MII by default */
bp->phy_interface = PHY_INTERFACE_MODE_MII;
- else
+ } else if (bp->caps & MACB_CAPS_MACB_IS_GEM_GXL) {
+ u32 interface_supported = 1;
+
+ if (phy_mode == PHY_INTERFACE_MODE_SGMII ||
+ phy_mode == PHY_INTERFACE_MODE_1000BASEX ||
+ phy_mode == PHY_INTERFACE_MODE_2500BASEX) {
+ if (!(bp->caps & MACB_CAPS_PCS))
+ interface_supported = 0;
+ } else if (phy_mode == PHY_INTERFACE_MODE_GMII ||
+ phy_mode == PHY_INTERFACE_MODE_RGMII) {
+ if (!macb_is_gem(bp))
+ interface_supported = 0;
+ } else if (phy_mode != PHY_INTERFACE_MODE_RMII &&
+ phy_mode != PHY_INTERFACE_MODE_MII) {
+ /* Add new mode before this */
+ interface_supported = 0;
+ }
+
+ if (!interface_supported) {
+ netdev_err(dev, "Phy mode %s not supported",
+ phy_modes(phy_mode));
+ goto err_out_free_netdev;
+ }
+
bp->phy_interface = phy_mode;
+ } else {
+ bp->phy_interface = phy_mode;
+ }
/* IP specific init */
err = init(pdev);
--
2.17.1
This patch modify MDIO read/write functions to support
communication with C45 PHY.
Signed-off-by: Parshuram Thombare <[email protected]>
---
drivers/net/ethernet/cadence/macb.h | 15 ++++--
drivers/net/ethernet/cadence/macb_main.c | 61 +++++++++++++++++++-----
2 files changed, 61 insertions(+), 15 deletions(-)
diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index 0647689f9796..b59840f5c023 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -645,10 +645,17 @@
#define GEM_CLK_DIV96 5
/* Constants for MAN register */
-#define MACB_MAN_SOF 1
-#define MACB_MAN_WRITE 1
-#define MACB_MAN_READ 2
-#define MACB_MAN_CODE 2
+#define MACB_MAN_C22_SOF 1
+#define MACB_MAN_C22_WRITE 1
+#define MACB_MAN_C22_READ 2
+#define MACB_MAN_C22_CODE 2
+
+#define MACB_MAN_C45_SOF 0
+#define MACB_MAN_C45_ADDR 0
+#define MACB_MAN_C45_WRITE 1
+#define MACB_MAN_C45_POST_READ_INCR 2
+#define MACB_MAN_C45_READ 3
+#define MACB_MAN_C45_CODE 2
/* Capability mask bits */
#define MACB_CAPS_ISR_CLEAR_ON_WRITE BIT(0)
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index f1e58801ccf5..bdb57482644c 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -344,11 +344,30 @@ static int macb_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
if (status < 0)
goto mdio_read_exit;
- macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_SOF)
- | MACB_BF(RW, MACB_MAN_READ)
- | MACB_BF(PHYA, mii_id)
- | MACB_BF(REGA, regnum)
- | MACB_BF(CODE, MACB_MAN_CODE)));
+ if (regnum & MII_ADDR_C45) {
+ macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_C45_SOF)
+ | MACB_BF(RW, MACB_MAN_C45_ADDR)
+ | MACB_BF(PHYA, mii_id)
+ | MACB_BF(REGA, (regnum >> 16) & 0x1F)
+ | MACB_BF(DATA, regnum & 0xFFFF)
+ | MACB_BF(CODE, MACB_MAN_C45_CODE)));
+
+ status = macb_mdio_wait_for_idle(bp);
+ if (status < 0)
+ goto mdio_read_exit;
+
+ macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_C45_SOF)
+ | MACB_BF(RW, MACB_MAN_C45_READ)
+ | MACB_BF(PHYA, mii_id)
+ | MACB_BF(REGA, (regnum >> 16) & 0x1F)
+ | MACB_BF(CODE, MACB_MAN_C45_CODE)));
+ } else {
+ macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_C22_SOF)
+ | MACB_BF(RW, MACB_MAN_C22_READ)
