Subject: [PATCH] spmi: spmi-pmic-arb: Fix hw_irq overflow

Currently, when handling the SPMI summary interrupt, the hw_irq
number is calculated based on SID, Peripheral ID, IRQ index and
APID. This is then passed to irq_find_mapping() to see if a
mapping exists for this hw_irq and if available, invoke the
interrupt handler. Since the IRQ index uses an "int" type, hw_irq
which is of unsigned long data type can take a large value when
SID has its MSB set to 1 and the type conversion happens. Because
of this, irq_find_mapping() returns 0 as there is no mapping
for this hw_irq. This ends up invoking cleanup_irq() as if
the interrupt is spurious whereas it is actually a valid
interrupt. Fix this by using the proper data type (u32) for id.

Cc: [email protected]
Signed-off-by: Subbaraman Narayanamurthy <[email protected]>
---
drivers/spmi/spmi-pmic-arb.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/drivers/spmi/spmi-pmic-arb.c b/drivers/spmi/spmi-pmic-arb.c
index de844b4..bbbd311 100644
--- a/drivers/spmi/spmi-pmic-arb.c
+++ b/drivers/spmi/spmi-pmic-arb.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0-only
/*
- * Copyright (c) 2012-2015, 2017, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2012-2015, 2017, 2021, The Linux Foundation. All rights reserved.
*/
#include <linux/bitmap.h>
#include <linux/delay.h>
@@ -505,8 +505,7 @@ static void cleanup_irq(struct spmi_pmic_arb *pmic_arb, u16 apid, int id)
static void periph_interrupt(struct spmi_pmic_arb *pmic_arb, u16 apid)
{
unsigned int irq;
- u32 status;
- int id;
+ u32 status, id;
u8 sid = (pmic_arb->apid_data[apid].ppid >> 8) & 0xF;
u8 per = pmic_arb->apid_data[apid].ppid & 0xFF;

--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project


2021-02-08 22:08:58

by Stephen Boyd

[permalink] [raw]
Subject: Re: [PATCH] spmi: spmi-pmic-arb: Fix hw_irq overflow

Quoting Subbaraman Narayanamurthy (2021-02-08 11:33:04)
> Currently, when handling the SPMI summary interrupt, the hw_irq
> number is calculated based on SID, Peripheral ID, IRQ index and
> APID. This is then passed to irq_find_mapping() to see if a
> mapping exists for this hw_irq and if available, invoke the
> interrupt handler. Since the IRQ index uses an "int" type, hw_irq
> which is of unsigned long data type can take a large value when
> SID has its MSB set to 1 and the type conversion happens. Because
> of this, irq_find_mapping() returns 0 as there is no mapping
> for this hw_irq. This ends up invoking cleanup_irq() as if
> the interrupt is spurious whereas it is actually a valid
> interrupt. Fix this by using the proper data type (u32) for id.
>
> Cc: [email protected]
> Signed-off-by: Subbaraman Narayanamurthy <[email protected]>
> ---

Applied to spmi-next