Changes in V5:
- As per Matthias' comments, I've split the patches as below:
1. Add QSPI node
2. Configure SPI-NOR FLASH for sc7280-idp
3. Add QUPv3 wrapper_0 nodes
4. Update QUPv3 UART5 DT node
5. Configure debug uart for sc7280-idp
6. Configure uart7 to support bluetooth on sc7280-idp
7. Add QUPv3 wrapper_1 nodes
Changes in V4:
- As per Stephen's comment updated spi-max-frequency to 37.5MHz, moved
qspi_opp_table from /soc to / (root).
- As per Bjorn's comment, added QUP Wrapper_0 nodes
as separate patch and debug-uart node as separate patch.
- Dropped interconnect votes for wrapper_0 and wrapper_1 node
- Corrected QUP Wrapper_1 SE node's pin control functions like below
QUP Wrapper_0: SE0-SE7 uses qup00 - qup07 pin-cntrl functions.
QUP Wrapper_1: SE0-SE7 uses qup10 - qup17 pin-cntrl functions.
Changes in V3:
- Broken the huge V2 patch into 3 smaller patches.
1. QSPI DT nodes
2. QUP wrapper_0 DT nodes
3. QUP wrapper_1 DT nodes
Changes in V2:
- As per Doug's comments removed pinmux/pinconf subnodes.
- As per Doug's comments split of SPI, UART nodes has been done.
- Moved QSPI node before aps_smmu as per the order.
Rajesh Patil (3):
arm64: dts: sc7280: Configure SPI-NOR FLASH for sc7280-idp
arm64: dts: sc7280: Configure debug uart for sc7280-idp
arm64: dts: sc7280: Configure uart7 to support bluetooth on sc7280-idp
Roja Rani Yarubandi (4):
arm64: dts: sc7280: Add QSPI node
arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
arm64: dts: sc7280: Update QUPv3 UART5 DT node
arm64: dts: sc7280: Add QUPv3 wrapper_1 nodes
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 129 +-
arch/arm64/boot/dts/qcom/sc7280.dtsi | 3181 ++++++++++++++++++++++--------
2 files changed, 2487 insertions(+), 823 deletions(-)
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
Add bluetooth uart pin configuration for sc7280-idp.
Signed-off-by: Rajesh Patil <[email protected]>
---
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 85 ++++++++++++++++++++++++++++++++
1 file changed, 85 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 53993b3..7c106c0 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -297,6 +297,16 @@
vdda18-supply = <&vreg_l1c_1p8>;
};
+&uart7 {
+ status = "okay";
+
+ /delete-property/interrupts;
+ interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+};
+
/* PINCTRL - additions to nodes defined in sc7280.dtsi */
&qspi_cs0 {
@@ -322,6 +332,81 @@
bias-pull-up;
};
+&qup_uart7_cts {
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ bias-pull-down;
+};
+
+&qup_uart7_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ bias-pull-up;
+};
+
+&tlmm {
+ qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+ pins = "gpio28";
+ function = "gpio";
+ /*
+ * Configure a pull-down on CTS to match the pull of
+ * the Bluetooth module.
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+ pins = "gpio29";
+ function = "gpio";
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+ pins = "gpio30";
+ function = "gpio";
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ bias-pull-up;
+ };
+
+ qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+ pins = "gpio31";
+ function = "gpio";
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
+ bias-pull-up;
+ };
+};
+
&sdc1_on {
clk {
bias-disable;
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
From: Roja Rani Yarubandi <[email protected]>
Add QUPv3 wrapper_1 DT nodes for SC7280 SoC.