+ | MACB_BF(PHYA, mii_id)
+ | MACB_BF(REGA, regnum)
+ | MACB_BF(CODE, MACB_MAN_C22_CODE)));
+ }
status = macb_mdio_wait_for_idle(bp);
if (status < 0)
@@ -377,12 +396,32 @@ static int macb_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
if (status < 0)
goto mdio_write_exit;
- macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_SOF)
- | MACB_BF(RW, MACB_MAN_WRITE)
- | MACB_BF(PHYA, mii_id)
- | MACB_BF(REGA, regnum)
- | MACB_BF(CODE, MACB_MAN_CODE)
- | MACB_BF(DATA, value)));
+ if (regnum & MII_ADDR_C45) {
+ macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_C45_SOF)
+ | MACB_BF(RW, MACB_MAN_C45_ADDR)
+ | MACB_BF(PHYA, mii_id)
+ | MACB_BF(REGA, (regnum >> 16) & 0x1F)
+ | MACB_BF(DATA, regnum & 0xFFFF)
+ | MACB_BF(CODE, MACB_MAN_C45_CODE)));
+
+ status = macb_mdio_wait_for_idle(bp);
+ if (status < 0)
+ goto mdio_write_exit;
+
+ macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_C45_SOF)
+ | MACB_BF(RW, MACB_MAN_C45_WRITE)
+ | MACB_BF(PHYA, mii_id)
+ | MACB_BF(REGA, (regnum >> 16) & 0x1F)
+ | MACB_BF(CODE, MACB_MAN_C45_CODE)
+ | MACB_BF(DATA, value)));
+ } else {
+ macb_writel(bp, MAN, (MACB_BF(SOF, MACB_MAN_C22_SOF)
+ | MACB_BF(RW, MACB_MAN_C22_WRITE)
+ | MACB_BF(PHYA, mii_id)
+ | MACB_BF(REGA, regnum)
+ | MACB_BF(CODE, MACB_MAN_C22_CODE)
+ | MACB_BF(DATA, value)));
+ }
status = macb_mdio_wait_for_idle(bp);
if (status < 0)
--
2.17.1
New parameters added to Cadence ethernet controller DT binding
for USXGMII interface.
Signed-off-by: Parshuram Thombare <[email protected]>
---
Documentation/devicetree/bindings/net/macb.txt | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt
index 63c73fafe26d..dabdf9d3b574 100644
--- a/Documentation/devicetree/bindings/net/macb.txt
+++ b/Documentation/devicetree/bindings/net/macb.txt
@@ -28,6 +28,9 @@ Required properties:
Optional elements: 'rx_clk' applies to cdns,zynqmp-gem
Optional elements: 'tsu_clk'
- clocks: Phandles to input clocks.
+- serdes-rate-gbps External serdes rate.Mandatory for USXGMII mode.
+ 5 - 5G
+ 10 - 10G
The MAC address will be determined using the optional properties
defined in ethernet.txt.
--
2.17.1
This patch add support for high speed USXGMII PCS and 10G
speed in Cadence ethernet controller driver.
Signed-off-by: Parshuram Thombare <[email protected]>
---
drivers/net/ethernet/cadence/macb.h | 41 +++++
drivers/net/ethernet/cadence/macb_main.c | 218 +++++++++++++++++++----
2 files changed, 220 insertions(+), 39 deletions(-)
diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index b59840f5c023..a405aeac74e6 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -85,6 +85,7 @@
#define GEM_USRIO 0x000c /* User IO */
#define GEM_DMACFG 0x0010 /* DMA Configuration */
#define GEM_JML 0x0048 /* Jumbo Max Length */
+#define GEM_HS_MAC_CONFIG 0x0050 /* GEM high speed config */
#define GEM_HRB 0x0080 /* Hash Bottom */
#define GEM_HRT 0x0084 /* Hash Top */
#define GEM_SA1B 0x0088 /* Specific1 Bottom */
@@ -170,6 +171,9 @@
#define GEM_DCFG7 0x0298 /* Design Config 7 */
#define GEM_DCFG8 0x029C /* Design Config 8 */
