Hi Nathan,
On Wednesday, 31 May 2017 12:33:57 PDT Nathan Sullivan wrote:
> Support the National Instruments 169445 board.
>
> Signed-off-by: Nathan Sullivan <[email protected]>
> ---
>
> Changes from v4:
>
> - Address Rob Herring's device tree feedback
>
> I'm still unclear on the vmlinux.its.S changes. The linux-mti tree has a
> config in the image tree for each board it supports, and I followed that
> pattern here. Rob was concerned about how the configs would scale wrt
> the number of bootloaders around, but it's really just one per board/dt,
> right?
It is one per board/DT as you say - ie. it's about including multiple DTs into
the FIT/.itb kernel image rather than about producing multiple image formats.
What you've done does indeed match what I've been doing for our boards in the
linux-mti downstream & in code submitted upstream.
I guess it might be nice at some point to break apart the entries in
vmlinux.its.S to a file per board or something, and it'd also be nice if we
had a way to automatically only include boards that make sense for a targeted
ISA - eg. if a board has a little endian MIPS32r2 CPU there's no point
including drivers or DT for it in big endian, MIPS64 or MIPSr6 kernels. Right
now that can only be done manually by specifying BOARDS= when configuring the
kernel.
Still, it's great to see a board support patch like this one rather than the
"copy arch/mips/mti-malta & bodge it" style patches that many have produced
before - so thanks & nice work :)
Thanks,
Paul
>
> ---
> Documentation/devicetree/bindings/mips/ni.txt | 7 ++
> MAINTAINERS | 8 ++
> arch/mips/boot/dts/Makefile | 1 +
> arch/mips/boot/dts/ni/169445.dts | 100
> ++++++++++++++++++++++++ arch/mips/boot/dts/ni/Makefile |
> 7 ++
> arch/mips/configs/generic/board-ni169445.config | 27 +++++++
> arch/mips/generic/Kconfig | 6 ++
> arch/mips/generic/vmlinux.its.S | 25 ++++++
> 8 files changed, 181 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mips/ni.txt
> create mode 100644 arch/mips/boot/dts/ni/169445.dts
> create mode 100644 arch/mips/boot/dts/ni/Makefile
> create mode 100644 arch/mips/configs/generic/board-ni169445.config
>
> diff --git a/Documentation/devicetree/bindings/mips/ni.txt
> b/Documentation/devicetree/bindings/mips/ni.txt new file mode 100644
> index 0000000..722bf2d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mips/ni.txt
> @@ -0,0 +1,7 @@
> +National Instruments MIPS platforms
> +
> +required root node properties:
> + - compatible: must be "ni,169445"
> +
> +CPU Nodes
> + - compatible: must be "mti,mips14KEc"
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 053c3bd..e6662d0 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -9047,6 +9047,14 @@ F: include/linux/sunrpc/
> F: include/uapi/linux/nfs*
> F: include/uapi/linux/sunrpc/
>
> +NI169445 MIPS ARCHITECTURE
> +M: Nathan Sullivan <[email protected]>
> +L: [email protected]
> +S: Maintained
> +F: arch/mips/boot/dts/ni/
> +F: arch/mips/configs/generic/board-ni169445.config
> +F: Documentation/devicetree/bindings/mips/ni.txt
> +
> NILFS2 FILESYSTEM
> M: Ryusuke Konishi <[email protected]>
> L: [email protected]
> diff --git a/arch/mips/boot/dts/Makefile b/arch/mips/boot/dts/Makefile
> index b9db492..27b0f37 100644
> --- a/arch/mips/boot/dts/Makefile
> +++ b/arch/mips/boot/dts/Makefile
> @@ -4,6 +4,7 @@ dts-dirs += img
> dts-dirs += ingenic
> dts-dirs += lantiq
> dts-dirs += mti
> +dts-dirs += ni
> dts-dirs += netlogic
> dts-dirs += pic32
> dts-dirs += qca
> diff --git a/arch/mips/boot/dts/ni/169445.dts
> b/arch/mips/boot/dts/ni/169445.dts new file mode 100644
> index 0000000..6a20036
> --- /dev/null
> +++ b/arch/mips/boot/dts/ni/169445.dts
> @@ -0,0 +1,100 @@
> +/dts-v1/;
> +
> +/ {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "ni,169445";
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + cpu@0 {
> + device_type = "cpu";
> + compatible = "mti,mips14KEc";
> + clocks = <&baseclk>;
> + reg = <0>;
> + };
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x10000000>;
> + };
> +
