2022-05-05 18:16:27

by Srinivasa Rao Mandadapu

Subject: [PATCH v14 4/4] arm64: dts: qcom: sc7280-herobrine: Add lpi pinmux properties for CRD 3.0/3.1

Add LPASS LPI pinctrl properties, which are required for Audio
functionality on herobrine based platforms of rev5+
(aka CRD 3.0/3.1) boards.

Signed-off-by: Srinivasa Rao Mandadapu <[email protected]>
Co-developed-by: Venkata Prasad Potturu <[email protected]>
Signed-off-by: Venkata Prasad Potturu <[email protected]>
---
arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts | 61 +++++++++++++++++++++++
1 file changed, 61 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index deaea3a..3cce107 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -110,6 +110,67 @@ ap_ts_pen_1v8: &i2c13 {
* - If a pin is totally internal to Qcard then it gets Qcard name.
* - If a pin is not hooked up on Qcard, it gets no name.
*/
+&lpass_dmic01_clk {
+ drive-strength = <8>;
+ bias-disable;
+};
+
+&lpass_dmic01_clk_sleep {
+ drive-strength = <2>;
+};
+
+&lpass_dmic01_data {
+ bias-pull-down;
+};
+
+&lpass_dmic23_clk {
+ drive-strength = <8>;
+ bias-disable;
+};
+
+&lpass_dmic23_clk_sleep {
+ drive-strength = <2>;
+};
+
+&lpass_dmic23_data {
+ bias-pull-down;
+};
+
+&lpass_rx_swr_clk {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+};
+
+&lpass_rx_swr_clk_sleep {
+ bias-pull-down;
+};
+
+&lpass_rx_swr_data {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+};
+
+&lpass_rx_swr_data_sleep {
+ bias-pull-down;
+};
+
+&lpass_tx_swr_clk {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+};
+
+&lpass_tx_swr_clk_sleep {
+ bias-pull-down;
+};
+
+&lpass_tx_swr_data {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+};

&mi2s1_data0 {
drive-strength = <6>;
--
2.7.4

2022-05-09 03:39:23

by Matthias Kaehlcke

Subject: Re: [PATCH v14 4/4] arm64: dts: qcom: sc7280-herobrine: Add lpi pinmux properties for CRD 3.0/3.1

On Thu, May 05, 2022 at 08:33:24PM +0530, Srinivasa Rao Mandadapu wrote:
> Add LPASS LPI pinctrl properties, which are required for Audio
> functionality on herobrine based platforms of rev5+
> (aka CRD 3.0/3.1) boards.
>
> Signed-off-by: Srinivasa Rao Mandadapu <[email protected]>
> Co-developed-by: Venkata Prasad Potturu <[email protected]>
> Signed-off-by: Venkata Prasad Potturu <[email protected]>

Reviewed-by: Matthias Kaehlcke <[email protected]>