#define GEM_DCFG10 0x02A4 /* Design Config 10 */
+#define GEM_DCFG12 0x02AC /* Design Config 12 */
+#define GEM_USX_CONTROL 0x0A80 /* USXGMII control register */
+#define GEM_USX_STATUS 0x0A88 /* USXGMII status register */
#define GEM_TXBDCTRL 0x04cc /* TX Buffer Descriptor control register */
#define GEM_RXBDCTRL 0x04d0 /* RX Buffer Descriptor control register */
@@ -277,6 +281,8 @@
#define MACB_IRXFCS_SIZE 1
/* GEM specific NCR bitfields. */
+#define GEM_ENABLE_HS_MAC_OFFSET 31
+#define GEM_ENABLE_HS_MAC_SIZE 1
#define GEM_TWO_PT_FIVE_GIG_OFFSET 29
#define GEM_TWO_PT_FIVE_GIG_SIZE 1
@@ -468,6 +474,10 @@
#define MACB_REV_OFFSET 0
#define MACB_REV_SIZE 16
+/* Bitfield in HS_MAC_CONFIG */
+#define GEM_HS_MAC_SPEED_OFFSET 0
+#define GEM_HS_MAC_SPEED_SIZE 3
+
/* Bitfields in PCS_CONTROL. */
#define GEM_PCS_CTRL_RST_OFFSET 15
#define GEM_PCS_CTRL_RST_SIZE 1
@@ -513,6 +523,34 @@
#define GEM_RXBD_RDBUFF_OFFSET 8
#define GEM_RXBD_RDBUFF_SIZE 4
+/* Bitfields in DCFG12. */
+#define GEM_HIGH_SPEED_OFFSET 26
+#define GEM_HIGH_SPEED_SIZE 1
+
+/* Bitfields in USX_CONTROL. */
+#define GEM_USX_CTRL_SPEED_OFFSET 14
+#define GEM_USX_CTRL_SPEED_SIZE 3
+#define GEM_SERDES_RATE_OFFSET 12
+#define GEM_SERDES_RATE_SIZE 2
+#define GEM_RX_SCR_BYPASS_OFFSET 9
+#define GEM_RX_SCR_BYPASS_SIZE 1
+#define GEM_TX_SCR_BYPASS_OFFSET 8
+#define GEM_TX_SCR_BYPASS_SIZE 1
+#define GEM_RX_SYNC_RESET_OFFSET 2
+#define GEM_RX_SYNC_RESET_SIZE 1
+#define GEM_TX_EN_OFFSET 1
+#define GEM_TX_EN_SIZE 1
+#define GEM_SIGNAL_OK_OFFSET 0
+#define GEM_SIGNAL_OK_SIZE 1
+
+/* Bitfields in USX_STATUS. */
+#define GEM_USX_TX_FAULT_OFFSET 28
+#define GEM_USX_TX_FAULT_SIZE 1
+#define GEM_USX_RX_FAULT_OFFSET 27
+#define GEM_USX_RX_FAULT_SIZE 1
+#define GEM_USX_BLOCK_LOCK_OFFSET 0
+#define GEM_USX_BLOCK_LOCK_SIZE 1
+
/* Bitfields in TISUBN */
#define GEM_SUBNSINCR_OFFSET 0
#define GEM_SUBNSINCR_SIZE 16
@@ -673,6 +711,7 @@
#define MACB_CAPS_MACB_IS_GEM BIT(31)
#define MACB_CAPS_PCS BIT(24)
#define MACB_CAPS_MACB_IS_GEM_GXL BIT(25)
+#define MACB_CAPS_HIGH_SPEED BIT(26)
#define MACB_GEM7010_IDNUM 0x009
#define MACB_GEM7014_IDNU 0x107
@@ -752,6 +791,7 @@
})
#define MACB_READ_NSR(bp) macb_readl(bp, NSR)
+#define GEM_READ_USX_STATUS(bp) gem_readl(bp, USX_STATUS)
/* struct macb_dma_desc - Hardware DMA descriptor
* @addr: DMA address of data buffer
@@ -1265,6 +1305,7 @@ struct macb {
struct macb_pm_data pm_data;
struct phylink *pl;
struct phylink_config pl_config;
+ u32 serdes_rate;
};
#ifdef CONFIG_MACB_USE_HWSTAMP
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index bdb57482644c..3146b97eac25 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -87,6 +87,20 @@ static struct sifive_fu540_macb_mgmt *mgmt;
#define MACB_WOL_HAS_MAGIC_PACKET (0x1 << 0)
#define MACB_WOL_ENABLED (0x1 << 1)
+enum {
+ HS_MAC_SPEED_100M,
+ HS_MAC_SPEED_1000M,
+ HS_MAC_SPEED_2500M,
+ HS_MAC_SPEED_5000M,
+ HS_MAC_SPEED_10000M,
+ HS_MAC_SPEED_25000M,
+};
+
+enum {
+ MACB_SERDES_RATE_5_PT_15625Gbps = 5,
+ MACB_SERDES_RATE_10_PT_3125Gbps = 10,
+};
+
