2022-05-07 06:47:50

by Satya Priya

Subject: [PATCH V11 9/9] arm64: dts: qcom: sc7280: Add pm8008 support for sc7280-idp

Add pm8008 infra and regulators support for sc7280 idp.

Signed-off-by: Satya Priya <[email protected]>
---
Changes in V11:
- Add ldos and parent supplies directly under pm8008@8 node.

Changes in V10:
- None.

Changes in V9:
- Added interrupts properties.

Changes in V8:
- Add an extra phandle "pm8008_bus" and then include pm8008 dtsi files inside it.
- Remove output-high from pm8008_active node.

arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 66 ++++++++++++++++++++++++++++++++
1 file changed, 66 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 6a14259..e336f26 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -271,6 +271,63 @@
};
};

+pm8008_bus: &i2c1 {
+ status = "okay";
+};
+
+#include "pm8008.dtsi"
+
+&pm8008 {
+ interrupt-parent = <&tlmm>;
+ interrupts = <24 IRQ_TYPE_EDGE_RISING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm8008_active>;
+
+ reset-gpios = <&pm8350c_gpios 4 GPIO_ACTIVE_LOW>;
+
+ vdd_l1_l2-supply = <&vreg_s8b_1p2>;
+ vdd_l3_l4-supply = <&vreg_s1b_1p8>;
+ vdd_l5-supply = <&vreg_bob>;
+ vdd_l6-supply = <&vreg_bob>;
+ vdd_l7-supply = <&vreg_bob>;
+};
+
+&pm8008_l1 {
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1300000>;
+};
+
+&pm8008_l2 {
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1250000>;
+};
+
+&pm8008_l3 {
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <3000000>;
+};
+
+&pm8008_l4 {
+ regulator-min-microvolt = <1504000>;
+ regulator-max-microvolt = <1600000>;
+};
+
+&pm8008_l5 {
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <3000000>;
+};
+
+&pm8008_l6 {
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <3000000>;
+};
+
+&pm8008_l7 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3544000>;
+};
+
&qfprom {
vcc-supply = <&vreg_l1c_1p8>;
};
@@ -383,6 +440,15 @@
drive-strength = <2>;
};

+&pm8350c_gpios {
+ pm8008_active: pm8008-active {
+ pins = "gpio4";
+ function = "normal";
+ bias-disable;
+ power-source = <0>;
+ };
+};
+
&qspi_cs0 {
bias-disable;
};
--
2.7.4

2022-05-09 02:22:32

by Stephen Boyd

Subject: Re: [PATCH V11 9/9] arm64: dts: qcom: sc7280: Add pm8008 support for sc7280-idp

Quoting Satya Priya (2022-05-05 02:25:39)
> Add pm8008 infra and regulators support for sc7280 idp.
>
> Signed-off-by: Satya Priya <[email protected]>
> ---

Reviewed-by: Stephen Boyd <[email protected]>