Add a new modem compatible string for QTI SC7280 SoCs and introduce the
"qcom,ext-regs" and "qcom,qaccept-regs" bindings needed by the modem
sub-system running on SC7280 SoCs.
Signed-off-by: Sibi Sankar <[email protected]>
---
.../devicetree/bindings/remoteproc/qcom,q6v5.txt | 32 ++++++++++++++++++++--
1 file changed, 30 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
index 494257010629..d802e57701b8 100644
--- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
@@ -15,6 +15,7 @@ on the Qualcomm Hexagon core.
"qcom,msm8996-mss-pil"
"qcom,msm8998-mss-pil"
"qcom,sc7180-mss-pil"
+ "qcom,sc7280-mss-pil"
"qcom,sdm845-mss-pil"
- reg:
@@ -47,6 +48,7 @@ on the Qualcomm Hexagon core.
qcom,msm8996-mss-pil:
qcom,msm8998-mss-pil:
qcom,sc7180-mss-pil:
+ qcom,sc7280-mss-pil:
qcom,sdm845-mss-pil:
must be "wdog", "fatal", "ready", "handover", "stop-ack",
"shutdown-ack"
@@ -87,6 +89,8 @@ on the Qualcomm Hexagon core.
qcom,sc7180-mss-pil:
must be "iface", "bus", "xo", "snoc_axi", "mnoc_axi",
"nav"
+ qcom,sc7280-mss-pil:
+ must be "iface", "xo", "snoc_axi", "offline"
qcom,sdm845-mss-pil:
must be "iface", "bus", "mem", "xo", "gpll0_mss",
"snoc_axi", "mnoc_axi", "prng"
@@ -98,7 +102,7 @@ on the Qualcomm Hexagon core.
reference to the list of 3 reset-controllers for the
wcss sub-system
reference to the list of 2 reset-controllers for the modem
- sub-system on SC7180, SDM845 SoCs
+ sub-system on SC7180, SC7280, SDM845 SoCs
- reset-names:
Usage: required
@@ -107,7 +111,7 @@ on the Qualcomm Hexagon core.
must be "wcss_aon_reset", "wcss_reset", "wcss_q6_reset"
for the wcss sub-system
must be "mss_restart", "pdc_reset" for the modem
- sub-system on SC7180, SDM845 SoCs
+ sub-system on SC7180, SC7280, SDM845 SoCs
For devices where the mba and mpss sub-nodes are not specified, mba/mpss region
should be referenced as follows:
@@ -173,6 +177,9 @@ For the compatible string below the following supplies are required:
qcom,msm8998-mss-pil:
must be "cx", "mx"
qcom,sc7180-mss-pil:
+ must be "cx", "mx", "mss"
+ qcom,sc7280-mss-pil:
+ must be "cx", "mss"
qcom,sdm845-mss-pil:
must be "cx", "mx", "mss"
@@ -198,6 +205,9 @@ For the compatible string below the following supplies are required:
Definition: a phandle reference to a syscon representing TCSR followed
by the three offsets within syscon for q6, modem and nc
halt registers.
+ a phandle reference to a syscon representing TCSR followed
+ by the four offsets within syscon for q6, modem, nc and vq6
+ halt registers on SC7280 SoCs.
For the compatible strings below the following phandle references are required:
"qcom,sc7180-mss-pil"
@@ -208,6 +218,24 @@ For the compatible strings below the following phandle references are required:
by the offset within syscon for conn_box_spare0 register
used by the modem sub-system running on SC7180 SoC.
+For the compatible strings below the following phandle references are required:
+ "qcom,sc7280-mss-pil"
+- qcom,ext-regs:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: two phandles reference to syscons representing TCSR_REG and
+ TCSR register space followed by the two offset within the syscon
+ to force_clk_en/rscc_disable and axim1_clk_off/crypto_clk_off
+ registers respectively.
+
+- qcom,qaccept-regs:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: a phandle reference to a syscon representing TCSR followed
+ by the three offsets within syscon for mdm, cx and axi
+ qaccept registers used by the modem sub-system running on
+ SC7280 SoC.
+
The Hexagon node must contain iommus property as described in ../iommu/iommu.txt
on platforms which do not have TrustZone.
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
On Fri, Jun 25, 2021 at 01:17:32AM +0530, Sibi Sankar wrote:
> Add a new modem compatible string for QTI SC7280 SoCs and introduce the
> "qcom,ext-regs" and "qcom,qaccept-regs" bindings needed by the modem
> sub-system running on SC7280 SoCs.
>
> Signed-off-by: Sibi Sankar <[email protected]>
> ---
> .../devicetree/bindings/remoteproc/qcom,q6v5.txt | 32 ++++++++++++++++++++--
> 1 file changed, 30 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
> index 494257010629..d802e57701b8 100644
> --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
>
> ...
>
> @@ -208,6 +218,24 @@ For the compatible strings below the following phandle references are required:
> by the offset within syscon for conn_box_spare0 register
> used by the modem sub-system running on SC7180 SoC.
>
> +For the compatible strings below the following phandle references are required:
> + "qcom,sc7280-mss-pil"
> +- qcom,ext-regs:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: two phandles reference to syscons representing TCSR_REG and
s/phandles reference/phandle references/
> + TCSR register space followed by the two offset within the syscon
s/offset/offsets/
> + to force_clk_en/rscc_disable and axim1_clk_off/crypto_clk_off
> + registers respectively.
On 2021-06-26 05:13, Matthias Kaehlcke wrote:
> On Fri, Jun 25, 2021 at 01:17:32AM +0530, Sibi Sankar wrote:
>> Add a new modem compatible string for QTI SC7280 SoCs and introduce
>> the
>> "qcom,ext-regs" and "qcom,qaccept-regs" bindings needed by the modem
>> sub-system running on SC7280 SoCs.
>>
>> Signed-off-by: Sibi Sankar <[email protected]>
>> ---
>> .../devicetree/bindings/remoteproc/qcom,q6v5.txt | 32
>> ++++++++++++++++++++--
>> 1 file changed, 30 insertions(+), 2 deletions(-)
>>
>> diff --git
>> a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
>> b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
>> index 494257010629..d802e57701b8 100644
>> --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
>> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt
>>
>> ...
>>
>> @@ -208,6 +218,24 @@ For the compatible strings below the following
>> phandle references are required:
>> by the offset within syscon for conn_box_spare0 register
>> used by the modem sub-system running on SC7180 SoC.
>>
>> +For the compatible strings below the following phandle references are
>> required:
>> + "qcom,sc7280-mss-pil"
>> +- qcom,ext-regs:
>> + Usage: required
>> + Value type: <prop-encoded-array>
>> + Definition: two phandles reference to syscons representing TCSR_REG
>> and
>
> s/phandles reference/phandle references/
>
>> + TCSR register space followed by the two offset within the
>> syscon
>
> s/offset/offsets/
>
>> + to force_clk_en/rscc_disable and axim1_clk_off/crypto_clk_off
>> + registers respectively.
will fix ^^ in the re-spin.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
On Fri, 25 Jun 2021 01:17:32 +0530, Sibi Sankar wrote:
> Add a new modem compatible string for QTI SC7280 SoCs and introduce the
> "qcom,ext-regs" and "qcom,qaccept-regs" bindings needed by the modem
> sub-system running on SC7280 SoCs.
>
> Signed-off-by: Sibi Sankar <[email protected]>
> ---
> .../devicetree/bindings/remoteproc/qcom,q6v5.txt | 32 ++++++++++++++++++++--
> 1 file changed, 30 insertions(+), 2 deletions(-)
>
Acked-by: Rob Herring <[email protected]>