/* Graceful stop timeouts in us. We should allow up to
* 1 frame time (10 Mbits/s, full-duplex, ignoring collisions)
*/
@@ -96,6 +110,8 @@ static struct sifive_fu540_macb_mgmt *mgmt;
#define MACB_MDIO_TIMEOUT 1000000 /* in usecs */
+#define MACB_USX_BLOCK_LOCK_TIMEOUT 1000000 /* in usecs */
+
/* DMA buffer descriptor might be different size
* depends on hardware configuration:
*
@@ -448,24 +464,37 @@ static void macb_set_tx_clk(struct clk *clk, int speed, struct net_device *dev)
if (!clk)
return;
- switch (speed) {
- case SPEED_10:
- rate = 2500000;
- break;
- case SPEED_100:
- rate = 25000000;
- break;
- case SPEED_1000:
- rate = 125000000;
- break;
- case SPEED_2500:
- if (bp->caps & MACB_CAPS_MACB_IS_GEM_GXL)
- rate = 312500000;
- else
+ if (bp->phy_interface == PHY_INTERFACE_MODE_USXGMII) {
+ switch (bp->serdes_rate) {
+ case MACB_SERDES_RATE_5_PT_15625Gbps:
+ rate = 78125000;
+ break;
+ case MACB_SERDES_RATE_10_PT_3125Gbps:
+ rate = 156250000;
+ break;
+ default:
+ return;
+ }
+ } else {
+ switch (speed) {
+ case SPEED_10:
+ rate = 2500000;
+ break;
+ case SPEED_100:
+ rate = 25000000;
+ break;
+ case SPEED_1000:
rate = 125000000;
- break;
- default:
- return;
+ break;
+ case SPEED_2500:
+ if (bp->caps & MACB_CAPS_MACB_IS_GEM_GXL)
+ rate = 312500000;
+ else
+ return;
+ break;
+ default:
+ return;
+ }
}
rate_rounded = clk_round_rate(clk, rate);
@@ -494,6 +523,21 @@ static void gem_phylink_validate(struct phylink_config *pl_config,
__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
switch (state->interface) {
+ case PHY_INTERFACE_MODE_USXGMII:
+ case PHY_INTERFACE_MODE_10GKR:
+ if (bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE) {
+ phylink_set(mask, 10000baseCR_Full);
+ phylink_set(mask, 10000baseER_Full);
+ phylink_set(mask, 10000baseKR_Full);
+ phylink_set(mask, 10000baseLR_Full);
+ phylink_set(mask, 10000baseLRM_Full);
+ phylink_set(mask, 10000baseSR_Full);
+ phylink_set(mask, 10000baseT_Full);
+ phylink_set(mask, 5000baseT_Full);
+ phylink_set(mask, 2500baseX_Full);
+ phylink_set(mask, 1000baseX_Full);
+ }
+ /* fallthrough */
case PHY_INTERFACE_MODE_SGMII:
if (bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE) {
phylink_set(mask, 2500baseT_Full);
@@ -516,6 +560,7 @@ static void gem_phylink_validate(struct phylink_config *pl_config,
phylink_set(mask, 100baseT_Half);
phylink_set(mask, 100baseT_Full);
break;
+
case PHY_INTERFACE_MODE_1000BASEX:
case PHY_INTERFACE_MODE_2500BASEX:
phylink_set(mask, 1000baseT_Full);
@@ -537,6 +582,99 @@ static int gem_phylink_mac_link_state(struct phylink_config *pl_config,
return -EOPNOTSUPP;
}
+static int macb_wait_for_usx_block_lock(struct macb *bp)
+{
+ u32 val;
+
+ return readx_poll_timeout(GEM_READ_USX_STATUS, bp, val,
+ val & GEM_BIT(USX_BLOCK_LOCK),
+ 1, MACB_USX_BLOCK_LOCK_TIMEOUT);
+}
+
+static inline int gem_mac_usx_configure(struct macb *bp, int spd)
+{
+ u32 speed, config;
+
+ gem_writel(bp, NCFGR, GEM_BIT(PCSSEL) |
+ (~GEM_BIT(SGMIIEN) & gem_readl(bp, NCFGR)));
+ gem_writel(bp, NCR, gem_readl(bp, NCR) |
+ GEM_BIT(ENABLE_HS_MAC));