> + baseclk: baseclock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <50000000>;
> + };
> +
> + cpu_intc: interrupt-controller {
> + #address-cells = <0>;
> + compatible = "mti,cpu-interrupt-controller";
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + };
> +
> + ahb@1f300000 {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x0 0x1f300000 0x80FFF>;
> +
> + gpio1: gpio@1f300010 {
> + compatible = "ni,169445-nand-gpio";
> + reg = <0x10 0x4>;
> + reg-names = "dat";
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + gpio2: gpio@1f300014 {
> + compatible = "ni,169445-nand-gpio";
> + reg = <0x14 0x4>;
> + reg-names = "dat";
> + gpio-controller;
> + #gpio-cells = <2>;
> + no-output;
> + };
> +
> + nand@1f300000 {
> + compatible = "gpio-control-nand";
> + nand-on-flash-bbt;
> + nand-ecc-mode = "soft_bch";
> + nand-ecc-step-size = <512>;
> + nand-ecc-strength = <4>;
> + reg = <0x0 4>;
> + gpios = <&gpio2 0 0>, /* rdy */
> + <&gpio1 1 0>, /* nce */
> + <&gpio1 2 0>, /* ale */
> + <&gpio1 3 0>, /* cle */
> + <&gpio1 4 0>; /* nwp */
> + };
> +
> + serial@1f380000 {
> + compatible = "ns16550a";
> + reg = <0x80000 0x1000>;
> + interrupt-parent = <&cpu_intc>;
> + interrupts = <6>;
> + clocks = <&baseclk>;
> + reg-shift = <0>;
> + };
> +
> + ethernet@1f340000 {
> + compatible = "snps,dwmac-4.10a";
> + interrupt-parent = <&cpu_intc>;
> + interrupts = <5>;
> + interrupt-names = "macirq";
> + reg = <0x40000 0x2000>;
> + clock-names = "stmmaceth", "pclk";
> + clocks = <&baseclk>, <&baseclk>;
> +
> + phy-mode = "rgmii";
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> + };
> +};
> diff --git a/arch/mips/boot/dts/ni/Makefile b/arch/mips/boot/dts/ni/Makefile
> new file mode 100644
> index 0000000..66cfdff
> --- /dev/null
> +++ b/arch/mips/boot/dts/ni/Makefile
> @@ -0,0 +1,7 @@
> +dtb-$(CONFIG_FIT_IMAGE_FDT_NI169445) += 169445.dtb
> +
> +# Force kbuild to make empty built-in.o if necessary
> +obj- += dummy.o
> +
> +always := $(dtb-y)
> +clean-files := *.dtb *.dtb.S
> diff --git a/arch/mips/configs/generic/board-ni169445.config
> b/arch/mips/configs/generic/board-ni169445.config new file mode 100644
> index 0000000..0bae1f8
> --- /dev/null
> +++ b/arch/mips/configs/generic/board-ni169445.config
> @@ -0,0 +1,27 @@
> +CONFIG_FIT_IMAGE_FDT_NI169445=y
> +
> +CONFIG_SERIAL_8250=y
> +CONFIG_SERIAL_8250_CONSOLE=y
> +CONFIG_SERIAL_OF_PLATFORM=y
> +
> +CONFIG_GPIOLIB=y
> +CONFIG_GPIO_SYSFS=y
> +CONFIG_GPIO_GENERIC_PLATFORM=y
> +
> +CONFIG_MTD=y
> +CONFIG_MTD_BLOCK=y
> +CONFIG_MTD_CMDLINE_PARTS=y
> +
> +CONFIG_MTD_NAND_ECC=y
> +CONFIG_MTD_NAND_ECC_BCH=y
> +CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_GPIO=y
> +CONFIG_MTD_NAND_IDS=y
> +
> +CONFIG_MTD_UBI=y
> +CONFIG_MTD_UBI_BLOCK=y
> +
> +CONFIG_NETDEVICES=y
> +CONFIG_STMMAC_ETH=y
> +CONFIG_STMMAC_PLATFORM=y
> +CONFIG_DWMAC_GENERIC=y
> diff --git a/arch/mips/generic/Kconfig b/arch/mips/generic/Kconfig
> index a606b3f..fbf0813 100644
> --- a/arch/mips/generic/Kconfig
> +++ b/arch/mips/generic/Kconfig
> @@ -16,4 +16,10 @@ config LEGACY_BOARD_SEAD3
> Enable this to include support for booting on MIPS SEAD-3 FPGA-based
> development boards, which boot using a legacy boot protocol.
>
> +config FIT_IMAGE_FDT_NI169445
> + bool "Include FDT for NI 169445"
> + help
> + Enable this to include the FDT for the 169445 platform from
> + National Instruments in the FIT kernel image.
> +
> endif
> diff --git a/arch/mips/generic/vmlinux.its.S
> b/arch/mips/generic/vmlinux.its.S index f67fbf1..de851f7 100644
> --- a/arch/mips/generic/vmlinux.its.S
> +++ b/arch/mips/generic/vmlinux.its.S
> @@ -29,3 +29,28 @@
> };
> };
> };
> +
> +#ifdef CONFIG_FIT_IMAGE_FDT_NI169445
> +/ {
> + images {
> + fdt@ni169445 {
> + description = "NI 169445 device tree";
> + data = /incbin/("boot/dts/ni/169445.dtb");
> + type = "flat_dt";
> + arch = "mips";
> + compression = "none";
> + hash@0 {
> + algo = "sha1";
> + };
> + };
> + };
> +
> + configurations {
> + conf@ni169445 {
> + description = "NI 169445 Linux Kernel";
> + kernel = "kernel@0";
> + fdt = "fdt@ni169445";
> + };
> + };
> +};
> +#endif