Signed-off-by: Roja Rani Yarubandi <[email protected]>
Signed-off-by: Rajesh Patil <[email protected]>
---
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 4 +
arch/arm64/boot/dts/qcom/sc7280.dtsi | 749 +++++++++++++++++++++++++++++++
2 files changed, 753 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 7c106c0..65126a7 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -225,6 +225,10 @@
status = "okay";
};
+&qupv3_id_1 {
+ status = "okay";
+};
+
&sdhc_1 {
status = "okay";
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 2dc7e8c..e29af91 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -981,6 +981,435 @@
};
};
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0 0x00ac0000 0 0x2000>;
+ clock-names = "m-ahb", "s-ahb";
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ iommus = <&apps_smmu 0x43 0x0>;
+ status = "disabled";
+
+ i2c8: i2c@a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c8_data_clk>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi8: spi@a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>, <&qup_spi8_cs_gpio>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart8: serial@a80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a80000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart8_cts>, <&qup_uart8_rts>, <&qup_uart8_tx>, <&qup_uart8_rx>;
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c9: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c9_data_clk>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi9: spi@a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>, <&qup_spi9_cs_gpio>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart9: serial@a84000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a84000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart9_cts>, <&qup_uart9_rts>, <&qup_uart9_tx>, <&qup_uart9_rx>;
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c10: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c10_data_clk>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi10: spi@a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>, <&qup_spi10_cs_gpio>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart10: serial@a88000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a88000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart10_cts>, <&qup_uart10_rts>, <&qup_uart10_tx>, <&qup_uart10_rx>;
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c11: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c11_data_clk>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi11: spi@a8c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>, <&qup_spi11_cs_gpio>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart11: serial@a8c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a8c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart11_cts>, <&qup_uart11_rts>, <&qup_uart11_tx>, <&qup_uart11_rx>;
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c12: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c12_data_clk>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi12: spi@a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>, <&qup_spi12_cs_gpio>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart12: serial@a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a90000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart12_cts>, <&qup_uart12_rts>, <&qup_uart12_tx>, <&qup_uart12_rx>;
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c13: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c13_data_clk>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi13: spi@a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>, <&qup_spi13_cs_gpio>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart13: serial@a94000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a94000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart13_cts>, <&qup_uart13_rts>, <&qup_uart13_tx>, <&qup_uart13_rx>;