+ gem_writel(bp, NCFGR, gem_readl(bp, NCFGR) |
+ MACB_BIT(FD));
+ config = gem_readl(bp, USX_CONTROL);
+ config = GEM_BFINS(SERDES_RATE, bp->serdes_rate, config);
+ config &= ~GEM_BIT(TX_SCR_BYPASS);
+ config &= ~GEM_BIT(RX_SCR_BYPASS);
+ gem_writel(bp, USX_CONTROL, config |
+ GEM_BIT(TX_EN));
+ config = gem_readl(bp, USX_CONTROL);
+ gem_writel(bp, USX_CONTROL, config | GEM_BIT(SIGNAL_OK));
+ if (macb_wait_for_usx_block_lock(bp) < 0) {
+ netdev_warn(bp->dev, "USXGMII block lock failed");
+ return -ETIMEDOUT;
+ }
+
+ switch (spd) {
+ case SPEED_10000:
+ if (bp->serdes_rate >= MACB_SERDES_RATE_10_PT_3125Gbps) {
+ speed = HS_MAC_SPEED_10000M;
+ } else {
+ netdev_warn(bp->dev, "10G speed isn't supported by HW");
+ netdev_warn(bp->dev, "Setting speed to 1G");
+ speed = HS_MAC_SPEED_1000M;
+ }
+ break;
+ case SPEED_5000:
+ speed = HS_MAC_SPEED_5000M;
+ break;
+ case SPEED_2500:
+ speed = HS_MAC_SPEED_2500M;
+ break;
+ case SPEED_1000:
+ speed = HS_MAC_SPEED_1000M;
+ break;
+ default:
+ case SPEED_100:
+ speed = HS_MAC_SPEED_100M;
+ break;
+ }
+
+ gem_writel(bp, HS_MAC_CONFIG, GEM_BFINS(HS_MAC_SPEED, speed,
+ gem_readl(bp, HS_MAC_CONFIG)));
+ gem_writel(bp, USX_CONTROL, GEM_BFINS(USX_CTRL_SPEED, speed,
+ gem_readl(bp, USX_CONTROL)));
+ return 0;
+}
+
+static inline void gem_mac_configure(struct macb *bp, int speed)
+{
+ if (bp->phy_interface == PHY_INTERFACE_MODE_SGMII ||
+ bp->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ bp->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
+ gem_writel(bp, NCFGR, GEM_BIT(SGMIIEN) |
+ GEM_BIT(PCSSEL) |
+ gem_readl(bp, NCFGR));
+
+ switch (speed) {
+ case SPEED_2500:
+ gem_writel(bp, NCFGR, GEM_BIT(GBE) |
+ gem_readl(bp, NCFGR));
+ gem_writel(bp, NCR, GEM_BIT(TWO_PT_FIVE_GIG) |
+ gem_readl(bp, NCR));
+ break;
+ case SPEED_1000:
+ gem_writel(bp, NCFGR, GEM_BIT(GBE) |
+ gem_readl(bp, NCFGR));
+ break;
+ case SPEED_100:
+ macb_writel(bp, NCFGR, MACB_BIT(SPD) |
+ macb_readl(bp, NCFGR));
+ break;
+ default:
+ break;
+ }
+}
+
static void gem_mac_config(struct phylink_config *pl_config, unsigned int mode,
const struct phylink_link_state *state)
{
@@ -574,32 +712,20 @@ static void gem_mac_config(struct phylink_config *pl_config, unsigned int mode,
reg &= ~GEM_BIT(GBE);
macb_or_gem_writel(bp, NCFGR, reg);
- if (bp->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- bp->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
- bp->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
- gem_writel(bp, NCFGR, GEM_BIT(SGMIIEN) |
- GEM_BIT(PCSSEL) |
- gem_readl(bp, NCFGR));
-
reg = macb_readl(bp, NCFGR);
if (state->duplex)
reg |= MACB_BIT(FD);
+ macb_or_gem_writel(bp, NCFGR, reg);
- switch (state->speed) {
- case SPEED_2500:
- gem_writel(bp, NCR, GEM_BIT(TWO_PT_FIVE_GIG) |
- gem_readl(bp, NCR));
- break;
- case SPEED_1000:
- reg |= GEM_BIT(GBE);
- break;
- case SPEED_100:
- reg |= MACB_BIT(SPD);
- break;
- default:
- break;
+ if (bp->phy_interface == PHY_INTERFACE_MODE_USXGMII) {
+ if (gem_mac_usx_configure(bp, state->speed) < 0) {
