From: Krishna Manikandan <[email protected]>
Add mdss and mdp DT nodes for sc7280.
Signed-off-by: Krishna Manikandan <[email protected]>
Reported-by: kernel test robot <[email protected]>
Reviewed-by: Stephen Boyd <[email protected]>
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Sankeerth Billakanti <[email protected]>
---
Changes in v3:
None
Changes in v2:
- Rename display dt nodes (Stephen Boyd)
- Add clock names one per line for readability (Stephen Boyd)
arch/arm64/boot/dts/qcom/sc7280.dtsi | 90 ++++++++++++++++++++++++++++++++++++
1 file changed, 90 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 365a2e0..a4536b6 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -2704,6 +2704,96 @@
#power-domain-cells = <1>;
};
+ mdss: display-subsystem@ae00000 {
+ compatible = "qcom,sc7280-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ power-domains = <&dispcc DISP_CC_MDSS_CORE_GDSC>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface",
+ "ahb",
+ "core";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
+ assigned-clock-rates = <300000000>;
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "mdp0-mem";
+
+ iommus = <&apps_smmu 0x900 0x402>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdp: display-controller@ae01000 {
+ compatible = "qcom,sc7280-dpu";
+ reg = <0 0x0ae01000 0 0x8f030>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus",
+ "nrt_bus",
+ "iface",
+ "lut",
+ "core",
+ "vsync";
+ assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>;
+ assigned-clock-rates = <300000000>,
+ <19200000>,
+ <19200000>;
+ operating-points-v2 = <&mdp_opp_table>;
+ power-domains = <&rpmhpd SC7280_CX>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ status = "disabled";
+
+ mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-380000000 {
+ opp-hz = /bits/ 64 <380000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-506666667 {
+ opp-hz = /bits/ 64 <506666667>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sc7280-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>;
--
2.7.4
From: Krishna Manikandan <[email protected]>
Add DSI controller and PHY nodes for sc7280.
Signed-off-by: Rajeev Nandan <[email protected]>
Signed-off-by: Krishna Manikandan <[email protected]>
Reviewed-by: Matthias Kaehlcke <[email protected]>
Reviewed-by: Stephen Boyd <[email protected]>
Signed-off-by: Sankeerth Billakanti <[email protected]>
---
Changes in v3:
- Add the dsi_phy clocks (Kuogee Hsieh)
- One clock cell per line (Stephen Boyd)
Changes in v2:
- Drop flags from interrupts (Stephen Boyd)
- Rename dsi-opp-table (Stephen Boyd)
- Rename dsi phy node (Stephen Boyd)
arch/arm64/boot/dts/qcom/sc7280.dtsi | 111 ++++++++++++++++++++++++++++++++++-
1 file changed, 109 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index a4536b6..12c4d32 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -2691,8 +2691,14 @@
reg = <0 0xaf00000 0 0x20000>;
clocks = <&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_DISP_GPLL0_CLK_SRC>,
- <0>, <0>, <0>, <0>, <0>, <0>;
- clock-names = "bi_tcxo", "gcc_disp_gpll0_clk",
+ <&dsi_phy 0>,
+ <&dsi_phy 1>,
+ <0>,
+ <0>,
+ <0>,
+ <0>;
+ clock-names = "bi_tcxo",
+ "gcc_disp_gpll0_clk",
"dsi0_phy_pll_out_byteclk",
"dsi0_phy_pll_out_dsiclk",
"dp_phy_pll_link_clk",
@@ -2768,6 +2774,18 @@
status = "disabled";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+
mdp_opp_table: opp-table {
compatible = "operating-points-v2";
@@ -2792,6 +2810,95 @@
};
};
};
+
+ dsi0: dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ operating-points-v2 = <&dsi_opp_table>;
+ power-domains = <&rpmhpd SC7280_CX>;
+
+ phys = <&dsi_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+
+ dsi_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-187500000 {
+ opp-hz = /bits/ 64 <187500000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-358000000 {
+ opp-hz = /bits/ 64 <358000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+ };
+
+ dsi_phy: phy@ae94400 {
+ compatible = "qcom,sc7280-dsi-phy-7nm";
+ reg = <0 0x0ae94400 0 0x200>,
+ <0 0x0ae94600 0 0x280>,
+ <0 0x0ae94900 0 0x280>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ status = "disabled";
+ };
};
pdc: interrupt-controller@b220000 {
--
2.7.4
Add edp controller and phy DT nodes for sc7280.