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c14: i2c@a98000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c14_data_clk>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi14: spi@a98000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>, <&qup_spi14_cs_gpio>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart14: serial@a98000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a98000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart14_cts>, <&qup_uart14_rts>, <&qup_uart14_tx>, <&qup_uart14_rx>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ i2c15: i2c@a9c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_i2c15_data_clk>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core", "qup-config",
+ "qup-memory";
+ status = "disabled";
+ };
+
+ spi15: spi@a9c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>, <&qup_spi15_cs_gpio>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+
+ uart15: serial@a9c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x00a9c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart15_cts>, <&qup_uart15_rts>, <&qup_uart15_tx>, <&qup_uart15_rx>;
+ interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&rpmhpd SC7280_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core", "qup-config";
+ status = "disabled";
+ };
+ };
+
cnoc2: interconnect@1500000 {
reg = <0 0x01500000 0 0x1000>;
compatible = "qcom,sc7280-cnoc2";
@@ -2040,6 +2469,46 @@
function = "qup07";
};
+ qup_i2c8_data_clk:qup-i2c8-data-clk {
+ pins = "gpio32", "gpio33";
+ function = "qup10";
+ };
+
+ qup_i2c9_data_clk:qup-i2c9-data-clk {
+ pins = "gpio36", "gpio37";
+ function = "qup11";
+ };
+
+ qup_i2c10_data_clk:qup-i2c10-data-clk {
+ pins = "gpio40", "gpio41";
+ function = "qup12";
+ };
+
+ qup_i2c11_data_clk:qup-i2c11-data-clk {
+ pins = "gpio44", "gpio45";
+ function = "qup13";
+ };
+
+ qup_i2c12_data_clk:qup-i2c12-data-clk {
+ pins = "gpio48", "gpio49";
+ function = "qup14";
+ };
+
+ qup_i2c13_data_clk:qup-i2c13-data-clk {
+ pins = "gpio52", "gpio53";
+ function = "qup15";
+ };
+
+ qup_i2c14_data_clk:qup-i2c14-data-clk {
+ pins = "gpio56", "gpio57";
+ function = "qup16";
+ };
+
+ qup_i2c15_data_clk:qup-i2c15-data-clk {
+ pins = "gpio60", "gpio61";
+ function = "qup17";
+ };
+
qup_spi0_data_clk: qup-spi0-data-clk {
pins = "gpio0", "gpio1", "gpio2";
function = "qup00";
@@ -2160,6 +2629,126 @@
function = "gpio";
};
+ qup_spi8_data_clk: qup-spi8-data-clk {
+ pins = "gpio32", "gpio33", "gpio34";
+ function = "qup10";
+ };
+
+ qup_spi8_cs: qup-spi8-cs {
+ pins = "gpio35";
+ function = "qup10";
+ };
+
+ qup_spi8_cs_gpio: qup-spi8-cs_gpio {
+ pins = "gpio35";
+ function = "gpio";
+ };
+
+ qup_spi9_data_clk: qup-spi9-data-clk {
+ pins = "gpio36", "gpio37", "gpio38";
+ function = "qup11";
+ };
+
+ qup_spi9_cs: qup-spi9-cs {
+ pins = "gpio39";
+ function = "qup11";
+ };
+
+ qup_spi9_cs_gpio: qup-spi9-cs_gpio {
+ pins = "gpio39";
+ function = "gpio";
+ };
+
+ qup_spi10_data_clk: qup-spi10-data-clk {
+ pins = "gpio40", "gpio41", "gpio42";
+ function = "qup12";
+ };
+
+ qup_spi10_cs: qup-spi10-cs {
+ pins = "gpio43";
+ function = "qup12";
+ };
+
+ qup_spi10_cs_gpio: qup-spi10-cs_gpio {
+ pins = "gpio43";
+ function = "gpio";
+ };
+
+ qup_spi11_data_clk: qup-spi11-data-clk {
+ pins = "gpio44", "gpio45", "gpio46";
+ function = "qup13";
+ };
+
+ qup_spi11_cs: qup-spi11-cs {
+ pins = "gpio47";
+ function = "qup13";
+ };
+
+ qup_spi11_cs_gpio: qup-spi11-cs_gpio {
+ pins = "gpio47";
+ function = "gpio";
+ };
+
+ qup_spi12_data_clk: qup-spi12-data-clk {
+ pins = "gpio48", "gpio49", "gpio50";
+ function = "qup14";
+ };
+
+ qup_spi12_cs: qup-spi12-cs {
+ pins = "gpio51";
+ function = "qup14";
+ };
+
+ qup_spi12_cs_gpio: qup-spi12-cs_gpio {
+ pins = "gpio51";
+ function = "gpio";
+ };
+
+ qup_spi13_data_clk: qup-spi13-data-clk {