+ spin_unlock_irqrestore(&bp->lock, flags);
+ phylink_mac_change(bp->pl, false);
+ return;
+ }
+ } else {
+ gem_mac_configure(bp, state->speed);
}
- macb_or_gem_writel(bp, NCFGR, reg);
bp->speed = state->speed;
bp->duplex = state->duplex;
@@ -3446,6 +3572,9 @@ static void macb_configure_caps(struct macb *bp,
default:
break;
}
+ dcfg = gem_readl(bp, DCFG12);
+ if (GEM_BFEXT(HIGH_SPEED, dcfg) == 1)
+ bp->caps |= MACB_CAPS_HIGH_SPEED;
dcfg = gem_readl(bp, DCFG2);
if ((dcfg & (GEM_BIT(RX_PKT_BUFF) | GEM_BIT(TX_PKT_BUFF))) == 0)
bp->caps |= MACB_CAPS_FIFO_MODE;
@@ -4434,7 +4563,18 @@ static int macb_probe(struct platform_device *pdev)
} else if (bp->caps & MACB_CAPS_MACB_IS_GEM_GXL) {
u32 interface_supported = 1;
- if (phy_mode == PHY_INTERFACE_MODE_SGMII ||
+ if (phy_mode == PHY_INTERFACE_MODE_USXGMII) {
+ if (!(bp->caps & MACB_CAPS_HIGH_SPEED &&
+ bp->caps & MACB_CAPS_PCS))
+ interface_supported = 0;
+
+ if (of_property_read_u32(np, "serdes-rate-gbps",
+ &bp->serdes_rate)) {
+ netdev_err(dev,
+ "GEM serdes_rate not specified");
+ interface_supported = 0;
+ }
+ } else if (phy_mode == PHY_INTERFACE_MODE_SGMII ||
phy_mode == PHY_INTERFACE_MODE_1000BASEX ||
phy_mode == PHY_INTERFACE_MODE_2500BASEX) {
if (!(bp->caps & MACB_CAPS_PCS))
--
2.17.1
On Fri, Jun 21, 2019 at 09:34:50AM +0100, Parshuram Thombare wrote:
> @@ -486,23 +503,54 @@ static void gem_mac_config(struct phylink_config *pl_config, unsigned int mode,
> {
> struct net_device *netdev = to_net_dev(pl_config->dev);
> struct macb *bp = netdev_priv(netdev);
> + bool change_interface = bp->phy_interface != state->interface;
> unsigned long flags;
>
> spin_lock_irqsave(&bp->lock, flags);
>
> + if (change_interface) {
> + if (bp->phy_interface == PHY_INTERFACE_MODE_SGMII ||
> + bp->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
> + bp->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
> + gem_writel(bp, NCFGR, ~GEM_BIT(SGMIIEN) &
> + ~GEM_BIT(PCSSEL) &
> + gem_readl(bp, NCFGR));
> + gem_writel(bp, NCR, ~GEM_BIT(TWO_PT_FIVE_GIG) &
> + gem_readl(bp, NCR));
> + gem_writel(bp, PCS_CTRL, gem_readl(bp, PCS_CTRL) |
> + GEM_BIT(PCS_CTRL_RST));
> + }
> + bp->phy_interface = state->interface;
> + }
> +
> if (!phylink_autoneg_inband(mode) &&
> (bp->speed != state->speed ||
> - bp->duplex != state->duplex)) {
> + bp->duplex != state->duplex ||
> + change_interface)) {
> u32 reg;
>
> reg = macb_readl(bp, NCFGR);
> reg &= ~(MACB_BIT(SPD) | MACB_BIT(FD));
> if (macb_is_gem(bp))
> reg &= ~GEM_BIT(GBE);
> + macb_or_gem_writel(bp, NCFGR, reg);
> +
> + if (bp->phy_interface == PHY_INTERFACE_MODE_SGMII ||
> + bp->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
> + bp->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
> + gem_writel(bp, NCFGR, GEM_BIT(SGMIIEN) |
> + GEM_BIT(PCSSEL) |
> + gem_readl(bp, NCFGR));
You don't appear to treat SGMII any differently from the 802.3z modes.
They are certainly not the same thing, so this doesn't seem to be
correct. Also, placing this here, I don't see how the MAC gets
configured for SGMII if in-band mode is enabled.