Signed-off-by: Krishna Manikandan <[email protected]>
Reviewed-by: Stephen Boyd <[email protected]>
Signed-off-by: Sankeerth Billakanti <[email protected]>
---
Changes in v3:
- Add one clock cell per line (Stephen Boyd)
- Unit address should match first reg property (Stephen Boyd)
- Remove new line (Stephen Boyd)
- Add the dsi_phy clocks in dispcc (Kuogee Hsieh)
Changes in v2:
- Move regulator definitions to board file (Matthias Kaehlcke)
- Move the gpio definitions to board file (Matthias Kaehlcke)
- Move the pinconf to board file (Matthias Kaehlcke)
- Move status property (Stephen Boyd)
- Drop flags from interrupts (Stephen Boyd)
- Add clock names one per line for readability (Stephen Boyd)
- Rename edp-opp-table (Stephen Boyd)
arch/arm64/boot/dts/qcom/sc7280.dtsi | 107 ++++++++++++++++++++++++++++++++++-
1 file changed, 105 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 12c4d32..5ad500e 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -2695,8 +2695,8 @@
<&dsi_phy 1>,
<0>,
<0>,
- <0>,
- <0>;
+ <&edp_phy 0>,
+ <&edp_phy 1>;
clock-names = "bi_tcxo",
"gcc_disp_gpll0_clk",
"dsi0_phy_pll_out_byteclk",
@@ -2784,6 +2784,13 @@
remote-endpoint = <&dsi0_in>;
};
};
+
+ port@1 {
+ reg = <1>;
+ dpu_intf5_out: endpoint {
+ remote-endpoint = <&edp_in>;
+ };
+ };
};
mdp_opp_table: opp-table {
@@ -2899,6 +2906,102 @@
status = "disabled";
};
+
+ msm_edp: edp@aea0000 {
+ compatible = "qcom,sc7280-edp";
+
+ reg = <0 0xaea0000 0 0x200>,
+ <0 0xaea0200 0 0x200>,
+ <0 0xaea0400 0 0xc00>,
+ <0 0xaea1000 0 0x400>;
+
+ interrupt-parent = <&mdss>;
+ interrupts = <14>;
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_EDP_CLKREF_EN>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK>;
+ clock-names = "core_xo",
+ "core_ref",
+ "core_iface",
+ "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface",
+ "stream_pixel";
+ #clock-cells = <1>;
+ assigned-clocks = <&dispcc DISP_CC_MDSS_EDP_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK_SRC>;
+ assigned-clock-parents = <&edp_phy 0>, <&edp_phy 1>;
+
+ phys = <&edp_phy>;
+ phy-names = "dp";
+
+ operating-points-v2 = <&edp_opp_table>;
+ power-domains = <&rpmhpd SC7280_CX>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ edp_in: endpoint {
+ remote-endpoint = <&dpu_intf5_out>;
+ };
+ };
+ };
+
+ edp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ edp_phy: phy@aec2a00 {
+ compatible = "qcom,sc7280-edp-phy";
+
+ reg = <0 0xaec2a00 0 0x19c>,
+ <0 0xaec2200 0 0xa0>,
+ <0 0xaec2600 0 0xa0>,
+ <0 0xaec2000 0 0x1c0>;
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_EDP_CLKREF_EN>;
+ clock-names = "aux",
+ "cfg_ahb";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
};
pdc: interrupt-controller@b220000 {
--
2.7.4