+ pins = "gpio52", "gpio53", "gpio54";
+ function = "qup15";
+ };
+
+ qup_spi13_cs: qup-spi13-cs {
+ pins = "gpio55";
+ function = "qup15";
+ };
+
+ qup_spi13_cs_gpio: qup-spi13-cs_gpio {
+ pins = "gpio55";
+ function = "gpio";
+ };
+
+ qup_spi14_data_clk: qup-spi14-data-clk {
+ pins = "gpio56", "gpio57", "gpio58";
+ function = "qup16";
+ };
+
+ qup_spi14_cs: qup-spi14-cs {
+ pins = "gpio59";
+ function = "qup16";
+ };
+
+ qup_spi14_cs_gpio: qup-spi14-cs_gpio {
+ pins = "gpio59";
+ function = "gpio";
+ };
+
+ qup_spi15_data_clk: qup-spi15-data-clk {
+ pins = "gpio60", "gpio61", "gpio62";
+ function = "qup17";
+ };
+
+ qup_spi15_cs: qup-spi15-cs {
+ pins = "gpio63";
+ function = "qup17";
+ };
+
+ qup_spi15_cs_gpio: qup-spi15-cs_gpio {
+ pins = "gpio63";
+ function = "gpio";
+ };
+
qup_uart0_cts: qup-uart0-cts {
pins = "gpio0";
function = "qup00";
@@ -2400,6 +2989,166 @@
bias-bus-hold;
};
};
+
+ qup_uart8_cts: qup-uart8-cts {
+ pins = "gpio32";
+ function = "qup10";
+ };
+
+ qup_uart8_rts: qup-uart8-rts {
+ pins = "gpio33";
+ function = "qup10";
+ };
+
+ qup_uart8_tx: qup-uart8-tx {
+ pins = "gpio34";
+ function = "qup10";
+ };
+
+ qup_uart8_rx: qup-uart8-rx {
+ pins = "gpio35";
+ function = "qup10";
+ };
+
+ qup_uart9_cts: qup-uart9-cts {
+ pins = "gpio36";
+ function = "qup11";
+ };
+
+ qup_uart9_rts: qup-uart9-rts {
+ pins = "gpio37";
+ function = "qup11";
+ };
+
+ qup_uart9_tx: qup-uart9-tx {
+ pins = "gpio38";
+ function = "qup11";
+ };
+
+ qup_uart9_rx: qup-uart9-rx {
+ pins = "gpio39";
+ function = "qup11";
+ };
+
+ qup_uart10_cts: qup-uart10-cts {
+ pins = "gpio40";
+ function = "qup12";
+ };
+
+ qup_uart10_rts: qup-uart10-rts {
+ pins = "gpio41";
+ function = "qup12";
+ };
+
+ qup_uart10_tx: qup-uart10-tx {
+ pins = "gpio42";
+ function = "qup12";
+ };
+
+ qup_uart10_rx: qup-uart10-rx {
+ pins = "gpio43";
+ function = "qup12";
+ };
+
+ qup_uart11_cts: qup-uart11-cts {
+ pins = "gpio44";
+ function = "qup13";
+ };
+
+ qup_uart11_rts: qup-uart11-rts {
+ pins = "gpio45";
+ function = "qup13";
+ };
+
+ qup_uart11_tx: qup-uart11-tx {
+ pins = "gpio46";
+ function = "qup13";
+ };
+
+ qup_uart11_rx: qup-uart11-rx {
+ pins = "gpio47";
+ function = "qup13";
+ };
+
+ qup_uart12_cts: qup-uart12-cts {
+ pins = "gpio48";
+ function = "qup14";
+ };
+
+ qup_uart12_rts: qup-uart12-rts {
+ pins = "gpio49";
+ function = "qup14";
+ };
+
+ qup_uart12_tx: qup-uart12-tx {
+ pins = "gpio50";
+ function = "qup14";
+ };
+
+ qup_uart12_rx: qup-uart12-rx {
+ pins = "gpio51";
+ function = "qup14";
+ };
+
+ qup_uart13_cts: qup-uart13-cts {
+ pins = "gpio52";
+ function = "qup15";
+ };
+
+ qup_uart13_rts: qup-uart13-rts {
+ pins = "gpio53";
+ function = "qup15";
+ };
+
+ qup_uart13_tx: qup-uart13-tx {
+ pins = "gpio54";
+ function = "qup15";
+ };
+
+ qup_uart13_rx: qup-uart13-rx {
+ pins = "gpio55";
+ function = "qup15";
+ };
+
+ qup_uart14_cts: qup-uart14-cts {
+ pins = "gpio56";
+ function = "qup16";
+ };
+
+ qup_uart14_rts: qup-uart14-rts {
+ pins = "gpio57";
+ function = "qup16";
+ };
+
+ qup_uart14_tx: qup-uart14-tx {
+ pins = "gpio58";
+ function = "qup16";
+ };
+
+ qup_uart14_rx: qup-uart14-rx {
+ pins = "gpio59";
+ function = "qup16";
+ };
+
+ qup_uart15_cts: qup-uart15-cts {
+ pins = "gpio60";
+ function = "qup17";
+ };
+
+ qup_uart15_rts: qup-uart15-rts {
+ pins = "gpio61";
+ function = "qup17";
+ };
+
+ qup_uart15_tx: qup-uart15-tx {
+ pins = "gpio62";
+ function = "qup17";
+ };
+
+ qup_uart15_rx: qup-uart15-rx {
+ pins = "gpio63";
+ function = "qup17";
+ };
};
apps_smmu: iommu@15000000 {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
On Thu, Aug 12, 2021 at 01:11:17PM +0530, Rajesh Patil wrote:
> Add bluetooth uart pin configuration for sc7280-idp.
>
> Signed-off-by: Rajesh Patil <[email protected]>
Reviewed-by: Matthias Kaehlcke <[email protected]>