> +
> + reg = macb_readl(bp, NCFGR);
> if (state->duplex)
> reg |= MACB_BIT(FD);
>
> switch (state->speed) {
> + case SPEED_2500:
> + gem_writel(bp, NCR, GEM_BIT(TWO_PT_FIVE_GIG) |
> + gem_readl(bp, NCR));
> + break;
> case SPEED_1000:
> reg |= GEM_BIT(GBE);
> break;
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
On Fri, Jun 21, 2019 at 09:34:50AM +0100, Parshuram Thombare wrote:
> This patch add support for SGMII interface) and
> 2.5Gbps MAC in Cadence ethernet controller driver.
Also, I'm not sure that merely using PHY_INTERFACE_MODE_SGMII with a
speed of 2.5Gbps is really on for up-clocked SGMII.
Cisco SGMII is defined as running at a fixed 1.25Gbps with the control
word indicating whether the negotiated speed is 1G, 100M or 10M, and
the MAC and PHY expect symbols to be replicated the appropriate number
of times for the slower speeds. Cisco SGMII as defined does not
support 2.5Gbps.
The same is true of 802.3z - this defines 1000BASE-X, but we also have
an up-clocked version which we use a separate phy interface mode for
when supporting 2.5Gbps, since it requires both ends to be configured
differently. This appears to be the case with your 2.5Gbps up-clocked
SGMII - the MAC needs to be told to up-clock the link.
So, I'm wondering whether we need PHY_INTERFACE_MODE_2500SGMII, which
means that if the PHY automatically selects between 1G and 2.5G SGMII,
then it needs to automatically change its interface mode reported back
to the MAC - that is, providing it really _does_ use an up-clocked
2.5Gbps SGMII and doesn't actually switch to 2.5Gbps BASE-X instead.
Other PHYs (the 10G Marvell 88x3310) dynamically switch their MAC
facing interface between 10GBASE-R, 2500BASE-X and SGMII depending on
the negotiated link speed, so there is precedent for this already.
Finally, note that it is possible for a mismatched SGMII / BASE-X
link to come up and appear to work, but either end is going to be
interpreting the 16-bit control word differently, which is obviously
incorrect.
Please ensure that details such as "SGMII" vs "BASE-X" are as correct
as possible.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
On Fri, Jun 21, 2019 at 09:33:57AM +0100, Parshuram Thombare wrote:
> Hello !
>
> 2. 0002-net-macb-add-support-for-sgmii-MAC-PHY-interface.patch
> This patch add support for SGMII mode.
Hi Parshuram
What PHYs are using to test this? You mention TI PHY DP83867, but that
seems to be a plain old 10/100/1000 RGMII PHY.
Thanks
Andrew
On Fri, Jun 21, 2019 at 09:34:59AM +0100, Parshuram Thombare wrote:
> This patch modify MDIO read/write functions to support
> communication with C45 PHY.
>
> Signed-off-by: Parshuram Thombare <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Andrew
On Fri, Jun 21, 2019 at 09:34:44AM +0100, Parshuram Thombare wrote:
> @@ -438,115 +439,145 @@ static void macb_set_tx_clk(struct clk *clk, int speed, struct net_device *dev)
> netdev_err(dev, "adjusting tx_clk failed.\n");
> }
>
> -static void macb_handle_link_change(struct net_device *dev)
> +static void gem_phylink_validate(struct phylink_config *pl_config,
> + unsigned long *supported,
> + struct phylink_link_state *state)
> {
> - struct macb *bp = netdev_priv(dev);
> - struct phy_device *phydev = dev->phydev;
> - unsigned long flags;
> - int status_change = 0;
> + struct net_device *netdev = to_net_dev(pl_config->dev);
> + struct macb *bp = netdev_priv(netdev);
> + __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
> +
> + switch (state->interface) {
> + case PHY_INTERFACE_MODE_GMII:
> + case PHY_INTERFACE_MODE_RGMII:
> + if (bp->caps & MACB_CAPS_GIGABIT_MODE_AVAILABLE) {
> + phylink_set(mask, 1000baseT_Full);
> + phylink_set(mask, 1000baseX_Full);
> + if (!(bp->caps & MACB_CAPS_NO_GIGABIT_HALF)) {
> + phylink_set(mask, 1000baseT_Half);
> + phylink_set(mask, 1000baseT_Half);
> + }
> + }
> + /* fallthrough */
> + case PHY_INTERFACE_MODE_MII:
> + case PHY_INTERFACE_MODE_RMII:
> + phylink_set(mask, 10baseT_Half);
> + phylink_set(mask, 10baseT_Full);
> + phylink_set(mask, 100baseT_Half);
> + phylink_set(mask, 100baseT_Full);
> + break;
> + default:
> + break;
PHY_INTERFACE_MODE_NA is used to ascertain the _full_ set of support
from the MAC irrespective of interface mode, so that (eg) SFPs can
select an appropriate interface mode from the subset of capabililties
supported by the SFP and MAC.
Also note this behaviour for MACs that support switching between
2500BASE-X and 1000BASE-X (which are fixed speed BASE-X):
static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
struct phylink_link_state *state)
{
...
/* Half-duplex at speeds higher than 100Mbit is unsupported */
if (pp->comphy || state->interface != PHY_INTERFACE_MODE_2500BASEX) {
phylink_set(mask, 1000baseT_Full);
phylink_set(mask, 1000baseX_Full);
}
if (pp->comphy || state->interface == PHY_INTERFACE_MODE_2500BASEX) {
phylink_set(mask, 2500baseT_Full);
phylink_set(mask, 2500baseX_Full);
}
The idea here is that _if_ we have a comphy, we can reprogram the comphy
to select between 1G and 2.5G speeds. So we offer both 1G and 2.5G
capabilities irrespective of interface mode.
When the interface type is set in mvneta_mac_config(), the comphy is
configured for the link mode, including setting the link speed to either
1.25Gbaud or 3.125Gbaud.
So, the speed of the serdes lane is determined by the selected
PHY_INTERFACE_MODE.
There is additional logic in the mvneta_validate() method to deal with
the selection of 1G and 2.5G modes for BASE-X:
/* We can only operate at 2500BaseX or 1000BaseX. If requested
* to advertise both, only report advertising at 2500BaseX.
*/
phylink_helper_basex_speed(state);
What this does is clear state->advertising, ensuring that only one of
2500BASE_X or 1000BASE_X is shown, and also sets state->interface in
the validate callback accordingly to select the interface mode.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
Hi Andrew,
>On Fri, Jun 21, 2019 at 09:33:57AM +0100, Parshuram Thombare wrote:
>> Hello !
>>
>> 2. 0002-net-macb-add-support-for-sgmii-MAC-PHY-interface.patch
>> This patch add support for SGMII mode.
>
>Hi Parshuram
>
>What PHYs are using to test this? You mention TI PHY DP83867, but that seems to
>be a plain old 10/100/1000 RGMII PHY.
It is DP83867ISRGZ on VCU118 board. This PHY supports SGMII but driver dp83867
doesn't seems to support it, that was the reason previous patch set has patch
trying to configure PHY in SGMII mode from PCI wrapper driver.
Regards,
Parshuram Thombare
On Sat, Jun 22, 2019 at 03:18:42AM +0000, Parshuram Raju Thombare wrote:
> Hi Andrew,
>
> >On Fri, Jun 21, 2019 at 09:33:57AM +0100, Parshuram Thombare wrote:
> >> Hello !
> >>
> >> 2. 0002-net-macb-add-support-for-sgmii-MAC-PHY-interface.patch
> >> This patch add support for SGMII mode.
> >
> >Hi Parshuram
> >
> >What PHYs are using to test this? You mention TI PHY DP83867, but that seems to
> >be a plain old 10/100/1000 RGMII PHY.
> It is DP83867ISRGZ on VCU118 board. This PHY supports SGMII but driver
> dp83867 doesn't seems to support it, that was the reason previous patch
> set has patch trying to configure PHY in SGMII mode from PCI wrapper driver.
There are several versions of the dp83867 phy supporting various
interface modes. It seems the driver has been written for the
DP83867IR and DP83867CR family, presumably TI data sheet SNLS484E.
The DP83867E/IS/CS is covered by a separate data sheet, SNLS504B.
Please note that this PHY does not support 2.5G operation in any
mode.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
On Sat, Jun 22, 2019 at 03:18:42AM +0000, Parshuram Raju Thombare wrote:
> Hi Andrew,
>
> >On Fri, Jun 21, 2019 at 09:33:57AM +0100, Parshuram Thombare wrote:
> >> Hello !
> >>
> >> 2. 0002-net-macb-add-support-for-sgmii-MAC-PHY-interface.patch
> >> This patch add support for SGMII mode.
> >
> >Hi Parshuram
> >
> >What PHYs are using to test this? You mention TI PHY DP83867, but that seems to
> >be a plain old 10/100/1000 RGMII PHY.
> It is DP83867ISRGZ on VCU118 board.
Thanks.
As Russell says, this is still a 10/100/1000 PHY. What are you using
for the higher speeds?
Thanks
Andrew